Allen & Heath MPS14 User Manual

MPS14

Rack Mount Power Supply

USER GUIDE

Publication AP3898

Limited One Year Warranty

This product has been manufactured in the UK by ALLEN & HEATH and is
warranted to be free from defects in materials or workmanship for period of one
year from the date of purchase by the original owner.

To ensure a high level of performance and reliability for which this equipment has
been designed and manufactured, read this User Guide before operating.

In the event of a failure, notify and return the defective unit to ALLEN & HEATH or
its authorised agent as soon as possible for repair under warranty subject to the
following conditions

Conditions Of Warranty

1. The equipment has been installed and operated in accordance with the
instructions in this User Guide

2. The equipment has not been subject to misuse either intended or accidental,
neglect, or alteration other than as described in the User Guide or Service
Manual, or approved by ALLEN & HEATH.

3. Any necessary adjustment, alteration or repair has been carried out by ALLEN
& HEATH or its authorised agent.

4. The defective unit is to be returned carriage prepaid to ALLEN & HEATH or its
authorised agent with proof of purchase.

5. Units returned should be packed to avoid transit damage.

In certain territories the terms may vary. Check with your ALLEN & HEATH agent
for any additional warranty, which may apply.

This product complies with the European Electromagnetic
Compatibility directives 89/336/EEC & 92/31/EEC and the
European Low Voltage Directives 73/23/EEC & 93/68/EEC.

Any changes or modifications to the power unit not approved by Allen & Heath
could void the compliance of the product and therefore the users authority to
operate it.

MPS14 User Guide AP3898 Issue 4.

Copyright © 2001 Allen & Heath. All rights reserved

Manufactured in the United Kingdom by Allen & Heath Limited

Kernick Industrial Estate, Penryn, Cornwall, TR10 9LU, UK

http://www.allen-heath.com

2 MPS14 User Guide

Important Safety Instructions

WARNINGS - Read the following before proceeding :

CAUTION

ATTENTION: RISQUE DE CHOC ELECTRIQUE – NE PAS OUVRIR

Read instructions: Retain these safety and operating instructions for future reference. Adhere to

all warnings printed here and on the power unit. Follow the operating
instructions printed in this User Guide.

Do not remove covers: Operate the power unit with its covers correctly fitted. Refer any service work

on the power unit to competent technical personnel only.

Power sources: Connect the power unit to a mains power only of the type described in this

User Guide and marked on the rear panel. Use only the power cord with
sealed mains plug appropriate for your local mains supply as provided with
the power unit. If the provided plug does not fit into your outlet consult your
service agent for assistance.

Power cord routing: Route the power cord so that it is not likely to be walked on, stretched or

pinched by items placed upon or against it.

Grounding: Do not defeat the grounding and polarisation means of the power cord plug.

Do not remove or tamper with the ground connection in the power cord.

WARNING: This equipment must be earthed.

Water and moisture: To reduce the risk of fire or electric shock do not expose the power unit to rain

or moisture or use it in damp or wet conditions. Do not place containers of
liquids on it which might spill into any openings.

Ventilation: Do not obstruct the ventilation slots or position the power unit where the air

flow required for ventilation is impeded. If the power unit is to be operated in a
flightcase ensure that it is constructed to allow adequate ventilation.

Heat and vibration: Do not locate the power unit in a place subject to excessive heat or direct

sunlight as this could be a fire hazard. Locate the power unit and its power
unit away from any equipment which produces heat or causes excessive
vibration.

Servicing: Switch off the equipment and unplug the power cord immediately if it is

exposed to moisture, spilled liquid, objects fallen into the openings, the power
cord or plug become damaged, during lightening storms, or if smoke, odour or
noise is noticed. Refer servicing to qualified technical personnel only.

Installation: Install the power unit in accordance with the instructions printed in this User

Guide. Do not connect the output of power unit to any other equipment other
than that specified by Allen & Heath.

MPS14 User Guide 3