American Standard Ellisse Elite 2711E User Manual
ELLISSE ELITE™ 6’ x 48”
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
ELLISSE ELITE™ 6’ x 48” WHIRLPOOL
Comfortable two person design with generous
back support position and integral seat
❏ 2711E (specify White 020, Bone 021, or
Linen 222)
• Acrylic with fiberglass reinforcement
• 2.0 HP self-draining pump/motor
with dry run seal
• Six multi-directional and flow adjustable
jets including:
Three high performance Ideal-flow™ Jets
Three interchangeable Flex-jets™
• Two silent air volume controls
• Deck-mounted On/Off control
• Complete factory installed and tested
whirlpool system
❏ 2711EC (specify White 020, Bone 021, or
Linen 222)
• Same as above with the StayClean™
whirlpool system featuring Antimicrobial
AlphaSan®
Nominal Dimensions: 72” x 48” x 21-1/2"
(1829 x 1220 x 546mm)
© 2003 American Standard Inc.
HD-004
SPS 2711E
Revised 6/03
Components Needed:
❏ Bath Filler*: (specify finish)
❏ Bath Drain: BATH-DRAIN
(specify Chrome 002, Polished Brass 099,
or Satin 295)
Custom Accessories Available:
❏ Pulse Jet Kit: PULSE-JET (two per kit,
specify White 020, Bone 021, or Linen 222)
❏ Soft Jet Kit: SOFT-JET (two per kit, specify
White 020, Bone 021, or Linen 222)
❏ E-Z-Install™ Whirlpool Heater - EZHEAT-100
❏ Tile Bead Kit: TILE-BEAD
NOTE: Roughing-in dimensions and product specifications shown on reverse side of page.
Compliance Certifications Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
* See American Standard Faucet Selector
NOTE: E-Z-Install™ Whirlpool Heater is designed to
maintain water temperature during operation. It will not
heat cold water to desired bathing temperature.
ELLISSE ELITE™ 6’ x 48”
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE INSTALLATION. SUMP OF BATH IS SUPPORTED BY
INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.
■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
OPTIONAL GRAB BAR KIT No. TILE-BEAD AVAILABLE AND MUST BE ORDERED SEPARATELY.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
● IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY
HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING SYSTEM PIPING. MOUNTING
HOLES DRILLED BY INSTALLER.
SUPPLY PIPING NOT INCLUDED.
IMPORTANT:
Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1.These
measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
1219mm
(48)
305mm
(12)
927mm
(36-1/2)
1829mm
(72)
ON/OFF SWITCH
OUTLINE OF CUTOUT
1791 X 1181
(70-1/2 X 46-1/2)
229mm x 356mm
(9 x 14) FLOOR
CUTOUT
C/L OF
DRAIN
PUMP
102mm
(4)
RECOMMENDED
FITTING
LOCATION
64X279mm
2-1/2 X 11)
51mm
(2)
INTEGRAL
FEET
SUPPORT
GRAB BAR
FITTING AREA
1-1/2 N.P.T.M. THREADS
1-1/2 O.D.TAILPIECE
GENERAL SPECIFICATIONS FOR 2711E WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
OPTIONAL
DECK FITTING
AREA
IN-LINE
HEATER
REMOVABLE
BLANK
(2-1/2)
72 x 48 x 21-1/2 In. (1829 x 1219 x 546mm)
40 Lbs./Sq.Ft. (195 Kgs./Sq.m)
PROVIDE ACCESS
TO PUMP FOR SERVICE
ON ALL INSTALLATIONS
LEVELING STRINGER
(NOT FOR SUPPORT)
C/L OF
OVERFLOW
105mm
(4-1/8)
ROUGH
FLOOR
64mm
965 Lbs. (434 Kg.)
43 x 28 In. (1092 x 711mm)
68 x 38 In. (1727 x 965mm)
14-5/8 In. (371mm)
546mm
(21-1/2)
495mm
(19-1/2)
121mm
(4-3/4)
148 Lbs. (67 Kg.)
95 Gal. (360 L)
74 Gal. (280 L)
2.1 HP, 14.4 AMPS ,120V.PUMP
41.7
81.9
Loading...