American Standard Colony 1583.470 User Manual
COLONY 5’™
WHIRLPOOL AND BATHING POOL
HIGH GLOSS ACRYLIC
COLONY 5’ WHIRLPOOL AND BATHING POOL
❏ 2675.018 Whirlpool featuring System I:
• Acrylic with fiberglass reinforcement
• Dual, molded-in armrests at lumbar area
• 1.0 HP single speed, self-draining pump/motor
with dry run seal
• Factory installed power cord with plug
• Six multi-directional and individually flow-rate
adjustable color-coordinated jets
• Deck-mounted, color-coordinated air switch
On/Off control
• Single, color-coordinated air volume control
• Factory installed and tested whirlpool system
❏ 2675.018C Stay Clean™ Whirlpool Massage
Featuring System I:
• Same as 2675.018 except with the
StayClean™ whirlpool system featuring
Antimicrobial AlphaSan®
❏ 2675.002 Bathing Pool
• Same as above without whirlpool system
Nominal Dimensions: 1524 x 832 x 502mm
(5’ x 32-3/4” x 19-3/4")
© 2003 American Standard Inc.
BV-32
Revised 1/99
To Be Specified - Required:
❏ Color:
❏ Bath Faucet: (specify finish)
❏ Bath Drain: 1583.470 (specify finish)
To Be Specified - Optional:
❏ 5 Foot Acrylic Apron: 9260.018 (specify color)
❏ 5 Foot Apron: 9360.018 (specify color)
❏ Grab Bar Kit: 9822.200-two per kit (specify finish)
❏ Jet Trim Ring Kit: 9860.200-two per kit (specify finish)
❏ Universal Tile Bead Kit: 751755-100
NOTE: Roughing-in dimensions and product
specifica-tions shown on reverse side of page.
Compliance Certifications Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
For color/finish availability and other faucet choices,
please see the Product Selector and Pricing Guide.
COLONY 5’™
WHIRLPOOL AND BATHING POOL
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE
INSTALLATION. SUPPORT OF BATH BY SUMP BEDDING. SUPPORT AND ENCLOSING MATERIAL BY OTHERS.
■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
OPTIONAL 3WALL TILING BEAD KIT AND APRON NO. 9260.018 OR 9360.018, AND GRAB BAR KIT NO. 9822.200
AVAILABLE AND MUST BE ORDERED SEPARATELY.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT:
Dimensions of fixtures are nominal and may vary within the range of tolerances
established by ANSI Standard Z124.1.These measurements are subject to change or cancellation. No
responsibility is assumed for use of superseded or voided pages.
216 mm
(8-1/2)
FINISHED
SEE FITTING
SPECS FOR
DIMENSIONS
832 mm
(32-3/4)
416 mm
(16-3/8)
C/L OF
SUPPLIES
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
1651 & 1981mm
(65 & 78)
WALL
19 mm
(3/4)
305 mm
(12)
38 mm
(1-1/2)
C/L OF
OVERFLOW
79 mm
(3-1/8)
502 mm
(19-3/4)
ROUGH
FLOOR
BATH
SUPPORT
MATERIAL
SERVICING ON ALL INSTALLATIONS
1524 mm
(60)
305 mm
(12)
102 mm
1-1/2 N.P.T.M.
THREADS
(1) AIR VALVE
(4)
229 mm
(9)
CUTOUT IN FLOOR FOR DRAIN
(6) JETS
38 mm
(1-1/2)
1-1/2 O.D.TAILPIECE
PROVIDE ACCESS TO PUMP FOR
OUTLINE OF CUTOUT
1486 mm x 794 mm
(58-1/2 X 31-1/4 )
PUMP
C/L OF
SHOWER ARM
C/L OF
VALVES
C/L OF
SPOUT
■ LEVELING STRINGER
NOT FOR SUPPORT
464 mm
(18-1/4)
70 mm
(2-3/4)
117 mm
(4-5/8)
ON/OFF
SWITCH
216 mm
(8-1/2)
FINISHED
SEE FITTING
SPECS FOR
DIMENSIONS
WALL
832 mm
(32-3/4)
416 mm
(16-3/8)
C/L OF
SUPPLIES
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
1651 & 1981mm
(65 & 78)
19 mm
(3/4)
305 mm
(12)
38 mm
(1-1/2)
C/L OF
OVERFLOW
79 mm
(3-1/8)
502 mm
(19-3/4)
ROUGH
FLOOR
BATH
SUPPORT
MATERIAL
1524 mm
(60)
229 mm
(9)
CUTOUT IN FLOOR FOR DRAIN
305 mm
38 mm
(1-1/2)
(12)
102 mm
1-1/2 N.P.T.M.
THREADS
1-1/2 O.D.TAILPIECE
(4)
OUTLINE OF CUTOUT
1486 mm x 794 mm
(58-1/2 X 31-1/4 )
C/L OF
SHOWER ARM
C/L OF
VALVES
C/L OF
SPOUT
■ LEVELING STRINGER
NOT FOR SUPPORT
464 mm
(18-1/4)
70 mm
(2-3/4)
117 mm
(4-5/8)
GENERAL SPECIFICATIONS FOR 2675 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
60 x 32-3/4 x 19-3/4 In.(1524 x832 x 502mm)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
GENERAL SPECIFICATIONS FOR 2675 BATHING POOL
95 Lbs. (43 Kg.)
604 Lbs. (275 Kg.)
61 Gal. (230 L.)
42 Gal. (159 L.)
20 x 39 In. (508 x 991mm)
27-1/2 x 56 In.(699 x 1422mm)
14-1/4 In. (362mm)
44 Lbs./Sq. Ft. (213 Kgs/Sq. m.)
15.6
29.6
1.1 HP, 9.9 AMPS, 120V.SYSTEM I PUMP
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
27-1/2 x 56 In.(699 mm x 1422mm)
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
60 x 32-3/4 x 19-3/4 In.
(1524mm x 832 mm x 502mm)
70 Lbs. (32 Kg.)
579 Lbs. (261 Kg.)
61 Gal. (230 L.)
20 x 39 In. (508 mm x 991mm)
14-1/4 In. (362mm)
42 Lbs./Sq. Ft. (202 Kgs/Sq. m.)
15.6
29.6
Loading...