HURON™ 4' RECESS BATH
ENAMELED STEEL
HURON™ 4' RECESS BATH
0131.012 Right hand outlet
0133.017 Left hand outlet
Product Features:
•Acid resisting, enameled steel construction
•One-piece recess bath
•Integral apron
•End drain outlet
•Full slip-resistant surface
•Straight tiling flange
Nominal Dimensions:
1181 x 686 x 394mm
(46-1/2" x 27" x 15-1/2")
Compliance Certifications -
Meets or Exceeds the Following Specifications:
•ASME A112.19.4 for Enameled Steel Plumbing Fixtures
•ASTM F-462 for Slip-resistant Bathing Facilities
To Be Specified:
Color:
Bath Faucet*:
Faucet Finish:
Drain:
* See faucet section for additional models available
|
|
SEE FITTING SPECS. |
|
|
||
|
|
FOR DIMENSION |
C/L OF |
|
||
|
|
|
|
|
|
|
|
|
|
|
|
SUPPLIES |
|
|
C/L OF |
|
|
|
|
|
|
SHOWER ARM |
|
|
|
22mm |
|
|
|
|
19mm |
|
||
|
|
|
|
(7/8) |
||
|
|
|
(3/4) |
|
||
|
|
|
|
|
||
|
|
OPTIONAL TO FINISHED FLOOR |
|
|
191mm |
|
|
|
(USUALLY BETWEEN 1651mm (65) |
|
|
(7-1/2) |
|
|
|
& 1981mm (78) |
|
|
|
OUTLET |
|
|
|
|
|
229mmx305mm |
|
|
|
|
|
|
(9x12) FLOOR |
|
|
|
|
|
|
CUTOUT FOR |
|
|
|
|
|
|
DRAIN |
DRAIN |
|
|
|
1181mm |
|
FINISHED |
|
|
|
FINISHED |
|
OF |
||
|
|
(46-1/2) |
|
WALL |
||
|
|
WALL |
|
|||
|
|
|
|
|
C/L |
|
|
|
|
|
|
|
|
|
|
|
|
|
104mm |
|
C/L OF |
|
|
|
|
(4-1/16) |
|
|
|
|
|
51mm |
|
|
VALVE |
|
|
|
|
|
|
|
|
|
|
|
(2) |
|
305mm |
C/L OF |
|
|
327mm |
|
|
SPOUT |
|
|
(12-7/8) |
|
||
(12) |
|
|
|
|||
|
|
|
|
|
||
|
|
25mm |
|
|
|
|
|
67 mm |
(1) |
|
|
|
|
|
102mm |
|
|
|
|
|
|
(2-5/8) |
|
|
|
|
|
|
(4) |
|
|
|
|
|
|
|
394mm |
|
19mm |
19mm |
|
|
|
|
(3/4) |
|
||
|
|
|
(3/4) |
|
||
|
|
(15-1/2) |
|
|
|
|
|
|
|
|
686mm |
|
|
|
|
|
|
|
|
|
|
|
ROUGH |
|
|
(27) |
|
|
|
FLOOR |
|
PLUMBER NOTE – |
|
|
|
|
|
|
PROVIDE SUITABLE SUPPORT AT THIS POINT |
||
76mm |
|
|
|
|
|
|
(3) |
|
38mm |
|
|
|
|
|
|
(1-1/2) |
|
|
|
|
1-1/2 N.P.T. |
1-1/2 O.D. |
|
THREADS |
||
TAILPIECE |
||
|
NOTES:
0133.017 LEFT HAND OUTLET (SHOWN).
0131.012 RIGHT HAND OUTLET (REVERSE DIMENSIONS).
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH BATH FOR ADDITIONAL INFORMATION.
SHOWN WITH POP-UP C.D. & O.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. CONCEALED PIPING NOT INCLUDED.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.4. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.
|
H164 |
|
|
© 2008 AS America Inc. |
Revised 2/08 |
||
|