AT-x510DP-52GTX
Gigabit Ethernet Switch
3517911131517192123
46810122 16 18 2014
x510DP-52GTX
22 24
1000 LINK ACT 10/100 LINK ACT
Installation Guide
27 2925 31 33 35 37 39 41 43 45 47
28 30 32 34 3626 40 42 4438
FDX HDX COL
46 48
SFP+
49
S1/51
CONSOLE
S2/52
50
2662
C613-04066-00 REV B
Copyright © 2013 Allied Telesis, Inc.
All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc.
Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names,
logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners.
Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document without prior
written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for
any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related
to this manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the
possibility of such damages.
Electrical Safety and Emissions Standards
Laser Safety EN60825
This product meets the following standards.
U.S. Federal Communications Commission
Radiated Energy
Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15
of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with this instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void your right to operate
this equipment.
Industry Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
RFI Emissions: FCC Class A, EN55022 Class A, EN61000-3-2, EN61000-3-3, VCCI Class A,
C-TICK, CE
Warning: In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
EMC (Immunity): EN55024
Electrical Safety: EN60950-1 (UL-EU), UL 60950-1 (
CULUS
)
3
Translated Safety Statements
Important: Safety statements that have the symbol are translated into multiple languages in the
Translated Safety Messages document at alliedtelesis.com/support/documentation.
4
Contents
Preface ................................................................................................................................................................................11
Document Conventions ........................................................................................................................................................12
Contacting Allied Telesis ......................................................................................................................................................13
Chapter 1: Overview ..........................................................................................................................................................15
Features ...............................................................................................................................................................................16
10/100/1000 Mbps Twisted Pair Ports ..........................................................................................................................16
SFP+ Slots ....................................................................................................................................................................16
Power Supply Modules..................................................................................................................................................17
Stacking Slots................................................................................................................................................................17
LEDs..............................................................................................................................................................................17
Installation Options........................................................................................................................................................17
MAC Address Table ......................................................................................................................................................17
Management Software and Interfaces ..........................................................................................................................17
Management Methods...................................................................................................................................................17
Front and Rear Panels .........................................................................................................................................................18
Management Panel .............................................................................................................................................................. 19
10/100/1000Base-T Twisted Pair Ports ................................................................................................................................20
Speed ............................................................................................................................................................................20
Duplex Mode .................................................................................................................................................................20
Wiring Configuration......................................................................................................................................................20
Maximum Distance........................................................................................................................................................21
Cable Requirements......................................................................................................................................................21
Port Pinouts................................................................................................................................................................... 21
SFP+ Slots............................................................................................................................................................................22
Stacking SFP+ Slots.............................................................................................................................................................23
eco-friendly Button................................................................................................................................................................24
LEDs.....................................................................................................................................................................................25
LEDs for the Twisted Pair Ports ....................................................................................................................................25
LEDs for the SFP+ Slots ...............................................................................................................................................26
LEDs for the Stacking Slots....................................................................................................
Switch ID LED ...............................................................................................................................................................27
USB Port...............................................................................................................................................................................30
Console Port.........................................................................................................................................................................31
Power Supplies.....................................................................................................................................................................32
.......................................27
Chapter 2: Virtual Chassis Stacking ................................................................................................................................35
Overview...............................................................................................................................................................................36
Stacking Slots.......................................................................................................................................................................37
Stacking Transceivers ..........................................................................................................................................................38
Stacking Port Topologies......................................................................................................................................................40
Master and Member Switches ..............................................................................................................................................44
Selection of the Master Switch ......................................................................................................................................44
ID Numbers ...................................................................................................................................................................45
Specifying Ports in the Command Line Interface..................................................................................................................46
Chapter 3: Beginning the Installation ..............................................................................................................................47
Reviewing Safety Precautions..............................................................................................................................................48
Choosing a Site for the Switches..........................................................................................................................................52
Planning a Stack...................................................................................................................................................................53
5
Contents
Unpacking the Switch ...........................................................................................................................................................55
Chapter 4: Installing the Switch and its Power Supplies ...............................................................................................57
Installing the Power Cord Retaining Clip ..............................................................................................................................58
Installing Power Supply Modules ..........................................................................................................................................59
Overview........................................................................................................................................................................59
Installing a Power Supply ..............................................................................................................................................59
Installing the Switches on a Table or Desktop ......................................................................................................................63
Installing the Switch in an Equipment Rack ..........................................................................................................................64
Connecting AC Power to a Power Supply Module................................................................................................................67
Power Wiring to a DC AT-PWR250R-80 Power Supply Module ..........................................................................................69
Starting a Local Management Session .................................................................................................................................73
Monitoring the Initialization Processes..................................................................................................................................74
Chapter 5: Configuring the Switch for Stand-alone Operations ...................................................................................77
Configuring the Switch for Stand-alone Operations..............................................................................................................78
Disabling VCStack.........................................................................................................................................................78
Confirming the Status of the VCStack Feature..............................................................................................................81
Specifying Ports in the Command Line Interface for Stand-alone Switches.........................................................................83
Chapter 6: Verifying the Status of VCStack and Activating VCStack ...........................................................................85
Verifying the Status of VCStack............................................................................................................................................86
Activating the VCStack Feature............................................................................................................................................87
Activating VCStack ........................................................................................................................................................87
Chapter 7: Cabling the Stacking Ports
Cabling Switches with AT-StackXS/1.0 Transceivers...........................................................................................................92
Cabling Switches with AT-StackOP/0.3 or AT-StackOP/9.0 Transceivers ...........................................................................97
Chapter 8: Powering On the Stack .................................................................................................................................101
Powering On the Switches Individually...............................................................................................................................102
Powering On the Switches Simultaneously ........................................................................................................................104
Verifying the Stack..............................................................................................................................................................106
Setting the Priority Numbers........................................................................................................................................107
Chapter 9: Cabling the Networking Ports ......................................................................................................................109
Cabling the Twisted Pair Ports............................................................................................................................................110
Installing SFP and SFP+ Transceivers ...............................................................................................................................112
Chapter 10: Troubleshooting ..........................................................................................................................................117
Appendix A: Technical Specifications ...........................................................................................................................123
Physical Specifications .......................................................................................................................................................123
Environmental Specifications..............................................................................................................................................123
Power Specifications...........................................................................................................................................................124
Certifications .......................................................................................................................................................................124
RJ-45 Twisted Pair Port Pinouts.........................................................................................................................................125
RJ-45 Style Serial Console Port Pinouts ............................................................................................................................127
Fiber Optic Specifications of the AT-StackOP/0.3 and AT-StackOP/9.0 Transceivers.......................................................128
............................................................................................................................91
6
Figures
Figure 1: Front Panel of the AT-x510DP-52GTX Switch ......................................................................................................18
Figure 2: Back Panel of the Switch.......................................................................................................................................18
Figure 3: AT-x510DP-52GTX Management Panel ...............................................................................................................19
Figure 4: LEDs for the 10/100/1000Base-T Ports.................................................................................................................25
Figure 5: SFP+ Slot LEDs ....................................................................................................................................................26
Figure 6: Switch ID LED .......................................................................................................................................................28
Figure 7: Switch ID LED .......................................................................................................................................................28
Figure 8: Switch ID LEDs in the Low Power Mode ...............................................................................................................29
Figure 9: AT-PWR100R AC Power Supply...........................................................................................................................33
Figure 10: AT-PWR250 AC Power Supply ........................................................................................................................... 33
Figure 11: AT-PWR250R DC Power Supply ........................................................................................................................33
Figure 12: Stacking Transceivers .........................................................................................................................................38
Figure 13: Stack of Two Switches in the Linear Topology....................................................................................................40
Figure 14: Stack of Four Switches in the Linear Topology ...................................................................................................41
Figure 15: Stack of Two Switches in the Ring Topology ......................................................................................................42
Figure 16: Stack of Four Switches in the Ring Topology ......................................................................................................43
Figure 17: PORT Parameter in the Command Line Interface...............................................................................................46
Figure 18: Components of the switch ...................................................................................................................................55
Figure 19: Power Cord Retaining Clip ..................................................................................................................................58
Figure 20: Inserting the Retaining Clip into the Retaining Bracket .......................................................................................58
Figure 21: Removing the rear panel .....................................................................................................................................60
Figure 22: Installing the AT-PWR100R AC Power Supply Module....................................................................
Figure 23: Securing the AT-PWR100R Power Supply Module.............................................................................................61
Figure 24: Installing the Blank Panel on the Power Supply Slot ...........................................................................................62
Figure 25: Turning the Switch Upside Down ........................................................................................................................64
Figure 26: Removing the Rubber Feet .................................................................................................................................64
Figure 27: Attaching the Equipment Rack Brackets .............................................................................................................65
Figure 28: Mounting the Switch Horizontally in an Equipment Rack ....................................................................................66
Figure 29: Mounting the Switch Vertically in an Equipment Rack ........................................................................................66
Figure 30: Power Cord Retaining Clip in the Up Position .....................................................................................................67
Figure 31: Connecting the AC Power Cord ..........................................................................................................................67
Figure 32: DC Terminal Block on the DC AT-PWR250R-80 Power Supply Module ............................................................70
Figure 33: Stripped Wire.......................................................................................................................................................71
Figure 34: Inserting Wires into a DC Terminal Block............................................................................................................71
Figure 35: Connecting the Management Cable to the Console Port ....................................................................................73
Figure 36: Switch Initialization Messages.............................................................................................................................74
Figure 37: Switch Initialization Messages (Continued).........................................................................................................75
Figure 38: Switch Initialization Messages (Continued).........................................................................................................76
Figure 39: User Exec Mode Prompt .....................................................................................................................................78
Figure 40: SHOW STACK Command................................................................................................................................... 79
Figure 41: Moving to the Global Configuration Mode ...........................................................................................................79
Figure 42: Confirmation Prompt for the NO STACK ENABLE Command ............................................................................80
Figure 43: Returning to the Privileged Exec Mode ...............................................................................................................80
Figure 44: Saving the Changes with the WRITE Command.................................................................................................80
Figure 45: Status of a Stacking Slot When VCStack is Disabled .........................................................................................81
Figure 46: Status of a Stacking Slot When VCStack is Enabled ..........................................................................................82
Figure 47: PORT Parameter in the Command Line Interface...............................................................................................83
Figure 48: User Exec Mode Prompt .....................................................................................................................................87
Figure 49: Moving to the Privileged Exec Mode with the ENABLE Command .....................................................................87
...................61
7
Figures
Figure 50: Moving to the Global Configuration Mode with the CONFIGURE TERMINAL Command...................................88
Figure 51: Activating VCStack with the STACK ENABLE Command...................................................................................88
Figure 52: Returning to the Privileged Exec Mode with the EXIT Command .......................................................................88
Figure 53: Saving the Change with the WRITE Command...................................................................................................88
Figure 54: Rebooting the Switch with the REBOOT Command............................................................................................89
Figure 55: Removing the Dust Plug from the S1 Slot ...........................................................................................................92
Figure 56: Removing the Dust Cover from the AT-StackXS/1.0 Transceiver .......................................................................93
Figure 57: Installing the AT-StackXS/1.0 Transceiver in Slot S1..........................................................................................94
Figure 58: Removing the Dust Plug from the S2 Slot ...........................................................................................................95
Figure 59: Installing the AT-StackXS/1.0 Transceiver in Slot S2..........................................................................................96
Figure 60: Handle on the AT-StackOP/0.3 and AT-StackOP/9.0 Transceivers....................................................................97
Figure 61: Installing the AT-StackOP/0.3 or AT-StackOP/9.0 Transceiver...........................................................................98
Figure 62: Removing the Dust Cover from a Stacking Transceiver......................................................................................99
Figure 63: Positioning the Handle in the Upright Position.....................................................................................................99
Figure 64: Connecting the Fiber Optic Cable to the Stacking Transceiver .........................................................................100
Figure 65: SHOW STACK Command.................................................................................................................................106
Figure 66: Moving to the Global Configuration Mode with the CONFIGURE TERMINAL Command.................................107
Figure 67: Returning to the Privileged Exec Mode .............................................................................................................107
Figure 68: Saving the Priority Values with the WRITE Command ......................................................................................108
Figure 69: Removing the Dust Plug from an SFP+ Slot .....................................................................................................113
Figure 70: Installing an SFP or SFP+ Transceiver .............................................................................................................114
Figure 71: Removing the Dust Cover from an SFP or SFP+ Transceiver ..........................................................................114
Figure 72: Positioning the SFP or SFP+ Handle in the Upright Position ............................................................................115
Figure 73: Connecting a Fiber Optic Cable to an SFP or SFP+ Transceiver .....................................................................115
Figure 74: RJ-45 Socket Pin Layout (Front View)...............................................................................................................125
8
Tables
Table 1: Twisted Pair Cable for the 10/100/1000Base-T Ports ...........................................................................................21
Table 2: LEDs on the 10/100/1000Base-T Ports .................................................................................................................25
Table 3: SFP+ Slot LEDs .....................................................................................................................................................27
Table 4: Stacking Slot LEDs ................................................................................................................................................27
Table 5: Stacking Transceivers ...........................................................................................................................................38
Table 6: Operating Distances of the AT-StackOP/0.3 Transceiver .....................................................................................54
Table 7: Physical Specifications ........................................................................................................................................123
Table 8: Environmental Specifications ...............................................................................................................................123
Table 9: Power Specifications ...........................................................................................................................................124
Table 10: Product Certifications .........................................................................................................................................124
Table 11: Pin Signals for 10 and 100 Mbps .......................................................................................................................125
Table 12: Pin Signals for 1000 Mbps .................................................................................................................................126
Table 13: RJ-45 Style Serial Console Port Pin Signals .....................................................................................................127
Table 14: Fiber Optic Port Specifications for the AT-StackOP/0.3 Module .......................................................................128
Table 15: Fiber Optic Port Specifications for the AT-StackOP/9.0 Transceiver ................................................................129
9
Tables
10
Preface
Note
This guide contains the installation instructions for the AT-x510DP-52GTX
Gigabit Ethernet switch. This preface contains the following sections:
“Document Conventions” on page 12
“Contacting Allied Telesis” on page 13
You can install AT-x510DP-52GTX switches as stand-alone devices
or in a stack configuration with Virtual Chassis Stacking
(VCStack™). This guide explains both options.
11
Preface
Note
Caution
Warning
Document Conventions
This document uses the following conventions:
Notes provide additional information.
Cautions inform you that performing or omitting a specific action
may result in equipment damage or loss of data.
Warnings inform you that performing or omitting a specific action
may result in bodily injury.
12
Contacting Allied Telesis
If you need assistance with this product, you may contact Allied Telesis
technical support by going to the Support & Services section of the Allied
Telesis web site at www.alliedtelesis.com/support. You can find links for
the following services on this page:
24/7 Online Support — Enter our interactive support center to
search for answers to your product questions in our knowledge
database, to check support tickets, to learn about RMAs, and to
contact Allied Telesis technical experts.
USA and EMEA phone support — Select the phone number that
best fits your location and customer type.
Hardware warranty information — Learn about Allied Telesis
warranties and register your product online.
Replacement Services — Submit a Return Merchandise
Authorization (RMA) request via our interactive support center.
x510DP-52GTX Installation Guide
Documentation — View the most recent installation and user
guides, software release notes, white papers, and data sheets for
your products.
Software Downloads — Download the latest software releases for
your managed products.
For sales or corporate information, go to www.alliedtelesis.com/
purchase and select your region.
13
Preface
14
Chapter 1
Note
Overview
This chapter contains the following sections:
“Features” on page 16
“Front and Rear Panels” on page 18
“Management Panel” on page 19
“10/100/1000Base-T Twisted Pair Ports” on page 20
“SFP+ Slots” on page 22
“Stacking SFP+ Slots” on page 23
“eco-friendly Button” on page 24
“LEDs” on page 25
“USB Port” on page 30
“Console Port” on page 31
“Power Supplies” on page 32
You can install AT-x510DP-52GTX switches as stand-alone devices
or in a stack configuration with Virtual Chassis Stacking (VCStack).
This guide explains both options.
15
Chapter 1: Overview
Note
Note
Note
Features
Here are the features of the AT-x510DP-52GTX switch:
10/100/1000
Mbps Twisted
Pair Ports
Here are the basic features of the 10/100/1000 Mbps twisted pair ports:
48 ports per switch
10Base-T, 100Base-TX, and 1000Base-T compliant
IEEE 802.3u Auto-Negotiation compliant
Auto-MDI/MDIX
100 meters (328 feet) maximum operating distance
IEEE 802.3x flow control in 10/100Base-TX full-duplex mode
IEEE 802.3x backpressure in 10/100Base-TX half-duplex mode
IEEE 803.3z 1000Base-T flow control
Jumbo frames up to 13KB
RJ-45 connectors
SFP+ Slots Here are the basic features of the four SFP+ slots on the switches:
Supports 10Gbps, 10GBase-SR/LR fiber optic transceivers
Supports 10Gbps AT-SP10TW direct connect twinax cables with
SFP+ transceiver-style connectors
Supports 1000Base-SX/LX SFP transceivers
Supports single-port BiDi 1000Base-LX SFP transceivers
Supports 1000Base-ZX SFP transceivers
The SFP+ slots do not support 100Mbps 100Base-FX transceivers.
SFP and SFP+ transceivers must be purchased separately. For a
list of supported transceivers, contact your Allied Telesis distributor
or reseller.
SFP+ slots 51 and 52 are initially configured as stacking slots for the
VCStack feature. If you intend to use the switch as a stand-alone
unit, you must disable the VCStack feature before using the slots
with standard SFP or SFP+ transceivers. See Chapter 5,
“Configuring the Switch for Stand-alone Operations” on page 77 for
instructions.
16
x510DP-52GTX Installation Guide
Power Supply
Modules
The AT-x510DP-52GTX switch has two rear slots for hot-swappable
power supplies. Power supply options are:
For AC power with back-to-front air flow, one or two AT-PWR100R
power supplies
For AC power with front-to-back air flow, one or two AT-PWR250
power supplies
For DC power with back-to-front air flow, one or two
AT-PWR250R-80 power supplies
Stacking Slots Two SFP+ slots can be used with special stacking transceivers to create a
VCStack of up to four switches that operate as a virtual switch. Here are
the basic features of the stacking slots on the AT-x510DP-52GTX switch:
Two stacking ports per switch
40Gbps stacking bandwidth
LEDs Here are the port LEDs:
Duplex mode and link/activity LEDs for the twisted pair ports
Link/activity LEDs for the SFP+ slots
Stack ID number LED
Installation
Options
MAC Address
Table
Management
Software and
Interfaces
Management
Methods
eco-friendly button turns off the LEDs to conserve electricity
Here are the installation options for the switches:
19-inch equipment rack - horizontal or vertical mounting
Desk or tabletop
Here are the basic features of the MAC address tables of the switches:
Storage capacity of 16,000 dynamic MAC address entries
Storage capacity of 256 static MAC address entries
Automatic learning and aging
Here are the management software and interfaces:
AlliedWare Plus Management Software
Command line interface
Web browser interface
Here are the methods for managing the switches:
Local management through the Console port
Remote Telnet and Secure Shell management
Remote HTTP and HTTPS web browser management
SNMPv1, v2c, and v3
17
Chapter 1: Overview
10/100/1000Base-T Ports
SFP+ Slots
Management
Panel
SFP+ or
Stacking Slots
S2/52
S1/51
50
49
CONSOLE
2662
x510DP-52GTX
SFP+
FDX HDX COL
1000 LINK ACT 10/100 LINK ACT
3517911131517192123
46810122 16 18 2014
22 24
27 2925 31 33 35 37 39 41 43 45 47
28 30 32 34 3626 40 42 4438
46 48
Power Supply Module
Bay 1
Power Supply Module
Bay 2
Front and Rear Panels
The front panel of the AT-x510DP-52GTX switch is shown in Figure 1.
AT-PWR100R
Figure 1. Front Panel of the AT-x510DP-52GTX Switch
Figure 2 on page 18 shows the back panel.
100-240VAC~ 2A MAX
DC OUT
FAULT
AT-PWR100R
100-240VAC~ 2A MAX
DC OUT
FAULT
Figure 2. Back Panel of the Switch
2001
18
Management Panel
Console
eco-friendly
Button
Switch
Port
ID LED
Management
USB Port
x510DP-52GTX Installation Guide
Figure 3 identifies the components in the management panel on the ATx510DP-52GTX switch.
Figure 3. AT-x510DP-52GTX Management Panel
19
Chapter 1: Overview
Note
Note
10/100/1000Base-T Twisted Pair Ports
The switches have 48 10/100/1000Base-T ports.
Speed The ports can operate at 10, 100, or 1000 Mbps. The speeds may be set
manually using the management software or automatically with AutoNegotiation (IEEE 802.3u), the default setting.
The ports must be set to Auto-Negotiation to function at 1000 Mbps
and are not compatible with devices that are not IEEE 802.3u
compliant.
Duplex Mode The twisted pair ports can operate in either half- or full-duplex mode. The
duplex mode of a port, like port speed, may be set manually using the
management software or automatically with Auto-Negotiation (IEEE
802.3u), the default setting.
Wiring
Configuration
The speed and duplex mode settings of a port may be set independently
of each other. For example, a port may be configured such that its speed
is set manually while its duplex mode is established through AutoNegotiation.
A switch port should not use Auto-Negotiation to set its duplex mode
if it is connected to a network device that does not support AutoNegotiation for 10 or 100 Mbps operation and has a fixed duplex
mode of full-duplex. Otherwise, a duplex-mode mismatch may occur
in which a switch port and a network device operate at different
duplex modes. The duplex modes of switch ports that are connected
to network devices that do not support Auto-Negotiation should be
set manually through the management software.
The wiring configuration of a port operating at 10 or 100 Mbps can be MDI
or MDI-X. The wiring configurations of a switch port and a network device
connected with straight-through twisted pair cabling have to be opposite,
such that one device is using MDI and the other MDI-X. For instance, a
switch port has to be set to MDI-X if it is connected to a network device set
to MDI.
You may set the wiring configurations of the ports manually or let the
switch configure them automatically with auto-MDI/MDI-X (IEEE 802.3abcompliant). This feature enables the switch to automatically negotiate with
network devices to establish their proper settings.
20
x510DP-52GTX Installation Guide
The MDI and MDI-X settings do not apply when ports are operating at
1000 Mbps.
Maximum
Distance
Cable
Requirements
The ports have a maximum operating distance of 100 meters (328 feet).
The cable requirements of the ports are given in Table 1.
Table 1. Twisted Pair Cable for the 10/100/1000Base-T Ports
Cable Type 10Mbps 100Mbps 1000Mbps
Standard TIA/EIA 568-Bcompliant Category 3 shielded
or unshielded cabling with 100
ohm impedance and a
frequency of 16 MHz.
Standard TIA/EIA 568-Acompliant Category 5 or TIA/
EIA 568-B-compliant Enhanced
Category 5 (Cat 5e) shielded or
unshielded cabling with 100
ohm impedance and a
frequency of 100 MHz.
Yes Yes No
Yes Yes Yes
Standard TIA/EIA 568-Bcompliant Category 6 or 6a
shielded cabling.
Yes Yes Yes
Port Pinouts Refer to Table 11 on page 125 and Table 12 on page 126 for the port
pinouts of the 10/100/1000Base-T twisted pair ports.
21
Chapter 1: Overview
Note
SFP+ Slots
The switches have four SFP+ slots that support the following types of SFP
1000Mbps and SFP+ 10Gbps transceivers:
1000Base-SX/LX SFP transceivers
Single-port BiDi 1000Base-LX SFP transceivers
1000Base-ZX SFP transceivers
10Gbps, 10GBase-SR/LR fiber optic transceivers
10Gbps AT-SP10TW direct connect twinax cables with SFP+
transceiver-style connectors
You may use the transceivers to connect switches to other network
devices over large distances, build high-speed backbone networks
between network devices, or connect high-speed devices, such as
servers, to your network.
The switches support a variety of short and long distance SFP and SFP+
modules. For a list of supported SFP modules, contact your Allied Telesis
representative or visit our web site.
SFP+ slots 51 and 52 are initially configured as stacking slots for the
VCStack feature. If you intend to use the switch as a stand-alone
unit, you must disable the VCStack feature before using the slots
with standard SFP or SFP+ transceivers. See Chapter 5,
“Configuring the Switch for Stand-alone Operations” on page 77 for
instructions.
22
Stacking SFP+ Slots
Note
Two of the four SFP+ slots on the front panel of the switch can be used
with stacking transceivers to create a VCStack of up to four switches. The
switches of a VCStack act as a single virtual unit. They synchronize their
actions so that switching operations, like spanning tree protocols, virtual
LANs, and static port trunks, span across all the units and ports. The two
main advantages of stacks are:
The slots for the stacking transceivers are SFP+ slots 51 and 52.
x510DP-52GTX Installation Guide
You can manage multiple units simultaneously, which can simplify
network management.
You have more flexibility in how you configure some of the
features. For instance, a static port trunk on a stand-alone switch
has to consist of ports from the same switch. In contrast, a static
trunk on a stack may consist of ports from different switches in the
same stack.
If you use the switch as a stand-alone device, you can use the slots
with regular SFP and SFP+ transceivers by disabling the VCStack
feature. See Chapter 5, “Configuring the Switch for Stand-alone
Operations” on page 77 for instructions.
You can stack any combination of the following switches, up to a total of
four switches:
AT-x510DP-52GTX
AT-x510-28GTX
AT-x510-52GTX
AT-x510-28GPX
AT-x510-52GPX
AT-x510-28GSX
23
Chapter 1: Overview
Note
eco-friendly Button
You may turn off the port LEDs to conserve electricity when you are not
monitoring the switch. The LEDs are toggled with the eco-friendly button
on the front panel of the switch or the ECOFRIENDLY LED and NO
ECOFRIENDLY LED commands in the Global Configuration mode of the
command line interface. The switch is said to be operating in a low power
mode when the LEDs are turned off.
Operating the switch in the low power mode with the LEDs turned off does
not interfere with the network operations of the device.
The Switch ID LED is always on, but it displays different information
depending on whether the LEDs are on or off. When the LEDs are on, the
ID LED displays the switches ID number. When the switch is operating in
the low power mode with the LEDs off, the LED indicates whether the
switch is a stand-alone unit or the master or member switch of a VCStack,
as detailed in Figure 8 on page 29.
Before checking or troubleshooting the network connections to the
ports on the switch, you should always check to be sure that the
LEDs are on by either pressing the eco-friendly button or issuing the
ECOFRIENDLY LED and NO ECOFRIENDLY LED commands in
the command line interface.
24
LEDs
Link/Activity
LED
Duplex Mode
LED
Duplex Mode
LED
Link/Activity
LED
x510DP-52GTX Installation Guide
Here are descriptions of the LEDs.
LEDs for the
Twisted Pair
Ports
Each twisted pair port has two LEDs that display link, activity and duplex
mode information. The LEDs are shown in Figure 4.
Figure 4. LEDs for the 10/100/1000Base-T Ports
The LEDs are described in Table 2 on page 25.
Table 2. LEDs on the 10/100/1000Base-T Ports
LED State Description
Link/
Activity
LED
Solid Green A port has established an 1000 Mbps link to
a network device.
Flashing
Green
Solid Amber A port has established a 10 or 100 Mbps
Flashing
Amber
Off A port has not established a link with
A port is transmitting or receiving data at
1000 Mbps.
link to a network device.
A port is transmitting or receiving data at 10
or 100 Mbps.
another network device or the LEDs are
turned off. To turn on the LEDs, use the
eco-friendly button.
25
Chapter 1: Overview
SFP+ Slot LEDs
Table 2. LEDs on the 10/100/1000Base-T Ports (Continued)
LED State Description
LEDs for the
SFP+ Slots
Duplex
Mode
LED
The LEDs for the SFP+ slots are located between the slots, as shown in
Figure 5. Each SFP+ slot has one LED. The left-hand LED is for the top
slot and the right-hand LED is for the bottom slot.
Green A port is operating in full duplex mode.
Amber A port is operating in half-duplex mode at 10
or 100 Mbps. (Half-duplex mode does not
apply to 1000 Mbps operation.)
Flashing
Amber
Collisions are occurring on a port operating
at 10 or 100 Mbps.
26
Figure 5. SFP+ Slot LEDs
The LEDs are described in Table 3.
x510DP-52GTX Installation Guide
Table 3. SFP+ Slot LEDs
LED State Description
Link/Activity Off The slot is empty, the SFP or SFP+
transceiver has not established a link to a
network device, or the LEDs are turned
off. To turn on the LEDs, use the ecofriendly button.
Solid green The SFP or SFP+ transceiver has
established a link at 1000 Mbps or 10
Gbps to a network device.
LEDs for the
Stacking Slots
Flashing
green
SFP+ slots 51 and 52 may be used as stacking slots to build a VCStack of
up to four switches. For background information, refer to Chapter 2,
“Virtual Chassis Stacking” on page 35. Table 4 defines the LED states
when the slots contain stacking transceivers.
Table 4. Stacking Slot LEDs
LED State Description
Link/Activity Off The slot is empty, the stacking transceiver
Solid green The stacking transceiver has established
The SFP+ transceiver is receiving or
transmitting packets to a network device
at 10 Gbps. (The LED does not flash for
activity at 1000 Mbps.).
has not established a link to a network
device, or the LEDs are turned off. To turn
on the LEDs, use the eco-friendly button.
a link at 10 Gbps to another switch in the
stack.
Flashing
green
The stacking transceiver is receiving or
transmitting packets.
Switch ID LED The Switch ID LED, shown in Figure 6 on page 28, displays the ID number
of the switch. A stand-alone switch has the ID number 0. Switches in a
VCStack have the numbers 1 to 4. Chapter 8, “Powering On the Stack” on
page 101 has the procedure for verifying and, if necessary, changing the
ID number of the switch.
27
Chapter 1: Overview
Switch
ID LED
The switch is booting up.
The switch has encountered a fault condition.
The switch is operating as a stand-alone unit, with the ID
number 0.
The switch has an ID number of 1 to 4 as part of a VCStack.
The dot in the lower right corner flashes when the switch
accesses USB memory.
Figure 6. Switch ID LED
The states of the LED when the switch is not operating in the low power
mode are shown in Figure 7.
The switch displays the letter “F” for fault on the ID LED if it encounters
one of the following problems:
A cooling fan has failed.
An unsupported power supply module has been installed.
One of the power supplies has failed.
The internal temperature of the switch has exceeded the normal
operating range and the switch may shut down.
28
Figure 7. Switch ID LED
x510DP-52GTX Installation Guide
Note
The switch is the master switch of a VCStack.
The switch is operating as a stand-alone unit.
The switch is a member switch of a VCStack.
You can use the SHOW SYSTEM ENVIRONMENT command in the
command line interface to identify the source of the problem.
The states of the LED when the switch is operating in the low power mode
are shown in Figure 8.
Figure 8. Switch ID LEDs in the Low Power Mode
29
Chapter 1: Overview
USB Port
The management panel has a USB port. You may use the port to store
configuration files on flash drives and to restore the files to switches
whose settings have been lost or corrupted, or to quickly configure
replacement units. You may also use the port and flash drives to update
the management firmware on the switches.
The port is USB2.0 compatible.
30
Console Port
Note
x510DP-52GTX Installation Guide
The Console port is used to establish a management session with the
switch to configure its features and parameter settings. This type of
management uses serial RS-232 and is commonly referred to as local or
out-of-band management because it is not conducted over your network.
To perform local management, you must be at the location of the switch
and must use the management cable included with the switch.
To establish a local management session with the switch, connect a
terminal or a personal computer with a terminal emulation program to the
Console port, which has an RJ-45 style (8P8C) connector, using the
provided management cable. The cable has RJ-45 RJ-style (8P8C) and
DB-9 (D-sub 9-pin) connectors.
The Console port is set to the following specifications:
Default baud rate: 9600 bps (Range is 9600 to 115200 bps)
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
These settings are for a DEC VT100 or ANSI terminal, or an
equivalent terminal emulation program.
31
Chapter 1: Overview
Warning
Warning
Note
Power Supplies
The AT-x510DP-52GTX switch has two rear slots for hot-swappable
power supplies.
The switch is supplied with a factory installed blank panel that covers both
power supply slots, and with a separate blank panel to use if you only
install one power supply.
Power supply options are:
For AC power with back-to-front air flow, one or two AT-PWR100R
power supplies
For AC power with front-to-back air flow, one or two AT-PWR250
power supplies
For DC power with back-to-front air flow, one or two
AT-PWR250R-80 power supplies
These power supplies are illustrated in Figure 9, Figure 10 and Figure 11
on page 33.
If you install two power supplies, they should be the same model.
Refer to “Technical Specifications” on page 123 for the input voltage
range.
For AC power supplies, the power cord is used as a disconnection
device. To de-energize equipment, disconnect the power cord.
E3
This unit might have more than one power cord. To reduce the risk
of electric shock, disconnect all power cords before servicing the
unit. E30
For AC power supplies, the switches are powered on or off by
connecting or disconnecting the power cords.
32
100-240VAC~ 2A MAX
100-240VAC~ 5A MAX
DC PWR
FAULT
AT-PWR250
2196
AT-PWR100R
Figure 9. AT-PWR100R AC Power Supply
x510DP-52GTX Installation Guide
DC OUT
FAULT
2196
Figure 10. AT-PWR250 AC Power Supply
AT-PWR250R
40-60VDC
6A
OUTPUT POWER
FAULT
Figure 11. AT-PWR250R DC Power Supply
FOR CENTRALIZED DC POWER
CONNECTION, INS TALL ONLY IN A
RESTRICTED AREA.
2197
33
Chapter 1: Overview
34
Chapter 2
Virtual Chassis Stacking
The sections in this chapter are:
“Overview” on page 36
“Stacking Slots” on page 37
“Stacking Transceivers” on page 38
“Stacking Port Topologies” on page 40
“Master and Member Switches” on page 44
“Specifying Ports in the Command Line Interface” on page 46
For more information on the VCStack feature, refer to the Stacking
Introduction and Stacking Commands chapters in the Software Reference:
AlliedWare Plus Operating System for x510 Series.
35
Chapter 2: Virtual Chassis Stacking
Overview
Virtual Chassis Stacking (VCStack) allows you to connect up to four
switches to form a virtual switch in which the devices function as a single
networking unit. The benefits of VCStack are:
Simplifies management - You can manage the devices of the stack
as a single unit, rather than individually. Your local and remote
management sessions automatically give you management
access to all the devices.
Reduces IP addresses - A stack requires only one IP address for
remote management access, thereby reducing the number of IP
addresses you have to assign to network devices, The one
address gives you management access to all the units.
Adds feature flexibility and resiliency - A stack gives you more
flexibility in how you can configure some features. For instance,
you can create port aggregators of ports from different switches in
the stack, rather than from only one switch. If you distribute the
ports of an aggregator across two or more switches in a stack, you
increase its resiliency because the aggregator will continue to
function, though at a reduced bandwidth, if one of the switches
stops functioning.
Reduces protocol requirements - Creating a stack might eliminate
your need to configure some protocols, such as the Virtual Router
Redundancy Protocol and Spanning Tree Protocol.
You can stack any combination of the following switches, up to a total of
four switches:
AT-x510DP-52GTX
AT-x510-28GTX
AT-x510-52GTX
AT-x510-28GPX
AT-x510-52GPX
AT-x510-28GSX
36
Stacking Slots
Note
x510DP-52GTX Installation Guide
The AT-x510DP-52GTX switches come with two stacking slots. The slots
are the last two SFP+ slots on the switches and are labeled S1/51 and S2/
52.
The slots have two functions. You may use them with the VCStack feature
to build a stack of switches or, by disabling the VCStack feature, you may
use them with regular SFP or SFP+ transceivers as additional networking
slots.
The names of the slots depend on the status of the VCStack feature on the
switch. The management software refers to the slots as “S1” and “S2.”
when the VCStack feature is enabled and the slots are used with the
special stacking transceivers to create a stack.
When you disable the VCStack feature to use the slots with regular SFP or
SFP+ transceivers on a stand-alone switch, the slots are referred to as
slots 51 and 52. See Chapter 5, “Configuring the Switch for Stand-alone
Operations” on page 57 for instructions for disabling VCStack.
When VCStack is enabled on the switch, the stacking slots only
work with the stacking transceivers in Table 5 on page 38. If you
install regular SFP or SFP+ transceivers in the stacking slots when
stacking is activated, the management software disables them and
enters an error message in the buffered log.
37
Chapter 2: Virtual Chassis Stacking
AT-StackXS/1.0
AT-StackOP/0.3
AT-StackOP/9.0
Stacking Transceivers
You connect the switches of the VCStack with the stacking transceivers
listed in Table 5 and shown in Figure 12.
Table 5. Stacking Transceivers
Stacking
Transceiver Model
AT-StackXS/1.0 Twinax cable 1 meter
AT-StackOP/0.3 62.5/125 µm multi-
AT-StackOP/9.0 9/125 µm single-
Cable Type Operating Distance
33 meters (108 feet)
mode fiber optic
cable
50/125 µm multimode fiber optic
cable
mode fiber optic
cable
300 meters (984 feet)
9 kilometers
38
Figure 12. Stacking Transceivers
With its two SFP+ transceiver-style connectors and one meter of twinax
cable, the AT-StackXS/1.0 transceiver is appropriate in situations where
the switches are in the same equipment rack or on the same table.
The fiber optic transceivers are used to build stacks across large
distances.
x510DP-52GTX Installation Guide
Here are the transceiver guidelines:
The stacking transceivers may only be used in the stacking slots
and only with the VCStack feature. You may not use the
transceivers as regular networking ports.
The AT-StackOP/0.3 and AT-StackOP/9.0 transceivers must be
connected to other AT-StackOP/0.3 and AT-StackOP/9.0
transceivers. The transceivers do not work with other types of
network devices.
You may use different types of transceivers to connect the
switches of a stack and so build stacks of switches that are at
various distances from each other.
39
Chapter 2: Virtual Chassis Stacking
Caution
2694
S2/28
S1/27
26
25
CONSOLE
SFP+
S2/28
S1/27
26
25
CONSOLE
SFP+
Stacking Port Topologies
The switches of a stack are connected with the S1 and S2 ports and the
stacking transceivers shown in Figure 12 on page 38.
There are two wiring configurations. The first topology is called the linear
topology. In this topology the switches are connected with a single
pathway. A stacking transceiver in one switch is connected to a stacking
transceiver in the next switch, which is connected to the next switch, and
so on. The connections must crossover to different stacking slots on the
switches. The stacking transceiver in the S1 slot in one switch must
connect to the stacking transceiver in the S2 slot in the next switch.
Figure 13 is an example of a stack of two switches in the linear topology.
The transceiver in the S1 slot on the top switch is connected to the
transceiver in the S2 slot on the bottom switch.
40
Figure 13. Stack of Two Switches in the Linear Topology
The stack will not function if the connections to the S1 and S2 slots
do not crossover on the switches. The switches will not form a stack
and instead operate as stand-alone devices.
x510DP-52GTX Installation Guide
S2/28
S1/27
26
25
CONSOLE
SFP+
S2/28
S1/27
26
25
CONSOLE
SFP+
S2/28
S1/27
26
25
CONSOLE
SFP+
S2/28
S1/27
26
25
CONSOLE
SFP+
The stack in Figure 14 on page 41 has four switches in the linear topology.
Figure 14. Stack of Four Switches in the Linear Topology
The second topology is called the ring topology. It is similar to the linear
topology, except that the unused stacking ports on the end switches of the
stack are connected to form a physical loop. This topology is more resilient
than the linear topology because there are two pathways through the
stack. If one pathway fails, the switches can maintain communications
through the alternate pathway. The example in Figure 15 on page 42
shows a ring topology of two switches.
41
Chapter 2: Virtual Chassis Stacking
S2/28
S1/27
26
25
CONSOLE
SFP+
S2/28
S1/27
26
25
CONSOLE
SFP+
2696
Figure 15. Stack of Two Switches in the Ring Topology
Figure 16 on page 43 is an example of a stack of four switches in the ring
topology.
42
x510DP-52GTX Installation Guide
S2/28
S1/27
26
25
CONSOLE
SFP+
S2/28
S1/27
26
25
CONSOLE
SFP+
S2/28
S1/27
26
25
CONSOLE
SFP+
S2/28
S1/27
26
25
CONSOLE
SFP+
2697
Figure 16. Stack of Four Switches in the Ring Topology
The topologies are the same in terms of network speed and performance.
However, the ring topology is the recommended wiring configuration
because of the secondary path through the stacking ports. The two
pathways protect the switches of the stack against the loss of
communications due to a failure of a stacking port, cable, or switch.
The examples in the previous figures showed the twinax AT-StackXS/1.0
stacking transceiver. But the same rules apply to the fiber optic ATStackOP/0.3 and AT-StackOP/9.0 stacking transceivers. A fiber optic
transceiver in the S1 slot must crossover to a fiber optic transceiver in the
S2 slot of another switch.
43
Chapter 2: Virtual Chassis Stacking
Master and Member Switches
The stack has one master switch. The functions of the master switch
include:
Coordinating and monitoring stack operations.
Verifying that the switches are using the same version of
management software. It automatically downloads its management
software over the stacking cables to switches with different
software versions.
Verifying that the switches have different ID numbers. It
automatically assigns new ID numbers to resolve situations where
two or more switches have the same ID number.
Verifying that the stacking transceivers that connect the switches
together are cabled correctly.
The other switches are called member switches. There can be up to three
member switches in addition to the master switch. A member switch can
automatically transition to the master role if the current master switch is
removed from the stack or powered off. This ensures continued operations
of the stack even if the master switch stops operating.
Selection of the
Master Switch
The devices compare the following numbers to choose the master switch
when the stack is reset or powered on:
Stack priority numbers
MAC addresses
The stack priority number is an adjustable value of 0 to 255, where the
lower the number, the higher the priority. Typically, the switch with the
lowest priority number (highest priority) becomes the master switch of a
stack. The default priority value is 128.
If the switches have the same priority values, the selection of the master
switch is based on their MAC addresses. As with the priority value, the
lower the MAC address, the higher the priority. The switch with the lowest
MAC address becomes the master switch.
If you power on the stack for the first time without adjusting the priority
values, the master switch is selected based on the MAC addresses if the
units are powered on simultaneously. If you power on the switches one at
a time, the master switch is the first switch to be powered on. This is
explained in Chapter 8, “Powering On the Stack” on page 101.
After the stack is established and operating, you may, if you choose,
change the priority settings on the individual units and so control which
switch will be the master switch after subsequent power cycles and resets.
44
x510DP-52GTX Installation Guide
Caution
ID Numbers Each switch must be assigned an ID number. The range is 1 to 4 and the
default is 1. The ID numbers are displayed on the ID LEDs on the front
panels of the units. You may assign the numbers yourself or you can let
the master switch assign the numbers automatically, as explained in
Chapter 8, “Powering On the Stack” on page 101.
You use the ID numbers to identify the individual ports and switches when
you configure the devices with the commands in the management
software. For further information, refer to “Specifying Ports in the
Command Line Interface” on page 46.
The ID numbers are also used to identify the parameter settings that are
stored in the configuration file. When the stack is reset or power cycled,
the ID numbers identify the devices to which the parameter settings
belong.
You should not change the ID numbers of the switches after you
have started to configure the parameter settings. Otherwise, the
parameter settings might be applied to the wrong devices when you
reset or power cycle the stack.
The switches do not use the ID numbers to select the master switch. The
selection of the master switch is typically based on the priority numbers
and MAC addresses, as previously explained.
45
Chapter 2: Virtual Chassis Stacking
port1.0
.n
Module ID
Port Number
Stack ID
Specifying Ports in the Command Line Interface
The command line interface in the management software on the switch
has a parameter that you use to specify the individual ports. The
parameter is the PORT parameter and Figure 17 shows its format.
Figure 17. PORT Parameter in the Command Line Interface
The first number is the switch’s ID number. The ID numbers of switches in
a stack are displayed on their ID LEDs. You can also view the ID numbers
with the SHOW STACK command in the command line interface.
The module ID value is used with multi-module products. This value does
not apply to the x510 Series switches and should always be 0.
The third value is a port number on the switch. You may specify only one
port number in a PORT parameter, but you may specify more than one
PORT parameter in many of the commands where the parameter is
supported.
Here is an example of the PORT parameter. It uses the INTERFACE
command to enter the Port Interface mode for ports 15 and 17 on the
switch with ID 2:
awplus> enable
awplus# configure terminal
awplus(config)# interface port2.0.15,port2.0.17
For instructions on the command line interface and the PORT parameter,
refer to the Software Reference: AlliedWare Plus Operating System for
x510 Series.
46
Chapter 3
Beginning the Installation
The chapter contains the following sections:
“Reviewing Safety Precautions” on page 48
“Choosing a Site for the Switches” on page 52
“Planning a Stack” on page 53
“Unpacking the Switch” on page 55
47
Chapter 3: Beginning the Installation
Note
Warning
Warning
Warning
Warning
Warning
Warning
Reviewing Safety Precautions
Please review the following safety precautions before beginning the
installation procedure.
Safety statements that have the symbol are translated into
multiple languages in the Translated Safety Messages document at
www.alliedtelesis.com/support/documentation.
Class 1 Laser product. L1
Do not stare into the laser beam. L2
Do not look directly at the fiber optic cable ends or inspect the cable
ends with an optical lens. L6
Class 1 LED product. L3
To prevent electric shock, do not remove the cover. No userserviceable parts inside. This unit contains hazardous voltages and
should only be opened by a trained and qualified technician. To
avoid the possibility of electric shock, disconnect electric power to
the product before connecting or disconnecting the LAN cables.
E1
Do not work on equipment or cables during periods of lightning
activity. E2
48
x510 Series Installation Guide for Virtual Chassis Stacking
Warning
Warning
Note
Caution
Warning
Note
Warning
Caution
For AC PSUs, power cord is used as a disconnection device. To deenergize equipment, disconnect the power cord. E3
Class I Equipment. This equipment must be earthed. The power
plug must be connected to a properly wired earth ground socket
outlet. An improperly wired socket outlet could place hazardous
voltages on accessible metal parts. E4
Pluggable Equipment. The socket outlet shall be installed near the
equipment and shall be easily accessible. E5
Air vents must not be blocked and must have free access to the
room ambient air for cooling. E6
Operating Temperature. This product is designed for a maximum
ambient temperature of 50 degrees C. E57
All Countries: Install product in accordance with local and National
Electrical Codes. E8
Only trained and qualified personnel are allowed to install or replace
this equipment. E14
Circuit Overloading: Consideration should be given to the
connection of the equipment to the supply circuit and the effect that
overloading of circuits might have on overcurrent protection and
supply wiring. Appropriate consideration of equipment nameplate
ratings should be used when addressing this concern. E21
49
Chapter 3: Beginning the Installation
Caution
Warning
Note
Warning
Note
Caution
Risk of explosion if battery is replaced by an incorrect type. Replace
only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
Attention: Le remplacement de la batterie par une batterie de type
incorrect peut provoquer un danger d’explosion. La remplacer
uniquement par une batterie du même type ou de type équivalent
recommandée par le constructeur. Les batteries doivent être
éliminées conformément aux instructions du constructeur. E22
Mounting of the equipment in the rack should be such that a
hazardous condition is not created due to uneven mechanical
loading. E25
Use dedicated power circuits or power conditioners to supply
reliable electrical power to the device. E27
This unit might have more than one power cord. To reduce the risk
of electric shock, disconnect all power cords before servicing the
unit. E30
If installed in a closed or multi-unit rack assembly, the operating
ambient temperature of the rack environment may be greater than
the room ambient temperature. Therefore, consideration should be
given to installing the equipment in an environment compatible with
the manufacturer’s maximum rated ambient temperature (Tmra).
E35
Installation of the equipment in a rack should be such that the
amount of air flow required for safe operation of the equipment is not
compromised. E36
50
x510 Series Installation Guide for Virtual Chassis Stacking
Warning
Caution
Warning
Reliable earthing of rack-mounted equipment should be maintained.
Particular attention should be given to supply connections other than
direct connections to the branch circuits (e.g., use of power strips).
E37
The unit does not contain serviceable components. Please return
damaged units for servicing. E42
When you remove an SFP module from this product, the case
temperature of the SFP may exceed 40° C (158° F). Exercise
caution when handling with unprotected hands. E43
51
Chapter 3: Beginning the Installation
Warning
Choosing a Site for the Switches
Observe these requirements when planning the installation of the switches
of a stack.
If you plan to install the switches in an equipment rack, check to be
sure that the rack is safely secured so that it will not tip over.
Devices in a rack should be installed starting at the bottom, with
the heavier devices near the bottom of the rack.
If you plan to install the switches on a table, check to be sure that
the table is level and stable.
The power outlet should be located near the switches and be
easily accessible.
The site should allow for easy access to the ports on the front of
the switches, so that you can easily connect and disconnect
cables, and view the port LEDs.
The site should allow for adequate air flow around the units and
through the cooling vents on the front and rear panels. If you have
AT-PWR100R or AT-PWR250R-DC power supplies, the ventilation
direction is from back to front, with air coming out of the front vent.
If you have AT-PWR250 power supplies, the ventilation direction is
from front to back, with the fan on the back panel drawing the air
out of the unit.
The site should not expose the switches to moisture or water.
The site should be a dust-free environment.
The site should include dedicated power circuits or power
conditioners to supply reliable electrical power to the network
devices.
Do not install the switches in a wiring or utility box because they
will overheat and fail from inadequate airflow.
Switches should not be stacked on top of one another on a table or
desktop because that could present a personal safety hazard if you
need to move or replace switches.
52
Planning a Stack
x510 Series Installation Guide for Virtual Chassis Stacking
Here are the guidelines to planning a stack:
A stack can have up to four switches.
A stack can have different models of x510 Series switches. It
cannot contain other switches, such as IX5 or x610 Series
switches.
Any of the switches in the stack can be the master switch.
Switches connected with AT-StackXS/1.0 stacking cables should
be installed in a standard 19-inch equipment rack and not more
than one meter apart, the length of the stacking cable. The end
switches cannot be more than one meter apart if you want to
create the ring topology, shown in Figure 15 on page 42 and Figure
16 on page 43.
You may use the AT-StackOP/0.3 and AT-StackOP/9.0
transceivers to build stacks of switches that are up to 300 meters
and 9 kilometers apart, respectively.
The wiring topology of the stack may be either linear or ring. Both
topologies offer the same in terms of speed, but the ring topology
adds wiring redundancy.
You can use combinations of AT-StackXS/1.0, AT-StackOP/0.3,
and AT-StackOP/9.0 cables when the individual switches of the
stack are at various distances from each other.
The switches do not need any additional software for stacking.
However, they do need stacking transceivers.
You may not install a networking device, such as a media
converter or Ethernet switch, between two fiber optic stacking
transceivers.
All switches must have the same licenses of optional features. If
you install an optional feature on one switch, you must install it on
all switches before assembling the stack.
The AT-StackOP/9.0 transceiver has a maximum operating
distance of 9 kilometers and requires 9/125 µm single-mode fiber
optic cable. The operating specifications of the transceiver are
listed in Table 15 on page 129.
Table 6 on page 54 lists the maximum distances of the AT-
StackOP/0.3 transceiver. The operating specifications of the
transceiver are listed in Table 14 on page 128.
53
Chapter 3: Beginning the Installation
Table 6. Operating Distances of the AT-StackOP/0.3 Transceiver
Minimum Modal
Fiber Type
Bandwidth @ 850
Operating Range
nm (MHz*km)
62.5/125 µm multimode fiber optic
cable
50/125 µm multimode fiber optic
cable
160 2 to 26 meters
(7 to 85 feet)
200 2 to 33 meters
(7 to 108 feet)
400 2 to 66 meters
(7 to 217 feet)
500 2 to 82 meters
(7 to 269 feet)
2000 2 to 300 meters
(7 to 984 feet)
54
Unpacking the Switch
Note
Two rack mounting brackets
One 2 m (6.6 ft) local management cable with
RJ-45 (8P8C) and DB-9 (D-sub 9-pin)
connectors.
2047
Twelve rack mounting bracket
screws
AT-PNL250
One AT-PLN250 blank panel for
covering an empty power supply bay
Figure 18 lists the items that come with the switch. If any item is missing or
damaged, contact your Allied Telesis sales representative for assistance.
x510 Series Installation Guide for Virtual Chassis Stacking
1947
Figure 18. Components of the switch
You should retain the original packaging material in the event you
need to return the unit to Allied Telesis.
After checking the contents of the shipping containers, go to Chapter 4,
“Installing the Switch and its Power Supplies” on page 57
55
Chapter 3: Beginning the Installation
56
Chapter 4
Installing the Switch and its Power Supplies
The procedures in this chapter are:
“Installing the Power Cord Retaining Clip” on page 58
“Installing Power Supply Modules” on page 59
“Installing the Switches on a Table or Desktop” on page 63
“Installing the Switch in an Equipment Rack” on page 64
“Connecting AC Power to a Power Supply Module” on page 67
“Power Wiring to a DC AT-PWR250R-80 Power Supply Module” on
page 69
“Starting a Local Management Session” on page 73
“Monitoring the Initialization Processes” on page 74
57
Chapter 4: Installing the Switch and its Power Supplies
100-240VAC
~
Installing the Power Cord Retaining Clip
This section applies to AC power supply modules.
Perform the following procedure to install the power cord retaining clip on
each power supply module:
1. Locate the power cord retaining clip, shown in Figure 19.
Figure 19. Power Cord Retaining Clip
2. Install the clip on the AC power connector on the power supply
module. With the ‘u’ of the clip facing down, press the sides of the clip
toward the center and insert the short ends into the holes in the
retaining bracket, as shown in Figure 20.
58
Figure 20. Inserting the Retaining Clip into the Retaining Bracket
You are now ready to install the switches, as explained in the next
procedures.
Installing Power Supply Modules
Note
Overview The AT-x510DP-52GTX switch has two rear slots for hot-swappable
power supplies.
The switch is supplied with a factory installed blank panel that covers both
power supply slots, and with a separate blank panel to use if you only
install one power supply.
Power supply options are:
For AC power with back-to-front air flow, one or two AT-PWR100R
power supply modules - see Figure 9 on page 33
For AC power with front-to-back air flow, one or two AT-PWR250
power supply modules - see Figure 10 on page 33
For DC power with back-to-front air flow, one or two
AT-PWR250R-80 power supply modules - see Figure 11 on page
33
x510DP-52GTX Installation Guide
Installing a
Power Supply
The installation procedure is identical for each power supply.
To install a power supply, perform the following procedure:
1. Remove the module from the shipping package.
Store the packaging material in a safe location. You must use the
original shipping material if you need to return the unit to Allied
Telesis.
59
Chapter 4: Installing the Switch and its Power Supplies
Caution
2. Remove the blank panel from the power supply slots on the rear panel
of the switch by unscrewing it, as shown in the following figure.
Figure 21. Removing the rear panel
3. Align the edges of the power supply module with the guides in the slot
and carefully slide the module into the chassis until it is flush with the
rear panel of the chassis, as shown below. Light pressure may be
needed to seat the module on the connector on the rear panel of the
chassis.
Do not force the power supply module into place. Doing so may
damage the connector pins on the backplane inside the chassis. If
there is resistance, remove the module and reinsert it after verifying
that the edges of the card are properly aligned in the guides in the
chassis’ module slot.
60
x510DP-52GTX Installation Guide
2268
DC
OUT
F
AUL
T
AT-PWR100R
1
0
0
-240
VAC~ 2A
MAX
2269
DC
OUT
F
AULT
AT-PWR100R
1
0
0
-24
0
V
A
C~ 2A MAX
Figure 22. Installing the AT-PWR100R AC Power Supply Module
4. Secure the power supply module to the chassis by tightening the two
captive screws with a cross-head screwdriver, as shown below.
Figure 23. Securing the AT-PWR100R Power Supply Module
61
Chapter 4: Installing the Switch and its Power Supplies
DC
OUT
F
AULT
AT-PWR100R
1
00-240VAC~ 2A MAX
5. If you are going to operate the switch with a single power supply
module, install the supplied blank panel over the second power supply
module bay, as shown in the following figure. This is necessary for
correct airflow.
Figure 24. Installing the Blank Panel on the Power Supply Slot
6. If you are installing an AC power supply module, see “Connecting AC
Power to a Power Supply Module” on page 67 for the power cord
installation.
7. If you are installing a DC power supply module, see “Power Wiring to a
DC AT-PWR250R-80 Power Supply Module” on page 69 for the DC
power wiring installation.
62
Installing the Switches on a Table or Desktop
Warning
You may install the switches on a table or desktop. Here are the guidelines
to selecting a site:
The table should be level and stable.
The power outlets should be located near the switches and be
easily accessible.
The site should allow for easy access to the ports on the front of
the switches, so that you can easily connect and disconnect
cables, and view the port LEDs.
The site should allow for adequate air flow around the units and
through the cooling vents on the front and rear panels. If you have
AT-PWR100R or AT-PWR250R-DC power supplies, the ventilation
direction is from back to front, with air coming out of the front vent.
If you have AT-PWR250 power supplies, the ventilation direction is
from front to back, with the fan on the back panel drawing the air
out of the unit.
x510DP-52GTX Installation Guide
The site should not expose the switches to moisture or water.
The site should be a dust-free environment.
The site should include dedicated power circuits or power
conditioners to supply reliable electrical power to the network
devices.
The rubber feet on the bottom of the switches should be left on for
table or desktop installation.
Do not stack switches on top of one another on a table or desktop
because that could present a personal safety hazard if you need to
move or replace switches.
After placing the switches on the table or desktop, if you are installing a
VCStack, go to Chapter 6, “Verifying the Status of VCStack and Activating
VCStack” on page 85 to verify that VCStack is activated on the units.
63
Chapter 4: Installing the Switch and its Power Supplies
Caution
2668
S2/52
S1/51
50
49
CONSOLE
x510DP-52GTX
SFP+
FDX HDX COL
1000 LINK ACT 10/100 LINK ACT
351791113151719
21 23
46810122 16 18 2014
22 24
27 2925 31 33 35 37 39 41 43 45 47
28 30 32 34 3626 40 42 4438
46 48
2669
x510DP-52GTX
3
5179
1
1
46
810
1
22
Installing the Switch in an Equipment Rack
This procedure requires the following items:
Twelve bracket screws (included with the switch)
Two equipment rack brackets (included with the switch)
Flat-head screwdriver (not provided)
Cross-head screwdriver (not provided)
Four standard equipment rack screws (not provided)
Installation guidelines may be found in “Choosing a Site for the Switches”
on page 52. Here is the procedure for installing the switch horizontally or
vertically in a 19-inch equipment rack.
The chassis may be heavy and awkward to lift. Allied Telesis
recommends that you get assistance when mounting the chassis in
an equipment rack. E28
1. Place the unit upside down on a level, secure surface.
Figure 25. Turning the Switch Upside Down
2. Using a flat-head screwdriver, pry the rubber feet from the bottom of
the switch, as shown in Figure 26.
64
Figure 26. Removing the Rubber Feet
x510DP-52GTX Installation Guide
2672
S
2
/
2
8
S
1
/
2
7
2
6
25
C
ON
S
O
L
E
S
F
P
+
x510DP-52GTX
F
D
X
H
D
X
C
O
L
1
0
0
0
L
I
N
K
A
C
T
1
0
/
1
0
0
L
I
N
K
A
CT
3
51
7
9
11 1
31
5
1
71
9
21
2
3
4
6
8
1
01
2
2
16
18
20
1
4
2
2
24
2
7
2
9
2
5
31
3
3
3
5
37
39 4
1
4
3
45
47
2
8
30
3
2
3
4
36
2
6
40
4
2
4
4
38
46
48
S
2/28
S1/2
7
2
6
25
C
O
N
SO
L
E
S
F
P+
x510DP-52GTX
F
DX
HDX
CO
L
1
0
0
0
L
INK
A
C
T
1
0
/
1
0
0
L
I
N
K
A
CT
3
5179111
3
15
17
19 21
2
3
4
68
10 1
2
2
16
18
20
1
4
22
24
27 29
2
5
31
3
3
3
5
3
7
3
941
43
45
47
2
8
30
3
2
34
3
626
4
0
4
2
4
4
3
8
4
6
48
S2
/28
S1
/
27
2
6
25
C
ON
S
OL
E
S
FP+
x510DP-52GTX
F
D
X
H
DX
C
O
L
1
0
0
0
L
IN
K
A
CT
1
0
/
1
0
0
L
I
NK
A
C
T
3
5
17
9
1
1
13
15
17
19
2
1
2
3
46810
12
2
16
1
8
2
0
14
22 2
4
2
729
2
5
31
3
3
3
5
37
39 41
4
3
45
47
2
8
30
32 3
4
3
6
26
4
0
4
2
4
4
38
46
4
8
2672
S2/2
8
S1/2
7
2
6
25
C
ON
SO
L
E
S
FP+
x510DP-52GTX
F
D
X
H
D
X
CO
L
1
0
0
0
L
INK
A
CT
1
0
/
1
0
0
L
I
N
K
A
CT
3
51791
1131
5
17
19
2
1
23
4
6810 122
1
6
18
20
14
22
2
4
27 29
2
5
31
3
33
537
39 41 43
45
47
2
8
30
32 34
3626
40
4
2
4
4
38
46
48
3. Turn the switch over.
4. Attach the two rack mount brackets to the sides of the switch using the
bracket screws included with the unit. Figure 27 on page 65 illustrates
the four possible bracket positions.
Figure 27. Attaching the Equipment Rack Brackets
65
Chapter 4: Installing the Switch and its Power Supplies
5. While another person holds the switch in the equipment rack, secure it
using standard equipment rack screws (not provided), as shown in
Figure 28 for horizontal mounting and Figure 29 for vertical mounting.
Figure 28. Mounting the Switch Horizontally in an Equipment Rack
179
35
x510DP-52GTX
2 16
4
6
810
1
1
1
31517
19 2
1
2
1
14
23
531
1
8
2
7292
20
10
0
0
L
I
N
K
A
2
CT
2
10
/
100
LI
N
24
K
AC
3
T
3
6
3
5
2
83
FD
X
3
7
H
DX
03
COL
3
94
2
14
34
3
3
62
45
38
47
4
0
2
5
42
S
F
P
+
S
1/27
4
4
46
48
2
6
CO
N
S
O
L
S2
E
/
2
8
2674
x510DP-52GTX
3517911131517192123
4 6 8 10 122 16 18 2014
1000 LINK ACT 10/100 LINK ACT
22 24
FDX HDX COL
27 2925 31 33 35 37 39 41 43 45 47
28 30 32 34 3626 40 42 4438
46 48
50
49
SFP+
S2/52
S1/51
CONSOLE
Figure 29. Mounting the Switch Vertically in an Equipment Rack
6. If required, repeat this procedure to install the remaining switches in
the stack.
66
7. Apply power to the switch or switches, as described in the following
procedures.
Connecting AC Power to a Power Supply Module
100-240VAC
~
100-240VAC
~
To power on a switch with one or two AC Power Supply Modules, perform
the following procedure:
1. Position the power cord retaining clip in the up position, as shown in
Figure 30.
Figure 30. Power Cord Retaining Clip in the Up Position
x510DP-52GTX Installation Guide
2. Plug the power cord into the AC power connector on the rear panel of
the unit, as shown in Figure 31. Lower the power cord retaining clip to
secure the power cord to the unit.
Warning: Power cord is used as a disconnection device. To deenergize equipment, disconnect the power cord.
E3
Figure 31. Connecting the AC Power Cord
67
Chapter 4: Installing the Switch and its Power Supplies
Warning
3. Connect the other end of the power cord to an appropriate AC power
outlet. For power specifications for the switch, refer to “Power
Specifications” on page 124.
This unit might have more than one power supply. To reduce the risk
of electric shock, disconnect all power cords before servicing the
unit. E30
4. Repeat the above procedure for the second PSU, if necessary.
5. Start a local management session on the unit by performing the
procedure in “Starting a Local Management Session” on page 73.
68
x510DP-52GTX Installation Guide
Warning
Warning
Note
Warning
Power Wiring to a DC AT-PWR250R-80 Power Supply Module
This section describes how to power on a switch with a DC
AT-PWR250R-80 Power Supply Module, and essential safety information.
As a safety precaution, install a double-pole circuit breaker with a
maximum value of 20 Amps and a minimum value of 15 Amps
between the equipment and the DC power source.
Always connect the wires to the LAN equipment first before you
connect the wires to the circuit breaker. Do not work with HOT feeds
to avoid the danger of physical injury from electrical shock. Always
be sure that the circuit breaker is in the OFF position before
connecting the wires to the breaker. E54
For centralized DC power connection, install only in a restricted
access area. E23
A tray cable is required to connect the power source if the unit is
powered by centralized DC power. The tray cable must be a UL
listed Type TC tray cable and rated at 600 V and 90 degrees C, with
three conductors, minimum 14 AWG. E24
This equipment is designed to permit the connection of the earthed
conductor of the DC supply circuit to the earthing conductor at the
equipment. If this connection is made, all of the following conditions
must be met:
This equipment shall be connected directly to the DC supply
system earthing electrode conductor or to a bonding jumper from
an earthing terminal bar or bus to which the DC supply system
earthing electrode conductor is connected.
This equipment shall be located in the same immediate area
(such as adjacent cabinets) as any other equipment that has a
connection between the earthed conductor of the same DC
supply circuit and the earthing conductor, and also the point of
earthing of the DC system. The DC system shall not be earthed
elsewhere.
The DC supply source shall be located within the same premises
69
Chapter 4: Installing the Switch and its Power Supplies
Warning
2205
A
A
AT-PWR250R
DC OUT
FAULT
+
-
6A
40-60VDC
FOR CENTRALIZED DC POWER
CONNECTION, INSTALL ONLY IN A
ON
OFF
+48 VDC Positive Ground -48 VDC Negative
TerminalTerminalTerminal
Switching or disconnecting devices shall not be in the earthed
Enough wiring space is required to allow the conductors to be
introduced and connected easily. E56
To power on a switch with a DC AT-PWR250R-80 Power Supply Module,
review the essential safety information above and perform the following
procedure:
1. Power off the DC circuit to be used for the chassis.
2. Verify that the On/Off switch on the DC AT-PWR250R-80 Module is in
the Off position.
as this equipment.
circuit conductor between the DC source and the point of
connection of the earthing electrode conductor. E55
3. Use the legend above the terminal block to identify the terminals. The
terminals are positive, power supply ground and negative, from left
to right, as shown in Figure 32 on page 70.
Figure 32. DC Terminal Block on the DC AT-PWR250R-80 Power Supply
Module
70
x510DP-52GTX Installation Guide
Warning
Warning
4. With a 14-gauge wire-stripping tool, strip the three wires in the tray
cable coming from the DC input power source to 8mm ± 1mm (0.31 in.,
± 0.039 in.), as shown in Figure 33 on page 71.
Do not strip more than the recommended amount of wire. Stripping
more than the recommended amount can create a safety hazard by
leaving exposed wire on the terminal block after installation. E10
8mm ±1mm
(0.31in. ±0.039in.)
Figure 33. Stripped Wire
5. Insert the power supply ground wire into the middle connector of the
DC terminal and tighten the connection with a flathead screwdriver, as
shown in Figure 34 on page 71.
When installing this equipment, always ensure that the power supply
ground connection is installed first and disconnected last. E11
40-60VDC
6A
AT-PWR250R
OUTPUT P
F
A
U
O
W
ER
LT
FOR CENTRALIZED DC POWER
CONNECTION, INS TALL ON LY IN A
RESTRICTED AREA.
2269
Figure 34. Inserting Wires into a DC Terminal Block
71
Chapter 4: Installing the Switch and its Power Supplies
Warning
Note
Warning
6. Connect the +48 VDC (RTN) feed wire to the terminal block marked
+(plus).
7. Connect the -48 VDC feed wire to the terminal block marked - (minus).
Check to see if there are any exposed copper strands coming from
the installed wires. When this installation is done correctly there
should be no exposed copper wire strands extending from the
terminal block. Any exposed wiring can conduct harmful levels of
electricity to persons touching the wires. E12
8. Secure the tray cable near the rack framework using multiple cable
ties to minimize the chance of the connections being disturbed by
casual contact with the wiring. Use at least four cable ties, separated
100mm (4 in.) apart. Locate the first one within 150mm (6 in.) of the
terminal block.
This system will work with a positive grounded or negative grounded
DC system. E13
9. Verify that the circuit breaker is in the Off position.
10. Connect the supply-cable wires to the circuit breaker.
11. Energize the circuit breaker.
12. Turn the power supply module’s On/Off switch to On.
13. Start a local management session on the unit by performing the
procedure “Starting a Local Management Session,” next.
This unit might have more than one power source. To reduce the
risk of electric shock, disconnect all power cords before servicing the
unit. E30
72
Starting a Local Management Session
Note
S2
/28
S1
/2
7
2
6
2
5
CONSOLE
SFP+
This procedure requires a terminal or a terminal emulator program and the
management cable that comes with the switch. To start a local
management session on the switch, perform the following procedure:
1. Connect the RJ-45 connector on the management cable to the
Console port on the front panel of the switch, as shown below.
x510DP-52GTX Installation Guide
2680
Figure 35. Connecting the Management Cable to the Console Port
2. Connect the other end of the cable to an RS-232 port on a terminal or
PC with a terminal emulator program.
3. Configure the terminal or terminal emulator program as follows:
Baud rate: 9600 bps (The baud rate of the Console Port is
adjustable from 1200 to 115200 bps. The default is 9600 bps.)
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
The port settings are for a DEC VT100 or ANSI terminal, or an
equivalent terminal emulator program.
4. If you have not already done so, power up the switch as described in
the previous procedures.
73
Chapter 4: Installing the Switch and its Power Supplies
Bootloader 2.0.15 loaded
Press <Ctrl+B> for the Boot Menu
Reading filesystem...
Loading flash:x510-5.4.3-3.7.rel...
Verifying release... OK
Booting...
Starting base/first... [ OK ]
Mounting virtual filesystems... [ OK ]
______________ ____
/\ \ / /______\
/ \ \_ __/ /| ______ |
/ \ | | / | ______ |
/ \ \ / / \ ____ /
/______/\____\ \/ /____________/
Allied Telesis Inc.
AlliedWare Plus (TM) v5.4.2A
Current release filename: x510-5.4.3-3.7.rel
Original release filename: x510-5.4.3-3.7.rel
Built: 08-Oct-2013 10:43:42 NZDT 2013 by: maker@maker04-build
Mounting static filesystems... [ OK ]
Checking flash filesystem... [ OK ]
Mounting flash filesystem... [ OK ]
Checking NVS filesystem... [ OK ]
Mounting NVS filesystem... [ OK ]
Starting base/dbus... [ OK ]
Starting base/syslog... [ OK ]
Monitoring the Initialization Processes
It takes about thirty seconds for the switch to initialize its management
software programs and features, and load the default configuration. You
may monitor the progress of the initialization process by watching the
switch ID LED. It displays the number “8” for about the first 15 seconds
and then displays the number “1.”
You may also monitor the bootup sequence by connecting a terminal or
computer that has a terminal emulator program, to the Console port on the
master switch. You will see the messages in Figure 36 here to Figure 38
on page 76.
74
Figure 36. Switch Initialization Messages
Starting base/loopback... [ OK ]
Starting base/sysctl... [ OK ]
Received event poefw.done
Starting base/portmapper... [ OK ]
Received event syslog.done
Starting base/reboot-stability... [ OK ]
Starting base/autofs-card... [ OK ]
Checking system reboot stability... [ OK ]
Starting base/cron... [ OK ]
Starting base/appmond... [ OK ]
Starting hardware/openhpi... [ OK ]
Starting hardware/timeout... [ OK ]
Starting base/inet... [ OK ]
Starting base/modules... [ OK ]
Received event modules.done
Received event board.inserted
Received event hardware.done
Starting network/startup... [ OK ]
Starting network/stackd... [ OK ]
Starting network/election.timeout... [ OK ]
Received event network.enabled
Initializing HA processes:
openhpid, hostd, cntrd, nsm, auth, epsr, hsl
imiproxyd, irdpd, lldpd, loopprot, mstp, ospf6d, ripd
ripngd, rmon, sflowd, udldd, vrrpd, bgpd, imi
lacp, ospfd, pdmd, pimd
Received event network.initialized
03:44:11 awplus-1 VCS[826]: No neighboring members found, unit may be in a
stand alone configuration
03:44:11 awplus-1 VCS[826]: Startup speed can be improved by adding 'no stack
1 enable' to configuration
Received event vcs.elected-master
03:44:11 awplus-1 VCS[826]: Member 1 (0015.774f.ed30) has become the Active
Master
x510DP-52GTX Installation Guide
Figure 37. Switch Initialization Messages (Continued)
75
Chapter 4: Installing the Switch and its Power Supplies
Assigning Active Workload to HA processes:
hsl, nsm, rmond, sflowd, vrrpd, irdpd, lacpd
lldpd, loopprotd, mstpd, authd, epsrd, imi, imiproxyd
Received event network.activated
Loading default configuration
Warning: flash:/default.cfg does not exist, loading factory defaults.
..
done!
Received event network.configured
awplus login:
Figure 38. Switch Initialization Messages (Continued)
76
Chapter 5
Configuring the Switch for Stand-alone Operations
Use this chapter if you wish to operate the switch as a single stand-alone
switch, instead of stacking it with other switches.
This chapter contains the following procedures:
“Configuring the Switch for Stand-alone Operations” on page 78
“Specifying Ports in the Command Line Interface for Stand-alone
Switches” on page 83
77
Chapter 5: Configuring the Switch for Stand-alone Operations
Caution
Note
Caution
awplus>
Configuring the Switch for Stand-alone Operations
Disabling
VCStack
After the switch has initialized its management software, examine the
switch ID LED on the front panel and do one of the following:
If the LED is displaying “0,” the installation procedure is complete.
The switch is now ready for network operations as a stand-alone
unit. Refer to the Software Reference: AlliedWare Plus Operating
System for x510 Series for instructions on how to configure the
operating parameters.
If the LED is displaying a number other than “0,” perform the
following procedures to disable the VCStack feature.
You have to reset the switch as part of the procedure to disabling
the VCStack feature. Some network traffic may be lost if the device
is already connected to a live network.
The initial management session of the switch must be from the
Console port.
To disable the VCStack feature to use the switch as a stand-alone unit,
perform the following procedure:
Disabling the VCStack feature requires resetting the switch. If the
switch is already connected to a live network, some network traffic
may be lost.
1. Unless you have already done so, start a local management session
as described in “Starting a Local Management Session” on page 73.
2. When prompted, enter a user name and password to log on the
switch. If this is the initial management session of the switch, enter
“manager” as the user name and “friend” as the password. The user
name and password are case sensitive.
The local management session starts when the User Exec mode
prompt, shown in Figure 39. is displayed.
78
Figure 39. User Exec Mode Prompt
x510DP-52GTX Installation Guide
Note
awplus> show stack
Virtual Chassis Stacking summary information
ID Pending ID MAC address Priority Status Role
1 - 0015:774f:ed30 128 Ready Active Master
Operational Status Standalone Unit
Stack MAC address 0015:774f:ed30
awplus(config)#
awplus> enable
awplus# configure terminal
Enter configuration commands, one per line. End with CNTL/Z
awplus(config)#
The User Exec mode is the first level in the command mode
interface. For complete information on the modes and commands,
refer to the Software Reference: AlliedWare Plus Operating System
for x510 Series.
3. Enter the SHOW STACK command to display the status of the
VCStack feature. Figure 40 is an example of the command.
Figure 40. SHOW STACK Command
4. Review the following items:
If the Operational Status is “Stacking Hardware Disabled,” the
VCStack feature is already disabled on the switch and the SFP+
stacking slots may be used with regular SFP or SFP+ transceivers.
If the Operational Status is “Standalone Unit,” as shown in Figure
40 on page 79, the VCStack feature is active on the unit. You must
disable it by performing the steps in the rest of this procedure
before you can use the SFP+ stacking slots with regular SFP or
SFP+ transceivers. The reason the status says “standalone” is
because the switch considers itself a stack of one switch.
5. Move to the Global Configuration mode by entering the ENABLE and
CONFIGURE TERMINAL commands, as shown in Figure 41.
Figure 41. Moving to the Global Configuration Mode
6. To. disable the VCStack feature on the switch, enter the NO STACK
ENABLE command, which has this format:
no stack
id
enable
79
Chapter 5: Configuring the Switch for Stand-alone Operations
Warning; This will disable the stacking hardware on member-1.
Are you sure you want to continue? (y/n):
awplus(config)# exit
awplus#
awplus# write
Building configuration ...
[OK]
awplus#
The ID parameter is the ID number of the switch, displayed on the ID
LED. Replace the parameter with whatever number is on the ID LED.
For example, if the ID number of the switch is 1, the default value,
enter the command as follows:
awplus(config)# no stack 1 enable
This confirmation prompt in Figure 42 is displayed.
Figure 42. Confirmation Prompt for the NO STACK ENABLE Command
7. Type Y to disable VCStack on the switch or N to cancel the procedure.
8. Enter the EXIT command to return to the Privileged Exec mode, as
shown in Figure 43.
Figure 43. Returning to the Privileged Exec Mode
9. Enter the WRITE command to save your change in the configuration
file. The switch displays the confirmation prompt in Figure 44 on page
80.
Figure 44. Saving the Changes with the WRITE Command
10. Enter the REBOOT command to reboot the switch.
11. At the confirmation prompt, type “Y” for yes.
12. Wait for the switch to initialize its management software and
afterwards examine the Switch ID LED. The switch is ready for normal
network operations as a stand-alone unit when its ID number is “0.”
Refer to the Software Reference: AlliedWare Plus Operating System
for x510 Series for instructions on how to configure the operating
parameters. If the number is not “0,” repeat this procedure.
80
x510DP-52GTX Installation Guide
awplus>show interface port1.0.51
Interface port1.0.51
Scope: both
Link is DOWN, administrative state is UP
Thrash-limiting
Status Not Detected, Action learn-disable, Timeout 1(s)
Hardware is Ethernet, address is 0015.774f.ed30
index 5051 metric 1 mru 1500
configured duplex auto, configured speed auto, configured polarity auto
<UP,BROADCAST,MULTICAST>
SNMP link-status traps: Disabled
input packets 0, bytes 0, dropped 0, multicast packets 0
output packets 0, bytes 0, multicast packets 0 broadcast packets 0
Time since last state change: 0 days 00:42:49
Confirming the
Status of the
VCStack Feature
Another way to confirm that VCStack is disabled on the switch is by
displaying the status of the last two SFP+ slots on the switch. These are
slots 51 and 52. If VCStack is disabled, you should be able to display the
status of the slots even when they do not have transceivers. If VCStack is
not disabled, the switch displays a message that it cannot find the slots. To
view the status of the stacking slots, perform this procedure:
1. Start a management session on the switch. For directions, refer to
“Configuring the Switch for Stand-alone Operations” on page 78.
2. Log on to the switch. The default user name is “manager” and the
password is “friend”.
3. From either the User Exec mode or Privileged Exec mode, enter the
SHOW INTERFACE command to display the status of one of the last
two SFP+ slots on the switch. For example, enter this command to
view the status of slot 51:
show interface port1.0.51
If VCStack is disabled, the switch displays the status of the designated
slot. An example is shown in Figure 45 on page 81.
Figure 45. Status of a Stacking Slot When VCStack is Disabled
81
Chapter 5: Configuring the Switch for Stand-alone Operations
awplus# show interface port1.0.51
%Can’t find interface port1.0.51
awplus#
The switch displays the message in Figure 46 on page 82 if VCStack is
not disabled, in which case you need to disable it by performing the
commands in “Disabling VCStack” on page 78.
Figure 46. Status of a Stacking Slot When VCStack is Enabled
82
x510DP-52GTX Installation Guide
port1.0
.n
Module ID
Port Number
Stack ID
Specifying Ports in the Command Line Interface for Stand-alone Switches
The command line interface in the management software on the switch
has a parameter that you use to specify the individual ports. The
parameter is the PORT parameter and Figure 47 shows its format.
Figure 47. PORT Parameter in the Command Line Interface
The first number is the switch’s ID number. The ID number for stand-alone
switches is not the value 0 displayed on the Switch ID LEDs. Rather, it is 1.
Be sure to enter 1, not 0, as the ID number in the PORT parameter when
configuring ports on stand-alone switches.
The module ID value is used with multi-module products. This value does
not apply to the x510 Series switches and should always be 0.
The third value is a port number on the switch. You may specify only one
port number in a PORT parameter, but you may specify more than one
PORT parameter in many commands where the parameter is supported.
Here is an example of the PORT parameter on a stand-alone switch. It
uses the INTERFACE command to enter the Port Interface mode for ports
15 and 17:
awplus> enable
awplus# configure terminal
awplus(config)# interface port1.0.15,port1.0.17
For instructions on the command line interface and the PORT parameter,
refer to the Software Reference: AlliedWare Plus Operating System for
x510 Series.
83
Chapter 5: Configuring the Switch for Stand-alone Operations
84
Chapter 6
Verifying the Status of VCStack and Activating VCStack
The procedures in this chapter are:
“Verifying the Status of VCStack” on page 86
“Activating the VCStack Feature” on page 87
85
Chapter 6: Verifying the Status of VCStack and Activating VCStack
Verifying the Status of VCStack
Before you install the stacking transceivers to build the stack, you should
first test the switches to determine whether the VCStack feature is
enabled or disabled, and enable it on any units where it is disabled. On
new switches, the feature should be activated because that is the default
setting. But on switches that were previously used as stand-alone units,
the feature is probably disabled and needs to be enabled.
Testing the status of VCStack is simple. You power on a switch and watch
the ID LED. If it displays a number from 1 to 4, VCStack is already
enabled. If the LED displays the number 0, the feature is disabled and
needs to be enabled.
To test the status of VCStack, perform the following procedure:
1. Power on one of the switches.
Connect a power cord to one of the power connectors on the back
panel and to an AC power source. The unit has two power connectors,
but you do not need to connect both power cords for this procedure.
2. Wait one minute for the switch to initialize its management software.
3. View the ID LED and do one of the following:
If the ID LED is displaying a number from 1 to 4 (1 is the default),
VCStack is already enabled on the switch. Power off the unit by
disconnecting the power cord and test the remaining switches in
the same manner. After testing all the switches, be sure the
switches are powered off and go to Chapter 7, “Cabling the
Stacking Ports” on page 91.
If the ID LED is displaying “0,” the VCStack feature is disabled on
the switch. You must enable it by performing the procedure in
“Activating the VCStack Feature” on page 87.
86
Activating the VCStack Feature
Note
awplus>
awplus> enable
awplus#
Perform the following procedure to activate the VCStack feature on
switches that display the number “0” on their ID LEDs in the previous
procedure. The tasks follow on from “Monitoring the Initialization
Processes” on page 74.
x510DP-52GTX Installation Guide
Activating
VCStack
To activate VCStack, perform the following procedure:
1. Unless you have already done so, start a local management session
as described in “Starting a Local Management Session” on page 73.
2. When prompted, enter a user name and password to log on the switch.
If this is the initial management session of the switch, enter “manager”
as the user name and “friend” as the password. The user name and
password are case sensitive.
The local management session starts when the User Exec mode
prompt, shown in Figure 48. is displayed.
Figure 48. User Exec Mode Prompt
The User Exec mode is the first level in the command mode
interface. For complete information on the modes and commands,
refer to the Software Reference: AlliedWare Plus Operating System
for x510 Series.
3. Enter the ENABLE command to move from the User Exec mode to the
Privileged Exec mode, as shown in Figure 49.
Figure 49. Moving to the Privileged Exec Mode with the ENABLE
Command
87
Chapter 6: Verifying the Status of VCStack and Activating VCStack
Note
awplus# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
awplus(config)#
awplus(config)# stack enable
% The device needs to be restarted for this change to take effect.
awplus(config)#
awplus(config)# exit
awplus#
awplus# write
Building configuration ...
[OK]
awplus#
4. Enter the CONFIGURE TERMINAL command to move to the Global
Configuration mode, as shown in Figure 50.
Figure 50. Moving to the Global Configuration Mode with the CONFIGURE
5. Enter the STACK ENABLE command to activate VCStack on the
switch, as shown in Figure 51 on page 88:
Figure 51. Activating VCStack with the STACK ENABLE Command
TERMINAL Command
6. Enter the EXIT command to return to the Privileged Exec mode, as
shown in Figure 52.
Figure 52. Returning to the Privileged Exec Mode with the EXIT Command
7. Enter the WRITE command to save your change, as shown in
Figure 53.
Figure 53. Saving the Change with the WRITE Command
If this is the initial management session of the switch, the WRITE
command automatically creates in flash memory a new
configuration file called DEFAULT.CFG in which it stores your
configuration change. You may change the name of the file or
designate a different file after you create the stack.
88
x510DP-52GTX Installation Guide
awplus# reboot
reboot system? (y/n):
awplus#
8. Restart the switch with the REBOOT command, as shown in
Figure 54.
Figure 54. Rebooting the Switch with the REBOOT Command
9. Type “Y” for yes.
10. Wait one minute for the switch to initialize its management software.
11. Check the ID LED and do one of the following:
If the ID LED is displaying the number 1, 2, 3, or 4, VCStack is now
enabled on the switch. Power off the switch by disconnecting the
power cord and repeat the procedures in this chapter on the next
switch. If there are no further switches to test, go to Chapter 7,
“Cabling the Stacking Ports” on page 91.
If the ID LED is still displaying “0,” repeat this procedure. If the
procedure was not successful, it might be because you did not
issue the WRITE command in step 5 to save your change.
89
Chapter 6: Verifying the Status of VCStack and Activating VCStack
90
Chapter 7
Cabling the Stacking Ports
This chapter contains the following procedures:
“Cabling Switches with AT-StackXS/1.0 Transceivers” on page 92
“Cabling Switches with AT-StackOP/0.3 or AT-StackOP/9.0
Transceivers” on page 97
91
Chapter 7: Cabling the Stacking Ports
Warning
S2/28
S1/2
7
26
25
CON
SO
LE
SFP+
2681
Cabling Switches with AT-StackXS/1.0 Transceivers
To cable the switches of the stack with AT-StackXS/1.0 transceivers,
perform the following procedure:
A transceiver can be damaged by static electricity. Be sure to
observe all standard electrostatic discharge (ESD) precautions,
such as wearing an antistatic wrist strap, to avoid damaging the
device.
1. Remove the dust plug from the S1 slot on the top switch of the stack,
as shown in Figure 55.
92
Figure 55. Removing the Dust Plug from the S1 Slot
2. Remove the transceiver from its shipping container and store the
packaging material in a safe location.
x510DP-52GTX Installation Guide
3. Remove the dust cap from one end of the transceiver, as shown in
Figure 56 on page 93.
Figure 56. Removing the Dust Cover from the AT-StackXS/1.0
Transceiver
93
Chapter 7: Cabling the Stacking Ports
S2/28
S1/27
26
25
CON
SO
LE
SFP+
Release tab
4. Position the transceiver with the release tab on top and slide the
transceiver into the slot, as shown in Figure 57 on page 94.
2683
94
Figure 57. Installing the AT-StackXS/1.0 Transceiver in Slot S1
x510DP-52GTX Installation Guide
Note
S2/28
S1/2
7
2
6
25
CON
SO
LE
SFP+
5. Remove the dust cover from the S2 slot in the next switch in the stack
as shown in Figure 58 on page 95.
The cable must crossover to different slots on the switches. The
stack will not work if you connect two S1 or S2 slots together.
2684
Figure 58. Removing the Dust Plug from the S2 Slot
6. Remove the dust cover from the connector on the other end of the
transceiver.
95
Chapter 7: Cabling the Stacking Ports
S2
/28
S1/2
7
26
25
CON
SO
LE
SFP+
7. Position the transceiver with the release tab on the bottom and slide it
into the slot until it clicks into place, as shown in Figure 59 on page 96.
2685
96
Figure 59. Installing the AT-StackXS/1.0 Transceiver in Slot S2
8. Repeat this procedure to connect additional switches to the stack with
AT-StackXS/1.0 transceivers.
9. To create the redundant path with the ring topology shown in Figure 15
on page 42 and Figure 16 on page 43, connect a stacking cable to the
empty stacking slots on the top and bottom switches.
10. After connecting the stacking cables to all the switches, go to Chapter
8, “Powering On the Stack” on page 101.
x510DP-52GTX Installation Guide
Handle
Cabling Switches with AT-StackOP/0.3 or AT-StackOP/9.0 Transceivers
For guidelines to cabling the switches with AT-StackOP/0.3 or ATStackOP/9.0 fiber optic transceivers, refer to “Planning a Stack” on
page 53. To cable switches with fiber optic transceivers, perform the
following procedure:
1. Remove a dust cover from either the S1 or S2 slot on the switch.
2. To install the transceiver in the S1 slot, position it with the handle on
top, as shown in Figure 60. To install it in the S2 slot, position it with
the handle on the bottom.
Figure 60. Handle on the AT-StackOP/0.3 and AT-StackOP/9.0
Transceivers
97
Chapter 7: Cabling the Stacking Ports
S2/28
S1
/2
7
26
25
CON
SO
LE
SFP+
S2/28
S1
/27
26
25
CON
SO
LE
SFP+
2688
3. Slide the transceiver into the slot until it clicks into place, as shown in
Figure 61 on page 98.
2687
98
Figure 61. Installing the AT-StackOP/0.3 or AT-StackOP/9.0 Transceiver
x510DP-52GTX Installation Guide
S2/28
S1/2
7
26
25
CON
SO
LE
SFP+
S2/28
S1/27
26
25
CON
SO
LE
SFP+
SFP Handle
4. Remove the dust cover from the transceiver, as shown in Figure 62 on
page 99.
2689
Figure 62. Removing the Dust Cover from a Stacking Transceiver
5. Verify the position of the handle on the transceiver. If the transceiver is
in the S1 slot, the handle should be in the upright position, as shown in
Figure 63. If the transceiver is in the S2 slot, the handle should be in
the down position.
2690
Figure 63. Positioning the Handle in the Upright Position
99
Chapter 7: Cabling the Stacking Ports
S2/28
S1/27
26
25
CON
SO
LE
SFP+
2691
6. Connect the fiber optic cable to the transceiver, as shown in Figure 64
on page 100. The connector on the cable should fit snugly into the
port, and the tab should lock the connector into place.
Figure 64. Connecting the Fiber Optic Cable to the Stacking Transceiver
7. Repeat this procedure if the switch is to have two stacking
transceivers.
8. Repeat this procedure on the other switches of the stack to install their
stacking transceivers. The connections must crossover such that a
transceiver in slot 1 connects to a transceiver in slot 2.
9. After you connect the stacking cables to all the switches, go to Chapter
8, “Powering On the Stack” on page 101.
100
Loading...