Related Documents
The Allied Telesyn web site at www.alliedtelesyn.com provides you with an easy
way to access the most recent documentation, software, and technical information
for all of our products. For details on the features and functions of your Allied
Telesyn AT-WD1008 chassis and modules, refer to the following manuals from our
web site:
To install the AT- WDRPS-10, perfor m the following pr ocedure:
Note
The AT-WDRPS-10 u n it can be installed while the mu ltiplexer is powered ON.
You do not need to power OFF the multiplexe r to insta l l th e RPS.
AT-WDRPS-10
Redundant Power Supply (AC)
Installation Guide
Allied Telesyn, Inc.
960 Stewart Drive, Suite B
Sunnyvale, CA 94085 USA
Tel 1 (408) 730-0950 • Fax 1 (408) 736-0100
Visit our web site at: www.alliedtelesyn.com
Overview
The AT-WDRPS-10 is an AC Redundant Power Supply (RPS) for the AT-WD1008
Multiplexer chassis. When installed, the unit shares the load of poweri n g the
chassis with the standard power supply that comes pre-installed in the chassis. If a
power supply fails, the remaining unit provides all power to the system, thereby
preventing a network failure. The power supply is hot-swappable, meaning that
you can install it while the chassis is powered ON.
❑ AT-WD1008 Gigabit Ethernet Wavelength Division Multiplexer
Installation Guide
PN 613-50367-00
❑ AT-S47 Management Software User’s Guide
PN 613-50371-00
Package Contents
Make sure the following items are included in the shipping package. If any item is
missing or damaged, contact your Allied Telesyn sales representative for
assistance.
❑ One AT-WDRPS-10 Redundant Power Supply (AC) Module
❑ One AC Power Cord
❑ This installation gu ide
❑ Warranty card
Installing the AT-WDRPS-10 Power Supply
Caution
Before installing the module, refer to the AT-WD1008 Installation Guide for
electrical safety and emission informati on.
Caution
Do not install the AT-WDRPS-10 module in an AT-WD1008 chassis designed
for DC power. An AC powered chassis has two AC power sockets on the back
panel.
1. Loosen the two thumbscrews that secure the blank faceplate over the righthand redundant power supply expansion slot located on the front panel of the
AT-WD1008 Multiplexer and remove the cove r.
TX
TX
L
N
K
T
S
T
RX
L
N
K
T
S
T
T
X
WEST
RX
T
R
X
X
EAST
R
X
L
N
K
T
S
T
N
O
R
M
A
L
S
N
M
P
M
O
D
U
L
E
TX
RX
TX
C
H
5
RX
P
O
W
E
S
U
P
P
L
Y
TX
E
A
S
T
RX
TX
C
H
6
RX
R
B
TX
RX
TX
C
H
7
RX
TX
TX
FAN A
C
H
8
RX
FAN B
2. Remove the AT-WDRPS-10 unit from its shipping package.
3. Slide the AT-WDRPS-10 unit into the RPS expansion slot.
T
X
TX
L
N
K
T
S
W
RX
E
S
SNMP MODULE
AT-WDRPS-10
T
T
X
R
T
X
R
XT
L
N
K
T
S
T
T
X
E
A
S
R
T
X
L
N
K
T
S
T
N
O
R
M
A
L
P
O
F
A
X
R
X
TX
CH 5
RX
POWER
SUPPLY B
W
E
R
U
L
T
T
EAST
X
R
X
TX
CH 6
RX
T
X
R
X
TX
CH 7
RX
T
X
TX
FAN A
CH 8
RX
FAN B
AT-WDRPS-10
PN 613-50369-00 Rev A
P
O
W
E
R
F
A
U
L
T
1 2 3
4. Secure the AT-WDRPS-10 unit to the AT -WD1008 chassis b y tightening th e two
thumbscrews.
TX
TX
L
N
K
T
S
T
T
X
WEST
RX
R
X
S
N
M
P
RX
L
N
K
T
S
T
T
X
EAST
R
X
L
N
K
T
S
T
N
O
R
M
A
L
M
O
D
U
L
E
TX
RX
TX
C
H
5
RX
P
O
W
E
R
S
U
P
P
L
Y
B
TX
E
A
S
T
RX
TX
C
H
6
A
T-W
RX
D
R
P
S
-10
POWER
FAULT
TX
RX
TX
C
H
7
RX
TX
TX
FAN A
C
H
8
RX
FAN B
Note
If you are installing the AT-WD1008 Multiplexer for the first time, refer to the
AT-WD1008 Installation Guide for instructi ons on how to complete the
installation.
5. Connect the power cord to the RPS AC power connector, located in the back of
the multiplexe r, a nd the other end o f the cord to an approp riate AC power
source.
Technical Specifications
Electrical Rating
Input Voltage 100 - 240 V AC, 3.2A maximum
AC Input Frequency: 47-63 Hz
Power Comsumption 75 watts maximum
Environment
Operating Temperature : 0° C to 40° C (32° F to 104° F)
Storage Temperature: -25° C to 70° C (-13° F to 158° F)
Operating Relative Humi dit y : 5% to 90% RH (non-condensing)
Storage Relative Humidity: 5% to 95% RH (non-condensing)
Operating Altitude Range: Up to 3,000 m (9,843 ft)
Electrical Safety and Emission Statement
Standards: This product meets the following standards when installed in compliant host equipment.
U.S. Federal Communications Commis sion
RADIATED EN ERGY
Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to
Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with this instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void your right to
operate this equipment.
Industry Canada
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du
Canada.
Emission FCC Class A, EN55022 Class A, VCCI Class A, EN6100-3-2, EN6100-3-3
WARNING: In a domestic environment this product may cause radio interference in which case the user may be
Immunity EN55024
Electrical Safety UL60950 (cULus), EN60950 (TUV)
required to take adequate measures.
AT-WDFAN01
Power ON/OFF
Switch for
the Optional
RPS Module
AC Power Inl e t
for the Optional
RPS Module
AC Power Inlet
for the Standard
Power Module
Power ON/OFF
Switch for
the Standard
Power Module
6. Turn the RPS power s w itch to the ON p osition.
7. Check that the POWER LED on the front of the RPS module is green. If the
POWER LED is OF F or the FAULT LED is O N , r efer to the AT-WD1008 Installation
Guide for troubleshooting instructions.
Note
For added power protection to the mu ltiplexer, the two AC power cords
should be conne cted to power sou r ces that are oper a ting from different
power circuits. This will protect the mult iplexer from a power loss should one
of the power circuits fail.
This completes the installation procedure for the AT-WDRPS-10 unit.
Copyright 2003 Allied Telesyn, Inc. All rights reserved.
No part of this publication may be reproduced without prior written permission from Allied Telesyn Inc.
4 5 6