American Standard Town Square Pedestal Sink 0790.400, Town Square Pedestal Sink 0790.100, Town Square Pedestal Sink 0790.004, Town Square 0031.000, Town Square Pedestal Sink 0790.800 User Manual

Size:
117.21 Kb
Download

TOWN SQUARE® 24"

PEDESTAL SINK

FIRECLAY

TOWN SQUARE® 24" PEDESTAL SINK

American classic design

Clean straight lines with classic ogee curves

Rear overflow

Supplied with mounting kit

Design-matchedto Town Square fixture and faucets

Right Height™ for greater comfort during use

Made from fireclay

0790.400 Faucet holes on 4" (102mm) centers

0790.800 Faucet holes on 8" (203mm) centers

0790.100 Center hole only

Nominal Dimensions:

24" x 20-1/4"x35-1/2"(610 x 514 x 902mm)

Separate Components:

0790.004 Pedestal top 4" (102mm) centers

0790.008 Pedestal top 8" (203mm) centers

0790.001 Center hole only

0031.000 Pedestal only

Bowl sizes:

14" (356mm) wide

11-3/4"(298mm) front to back

6-1/2"(165mm) deep

Compliance Certifications -

Meets or Exceeds the Following Specifications:

ASME A112.19.9M for Non-VitreousCeramic Fixtures

CAN/CSA B45 Series

To Be Specified:

Color: White Bone Linen Black

Town Square Faucet:

Centerset Lavatory Faucet: 2555.201 (shown)

Widespread Lavatory Faucet: 2555.801

Other Lavatory Faucet*:

Faucet Finish:

Supplies:

1-1/4"Trap:

* See faucet section for additional models available

FINISHED WALL

4"

18-3/4"(476mm)

2-5/8"

4"

 

(102mm)

(67mm)

(102mm)

 

 

 

9-1/2"

 

 

 

 

 

(241mm)

 

 

 

5/8"

 

 

 

 

(16mm)

 

 

 

 

 

20-1/4"

 

 

 

 

 

(514mm)

 

1-3/4"DIA.

 

 

 

 

 

STD. DRAIN

 

 

 

 

 

OUTLET

 

 

 

 

 

 

PED BASE

 

PED TOP

 

 

 

OUTLINE

 

OUTLINE

 

 

 

 

24"

 

 

 

 

 

(610mm)

 

3-3/4"(95mm)

DRAIN

 

 

 

 

 

CHASE

3/8" (10mm) DIA.

 

 

 

7-1/2"

 

 

 

 

(191mm)

 

SLAB ANCHOR

 

 

 

 

 

 

 

 

 

SCREW HOLES

 

 

 

 

 

ON 18-3/4"(476mm)

 

 

6"

 

 

CTRS

 

 

 

 

 

 

 

(152mm)

 

 

 

 

 

SUPPLIES AS

 

 

 

 

 

REQUIRED

35-1/2"

 

 

 

 

1-1/4"O.D.

 

*24"

 

(902mm)

 

 

WASTE

28"

 

(610mm)

 

 

OPEN

 

*22"

 

(711mm)

 

 

 

 

TO

 

(559mm)

 

 

 

 

 

 

3/8" (10mm) DIA.

 

FLOOR

 

 

 

BASE ANCHOR

 

 

 

 

 

SCREW HOLES

 

 

 

 

 

ON 6" (152mm)

 

 

 

 

 

CTRS

 

 

 

 

 

10"

 

 

FINISHED

 

 

(254mm)

 

 

 

 

 

 

 

FLOOR

 

 

 

 

 

 

 

6"

 

 

 

 

 

(152mm)

 

 

 

NOTES:

* DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE SUGGESTED.

PEDESTAL ANCHORING SCREWS NOT INCLUDED.

FOR REINFORCEMENT ONLY. TAKE ACTUAL DIMENSIONS FROM FIXTURE.

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS. INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.9M.

These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.

 

J4

 

© 2008 AS America Inc.

Revised 2/08