American Standard One Shower System 2064.724 User Manual

Size:
396.13 Kb
Download

Installation

Instructions

ONE SHOWER SYSTEM

2064.724

Thank you for selecting American-Standard...thebenchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--pleaseread these instructions carefully before you begin.

Certified to comply with ANSI A112.18.1

M968927 Rev. 1.1

Recommended Tools & Materials

 

10mm (3/8)

 

 

 

 

Pencil

 

 

 

 

Drill Bit

 

 

 

 

 

Electric Drill

Level

 

Teflon Tape

Phillips Screwdriver

 

 

 

 

ROUGHING-INDIMENSIONS

FINISHED WALL

13mm

32mm

 

 

 

(1-1/4)

95mm

 

 

(1/2)

 

 

 

1/2" NPT

 

(3-3/4)

 

76mm

 

54mm

 

41mm

(3)

 

 

(2-1/8)

 

(1-5/8)

 

 

 

38mm

 

 

 

 

53mm

(1-1/2)

 

 

 

 

(2-1/16)

 

 

 

 

(48" - 60") (OPTIONAL)

 

 

 

 

620mm

TO FINISHED FLOOR

 

 

 

 

 

 

 

 

586-595mm

(24-3/8)

 

1/2" NPSM HOSE

 

 

(23-1/8,23/3/8)

 

CONNECTION

 

 

 

 

 

RUBBER GASKET

 

 

 

 

60mm

FINISHED

 

 

 

 

(2-3/8")

WALL

 

 

 

 

65mm

 

 

 

 

 

(2-1/2")

 

 

 

19mm

 

 

 

 

 

(3/4)

 

 

 

 

 

 

 

 

203mm

 

 

 

 

 

(8")

33.5mm

 

 

 

151mm

59"

 

 

96mm

(6")

 

(1-3/16D.)

 

 

 

OPTIONAL TO

25mm

 

 

(3-3/4)

(1")

 

 

FINISHED FLOOR

 

 

 

 

 

 

USUALLY BETWEEN

 

 

 

 

915mm TO 1219mm

 

 

 

 

(36)

(48)

FINISHED FLOOR

 

 

 

 

 

1/2" NPSM

 

1

 

 

Turn off hot and cold water

1

 

INSTALL WALL SUPPLY

CAUTION

 

supplies before beginning.

 

 

 

 

 

 

 

 

Supply to WALL SUPPLY (1) is 1/2" NPT. Seerough-inabove for detailed information.

Install RUBBER SEAL (2) onto WALL SUPPLY(1).

 

1/2" NPT

 

2

APPLY SEALANT

Apply sealant or teflon tape to threads of 1/2" NPT supply nipple. Thread WALL SUPPLY (1)

OR TEFLON TAPE

onto supply nipple making a water tight seal. WALL SUPPLY (1) with RUBBER SEAL(2) should be tight against finished wall.

M968927 Rev. 1.1

2 INSTALL WALL BRACKETS

The ADJUSTABLE SHOWER BAR (1) works best if secured to a wall stud or cross brace within the wall, using the SCREWS(2) supplied.

If the ADJUSTABLE SHOWER BAR (1) is to be installed on a tile the ANCHORS(3) and SCREWS(2) should be used.

Determine desired height and location (optional) and mark a center line. If MOUNTING SUPPORT (4) is secured to a stud or cross brace drill small pilot holes for SCREWS(2). IMPORTANT:Make sure that vertical center line is level.

For installations on tiled walls: Use ANCHORS(3) and SCREWS(2) for securing MOUNTING SUPPORT(4) to finished wall.The diameter and depth of the mounting hole should be 10mm (3/8”) dia. and 50mm (2”) deep. Insert the the ANCHORS(3) and tap them with hammer until flush with face of finished wall.

Install RUBBER WASHER (5) in recess of MOUNTING SUPPORT(4). Secure MOUNTING SUPPORT(4) to wall with SCREWS(2).

591mm (23-1/4)

3 INSTALL ADJUSTABLE SHOWER BAR

4

5

3

 

 

C/L

Install ADJUSTABLE SHOWER BAR (1) onto installed MOUNTING SUPPORTS(4).2

 

 

Push ADJUSTABLE SHOWER BAR (1) flush against finished wall and tighten

 

 

 

SET SCREWS (5) with (2.5mm) HEX WRENCH(7) supplied to secure

 

 

 

ADJUSTABLE SHOWER BAR (1) to wall.

 

 

 

 

 

 

RECESS IN

 

 

 

MOUNTING

 

 

 

SUPPORT

5

13

7

 

 

 

 

 

591mm

FINISHED WALL

(23-1/4)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11

1 591mm

(23-1/4)

12

2

4

5

3

FROM CENTER TO

CENTER OF WALL

BRACKETS

10

8

C/L

9

4 INSTALL HOSE AND HAND SHOWER

Install SEAL (8) into COUPLING NUT(9). Connect COUPLING NUT(9) to WALL SUPPLY NIPPLE(10) and tighten.

INSTALL second SEAL (11) into SPRAY HOSE END(12) and connect HAND SHOWER(13) to SPRAY HOSE END(12). Hand tighten.