American Standard Enfield 2373.821 User Manual

4

6

14

5

SLOT

MOUNTING
SURFACE

Turn off hot and cold water
supplies before beginning.

CAUTION

Insert SPOUT (1) and CABLE CONNECTOR (14) through center hole, making sure
the SPOUT ESCUTCHEON (2) and SEAL WASHER (3) are properly seated.

Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT
SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting
hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.

Tighten LOCKNUT (6) firmly. Fig. A.

Tighten LOCKNUT (11) with WRENCH (8) (supplied) to secure VALVE
BODY (13). Repeat above steps for opposite VALVE BODY (13A).

Install LOCKNUT (11) and RUBBER WASHER (12) onto VALVE BODY (13).
From under side of mounting surface, install VALVE BODY (13) through valve
mounting holes. Threads of VALVE BODY (13) should extent at least 5/16
of a inch above mounting surface top. Fig. B. Thread DECK ADAPTER (10)
onto VALVE BODY (13) until snug against internal stop. If necessary, adjust
LOCKNUT (11).

1

1A

Certified to comply with ANSI A112.18.1

Installation

Instructions

Spread Lavatory Faucet

with the Speed Connect™ Drain

INSTALL SPOUT

INSTALL VALVE BODY

1

2

1

8

10

9

12

11

13

13a

10

9

12

11

3

Place RUBBER RING (9) into DECK ADAPTER (10).

13

5/16'' MIN.

7

Adjustable Wrench Screwdriver Channel Locks

Recommended tools

Tubing Cutter

Fig. A.

Fig. B.

1

M 9 6 8 3 0 1 R e v. 1 . 3

ENFIELD

2373.801

2373.821

1

2

DRAIN
OUTLET

1

3

4

Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Speed Connect™ Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the first time, every time.

M 9 6 8 3 0 1 R e v. 1 . 3 M 9 6 8 3 0 1 R e v. 1 . 3 M 9 6 8 3 0 1 R e v. 1 . 3

1

DOWN

WHITE FO AM
GASKET
NOT VISI BLE

DRAIN
FLANGE

Fig. A. Fig. B.

6

POP-UP KNOB (1) must be fully down. Fig. B.

FLANGE GASKET AND POP-UP KNOB

Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. A.

Thread FLANGE (1) counter-clockwise and remove
FLANGE (1) and FOAM GASKET (2) from drain
body. Fig. A.

Thread LOCKNUT (3) clock-wise to bottom of
drain body. Push GASKET (4) down against
LOCKNUT (3). Fig. B.

POP-UP DRAIN

Tighten TAILPIECE (4) on DRAIN BODY before
installing DRAIN BODY. Fig. B.

2

4

3

2

TIGHTEN LOCKNUT

1

REMOVE FLANGE

Remove CLEAR PLASTIC COVER (1).

Remove CARDBOARD SPACER (2) from under
DRAIN POP-UP (3).

2

2

3

3

1

1

Tighten LOCKNUT (1) firmly with Adjustable
Wrench or Channel Locks.

INSTALL DRAIN FROM
BELOW FIXTURE

5

From under side of SINK
install DRAIN BODY (1) up
through drain outlet.

Note: No plumber’s putty
or caulk is required.
The CABLE ATTACHMENT
POINT (2) must face towards
the rear of the SINK.

Install FOAM GASKET (3) and
FLANGE (4) onto drain body
from above SINK and tighten
FLANGE (4) firmly.

4

Fig. A. Fig. B.

Fig. A. Fig. B.

2

DRAIN
OUTLET

1

3

4

REAR OF SINK

DRAIN
BODY

4