Page 1
Owner's ManualOwner's Manual
Owner's Manual
Owner's ManualOwner's Manual
Heavy Duty Commercial
Compact [0.6 Cubic Foot]
Microwave Oven
Keep these instructions for future reference.
If the oven changes ownership, this manual must
accompany oven.
Contents
Model Identification .......................... 2
PRECAUTIONS TO AVOID POSSIBLE
EXPOSURE
MICROWAVE
IMPORTANT SAFETY INSTRUCTIONS .. 3
Earthing Instructions ......................... 5
Installation ........................................ 5
Display and Features........................ 6
Using the Oven Control .................... 8
Programming the Oven Control ........ 9
User Options ................................... 10
Care and Cleaning ..........................12
Before Calling for Service ................13
TO EXCESSIVE
ENERGY .................. 3
Page 2
Model Identification
Complete enclosed registration card and promptly return.
If registration card is missing, call Consumer Affairs
Department at 1-800-843-0304 inside U.S.A.
1-319-622-5511 outside U.S.A.
When contacting Amana, provide product information.
Product information is located on oven serial plate.
Record the following information:
Model Number: ____________________________
Manufacturing Number: ______________________
Serial or S/N Number: _______________________
Date of purchase: __________________________
Dealer’s name and address: __________________
________________________________________
________________________________________
Any questions or to locate an authorized servicer, call
1-800-843-0304 inside U.S.A. 1-319-622-5511 outside
U.S.A. If an automated telephone system is reached,
select Commercial Microwave Ovens category. Warranty
service must be performed by an authorized servicer.
Amana also recommends contacting an authorized
servicer if service is required after warranty expires.
2
Page 3
IMPORTANT SAFETY INSTRUCTIONS
Recognize this symbol as a SAFETY message
! WARNING
When using electrical equipment, basic safety precautions should be followed to reduce the risk of burns,
electrical shock, fire, or injury to persons.
1. READ all instructions before using equipment.
2. READ AND FOLLOW the specific
“PRECAUTIONS TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE
ENERGY” on this page.
3. This equipment MUST BE GROUNDED. Connect
only to properly GROUNDED outlet. See
“GROUNDING INSTRUCTIONS” on page 5.
4. Install or locate this equipment ONLY in
accordance with the installation instructions in
this manual.
5. Some products such as whole eggs and sealed
containers—for example, closed glass jars—are
able to explode and SHOULD NOT be HEATED
in this oven.
6. Use this equipment ONLY for its intended use
as described in this manual. Do not use
corrosive chemicals or vapors in this equipment.
This type of oven is specifically designed to
heat, cook, or dry food. It is not designed for
industrial or laboratory use.
7. As with any equipment, CLOSE SUPERVISION
is necessary when used by CHILDREN.
8. See door cleaning instructions on page 11 of
this product safety manual.
9. DO NOT heat baby bottles in oven.
10. Baby food jars shall be open when heated and
contents stirred or shaken before consumption, in
order to avoid burns.
11 DO NOT operate this equipment if it has a
damaged cord or plug, if it is not working properly,
or if it has been damaged or dropped.
12. This equipment, including power cord, must be
serviced ONLY by qualified service personnel.
Special tools are required to service equipment.
Contact nearest authorized service facility for
examination, repair, or adjustment.
13. DO NOT cover or block filter or other openings on
equipment.
14. DO NOT store this equipment outdoors. DO NOT
use this product near water – for example, near a
kitchen sink, in a wet basement, a swimming pool,
or a similar location.
15. DO NOT immerse cord or plug in water.
16. Keep cord AWAY from HEATED surfaces.
17. DO NOT let cord hang over edge of table or
counter.
18. For commercial use only.
PRECAUTIONS TO AVOID POSSIBLE EXPOSURE
TO EXCESSIVE MICROWAVE ENERGY
A. DO NOT attempt to operate this oven with the door open since open door operation can result in harmful
exposure to microwave energy. It is important not to defeat or tamper with the safety interlocks.
B. DO NOT place any object between the oven front face and the door to allow soil or cleaner residue to
accumulate on sealing surfaces.
C. DO NOT operate the oven if it is damaged. It is particularly important that the oven door close properly and
that there is no damage to the:
1. door (bent)
2. hinges and latches (broken or loosened)
3. door seals and sealing surfaces.
D. The oven should not be adjusted or repaired by anyone except properly qualified service personnel.
SAVE THESE INSTRUCTIONS
3
Page 4
IMPORTANT SAFETY INSTRUCTIONS
WARNING
!
To avoid risk of fire in the oven cavity:
a. DO NOT overcook food. Carefully attend oven
when paper, plastic, or other combustible
materials are placed inside the oven to facilitate
cooking.
b. Remove wire twist-ties from paper or plastic
bags before placing bag in oven.
c. If materials inside the oven ignite, keep oven
door CLOSED, turn oven off and disconnect
the power cord, or shut off power at the fuse or
circuit breaker panel.
d. DO NOT use the cavity for storage. DO NOT
leave paper products, cooking utensils, or food
in the cavity when not in use.
WARNING
!
Liquids such as water, coffee, or tea are able to be
overheated beyond the boiling point without appearing
to be boiling due to surface tension of the liquid.
Visible bubbling or boiling when the container is
removed from the microwave oven is not always
present. THIS COULD RESULT IN VERY HOT
LIQUIDS SUDDENLY BOILING OVER WHEN A
SPOON OR OTHER UTENSIL IS INSERTED INTO
THE LIQUID. To reduce the risk of injury to persons:
i) Do not overheat the liquid.
ii) Stir the liquid both before and halfway through
heating it.
iii) Do not use straight-sided containers with narrow
necks.
iv) After heating, allow the container to stand in the
microwave oven for a short time before
removing the container.
v) Use extreme care when inserting a spoon or
other utensil into the container.
! CAUTION
To avoid personal injury or property damage, observe the following:
1. Do not deep fat fry in oven. Fat could overheat
and be hazardous to handle.
2. Do not cook or reheat eggs in shell or with an
unbroken yolk using microwave energy.
Pressure may build up and erupt. Pierce yolk
with fork or knife before cooking.
3. Pierce skin of potatoes, tomatoes, and similar
foods before cooking with microwave energy.
When skin is pierced, steam escapes evenly.
4. Do not operate equipment without load or food
in oven cavity.
5. Use only popcorn in packages designed and
labeled for microwave use. Popping time
varies depending on oven wattage. Do not
continue to heat after popping has stopped.
Popcorn will scorch or burn. Do not leave oven
unattended.
6. Do not use regular cooking thermometers in
oven. Most cooking thermometers contain
mercury and may cause an electrical arc,
malfunction, or damage to oven.
7. Do not use metal utensils in oven.
8. Never use paper, plastic, or other combustible
materials that are not intended for cooking.
9. When cooking with paper, plastic, or other
combustible materials, follow manufacturer's
recommendations on product use.
10. Do not use paper towels which contain nylon or
other synthetic fibers. Heated synthetics could
melt and cause paper to ignite.
11. Do not heat sealed containers or plastic bags in
oven. Food or liquid could expand quickly and
cause container or bag to break. Pierce or open
container or bag before heating.
12. To avoid pacemaker malfunction, consult
physician or pacemaker manufacturer about
effects of microwave energy on pacemaker.
13. An authorized servicer MUST inspect equipment
annually. Record all inspections and repairs for
future use.
SAVE THESE INSTRUCTIONS
4
Page 5
Unpacking Oven
• Inspect oven for damage such as dents in door or inside oven cavity.
• Report any dents or breakage to source of purchase immediately.
Do not attempt to use oven if damaged.
• Remove all materials from oven interior.
• If oven has been stored in extremely cold area, wait a few hours before
connecting power.
Radio Interference
Microwave operation may cause interference to radio, television, or a similar
oven. Reduce or eliminate interference by doing the following:
• Clean door and sealing surfaces of oven according to instructions in
Care and Cleaning section.
• Place radio, television, etc. as far as possible from oven.
• Use a properly installed antenna on radio, television, etc. to obtain
stronger signal reception.
Oven Placement
• Do not install oven next to or above source of heat, such as pizza oven
or deep fat fryer. This could cause microwave oven to operate
improperly and could shorten life of electrical parts.
• Do not block or obstruct oven filter. Allow access for cleaning.
• Install oven on level countertop surface.
• If provided, place warning label in a conspicuous place close to
microwave oven.
• Outlet should be located so that plug is accessible when oven is in place.
Installation
WARNING!
To avoid risk of electrical shock or
death, this oven must be grounded.
WARNING!
To avoid risk of electrical shock
or death, do not alter the plug.
Earthing Instructions
Oven MUST be earthed. Earthing
reduces risk of electric shock by
providing an escape wire for the
electric current, if an electrical short
occurs. This oven is equipped with a
cord having a earth wire with a
earthing plug. The plug must be
plugged into an outlet that is properly
installed and earthed.
Consult a qualified electrician or
servicer if earthing instructions are
not completely understood, or if
doubt exists as to whether the oven
is properly earthed.
A
A
A—Allow at least 7 " (17.8 cm) of clearance around top and sides of oven. Proper air
flow around oven cools electrical components. With restricted air flow, oven may
not operate properly and life of electrical parts is reduced.
B—Allow at least 7 " (17.8 cm) between air discharge on back of oven and back wall.
Oven Clearances
The switching operation of this microwave oven can cause voltage
fluctuations on the supply line. The operation of this oven under unfavorable
voltage supply conditions can have adverse effects. This device is intended
for the connection to a power supply system with a maximum permissible
system impedance Zmax of 0.31 Ohm at the interface point of the user’s
supply. The user has to ensure that this device is connected only to a power
supply system which fulfills the requirement above. If necessary, the user can
ask the public power supply company for the system impedance at the
interface point.
B
Do not use an extension cord.
If the product power cord is too short,
have a qualified electrician install a
three-slot receptacle. This oven
should be plugged into a separate
circuit with the electrical rating as
provided in product specifications
(available on Amana’s wavelink
website). When a microwave oven is
on a circuit with other equipment, an
increase in cooking times may be
required and fuses can be blown.
External Equipotential
Earthing Terminal (export only)
Equipment has secondary earthing
terminal. Terminal provides external
earthing connection used in addition
to earthing prong on plug. Located
on outside of oven back, terminal is
marked with symbol shown below.
5
Page 6
Display and Features
X
Start Pad
The start pad is used to
begin a manual time entry
cooking cycle. It is also used to save
any changes to programming
sequences or user options.
STOP/RESET pad
The STOP/RESET pad
stops a cooking sequence
in progress, clears out any
remaining time, and also ends a
programming or user option cycle.
When the STOP/RESET pad is used
to end a programming or option
change, the changes are discarded.
use this feature, simply program the pad to the desired length of time and
power level. To use this feature, press the pad once and the microwave will
begin cooking.
example 01, 05, or 20. When using the double pad programming, two pads
must be pressed to start the cooking cycle.
specific time entry by using the TIME ENTRY pad. Using manual time entry
does not affect the programmed buttons.
Single Pad Programming
This feature enables each numbered pad to be programmed for a
specific use, such as cooking a certain number of potatoes or
defrosting and then cooking vegetables or other frozen foods. To
Double Pad Programming
This feature enables 100 programmed entries to be made.
Each entry will be assigned a double digit number, for
Manual Time Entry
In addition to programmable pads, this microwave also accepts
X
the original cooking time. The user specifies the percentage and it can be
changed for individual cooking sequences. This feature is very useful for
cooking multiple servings of foods such as potatoes or slices of pizza.
P:--
changes. The user can program up to four different power level changes and
the specific amount of cooking time at each power level. Each power level/
cooking time combination is known as a stage. Up to four stages can be
programmed.
OP:--
Options such as beep volume, maximum cooking time, and the number of
programmable pads can be changed. To change different options, see User
Options in this manual.
X2 Pad
The X2 Pad increases a preset cooking time by a percentage of
Stage Cooking
1
Stage cooking is a cooking sequence with specific power stage
User Options
This microwave can be set for specific user preferences.
6
Page 7
Cooking Display
DISPLAYS DESCRIPTION
Display and Features
READY
00:00
COOK LEVEL
POWER
READY displays when oven control will accept
entries.
Displays cooking time. If stage cooking is
programmed, total cooking time is displayed.
COOK LEVEL displays while oven is operating.
The cooking level is displayed above as a number 1
through 9. If no number is displayed, the oven is
cooking at full power.
POWER is displayed while the oven is generating
microwave energy during a cooking cycle.
Programming Display
DISPLAYS DESCRIPTION
P:0
P:
OP: --
CF:
Displays when oven is in programming mode for
single pad memory only.
Displays when oven is in programming mode for
double pad memory.
Displays when oven is in user option mode. User
options can then be set or specified.
Displays with a numerical cooking factor when the
X2 pad is pressed.
There are words in
the display that never
actually display.
The display is used for many
different models of
microwaves. Depending on the model,
certain words or symbols may never be
highlighted or become visible.
1
P:--
Oven Door
Window
(Some Models)
Oven
Display
Removeable
Splatter Shield
(Not Shown)
Displays briefly when programming a specific
cooking stage. Number (1 through 4) indicates
the stage that is being programmed.
Stainless Steel
Outer Case
Oven Control
Pads
Rear Air Vents
(Some Models)
Door Handle
(Pull to open)
Self-sealing
Base
Oven Cavity Light
(Some Models)
5' 6" Power Cord
7
Page 8
Using the Oven Control
Interrupting
Operation
Open oven door or press
STOP/RESET pad to interrupt
operation. Display continues to
show countdown time. Close door
and press START pad to resume
oven operation.
Canceling Mistakes
• If oven is not cooking, press
STOP/RESET pad to clear display.
• If oven is cooking, press
STOP/RESET pad once to stop
oven, then again to clear display.
• If oven door is open and time
shows in display, close oven
door and press STOP/RESET
pad to clear display.
Manual Time Entry
To cook food using a specific entered time and power level.
1. Open oven door and place food in oven. Close door.
• READY displays. Fan and light will turn on.
2. Press TIME ENTRY pad.
• READY and 0000 display.
• If pad does not work, open and close oven door and try again.
3. Enter cooking time by using the numbered pads.
4. Press POWER LEVEL pad to change power level.
• COOK LEVEL displays with the power setting.
• If a number is not displayed with COOK LEVEL the
microwave is set to full power.
• Press a number pad to adjust power level to desired setting.
5. If stage cooking is desired, press TIME ENTRY and repeat
steps 3 and 4.
• Display changes to cook time and power level for the next stage.
• To add another cooking stage press TIME ENTRY pad again.
• Up to four different stages can be programmed.
6. Press START pad.
• Oven operates and time counts down.
• POWER, COOK LEVEL and cooking time display.
7. At end of cooking cycle oven beeps and shuts off.
X
when cooking more than one serving.
1. Open oven door and place food
2. Press X2 pad.
3. Press desired preprogrammed pad.
4. Oven begins cooking. Displayed
X2 Pad
To increase cooking time
in oven. Close door.
• READY displays. Fan and
light will turn on.
• Amount of time added is a
percentage of the original
preprogrammed cooking time.
• The percentage can be
changed. See Programming
section in this manual.
cooking time is the total of original
cooking time and added X2 time.
Preprogrammed Pads
To cook food using pads preprogrammed with cooking sequences.
1. Open oven door and place food in oven. Close door.
• READY displays. Fan and light will turn on.
2. Press desired pad.
• For single pad entry, press only one pad.
• For double pad entry, press the two pads, in order,
of the double digit number for the desired cooking
sequence.
• To change single or double pad entry option see
User Options section in this manual.
3. Oven begins to cook.
• POWER, COOK LEVEL and total cooking time display.
• For additional cooking time, press preprogrammed pad again
to begin cooking sequence again.
4. At end of cooking cycle oven beeps and shuts off.
Factory Settings
Pad Time Pad Time
1
2
3
4
5
10 sec. 6 1:30 min.
20 sec. 7 2 min.
30 sec. 8 3 min.
45 sec. 9 4 min.
1 min. 0 5 min.
8
Page 9
Programming the Oven Control
Programming Pads
Oven is shipped from the factory for single pad programming. To change
the oven default to allow double pad programming, see User Options.
To change the amount of time or the power level for a preset pad:
1. Open oven door.
• READY displays.
• If door is closed or RESET pad is pressed before programming is
complete, changes are discarded and microwave exits
programming mode.
2. Press and hold pad 1 for approximately 5 seconds.
• This begins programming mode.
• Microwave will beep and P:0 displays. Oven is in
programming mode.
3. Press pad to be reprogrammed.
• Press two pads if reprogramming a double pad program.
• COOK LEVEL and cooking time display.
• A number displays with COOK LEVEL if it is less than full power.
4. Enter cooking time by using the number pads.
5. Press POWER LEVEL pad to change power level if desired.
• Use the number pads to change power level to a lower
power setting.
6. Press START pad to set new programming to the pad.
• If START is not pressed, changes will not be saved.
• P:0 displays
7. Press STOP/RESET pad or close oven door to exit
programming mode.
X
percentage of original cook time,
called a cooking factor, to be added
to a cook sequence.
To change the cooking factor:
1. Open oven door.
2. Press and hold pad 1 for
3. Press pad to be reprogrammed.
4. Press the X2 pad.
5. Press a numbered pad to
6. Press START pad to save changes.
X2 Programming
This feature allows a preset
approximately 5 seconds.
change the cooking factor.
• Pad 5 would change the
cooking factor to 50%.
• Pad 3 would change the
cooking factor to 30%.
Programming Multiple Stages
Stage cooking allows consecutive cooking cycles without interruption.
Up to four different cooking cycles can be programmed into a
memory pad. To use stage cooking:
1. Follow steps 1 through 5 above.
6. Press TIME ENTRY pad.
• Display briefly shows the pad number that is being programmed
and the stage number to the upper right.
• Display changes to cook time and power level for the next
stage.
7. Enter cook time and power level as in steps 4 and 5.
• To enter another cooking stage for that pad, press TIME ENTRY
pad again.
• Up to four different stages can be programmed.
8. Press START pad to set new programming changes to the pad.
9
Page 10
User Options
Didn’t like an option?
Factory settings are marked in bold. To
change the oven back to the factory
setting, simply select the option that is
marked in bold.
My changes weren’t
saved.
In order for any changes to be
saved, the START pad must be
pressed after selecting an option.
Shutting the oven door or pressing the
STOP/RESET pad will not save changes.
Changing user options
Options such as single or double pad programming, beep volume, and
maximum cooking time can be changed to suit individual preferences.
To change options:
1. Open oven door.
• If door is closed or RESET pad is pressed before programming is
complete, changes are discarded and microwave exits programming
mode.
2. Press and hold pad 2 for approximately 5 seconds.
• This begins options mode.
• Microwave will beep and 0P: displays. Microwave is now in
programming mode.
3. Press number pad that controls option to be changed.
• See table below for options.
• Current option will display.
4. Press number pad again to change the option.
• Each time pad is pressed, option will change.
• Match code displayed with code for desired option.
5. Press START pad to save changes.
• To change additional options, repeat steps 3 and 4.
• Changes appear after door is closed or STOP/RESET pad is pressed.
Numbered Pads Display Options (Factory Settings in Bold)
1
End of Cycle Beep
2
Speaker Volume
3
Key Beep
4
Keyboard Enable
Window
5
Add Time During Heating
6
Reset Door Open
7
Maximum Heating Time
8
Manual Operation
9
Double Digit Operation
OP:10
OP:11
OP:12
OP:20
OP:21
OP:22
OP:23
OP:30
OP:31
OP:40
OP:41
OP:42
OP:43
OP:50
OP:51
OP:60
OP:61
OP:70
OP:71
OP:80
OP:81
OP:90
OP:91
3 second continuous beep.
Continuous beep until door is opened.
5 beeps bursts until door is opened.
Eliminates beep.
Sets volume to low.
Sets volume to medium.
Sets volume to high.
Prevents beep when pad is pressed.
Allows beep when pad is pressed.
15 seconds after oven door is opened, keyboard disabled.
30 seconds after oven door is opened, keyboard disabled.
1 minute after oven door is opened, keyboard disabled.
2 minutes after oven door is opened, keyboard disabled.
Prevents adding heating time while oven is heating.
Allows heating time to be changed while oven is heating when a memory pad
is pressed.
Allows oven to resume heating time countdown after door is opened during cycle.
Cancels heating time count down after door is opened during cycle.
Allows 60 minutes of heating time.
Allows 10 minutes of heating time.
Allows use of preprogrammed pads only.
Allows use of manual time entry and preprogrammed pads.
Allows 10 (0-9) preprogrammed pads.
Allows 100 (00-99) preprogrammed pads.
10
Page 11
Care and Cleaning
Replacing Oven Light
WARNING!
To avoid electrical shock which
can cause severe personal
injury or death, unplug power
cord or open circuit breaker to
oven before cleaning or
removing light bulb.
Removing Splatter Shield
Splatter shield keeps top of microwave oven cavity and antenna from becoming soiled. Clean soil from shield with
damp cloth or clean with mild detergent and water. Splatter shield can be removed for easier cleaning.
1. Disconnect electrical supply.
2. Remove screw from side of oven.
3. While wearing protective gloves,
turn light bulb counterclockwise
to remove.
4. Replace light bulb with 230-volt,
25-watt appliance bulb. Do not
over-tighten bulb.
Over-tightening may make bulb
difficult to remove later.
5. Replace light bulb cover before use.
6. Reconnect power supply.
1. Unplug oven to stop antenna from rotating.
2. Place fingers behind shield, pull forward, and then down.
• DO NOT bend antenna.
• If a gap for fingers behind splatter shield does not exist, push up on
splatter shield front. Splatter shield may not be installed fully and cannot
be removed until splatter shield front is properly installed.
3. Reinstall splatter shield by placing front tabs over lip at top of oven cavity
front. Lift back of shield until shield snaps into place.
4. Reconnect power to oven.
PART CARE AND CLEANING RECOMMENDATION
Interior, Exterior, and Door
Discharge Air Vents
Clean microwave oven with mild detergent in warm water using soft sponge or cloth.
Wring sponge or cloth to remove excess water before wiping equipment. If desired, boil a
cup of water in microwave oven to loosen soil before cleaning.
Important:
• Do not use abrasive cleansers or cleaners containing ammonia or citrus.
These could damage finish.
• Never pour water into microwave oven bottom.
• Do not use water pressure type cleaning systems.
Check monthly for a buildup of cooking vapors along intake and discharge louvers on
bottom and back of oven. Clean air vents with damp cloth to ensure proper airflow. Dry
thoroughly.
Shield
up side down
Shield in
correctly
Air Intake Filter
Control Panel
Filter is located below oven door. Clean air intake filter weekly for proper airflow. Wash
filter in hot water and mild detergent. Do not use oven without filter in place. Remove filter
to clean.
Important:
To avoid overheating and oven damage, clean air filter regularly.
1. Grasp filter tab and pull forward. Filter will release from retaining clips.
2. To reinstall, place bottom of filter in clips and push top of filter into position.
Open oven door to deactivate oven timer. Clean with mild detergent in warm water using
soft sponge or cloth.
11
Page 12
Before Calling for Service
! WARNING
To avoid electrical shock which can cause severe personal injury or death, do not remove outer case at any time.
Only an authorized servicer should remove outer case.
An authorized servicer MUST inspect equipment annually.
Record all inspections and repair for future reference.
Problem Possible Cause
Confirm oven is plugged into dedicated circuit.
Oven does not operate.
Oven operates intermittently. Check air filter and discharge areas for obstructions.
If oven does not accept entries
when pad is pressed.
If oven malfunctions or shows
F with a number:
Oven operates but does not heat
food.
Confirm oven is on grounded and polarized circuit.
(Contact electrician to confirm)
Check fuse or circuit breaker.
Make sure oven is on.
Open and close oven door. Press pad again.
Oven control is equipped with a self-diagnostic system. Self-diagnostic
system alerts you if there is a error or problem. When electronic control
signals a problem, follow steps listed below.
1. Record number shown.
2. Unplug oven, wait for 1 minute, and plug in oven.
• Disconnecting electrical supply may eliminate service code. If failure
continues, contact an authorized Amana servicer.
Place one cup of water in oven.
Run for one minute at full power (100%).
If temperature does not rise, oven is not operating correctly. Contact
authorized Amana servicer.
Part No. 12695301
Printed in U.S.A. 12/01
For full product documentation visit:
™
www.amanacommercial.com/wavelink
12
2001 Amana Appliances
Amana, Iowa 52204
Loading...