How it Works
Allen&Heath
Loading...
PL-10
User Manual
2 pgs859.04 Kb0

Allen&Heath PL-10 User Manual

PL-10 Rotary Encoder Remote AP5708
User Guide
Introduction The PL-10 adds to the extensive range of remote control devices available for the iDR-4/8 audio
mix processor and iLive mixing systems. It offers an alternative to the PL-6 fader controller with the advantage that user settings can be stored and recalled without the need to physically move the controls to the new settings.
8 Rotary Encoders can be configured individually for continuous input, output, group, crosspoint level control or monitor level. Minimum and maximum ranges can be set. Each rotary encoder has 8 LEDs displaying the control position. 16 Switches, arranged as two per rotary encoder, can be configured as combinations of level up/down, mute toggle, polarity toggle, audio monitor select, or preset recall. 24 LED indicators, arranged as three per fader, can be configured as combinations of 3 colour signal meters, mute status, channel on indication, level sensing or preset related 3 colour LED indication. Controls can be disabled if not required. A single 3 colour Status LED displays PL­Anet power and communication status. Custom labels can be fitted into the recessed areas provided (13 x 7mm). Recommended label height is 6mm.
NOTE: Check the Allen & Heath web site for the latest version of iDR-4/8 or iLive firmware and software:
www.allen-heath.com
This product complies with the European Electromagnetic Compatibility directive 2004/108/EC.
NOTE: Any changes or modifications to the equipment not approved by Allen & Heath could void the compliance of the equipment. Whilst we believe the information in this guide to be reliable we do not assume responsibility for inaccuracies. We also reserve the right to make changes in the interest of further product development.
Copyright© 2011 Allen & Heath Ltd. All rights reserved.
IMPORTANT :
Observe the local standards which may apply to the installation regarding the grade of cable and installation methods.
Do not install the equipment where it is subject to moisture, heat, vibration or excessive movement.
Connect this equipment to the Allen & Heath PL-Anet port only. Test for correct wiring and installation before switching the equipment on.
PL-10 User Guide AP5708 issue 2 1
Number of devices The maximum number of
PL devices that can be connected depends on their
type, cable lengths and PL-Anet Bus Speed. Up to 18x PL-10 devices may be connected in an iDR system with the half speed PL-A-net Bus setting. Fewer devices may be connected if long distances, full bus speed or other PL types are involved. Long distances up to 300m (1000’), and star point connection are possible if the optional PL-9 PL-Anet hub is used. Before starting, refer to the PL Combinations Calculator spreadsheet available as a download from the Allen & Heath web site.
iDR
PL-9 HUB
TERMINATION
TERMINATION
TERMINATION
PL-Anet is the proprietary Allen & Heath system
for daisy chaining remote controllers. It is an RS485 serial connection that uses CAT5 STP cable to communicate between devices over long distances. It requires a terminator at the last unit in the chain. PL­Anet only works with Allen & Heath PL devices. The connection includes +20V DC to power the connected devices. The iDR-8 port is shown here.
DR-LINK AUDIO OUTAUDIO IN
PL-ANET
CAUTION 20V DC
TO AVOID DAMAGE ONLY CONNECT COMPATIBLE REMOTE CONTROL EQUIPMENT TO THE P L-ANET PORT.
DIGITAL EXPANDER
Mounting into furniture Cutting template
details are shown here for mounting the PL-10 into a plinth or other furniture. Secure the unit in place using 4x fixing screws up to 3.5mm diameter.
51
37
PL-Anet connections Underside RJ45 ports
are provided for connecting to PL-Anet. These are recessed so that the cables can be hidden from view. The IN port connects to the previous unit in the chain. The OUT port connects to the next unit, or end of chain termination. Use flame retardent CAT5 STP (shielded twisted pair) RJ45 cables.
PL-Anet
IN OUT
previous next
CAUTION 20V DC
TO AVOID DAMAGE ONLY CONNECT COMPATIBLE REMOTE CONTROL EQUIPMENT TO THE PL-Anet PORT.
SERIAL NUMBER
AN5709
Made in the UK by ALLEN&HEATH LIMITED
PL-10
TERMINATOR
PLUG
End of chain termination As with any
RS485 system, the last PL device needs to have a terminating resistor fitted to its output port. The PL-10 is shipped with an RJ45 terminator plug with this resistor built in. Plug the terminator into the last unit in the PL-Anet chain. If the PL-10 is the only unit connected make sure the terminator is plugged into its output port.
Testing the wiring Before powering up the system make sure all the wiring is inspected and continuity tested. This is important as wiring errors may result in damage to the equipment.
Powering up the PL system Ensure that
the iDR PL-Anet port is active. Its green ‘active’ LED should be lit. If not, use the iDR System Manager software Communications Option menu to activate the port. Plug in the PL-Anet cable. The screen will display icons on the right hand toolbar for each PL device it recognises. Check that the PL-10 front panel status LED displays green. If red or yellow is displayed then check for wiring or equipment faults.
STATUS
Configuring the controls The rotary
encoders, switches and LED indicators are configured using the iDR System Manager software. Note that the LEDs are 3-colour and can display green, red, yellow or off. Refer to the Help file that comes with the software.
170.5
92
DIA 4
CUTOUT
212 x 147 mm
Allows 1mm clearance each side
156.5
LED / SOFTKEYS
LED / SOFTKEYS
LEDs
ENCODERS
LED
225
Grounding The exposed metal panels are
grounded through the PL-Anet cable shield. There are
Further information Visit the Allen & Heath
web site for information on the full PL product range www.allen-heath.com. If further assistance is required please contact Allen & Heath technical support.
no dangerous voltages inside.
2 PL-10 User Guide AP5708 issue 2
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use