For models with serial number starting W31222 and W31622
FX
USER GUIDE
Publication AP5331
Limited One Year Warranty
This product is warranted to be free from defects in materials or workmanship for
a period of one year from the date of purchase by the original owner.
To ensure a high level of performance and reliability for which this equipment has
been designed and manufactured, read this User Guide before operating. In the
event of a failure, notify and return the defective unit to ALLEN&HEATH Limited
or its authorised agent as soon as possible for repair under warranty subject to
the following conditions
Conditions Of Warranty
1. The equipment has been installed and operated in accordance with the
instructions in this User Guide
2. The equipment has not been subject to misuse either intended or accidental,
neglect, or alteration other than as described in the User Guide or Service
Manual, or approved by ALLEN&HEATH.
3. Any necessary adjustment, alteration or repair has been carried out by
ALLEN&HEATH or its authorised agent.
4. This warranty does not cover fader wear and tear.
5. The defective unit is to be returned carriage prepaid to ALLEN&HEATH or its
authorised agent with proof of purchase.
6. Units returned should be packed to avoid transit damage.
In certain territories the terms may vary. Check with your ALLEN&HEATH agent
for any additional warranty which may apply.
This product complies with the European Electromagnetic
Compatibility directives 89/336/EEC & 92/31/EEC and the
European Low Voltage Directives 73/23/EEC & 93/68/EEC.
This product has been tested to EN55103 Parts 1 & 2 1996 for use in
Environments E1, E2, E3, and E4 to demonstrate compliance with the
protection requirements in the European EMC directive 89/336/EEC.
During some tests the specified performance figures of the product
were affected. This is considered permissible and the product has
been passed as acceptable for its intended use. Allen & Heath has a
strict policy of ensuring all products are tested to the latest safety and
EMC standards. Customers requiring more information about EMC and
safety issues can contact Allen & Heath.
NOTE: Any changes or modifications to the console not approved by
Allen & Heath could void the compliance of the console and therefore
the users authority to operate it.
Kernick Industrial Estate, Penryn, Cornwall, TR10 9LU, UK
http://www.allen-heath.com
2WZ316:2 and 12:2 User Guide
Important Safety Instructions
WARNINGS
- Read the following before proceeding :
CAUTION
ATTENTION: RISQUE DE CHOC ELECTRIQUE – NE PAS OUVRIR
Read instructions: Retain these safety and operating instructions for future reference. Adhere
to all warnings printed here and on the console. Follow the operating
instructions printed in this User Guide.
Do not remove cover: Operate the console with its covers correctly fitted. Disconnect mains
power by unplugging the power cord if the cover needs to be removed for
setting internal options. Refer this work to competent technical personnel
only.
Power sources:Connect the console to a mains power unit only of the type described in
this User Guide and marked on the rear panel. Use the power cord with
sealed mains plug appropriate for your local mains supply as provided with
the console. If the provided plug does not fit into your outlet consult your
service agent for assistance.
Power cord routing:Route the power cord so that it is not likely to be walked on, stretched or
pinched by items placed upon or against it.
Grounding: Do not defeat the grounding and polarisation means of the power cord
plug. Do not remove or tamper with the ground connection in the power
cord.
WARNING: This equipment must be earthed.
Water and moisture: To reduce the risk of fire or electric shock do not expose the console to
rain or moisture or use it in damp or wet conditions. Do not place
containers of liquids on it which might spill into any openings.
Ventilation:Do not obstruct the ventilation slots or position the console where the air
flow required for ventilation is impeded. If the console is to be operated in
a rack unit or flightcase ensure that it is constructed to allow adequate
ventilation.
Heat and vibration: Do not locate the console in a place subject to excessive heat or direct
sunlight as this could be a fire hazard. Locate the console away from any
equipment which produces heat or causes excessive vibration.
Servicing:Switch off the equipment and unplug the power cord immediately if it is
exposed to moisture, spilled liquid, objects fallen into the openings, the
power cord or plug become damaged, during lightening storms, or if
smoke, odour or noise is noticed. Refer servicing to qualified technical
personnel only.
Installation:Install the console in accordance with the instructions printed in this User
Guide. Do not connect the output of power amplifiers directly to the
console. Use audio connectors and plugs only for their intended purpose.
WZ316:2 and 12:2 User Guide 3
Important Mains plug wiring instructions.
The console is supplied with a moulded mains plug fitted to the AC
mains power lead. Follow the instructions below if the mains plug has
to be replaced. The wires in the mains lead are coloured in
accordance with the following code:
TERMINAL
L
LIVE BROWN BLACK
N
NEUTRAL BLUE WHITE
E
EARTH GND GREEN & YELLOW GREEN
The wire which is coloured Green and Yellow must be connected to the
terminal in the plug which is marked with the letter E or with the Earth
symbol. This appliance must be earthed.
The wire which is coloured Blue must be connected to the terminal in
the plug which is marked with the letter N.
The wire which is coloured Brown must be connected to the terminal in
the plug which is marked with the letter L.
Ensure that these colour codes are followed carefully in the event of
the plug being changed.
General Precautions
WIRE COLOUR
European USA/Canada
Damage :To prevent damage to the controls and cosmetics avoid placing heavy
objects on the control surface, scratching the surface with sharp objects,
or rough handling and vibration.
Environment :Protect from excessive dirt, dust, heat and vibration when operating and
storing. Avoid tobacco ash, smoke, drinks spillage, and exposure to rain
and moisture. If the console becomes wet, switch off and remove mains
power immediately. Allow to dry out thoroughly before using again.
Cleaning :Avoid the use of chemicals, abrasives or solvents. The control panel is
best cleaned with a soft brush and dry lint-free cloth. The faders, switches
and potentiometers are lubricated for life. The use of electrical lubricants
on these parts is not recommended. The fader and potentiometer knobs
may be removed for cleaning with a warm soapy solution. Rinse and allow
to dry fully before refitting them.
Transporting :The console may be transported as a free-standing unit or mounted in a
rack or flightcase. Protect the controls from damage during transit. Use
adequate packing if you need to ship the unit.
Hearing :To avoid damage to your hearing do not operate any sound system at
excessively high volume. This also applies to any close-to-ear monitoring
such as headphones. Continued exposure to high volume sound can
cause frequency selective or wide range hearing loss.
4WZ316:2 and 12:2 User Guide
Introduction
Welcome to the Allen & Heath WZ
compact audio mixing consoles. We have tried to keep this user guide brief and to the point.
Please read it fully before starting. Included is information on installing, connecting and
operating the console, panel drawings, system block diagram and technical specification.
For further information on the basic principles of audio system engineering, please refer to
one of the specialist publications and resources available from bookshops, audio equipment
dealers and the Internet.
Whilst we believe the information in this guide to be reliable we do not assume responsibility
for inaccuracies. We also reserve the right to make changes in the interest of further product
development.
We are able to offer further product support through our world-wide network of approved
dealers and service agents. You can also access our Web site on the Internet for
information on our full product range, our company pedigree, assistance with your technical
queries, our contact details or simply to chat about matters audio ( www.allen-heath.com
help us provide the most efficient service please keep a record of your console serial
number, and date and place of purchase to be quoted in any communication regarding this
product.
Note: This user guide refers to models equipped with a revised effects engine. This is
identified by a change from green to yellow effects preset indicators, and a change of serial
number from prefix W31202 to W31222, or W31602 to W31622. Note that these effects are
not compatible with the original WZ Effects Editor PC software. Refer to the Allen & Heath
web site for further information.
3
, the latest generation of the popular MixWizard series of
The Allen & Heath MixWizard series of consoles includes several models. This user guide
describes the WZ
input WZ
3
20S consoles are described in separate publications. For further information on
3
16:2 and WZ312:2 stereo models. The 4 group WZ314:4:2 and stereo
the MixWizard series please refer to the Allen & Heath web site.
The MixWizard is a compact console designed for
professional live sound mixing. It is built to the same
high standards as our top of the range consoles, with
individual circuit cards, potentiometers nutted to the
panel for absolute strength, steel chassis, and no
compromise circuit design ensuring the finest sonic
performance.
The console can be operated free standing or in a
19” rack or flightcase. It is supplied with protective
side trims fitted. These can be removed for rack
mounting. The rear connector pod can be easily
rotated for rear facing or underside connectors when
rack mounted.
Both models feature a 4 band semi-parametric EQ
and high pass filter per mic/line channel, 6 aux sends
with combinations of pre/post switching, 100mm
faders, a built-in dual effects processor with
parameter control using Allen & Heath PC software,
dedicated mono output with separate fader and
innovative operating mode for aux fed sub systems,
additional AB stereo output, comprehensive metering
and engineers monitoring, dual redundant backup
supply input, and a lamp socket.
The WZ
stereo return inputs, a total of 20 input connections.
The WZ
3
16:2 provides 16 mono mic/line inputs and 2
3
12:2 provides 10 mono mic/line inputs, 2 full
channel dual stereo inputs, and 2 stereo return
inputs, a total of 22 input connections.
The base of the console can be removed to access a
host of internal option jumpers. These set user
preference for the aux, direct output and AB sources.
The aux outputs are impedance balanced but may
be electronically balanced if required by fitting an
optional part. A kit is also available to fit the optional
Sys-Link II output card which allows the console to
be linked to other Allen & Heath consoles.
Software for editing the effects parameters using a
PC computer can be downloaded free from the Allen
& Heath web site.
Other accessories available include the Allen &
Heath MPS12 backup power supply and LEDlamp
gooseneck lamp with built-in dimmer.
WZ316:2 and 12:2 User Guide 7
Installing the Console
Free Standing
The console is supplied ready for free standing operation with its side trims fitted and
connector pod positioned for rear access. If you are converting from rack to free standing
then make sure the pod is correctly rotated and secured, and the side trims fitted as shown:
5
194
RELEASE M4 POZI SCREW EACH SIDE
ROTATE POD AND REFIT SECURING SCREWS
19” Rack Mount
For rack mounting, remove the two side trims and rotate the pod into the connector position
preferred. Allow enough space for the cables and connectors behind the console.
5
FIT SIDE TRIMS - 4x M4 POZI SCREWS PER SIDE
CONSOLE WIDTH = 507mm
1
2
58
514
530
193
122
193
101.6165.1101.637.7
497
(11.2U)
444
(10U)
SECURE IN RACK USING 8x M6 BOLTS
USE PLASTIC CUP WASHERS TO PROTECT THE PANEL
482.6 (19" RACK)
Do not transport the console with its connector pod securing screws removed.
Do not attempt to remove the connector pod from the console. Do not obstruct
the ventilation slots. Allow adequate space around the console for air flow. If the
side trims are to be removed, do not refit their fixing screws to the unit. Retain
and store these in case the trims need to be refitted in the future.
8WZ316:2 and 12:2 User Guide
Connecting Power
EXTERNAL DC IN
RECOMMENDED ALLEN&HEATH POWER SUPPLY
REFER TO USER GUIDE FOR DET AILS
Read and understand the Important Safety Instructions printed at the start of this guide,
and the warnings printed on the rear of the console. Check that your local mains supply is
within the 100-240V operating voltage range allowed. Check that the correct mains lead
with moulded plug has been supplied with your console. Make sure that the IEC mains plug
is pressed fully into the panel socket before switching on.
Grounding
The connection to ground in an audio system is important for two reasons:
1. SAFETY - To protect the operator from high voltage electric shock, and
2. AUDIO PERFORMANCE - To minimise the effect of ground (earth) loops which result in
audible hum and buzz, and to shield the audio signals from interference.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR.
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIREREPLACE FUSE WITH SAME TYPE AND RATING.
ATTENTION: REMPLACER LE FUSIBLE AVEC UN DES MEMES CARACTERIS TIQUES.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ENGINEERED IN ENGLAND BY ALLEN & HEATH LIMITED
DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK
Serial No.
T630mA L 250V 20mm
FUSE
AC MAINS IN ~
100 - 240V~ 47-63Hz 45W MAX
WARNING: THIS APPARATUS MUST BE EARTHED
ON
OFF
0
I
For safety it is important that all equipment grounds are connected to mains ground so that
exposed metal parts are prevented from carrying high voltage which can injure or even kill
the operator. Do not disconnect the ground connection in the mains lead. It is
recommended that the system engineer check the continuity of the safety ground from all
points in the system including microphone bodies, turntable chassis, equipment cases, rack
metalwork and so on.
Switching the console on and off
It is good practice to turn power amplifiers off before switching the console and any other
connected equipment on or off. This prevents any unexpected clicks or thumps when the
equipment is powered up.
Turn amplifiers and powered speakers on last and off first.
To turn the console on, press the ON/OFF switch next to the IEC mains input socket. To
turn the console off, press this switch again.
Connecting a backup supply
A socket is included for plugging in an optional backup power supply. This provides the
reassurance of power supply dual redundancy, a feature usually found only in expensive top
end consoles. The console uses diode combining technology so that both supplies can be
powered at the same time. One will automatically take over should the other stop working.
The recommended backup supply for the MixWizard is the Allen & Heath MPS12 power unit.
Refer to the user guide which comes with this supply.
Only plug the recommended Allen & Heath power unit into this socket. Do not
attempt to modify any other power unit to work with the console. Do not attempt to modify or
extend the DC power cable that comes with the supply.
The console can work with just the internal supply powered by mains, or just the backup
supply, or with both powered at the same time. To ensure uninterrupted performance in the
unlikely event of a failure, we recommended that both supplies are powered.
WZ316:2 and 12:2 User Guide 9
13 GRP 4+
12 AUX 1+
11 AUX 2+
10 AUX 3+
9 AUX 4+
8 AUX 5+
7 AUX 6+
6 PFL+
5 AFL+
4 nc
3 PFL DC
2 AFL DC
14 GRP 3+
15 GRP 2+
16 GRP 1+
17 R+
18 L+
19 0V (CHS)
L- 37
R- 36
AUX 1- 31
GRP 4- 32
AUX 2- 30
GRP 3- 33
GRP 2- 34
GRP 1- 35
PFL- 25
AFL- 24
AUX 4- 28
AUX 5- 27
AUX 3- 29
AUX 6- 26
1 0V (PAFL)
nc 21
nc 23
nc 20
nc 22
10WZ316:2 and 12:2 User Guide
Audio Connections
The MixWizard uses professional grade 3 pin XLR and 1/4" TRS (3 pole) jack sockets. To
ensure best performance, we recommend that you use high quality audio cables and
connectors, and take time to check for reliable and accurate cable assembly. It is well
known that most audio system problems are due to faulty or sub standard interconnecting
leads. The following mating plugs may be used to connect audio signals to the console:
Avoid reversing + and - on balanced connections as this will result in reversed polarity (out
of phase) signals which may cause signal cancellation effects.
Where long cables runs are required, balanced interconnections should be used. However,
line level interconnections between more affordable 2-wire (signal, ground) unbalanced
equipment and the console are unlikely to cause problems if the cables are kept shorter than
10 meters or so. Refer to the wiring diagrams on the opposite page.
Dealing with Ground Loops, Buzz and Interference
For optimum performance all audio signals should be referenced to a solid, noise-free
ground (earth) point, frequently referred to as the ‘star point’ or ‘clean earth’.
A ground loop is created when potential differences exist between grounds at different
points in the system, and the signal has more than one path to ground. In most cases
ground loops do not result in audible problems. Should you experience hum or buzz caused
by a ground loop, check first that each piece of equipment has its own separate path to
ground. If so, operate ground lift switches on connected equipment in accordance with the
instruction manuals. Alternatively disconnect the cable screen at the destination end only.
This breaks the offending loop while keeping the signal shielding down the length of cable.
WARNING For operator safety do not remove the ground (earth) connection
in the power lead of the console or connected equipment.
To avoid interference pickup keep audio cables away from mains power units and cables,
thyristor dimmer units, computer equipment and mobile phones. Where this cannot be
avoided, cross the cables at right angles to minimise interference
A note about balanced connections
A differentially balanced connection has two signal wires, signal + (hot) and signal - (cold)
and a shield. The signal source generates positive going polarity down the + wire and
negative polarity down the – wire. The destination input stage accepts the + signal on its
non-inverting (+) input pin, but it inverts the – signal, adding it to the + signal. The result is
that the wanted signal is boosted. Now examine what happens when unwanted interference
(hum and noise) is induced into the cable. The noise is induced equally and with the same
polarity into both wires. At the destination input the – wire signal gets inverted and added to
the + signal. Because the polarity is the same on both input wires the noise cancels itself
out at this input. For this interference rejection to work it is important that the source, the
cable and the destination input are all balanced. Balancing provides greatest advantage
with low level signals such as those produced by microphones.
An impedance balanced
drive on the - wire. It does not generate a negative polarity signal at its – output. Instead,
the – wire has no signal but is held at the same impedance as the + wire. This means that
both wires pick up the noise equally resulting in cancellation as described above.
output provides similar interference rejection, but without the signal
WZ316:2 and 12:2 User Guide 11
ALLEN&HEATH
INSERT 16
LINE IN
INSERT 15
LINE IN
16
15
MIC
MIC
L
INSERT
R
L
INSERT
LINE IN
MIC
3
INSERT 8
LINE IN
8
MIC
16:2
7
INSERT
LINE IN
76
MIC
INSERT
LINE IN
6
INSERT 5
INSERT 4
INSERT 3
LINE IN
5
MIC
MIC
LINE IN
MIC
LINE IN
4
3
MIC
INSERT
LINE IN
2
INSERT 1
LINE IN
2
1
MIC
MIC
MixWizard WZ
14
INSERT
INSERT1312
INSERT 11
LINE IN
12
MIC
LINE IN
11
MIC
LINE IN
14
13
MIC
INSERT
LINE IN
10
MIC
10
9
INSERT
LINE IN
9
MIC
R
M
DIRECT
OUT
ABST2
A
B
SYS-LINK OUT ( option )
OUT
L
/MONO
R
A
OUT
INSERT RINSERT L
B
FX
+
L/M
ST5
EFFECT
R
1-16
DUAL
+
-
EFFECT
1-8
EFFECT
9-16
SYS-LINK OUT ( option )
EXTERNAL
AUX5
INTERNAL
AUX6
SINGLE
DIRECT
LRM
MIX
DIRECT
DIRECT
OUT
OUT
IN
L
/MONO
R
FX MUTE
FX EDIT
L
R
EXTERNAL
AUX5
INTERNAL
AUX6
FOOTSWITCH
MIDI IN
OUT
FX
+
L/M
-
ST1
+
R
-
SINGLE
EFFECT
1-16
EFFECT
1-8
DUAL
EFFECT
9-16
EXT FX
ST5
IN
L
/MONO
FX
R
ST6
IN
L
/MONO
R
DIRECT
DIRECT
OUT
OUT
46ST1 INAUX5AUXAUXAUXAUX 3AUX2SEND1
EXTERNAL DC IN
BACKUP SUPPLY
MIX
L
R
ONLY USE RECOMMENDED ALLEN&HEATH POWER SUPPLY.
REFER TO USER GUIDE FOR DETAILS.
9-1011-12
ST1 IN
ST3
IN
L
L
/MONO
/MONO
R
R
ST2
ST4
L
/MONO
R
IN
IN
L
/MONO
R
1 SEND2AUX3AUXAUXAUXAUX 5AUX 64
EXTERNAL DC IN
ONLY USE RECOMMENDED ALLEN&HEATH POWER SUPPLY
REFER TO USER GUIDE FOR DETAILS
DIRECT
MixWizard WZ312:2ALLEN&HEATH
LINE IN
MIC
DIRECT
OUT
8INSERT
8
OUT
8
DIRECT
OUT
DIRECT
OUT
910111213141516
FOOTSWITCHMIDI IN
RISK OF ELECTRIC SHOCK
AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR.
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE FUSE WITH SAME TYPE AND RATING.
ATTENTION: REMPLACER PAR UN FUSIBLE STRICTEMENT IDENTIQUE EN VALEURS.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
ENGINEERED IN ENGLAND BY ALLEN & HEATH LIMITED
7
INSERT
LINE IN
MIC
DIRECT
7
OUT
7
LINE IN
6
MIC
DIRECT
OUT
6
RISK OF ELECTRIC SHOCK
AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR.
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
ATTENTION: REMPLACER PAR UN FUSIBLE STRICTEMENT IDENTIQUE EN VALEURS.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCKDO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
ENGINEERED IN ENGLAND BY ALLEN & HEATH LIMITED
DIRECT
OUT
CAUTION
DO NOT OPEN
6INSERT
CAUTION
DO NOT OPEN
LINE IN
MIC
DIRECT
OUT
DIRECT
OUT
FX EDITFX MUTE
DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK
5INSERT
5
5
DIRECT
DIRECT
OUT
XLR OUT
2
1
3
- OUT
CONFORMS TO ANSI/UL STD. 60065
CERTIFIED TO CAN/CSA C22.2 No. 60065-03
MADE IN CHINA
Serial No.
4INSERT
LINE IN
4
MIC
DIRECT
OUT
4
XLR OUT
2
1
3
- OUT
CONFORMS TO ANSI/UL STD. 60065
CERTIFIED TO CAN/CSA C22.2 No. 60065-03
REPLACE FUSE WITH SAME TYPE AND RATING.
MADE IN CHINA
Serial No.
DIRECT
OUT
OUT
LINE IN/OUT
TIP +
+OUT
RING -
FUSE
T630mA L 250V 20mm
WARNING: THIS APPARATUS MUST BE EARTHED
3
LINE IN
3
MIC
DIRECT
OUT
3
LINE IN/OUT
TIP +
+OUT
RING -
FUSE
T630mA L 250V 20mm
WARNING: THIS APPARATUS MUST BE EARTHED
DIRECT
OUT
INSERT
SEND
TIP
RING
RETURN
AC MAINS IN ~
100 - 240V~ 47-63Hz 45W MAX
2INSERT
INSERT
LINE IN
2
MIC
DIRECT
OUT
2
INSERT
SEND
TIP
RING
RETURN
AC MAINS IN ~
100 - 240V~ 47-63Hz 45W MAX
DIRECT
OUT
12345678
INPUT
+IN
1
2
TIPTIP +IN
RINGRING -IN
MIC
- IN
3
LINE
ONI0OFF
1INSERT
LINE IN
1
MIC
DIRECT
OUT
1
INPUT
+IN
1
2
MIC
- IN
3
TIP +INTIP
LINE
RING -INRING
ONI0OFF
12WZ316:2 and 12:2 User Guide
The Console Connectors
INPUT
+IN
1
2
3
TIP +INTIP
RING -INRING
- IN
MIC
LINE
MIC / LINE IN The channel PAD (LINE) switch selects either the MIC
XLR or the LINE TRS jack as the input source. The XLR is normalled
through the TRS jack. This means that the XLR can be used for
microphone or line level signals when nothing is plugged into the jack
socket. Both inputs are balanced but can be wired to work with
unbalanced signals when required.
WARNING: Do not connect unbalanced sources or cables to
the XLR input when 48V phantom power is selected. To avoid loud
clicks always turn the channel off by pressing MUTE when switching
+48V on or off, and when plugging or unplugging cables.
STEREO LINE IN The WZ
channel inputs ST1,3 (unbalanced) and ST2,4 (balanced), and an
additional two stereo returns ST5 (balanced) and ST6 (unbalanced). The
WZ316:2 has two stereo return inputs ST1 (balanced) and ST2
(unbalanced). All inputs use TRS jacks. Unbalanced inputs automatically
connect the TRS ring to ground for working with balanced sources. The L
input is normalled through the R input to accept mono signals.
MIX
L
R
with the internal effects processor return. This means that an external
effects device fed from a different aux mix can mix with the internal
processor to save input channels. Alternatively, you could turn the internal
unit off and use the ST5 (ST1) input with an external unit only if preferred.
EFFECT
1-8
EFFECT
9-16
+
-
+
-
EXTERNAL
AUX5
INTERNAL
AUX6
L/M
ST5
R
SINGLE
EFFECT
Note that the ST5 (WZ
1-16
DUAL
3
12:2 has six stereo inputs comprising four
3
12:2) or ST1 (WZ316:2) stereo return input mixes
INSERT A single 3-pole TRS jack carries the unbalanced insert signal.
INSERT
SEND
RETURN
TIP
RING
Tip = send, Ring = return, Sleeve = common ground. The channel insert
is post-HPF, pre-EQ and operates at 0dBu. The LR mix insert is pre-fader
and operates at -2dBu. These should work fine with line level signal
processing equipment such as compressors, outboard EQ, delay units and
so on. An example of a suitable cable is shown here:
DIRECT OUTPUT The mic/line channel direct output is available on
an impedance balanced TRS jack. It is a line level signal operating at
0dBu. The source is set using an internal option jumper for each channel.
The factory default setting is pre-fade (following the pre/post-EQ setting).
This may be changed to post-fade if preferred.
The direct outputs provide a useful source for multitrack recording. Many
users prefer pre-fade sends for this application so that the live show fader
movements do not affect the recording which can be mixed later. Another
application is channel effects sends. For example, a reverb unit may be
dedicated to work with the lead vocalist channel only. Using a post-fade
direct output instead of an aux send frees up that aux mix for other
purposes.
WZ316:2 and 12:2 User Guide 13
L, R, M OUT The main console mix outputs are on balanced XLR.
These produce +4dBu when the meters read ‘0’. The M output can be
switched to provide a mono sum of the post-fade L and R signals, or the
AUX6 output.
The L and R outputs typically feed the house PA system in live sound
mixing, or a 2-track recorder in studio mixing. In mono mode, the M output
can provide an additional feed for a mono fill speaker or zone, or be used
as the main feed into a mono PA. Used with a mono PA the L and R mix
can provide a pair of subgroups, each with routing using the channel PAN
controls, inserts and faders. Configured to provide the AUX6 mix, the M
output is ideal for driving a sub bass speaker system when working with
an ‘aux fed subs’ PA. This provides the sub feed with its own per-channel
mix on balanced XLR and with dedicated fader alongside the main LR
faders for proper control of the house volume.
AB OUT A pair of impedance balanced TRS jacks can be configured to
provide an additional LR mix or engineers monitor send. These operate at
-2dBu line level. A front panel recessed ‘mode’ switch determines the
source to the AB output. This may be set to follow the console monitor
system and therefore feed an independent local stereo monitor or even
engineers wedge speaker. When set to follow the LR mix, the factory
default source is taken post LR fader. An internal option jumper is
available to change this to pre LR fader.
The unique AB output feature provides the MixWizard with a host of
possibilities… independent 2-track recording feed, broadcast feed, zone
and delay fill feeds, local monitor, engineers wedge monitor and more.
AUX OUT 1-6 Each aux send is available on an impedance balanced
TRS jack operating at -2dBu line level. An internal option is available to fit
a balanced line driver IC to provide an electronically balanced output
operating at +4dBu. Note that it is not usual to require this option as the
impedance balanced standard drive provides significant interference
rejection when feeding balanced equipment inputs.
The aux sends are typically used to feed stage monitors, effects devices
such as reverb and delay, and for special mix requirements.
MIDI IN A standard 5-pin DIN MIDI input socket is provided. This is
used with external MIDI equipment or a MIDI equipped PC to control the
built-in effects processor. Free software can be downloaded from the
Allen & Heath web site for PC editing of the parameters via MIDI.
FOOTSWITCH Mutes and unmutes the ST5 (ST1) effects return
channel, ideal for bypassing the effects between songs. Note that this
affects the internal processor and also any external effects device that
may be plugged in to these return inputs. Use a momentary or latching
footswitch as required. Shorting a TS or TRS jack tip to sleeve turns the
mute on.
SYS-LINK II OPTION A blank plate is fitted here as standard. The
Sys-Link II option kit is available from Allen & Heath. Refer to OPTIONS
later in this guide.
14WZ316:2 and 12:2 User Guide
The MONO Input Channel
GAIN
HM
LM
LF
AUX
AUX
AUX
AUX
AUX
AUX
PAN
- 10 10
HF
700
1
2
3
4
5
6
PK!
SIG
0
20
-15
1k
500Hz
-15
70
45
35Hz
-15
-15
PRE
POST
10
5
0
5
10
20
30
OO
+48V
PAD
(LINE)
30
HPF
3k
180
OO+6
OO+6
OO+6
OO+6
OO+6
OO
=
LR
PFL
60 40
+15
15k
+15
+15
+15
+6
MUTE
+48V Switches +48VDC to the channel input XLR for powering
microphones or DI boxes that need phantom power. The power is
current limited through 6k8 ohm resistors to pins 2 and 3.
40
50
WARNING: Do not connect unbalanced sources or cables
to inputs with phantom power selected. To avoid loud clicks
always mute the channel before switching +48V on or off and
when plugging or unplugging microphones.
4k
6k
PAD (LINE) Press this switch to select the channel TRS jack LINE
250
400
1k
input. Release the switch to select the XLR MIC
normals through the TRS socket. With nothing plugged into the line
input the switch therefore becomes a PAD for the mic XLR. It
attenuates the input signal by 20dB for connection to high level
microphone or line sources.
input. The XLR
GAIN Adjusts the input sensitivity to match the connected source to
the internal 0dBu operating level of the channel. Provides a variable
50dB range from +10 to +60dB gain (mic), or -10 to +40dB (line, pad
selected). The gain should be set using PFL so that the console
meters average ‘0’ with loudest moments lighting ‘+6’. Reduce gain if
the red peak indicator lights.
HPF Switches in the channel high pass filter. This attenuates
frequencies below 80Hz by 12dB per octave. The filter is pre-insert,
pre-EQ. Select the HPF to reduce low frequency noise such as
POST
PRE
microphone popping, stage noise and tape transport rumble.
EQ A 4-band semi parametric EQ provides independent control of
four frequency bands. HF and LF are shelving filters which affect high
frequencies above 12kHz, and low frequencies below 80Hz
respectively. HM and LM are bell shaped peak/dip filters which affect
frequencies around a centre point which can be swept from 500Hz to
15kHz and 35Hz to 1kHz respectively. These have a width (Q) of 1.8.
All bands can be boosted or cut by up to 15dB and have a centre
detent 0dB position.
Check for the best microphone selection and placement before using
the EQ. Start with the EQ set flat and apply only as much boost or cut
as is really needed. When dealing with problem frequencies cut rather
than boost where possible.
+20
+15
+10
+5
0dB
-5
-10
-15
-20
2050 100 200500 1k 2k5k 10k 20k
+5
0dB
-5
-10
-15
-20
-25
-30
-35
-40
+20
+15
+10
+5
0dB
-5
-10
-15
-20
2050 100 200500 1k 2k5k 10k 20k
+20
+15
+10
+5
0dB
-5
-10
-15
-20
10k5k2k1k500200100502010
20k10k5k2k1k5002001005020
WZ316:2 and 12:2 User Guide 15
GAIN
HM
LM
LF
AUX
AUX
AUX
AUX
AUX
AUX
PAN
- 10 10
HF
700
1
2
3
4
5
6
PK!
SIG
0
20
-15
1k
500Hz
-15
70
45
35Hz
-15
-15
PRE
POST
10
5
0
5
10
+48V
PAD
(LINE)
30
HPF
3k
180
OO+6
OO+6
OO+6
OO+6
OO+6
OO
=
LR
PFL
60 40
+15
15k
+15
+15
+15
+6
MUTE
AUX SENDS These rotary controls adjust how much channel
signal is mixed to the aux outputs. Each of the 6 auxes has its own
control. They adjusts from fully off to +6dB boost. Unity gain 0dB is
marked at 3 o’clock position. Factory default settings should satisfy
the most common applications:
40
50
AUX1, AUX2 = Pre-fade
AUX3, AUX4 = Switched pre/post using PRE swittch
AUX5, AUX6 = Post-fade
Pre-fade aux = Pre-INSERT, pre-EQ, post-MUTE
4k
6k
These settings may be changed if preferred by repositioning internal
jumper link options. They offer many different combinations of pre and
post-fade sends, and a post-EQ option for the pre-fade sends. The
PRE switch can be assigned to one, two or more of the sends. More
250
400
1k
detail is provided in OPTIONS later in this guide.
Pre-fade aux sends are not affected by the channel fader movements.
These are typically used to feed stage monitors. In most cases users
also prefer that the monitor sends are not affected by inserted
processors or the channel EQ. Post-fade aux sends follow the channel
faders and are typically used to send a proportion of the channel signal
to an effects device such as reverb or delay. Pre or post-fade sends
may also be used for special applications such as recording, zone
feeds, clean feeds and aux fed subs.
PRE When pressed the pre-fade channel signal is sent to the
associated auxes. When released the post-fade signal is sent. Auxes
3 and 4 are affected by the PRE switch (factory default). You can
change this by repositioning the internal option jumpers.
POST
PRE
PAN Positions the channel signal between L and R in the stereo
mix. The centre position (mono image) is detented for quick resetting.
MUTE When pressed the channel signal is turned off. This affects
the feed to the LR mix, pre and post-fade aux sends and direct output,
but does not affect the insert send. The red indicator lights when the
channel is muted.
PFL Press PFL to listen to the pre-fade channel signal in the
headphones or AB monitor (if configured) without affecting the main
outputs. The console main LR meters are interrupted with the channel
signal. The red PK indicator half lights to show that PFL has been
selected on that channel. Selecting more than one PFL at the same
time mixes those signals together in the monitor.
PEAK The red indicator illuminates when the channel pre-fade
signal is within 5dB of clipping. This gives you enough warning to
reduce the GAIN control before you hear signal distortion.
SIGNAL The green signal presence indicator lights when the
channel pre-fade signal is greater than -12dBu.
20
FADER Controls the channel level feeding the main LR mix and
post-fade aux sends. It also affects the direct output if this has been
set to post-fade using the internal option jumpers. The fader provides
30
OO
+10dB maximum boost above its normal unity gain 0dB position.
Important note on setting channel levels: Use PFL to set the GAIN
controls for correct signal level through each channel. Use the faders
to balance each signal in the mix. These are typically operated around
their -20 to 0 positions according to the mix. We do not
recommend
setting the faders to ‘0’ and mixing using the GAIN controls.
16WZ316:2 and 12:2 User Guide
The STEREO Input Channel ( WZ
3
12:2 only)
0
-5
5
GAIN
-10
10
-20
16
O
O
ON
TO
LR
TO
(ST3+ST4)
11-12
0
-5
5
GAIN
-10
10
-20
16
O
O
ON
HF
+15
-15
HM
+15
-15
LM
+15
-15
LF
+15
-15
PRE
AUX
1
+6OO
AUX
2
+6OO
AUX
3
+6OO
AUX
4
+6OO
POST
PRE
AUX
5
+6OO
AUX
6
+6
OO
POST
=
BAL
Dual stereo inputs Each of the two stereo channels has two
stereo inputs which can be used separately, mixed together or split so
that one feeds the channel, the other routes direct to LR. For example,
you could mix two sound effects playback devices or two reverb
returns together into one channel. This can be useful in saving
channels, letting you mix many inputs in a small space. The L input
signal normals through the R input socket so that a mono source may
be plugged in to feed both left and right sides of the stereo channel.
ST1, ST3 Unbalanced TRS inputs. The GAIN control adjusts from
fully off to +16dB gain. Press the ST1 (ST3) switch to turn the input
on.
Routing mode switch Recessed switch to prevent accidental
operation. In the normal up position the ST1 (ST3) signal mixes with
ST2 (ST4) into the stereo channel. When pressed the signal is routed
direct to the LR mix instead of the channel. This lets you use these
inputs as simple stereo returns in addition to the full stereo channels,
providing four independent stereo sources to the LR mix.
ST2, ST4 Balanced TRS inputs. The GAIN control adjusts from
fully off to +16dB gain. Press the ST2 (ST4) switch to turn the input
on. These inputs always feed the stereo channels.
EQ A 4-band fixed frequency EQ provides independent control of
four frequency bands. HF and LF are shelving filters which affect high
frequencies above 12kHz, and low frequencies below 80Hz
respectively. HM and LM are bell shaped peak/dip filters which affect
frequencies centred around 2.5kHz and 250Hz respectively. These
have a width (Q) of 1.8. All bands can be boosted or cut by up to 15dB
and have a centre detented 0dB position.
AUX SENDS These work as described for the mono channel. The
L and R sides of the stereo signal sum together to feed each aux in
mono. This can be changed using an internal jumper option so that L
feeds auxes 1,3 and R feeds auxes 2,4.
RL
MUTE
PK!
PFL
SIG
10
5
BAL Balances the level of the L signal against the R signal to
compensate for differences in the source signal, or to position the
signal within the stereo image. The centre equal level position is
detented for quick resetting.
MUTE When pressed the channel signal is turned off. This affects
the feed to the LR mix, and pre and post-fade aux sends. The red
0
5
10
indicator lights when the channel is muted.
PFL Press PFL to listen to the summed L+R pre-fade channel signal
in the headphones or AB monitor (if configured) without affecting the
main outputs. The console main LR meters are interrupted with the
20
channel signal. The red PK indicator half lights to show that PFL has
been selected on that channel.
30
OO
PEAK The red indicator illuminates when the channel pre-fade
signal is within 5dB of clipping. This gives you enough warning to
reduce the GAIN control before you hear signal distortion.
SIGNAL The green signal presence indicator lights when the
channel pre-fade signal is greater than -12dBu.
WZ316:2 and 12:2 User Guide 17
EXTERNAL
AUX5
INTERNAL
AUX6
The Stereo Effects Channel Console serial number starting W31222, W31622
3
16:2 and WZ312:2 feature a built-in stereo digital
SINGLE
Vocal Plate
1
Slap Reverb
2
Classic Plate
3
Bright Plate
4
Perc Plate
5
Large Room
6
Hall+Stage
7
Concert Hall
8
St Chorus
9
Amb Flanger
10
11
St Doubler
2 Tap Delay
12
Slap Delay
13
14
Vocal Delay
St Delay
15
Karaoke
16
1
Vocal Plate
2
Slap Reverb
3
Classic Plate
4
Bright Plate
5
Perc Plate
6
Large Room
7
Hall+Stage
8
Concert Hall
9
St Chorus
Amb Flanger
10
11
St Doubler
12
2 Tap Delay
Slap Delay
13
Vocal Plate
14
15
Classic Plate
16
Concert Hall
SINGLE
FX
DUAL
L/M
ST5
R
EFFECT
1-16
DUAL
FX
EFFECT
EFFECT
AUX
1
AUX
2
AUX
3
AUX
4
ST5
LEV
AUX
1
AUX
2
AUX
3
AUX
4
AUX
5
AUX
6
1-8
9-16
+6OO
+6OO
+6OO
+6
OO
9
1
10
2
11
3
124
13
5
14
6
157
816
BANK
SEL
/ FX
+6OO
MUTE
PRE
+4OO
+4OO
+4OO
+4OO
+4OO
+4OO
SINGLE FX
DUAL FX
AUX5 = 1-8
AUX6 = 9-16
AUX5 = 1-16
+
-
+
-
MIX
The MixWizard WZ
effects processor. This can be configured to work as a single 16
preset effects engine fed from AUX5, or in dual mode as two 8 preset
effects engines independently fed from AUX5 and AUX6. The
processed signal is routed back to the mix through the ST1 (ST5)
stereo return channel. In dual mode the two stereo effects mix
together into the return channel. The ST1 (ST5) TRS jack inputs mix
with the internal effects processor through the return channel. This
allows you to have the internal and external effects devices returning
their processed signals through one return channel. In dual mode this
gives you three stereo signals mixing into one.
AUX SENDS The combined effects signal can be returned to
Auxes 1 to 4. These sends are not affected by the ST1 (ST5) LEV
control which returns the signal to the LR mix. The stereo signal is
summed to feed the auxes in mono. This can be changed if preferred
by repositioning internal jumper options so that L feeds auxes 1,3, and
R feeds auxes 2,4. Use the aux sends to add the effects to the
monitors if required.
Selecting the effects preset Press SEL to scroll down
through the available effects. The green indicator lights to show which
effect is active. Press BANK to change between preset 1-8 and preset
9-16. The red indicator lights to show presets 9-16 are selected. In
dual mode BANK toggles between the AUX5 and AUX6 effects
processor selections. The default preset names are printed on the
front panel for reference. Presets can be edited using PC software.
Turning off the internal effects Once you have scrolled
through all 16 effects the green indicator turns off showing that the
internal processor is disabled. Select this mode if you want to work
with external effects sent from aux 5 or 6.
ST1 (ST5) LEV Returns the combined stereo effects to the main
LR mix. Adjust from fully off to +6dB maximum boost. Normal 3
0’clock 0dB operating position is marked on the panel.
MUTE Press this switch to mute the stereo return channel. This
turns off the feed to the LR mix and the auxes. The channel may also
be muted using a footswitch plugged into the rear of the console. The
red indicator lights when the channel is muted by the MUTE switch
and/or the footswitch. Note that the MUTE switch is latching. This
means the channel shall remain muted as long as the switch is in its
pressed position regardless of the footswitch.
MODE Recessed switch to prevent accidental operation. Situated
below the AUX6 master level control. Use a pen or sharp object to
change the setting. In the normal up position the processor is
configured as a SINGLE effects unit driven by AUX5. In the pressed
position the processor is configured as a DUAL effects unit driven by
AUX5 and AUX6.
L
Resetting the effects presets To restore the factory default
R
presets hold down the SEL key while powering up the console. Make
sure you do this while the amplifiers are turned off. The 8 green
indicators flash in sequence followed by the BANK indicator flashing on
then off to confirm the reset.
Note: For information on using MIDI and the free WZ Effects Editor software refer to www.allen-heath.com.
18WZ316:2 and 12:2 User Guide
The Master Section
PRE
AUX
1
+4OO
AUX
2
+4OO
AUX
3
+4OO
AUX
4
+4OO
AUX
5
+4OO
AUX
6
+4OO
SINGLE FX
DUAL FX
AUX5 = 1-8
AUX6 = 9-16
AUX5 = 1-16
AUX 1
1-2
AUX 2
AUX 3
3-4
AUX 4
AUX 5
5-6
AUX 6
/ FX
ST5
ST6
M
ALL UP = LR
ALT LR OUT
MONITOR
AB
0
+10
OO
L+R
AUX 6
RL
M
AUX MASTERS
adjusts the output level to match external equipment, or to trim the
monitor, effect or other send without affecting the mix balance. Up to
+4dB boost is available above the normal 0dB position.
Note that the AUX5 and AUX6 master controls do not affect the level
sent to the internal effects processor. They do affect the level
available at the rear panel aux output sockets.
Each aux mix has a master level control that
LR FADER MASTERS Individual 100mm faders adjust the main
L-R mix level. They provide +10dB boost above the nominal ‘0’
position. For best performance the faders should be operated around
the ‘0’ position for normal ‘loud’ level. If you find yourself operating
significantly below ‘0’ then the amplifier or other destination equipment
is too sensitive for the console +4dBu output. Simply turn down the
amplifier or equipment level trim. If none is available then insert an
attenuator pad between the console and connected equipment.
Operating the faders well below ‘0’ may degrade the noise
performance of the equipment.
10
5
10
5
M FADER MASTER A recessed mode switch above the M fader
selects the fader source.
0
5
10
0
5
10
Mono master To use the M output as an L+R summed mono feed
then select the up position. The fader can become the master level
controller for a mono PA, mono fill or delay speaker, additional zone,
mono recording and so on.
20
20
Aux master To use the M output as the AUX6 master press the
switch using a pen or pointed object. Use the post-fade AUX6 channel
sends to mix the required signals to the M output. This provides a
30
30
OOOO
main console output with its own mix bus. Typical applications include:
Dedicated MONO mix The output feeds a centre mono fill speaker
system, for example above the proscenium arch or along the front of
the stage in a theatre. You may wish to feed just a few of the sources
AUX6
to these speakers, for example just the radio mic channels for front row
clarity. Using the aux send allows you to create the required mix
balance and have proper master fader control.
Aux fed subs This increasingly popular application drives the sub
bass speakers with their own mix. It lets you send only those sources
with wanted low frequency information to the sub speakers. It can
dramatically clean up the mix as non-bass channels such as vocals
and guitars are kept out of the subs and therefore do not allow low
frequency pickup to muddy the mix. It is typical to include only sources
such as kick drum, bass guitar, keyboards and sound effects to these
speakers.
The unique MixWizard aux mode feature puts the master control of the
sub mix on to a fader next to the main LR faders. This means that the
house volume can be controlled without upsetting the balance between
LR and sub speakers. The feed to the sub speaker system is on
balanced XLR, and it can be monitored by selecting the M switch in the
headphones monitor section.
WZ316:2 and 12:2 User Guide 19
AB OUTPUT This is an additional stereo output that can be
configured as a separately controlled mix output or a local loudspeaker
monitor send. A recessed mode switch above the AB level control
selects the source. Use a pen or pointed object to change the setting.
PHONES
OO
0
TO LR
+16
+9
+6
+3
0
-3
-6
-9
-12
-16
-20
-30
R
L
PFL
PHONES
10
0
AUX 1
1-2
AUX 2
Adjust the output level from fully off to a maximum +10dB boost. The
normal 0dB position is marked on the panel.
With the mode switch in its up position, the LR mix is selected as the
source to the AB output TRS jacks. Factory default setting is post-LR
fader. If preferred you can change this to pre-LR fader by repositioning
internal option jumpers so that the LR master fader movements do not
affect the output. In LR mode the AB output provides an additional
main mix output ideal for independent fill speaker control, 2-track
recording or broadcast feed and so on.
With the mode switch pressed, the console monitor system is selected
as the source. You can use this to feed local monitor speakers to
listen to the source selected on the monitor switch bank interrupted by
PFL. Local speaker monitoring can be useful in theatre and stage
monitoring applications.
Console Monitor Comprehensive engineer’s headphones monitoring
is provided. Select the source to listen to using the monitor switch
bank. With no switch pressed the post-fade LR mix is monitored.
Press M to listen to the post-fade M source. Pressing any switch
higher up the bank overrides the previous selection. Pressing ST1
(ST5) listens to the wet effects only return signal if the internal effects
processor is active. Pressing Aux pairs 1-2, 3-4, 5-6 together listens to
the two selected auxes as a stereo pair. The two console meters
display the selected monitor source signal level.
AUX 3
3-4
AUX 4
AUX 5
5-6
AUX 6
ST5
/ FX
ST6
Pressing channel PFL switches automatically overrides the current
monitor selection with the pre-fade signal from that channel or
selection of channels. The red PFL active indicator lights and the
console meters display the channel signal.
We recommend you use closed ear headphones in the range 30 to
600 ohms designed for live sound monitoring. Headphones around
100 ohms impedance are a popular choice.
WARNING: To avoid damage to your hearing do not operate
any close-to-ear monitoring such as headphones for long periods
M
ALL UP = LR
ALT LR OUT
MONITOR
0
AB
at high volume. Continued exposure to high volume sound can
cause frequency selective or wide range hearing loss.
ST2 (ST6) RETURN This is a simple stereo return channel that
+10OO
routes to the main LR mix. The typical application is to plug in a CD or
similar playback device for walk-in or background music. It can also be
used as an additional effects return. Adjust the volume using the LEV
control. Route the signal to LR by pressing the TO LR switch. The
green LED lights to warn that the source is routed to LR.
You can use the ST2 (ST6) input to monitor your 2-track recording.
Press the ST2 (ST6) monitor source select switch. Use the AB output
to feed your recorder. If you are monitoring while mixing live, make
sure you do not accidentally press the TO LR switch and route your
recording to the house speakers.
20WZ316:2 and 12:2 User Guide
Gain Structure
How the levels between the different signal stages are set up is referred to as the
gain structure
signals are matched to the ‘normal operating level’ of the console. Similarly the
levels of the connected amplifiers and destination equipment should be correctly
matched to the console outputs. If set too high then the signal peaks will be
clipped resulting in distortion, and if set too low then the signal-to-noise
performance will be degraded resulting in excessive background hiss and noise.
. For best performance it is important that the connected source
Using the Meters The MixWizard provides metering of inputs and outputs.
For best results operate the console with the main meters averaging around ‘0’
allowing the loudest moments to reach ‘+6’. Reduce the channel gain settings if
the red peak indicators start to flash. Note that the peak indicators light 5dB
before actual clipping to warn that you are nearing distortion and should reduce
gain. The LED bar meters have a ‘quasi-peak’ response with fast attack and slow
release so that fast musical transients are accurately displayed.
Matching a Source to the Console Start by turning down the channel
fader and send levels to prevent unexpected loud volumes reaching the main
speakers and monitors. Using PFL, adjust the GAIN control for an average ‘0’
reading on the console meters. These automatically switch to show the channel
pre-fade signal when PFL is pressed. Listen to the signal using headphones or
local AB monitor. Once the channel gain is correctly set you can raise the levels
to bring the channel into the mix. Note that you may need to adjust the gain if you
make significant changes to the EQ. Make sure that any equipment inserted into
the channel is set to operate around 0dBu line level. First set the gain with
inserted signal processors such as compressors switched to bypass.
Matching the Console to Destination Equipment The console
produces a standard XLR output level of +4dBu for a meter reading of ‘0’. It can
produce a maximum of +26dBu which is more than is usually required and
therefore gives you plenty of headroom. If you are connecting to a sensitive
power amplifier it is advisable to turn down its input trim control if the normal
console level is too high. Simply turning down the console output faders
degrades the output stage noise performance and reduces the resolution of the
fader movement. The output faders are best operated around ‘-10’ to ‘0’ for
loudest average volume required. This allows additional headroom if you need it.
Terminology The normal operating level is the optimum signal level for best
console performance, indicated by ‘0’ meter readings and resulting in the +4dBu
XLR output level. The channels operate at 0dBu and the mix stages at –2dBu for
extended headroom. Headroom
for loud peaks before the signal becomes clipped
The signal-to-noise ratio
level and residual noise floor
dynamic range
signal range possible from quietest to loudest.
is the sum of headroom and SNR representing the maximum
(SNR) is the difference measured in dB between normal
is the extra level available above normal to allow
resulting in audible distortion.
(hiss) produced by the console electronics. The
Final word… A little care with setting gain structure throughout the signal
chain will give you the best performance and most manageable control of the mix.
WZ316:2 and 12:2 User Guide 21
Specifications
Performance
Maximum output level XLR +26dBu into 600 ohms max load
Jack +21dBu into 2k ohm max load
Internal headroom Channels +21dB
Mix +23dB
Meters 3 colour LED, quasi peak response
Sensitivity 0VU = +4dBu at XLR output
Master meters 12 segment -30 to +16dB
Channel meters 2 segment -12, +16dB (5dB before clip)
Frequency response 20Hz to 50kHz +/-0.5dB
THD+n at +10dBu 1kHz Channel to mix out < 0.004%
Crosstalk at 1kHz Fader shutoff >90dB
Channel mute >100dB
Inter channel >90dB
Noise, rms 22Hz to 22kHz Mic EIN -128dB
Residual output noise < -95dBu (-99dB S/N)
LR unity fader mix noise < -83dBu (-87dB S/N)
Power supply Internal 100-240V, 50/60Hz auto sensing, IEC input
External Input for optional MPS12 backup supply
Power consumption 45W max
Mains fuse T630mA L 20mm
Mechanical
Free standing dimensions W 507 (20”) x D 530 (20.9”) x H 194 (7.7”)
Rack mounted W 483 (19”) x D 122 (4.8”) x H 444 (17.5”) 10U
Underside connectors
Rack mounted W 483 (19”) x D 193 (7.6”) x H 497 (19.6”) 11.2U
Rear connectors
Weight 10kg (22lbs)
22WZ316:2 and 12:2 User Guide
Connections
Mono channel XLR balanced pin 2 hot Sensitivity -60 to +10dBu
TRS balanced, tip hot Sensitivity -40 to +10dBu
Pad out (MIC) 2k ohm
Pad in (MIC or LINE) >10k ohm, -20dB
Max input level +30dBu
XLR phantom power +48V, on/off
Stereo channel ST1,3 TRS unbalanced >10k ohm, -16 to +20dBu
ST2,4 TRS balanced >10k ohm, -16 to +20dBu
Stereo returns ST1(5) TRS balanced >10k ohm, -6 to +20dBu
ST2(6) TRS unbalanced >2k ohm, -2 to +20dBu
Inserts Channel TRS, tip send, ring return, 0dBu
Output TRS, tip send, ring return, -2dBu
L, R, M outputs XLR balanced pin 2 hot <75 ohm, +4dBu, +26dBu max
Aux 1-6 output TRS impedance balanced <75 ohm, -2dBu, +21dBu max
Electronic balance option <75 ohm, +4dBu, +26dBu max
Direct out TRS impedance balanced <75 ohm, 0dBu, +21dBu max
AB out TRS impedance balanced <75 ohm, -2dBu, +21dBu max
Headphones TRS, tip L, ring R, 30 to 600 ohm headphones recommended
Lamp 4-pin XLR max 12V 5W lamp
MixWizard 3 Series Part Numbers
3
WZ
12:2 8 mic/line, 2 dual stereo, LR console W31222/v
3
WZ
16:2 16 mic/line LR console W31622/v
3
WZ
14:4:2 10 mic/line, 2 dual stereo, 4 group console W31442/v
3
WZ
12:2 and WZ316:2 Sys-Link II output option kit W312/16-SLV2
3
WZ
14:4:2 Sys-Link II input/output option kit W31442-SLV2
SSM2142P balanced output driver option IC AE0302
DRV134 balanced output driver option IC (alternative to above) AE5725
Allen & Heath MPS12 backup power supply option MPS12/v
Allen & Heath 18” gooseneck LED lamp LEDLAMP
WZ316:2 and 12:2 User Guide 23
WZ316:2
WZ3 16:2
MIC
BALANCED
LINE
INSER T
0dBu
MIC/LINE INPUTS
2= +
TIP= +
AUX 5
AUX 6
48V
GAIN
LINE (PAD)
-20dB
+
-
TIP= SEND
RING= RETURN
DIRECT OUT
0dBu
IMPEDANCE BALANCED
EFFECTS
MODE
SINGLE
DUAL
MIDI PARAMETER EDIT
PHANTOM POWER
HPF
TIP= +
RING= -
EFFECT
1-16
4 BAND EQUALISER
HF
HM
LM
LF
ST1 IN (EXT EFFECTS IN)
L/M
R
EFFECT
1-8
EFFECT
9-16
FOOTSWITCH
PK
SIG
PFL
FADER
POST-EQ
P = PRE-FADE
S = SWITCHED
A = POST-FADE
B
A
AUX
PRE-FADE
POST-FADE
PRE-INSERT, PRE-EQ
C
D
STEREO RETURN 1
+
-
BALANCED 0dBu
+
SUM
+
+
ST2 IN
L/M
UNBALANCED -2dBu
R
MUTE
PRE
HGJUMPEREF
P S
P
S
1
2
MUTE
SUM
+
MS
JP1
MONO/STEREO AUX SOURCE
A S
3
4
FROM AUX5,6
TO MONITOR
STEREO RETURN 2
TO MONITOR
ST2 TO LR
5
PAN
LKJI
A
LR
AUX1
AUX2
AUX3
AUX4
LR
SYS-LINK CONNECTION
AUX 1-6
PFL
LEFT
RIGHT
SL
AUX SENDS 1-6
SL
AUX1
STEREO 1-2
AUX2
AUX3
STEREO 3-4
AUX4
AUX5
STEREO 5-6
AUX6
ST1 (EFFECTS)
ST2
M
ALL UP= L-R
MASTER
AUX1-6 TO MONITOR
MONITOR
L-R
POST-FADE
PRE-FADE
INSE RT
-2dBu
INSE RT
-2dBu
MONO SUM
AUX6
AUX OUT
TIP= +
+4dBu BAL OPTION
L
R
PFL
ACTIVE
MONITOR METERS
MONITOR
LEV
A-B
LEV
A-B
-2dBu IMP EDANCE BALA NCED
L FADER
R FADER
+
SUM
M FADER
-2dBu
IMPEDAN CE BALANCED
HEADPHONES
L
R
A OUT
TIP= +
B OUT
TIP= +
BAL
L-R
BAL
M
BAL
LEFT OUT
2 = +
RIGHT OUT
2 = +
M OUT
2 = +
+4dBu
+4dBu
+4dBu
SL
AUX MIX
AUX 5,6 TO F X, AUX6 TO C
PFL DC
PFL MIX
SL
S
6
MONITOR SELECT
SL
L MIX
SL
R MIX
FROM AUX6
24WZ316:2 and 12:2 User Guide
WZ312:2
WZ3 12:2
MIC
2= +
TIP= +BALANCED
LINE
INSERT
0dBu
MIC/LINE INPUTS
L/M
INPUT ST1(3)
R
+
L/M
INPUT ST2(4)
-
+
R
-
DUAL STEREO INPUTS
48V
GAIN
LINE (PAD)
-20dB
TIP= SEND
RING= RETURN
DIRECT OUT
0dBu
IMPEDANCE BALANCED
GAIN
GAIN
PHANTOM POWER
HPF
+
-
TIP= +
RING= -
ON
ON
SYS-LINK CONNECTION
RIGHT
LEFT
PFL
AUX 1-6
4 BAND EQUALISER
HF
HM
LM
LF
PRE-FADE
POST-FADE
CH
LR
4 BAND EQUALISER
HF
HM
+
LM
LF
PRE-INSERT, PRE-EQ
C
D
PK
SIG
SUM
P = PRE-FADE
S = SWITCHED
A = POST-FADE
PK
SIG
PFL
MUTE
FADER
POST-EQ
B
A
FEJUMPERGH
S
P
1
AUX
P = PRE-FADE
S = SWITCHED
A = POST-FADE
PFL
+
MUTE
PRE-FADEPOST-FADE
MSMS
CN4
MONO/STEREO AUX
BADCFEHGJ ILKJUMPER OPTIONS
P
AUX
1
PRE
2
FADER
PRE
P SPPS2S
3
AUX SENDS 1-6
SL
SL
AUX1
STEREO 1-2
AUX2
AUX3
STEREO 3-4
AUX4
AUX5
STEREO 5-6
AUX6
ST5 (EFFECTS)
ST6
M
ALL UP= L-R
PRE
R
SL
SL
MASTER
AUX1-6 TO MONITOR
MONITOR
L-R
POST-FADE
LRL
INSERT
-2dBu
INSERT
-2dBu
A-B
LEV
PFL
ACTIVE
L
L FADER
+4dBu BAL OPTION
R
MONITOR METERS
LEV
A-B
R FADER
-2dBu IMPEDANCE BALANCED
SL
PAN
IJKL
S
SA
A
6
5
4SP3
PAN
++
CN5
SAA4S5S
6
AUX MIX
AUX5,6 TO FX, AUX 6 TO C
PFL DC
PFL MIX
MONITOR SELECT
L MIX
R MIX
SL
IMPEDANCE BALANCED
MONITOR
A OUT
TIP= +
B OUT
TIP= +
BAL
BAL
AUX OUT
TIP= +
-2dBu
HEADPHONES
L
R
2 = +
L-R
2 = +
LEFT OUT
+4dBu
RIGHT OUT
+4dBu
FROM AUX5,6
TO MONITOR
LR
AUX1
AUX2
AUX3
AUX4
ST2 TO LR
TO MONITOR
LR
STEREO RETURN
MODE
SINGLE
AUX 5
AUX 6
DUAL
MIDI PARAMETER EDIT
EFFECTS
EFFECT
1-16
ST6 IN (EXT E FFECTS IN)
L/M
R
EFFECT
1-8
EFFECT
9-16
STEREO RETURN
+
-
BALANCED 0dBu
+
-
+
FOOTSWITCH
SUM
+
MONO/STEREO AUX SOURCE
ST6 IN
L/M
R
MUTE
SUM
+
SM
JP1
UNBALANCED -2dBu
WZ316:2 and 12:2 User Guide 25
FROM AUX6
+
MONO SUM
AUX6
SUM
M FADER
M
BAL
M OUT
2 = +
+4dBu
User Options
REMOVE 4x M4 POZI SCREWS PER SIDE
REMOVE SIDE TRIMS
REMOVE M4 POZI SCREW PER SIDE
ROTATE POD
REMOVE 3x M3 TORX SCREWS
ROTATE POD
REMOVE 4x M3 TORX SCREWS
The MixWizard has a versatile architecture which
should satisfy most applications you may encounter
without modification. However, the following internal
options provide alternative settings for those
applications that may demand them. Access is
required to the internal assemblies. For user
convenience, pluggable jumper links are used in
most places.
Remove the base Start by removing the side
trims if fitted using a Pozi crosshead screwdriver.
Release the two M4 Pozi head pod securing screws
and rotate the connector pod to gain access to the
three M3 rear base fixing screws. Use a Torx
starhead screwdriver to remove these. Rotate the
pod again to remove the four M3 underside base
screws using the Torx driver. Carefully lift off the
base.
Configure the internal options Fit the
options required. Set the option jumpers to the
required positions. Make sure they are pressed fully
home. Check that all channels are correctly set and
all options fitted according to their instructions. Make
sure that no debris or parts are left loose inside the
console.
LIFT OFF BASE
AUX PRE/POST FADER
DIRECT OUT PRE/POST FADER
AUX PRE/POST INSERT/EQ
Refit the base Carefully reposition the base.
Refit the fixing screws. Lock the connector pod in
the required position using the securing screws.
Refit the side trims if required.
IMPORTANT: Check carefully that all channel
jumpers are correctly set as required. Errors on one
or more channels now may cause user problems
later. We recommend that you write the repositioned
jumper settings on a label and adhere this to the rear
panel. This would provide a helpful reference to
other users of the console.
MONO INPUTSTEREO INPUT (12:2)
AUX STEREO/MONO
AUX MASTERMASTER LR
AUX BALANCE OPTION
AB PRE/POST LR FADER
AUX PRE/POST FADER
ST AUX STEREO/MONO
26WZ316:2 and 12:2 User Guide
MONO CH - AUX PRE/POST EQ
L
AUXAUXDIR1-23-456
PRE-INSERT/POST-EQ
MONO CH - DIRECT OUT
L
AUXAUXDIR1-23-456
MONO CH - AUX PRE/POST FADER
PR=PRE
PO=POST
SW=SWITCH
L
AUXAUXDIR1-23-456
STEREO CH - AUX PRE/POST FADER
PR=PRE
PO=POST
SW=SWITCH
L
Aux pre/post insert/EQ
Factory default for
the mono channel pre-fade auxes is pre-insert, preEQ. This is popular with many users mixing monitors
from FOH. It prevents the channel EQ and inserted
ABCDEFGHIJK
PRPOPRPOSWPRSWPRSWPOSWPO
compressors affecting the monitor mix. Move the
jumper from A to B to change this to post-insert,
post-EQ if preferred. Note that auxes are always
post-mute.
Direct output source Factory default is pre-
fader. This is common for live recording to
ABCDEFGHIJK
PRPOPRPOSWPRSWPRSWPOSWPO
multitrack. The live mix fader movements do not
affect the recording. Move the jumper from C to D to
change to post-fade. Post-fade is appropriate when
using the output as a direct channel effects send.
Channel Aux pre/post settings Factory
default is Aux 1-2 = pre-fade, Aux 3-4 = switched,
Aux 5-6 = post-fade. You can change these settings
ABCDEFGHIJK
PRPOPRPOSWPRSWPRSWPOSWPO
ABCDEFGHIJK
SWPRSWPRSWPRSWPRSWPOSWPO
1
AUX23456
for different combinations of pre/post or switched
auxes by repositioning the links. Refer to the system
block diagram to explore the possibilities. Make sure
you set all mono and stereo channels the same.
Before you make your choice, consider whether you
want to use AUX5 or 5/6 for the internal effects
(should be post) and/or AUX6 to feed aux fed subs
(also post). We recommend you only change these
settings if absolutely necessary.
STEREO CH - MONO/STEREO AUXES
CN5
CN4
POST-FADE AUXES
STEREOMONO
PRE-FADE AUXES
STEREOMONO
AUX MASTER - ST1(5) MONO/STEREO
JP1
ST1(5) AUX SOURCE
STEREOMONO
LR MASTER - AB SOURCE
JP2
JP4
JP1
JP3
AB PRE/POST LR FADER
LRLR
PRE
POST
Stereo/Mono aux source The stereo
channels can feed the auxes with a mono sum of
L+R, or be configured so that L feeds the odd
numbered auxes, and R the even. This is preferred
when using odd/even auxes as stereo pairs. Factory
default is the mono setting. Note that you should
also set the ST1 (ST5) stereo/mono jumper to the
same position.
Effects return stereo/mono aux source
The return channel ST1 (5) feeds Auxes 1-4 with a
mono sum of the stereo signal. If you are working
with stereo auxes you can reconfigure this for stereo
with L feeding Auxes 1, 3 and R feeding Auxes 2, 4.
The jumper is found behind the AUX2 send control.
AB source pre or post LR faders The
factory default is that the post-fade LR mix feeds the
AB output. If you prefer the master LR faders not to
affect the AB output then reposition the two option
jumpers in the PRE position. This may be desired if
you are using the AB output to feed a 2-track
recording independent of the house level.
WZ316:2 and 12:2 User Guide 27
AUX MASTER - BALANCED OUTPUT OPTION
U12U11U10U9U8U7
1
AUX6AUX5AUX4AUX3AUX2AUX1
CUT OUT 2x 0 OHM RESISTOR LINKS
PLUG IN SSM2142 or DRV134 IC
AUX master balance option The 6 aux
outputs are impedance balanced as standard
operating at nominal -2dBu and with +21dBu
maximum drive. They provide similar interference
rejection to electronically balanced outputs when
connected to balanced equipment inputs. An
electronically balanced option is available if you
require nominal +4dBu and higher output drive up to
+26dBu over very long cable runs. However, it is not
usually necessary to fit this option as the impedance
balanced drive satisfies most applications. Check
that you really need the option before fitting it.
There are two balanced driver ICs which may be
used. Either is suitable. These are available from
Allen & Heath or most electronic component
suppliers. The Allen & Heath part number is shown
below:
SSM2142P A&H Part AE0302
DRV134 A&H Part AE5725
WZ312:2 OR WZ316:2
SYS-LINK II OUTPUT
SLAVE CONSOLE
37WAY CABLE
For each aux master, snip the legs of the two zero
ohm resistor links as shown. This removes them
from the circuit. Now simply plug the option IC into
the socket. Observe the correct IC pin1 orientation
and make sure its legs are correctly aligned with the
socket. Test the output once the work is complete.
You should measure the same level but opposite
polarity signal between + (hot) and ground, and –
(cold) and ground.
Sys-Link II output option A blank plate is
fitted here as standard. This may be replaced with
an optional card which provides a 37way D
connector for linking the outputs to other Allen &
Heath consoles already fitted with Sys-Link II. The
3
WZ
12:2 or WZ316:2 can become input channel
expanders for other consoles.
IMPORTANT: The option does not include the SysLink II input. Therefore the WZ
cannot be used as the master in a linked system, nor
can two of these models be linked together. You
need to connect these to a console that does include
the Sys-Link II input connection, for example the
3
WZ
14:4:2 or ML3000 with the option already fitted.
Also note that you need an adapter cable if you are
connecting Sys-Link II (Version 2) to the older SysLink I (Version 1) standard.
3
12:2 or WZ316:2
MASTER CONSOLE
SYS-LINK II INPUT
WZ314:4:2 OR OTHER A&H CONSOLE
SYS-LINK II OUTPUT
MixWizard balanced mix signals and PFL system to
the master console.
For full details please refer to the Sys-Link option
Applications Note AP5736 and Fitting Instructions
AP5735.
28WZ316:2 and 12:2 User Guide
A 37way shielded multi-core cable carries the
Cue Sheet WZ
Copy and use this page to record your console settings.
ALLEN&HEATH MixWizard WZ
+48V
PAD
(LINE)
0
30
40
20
GAIN
50
10- 10
4060
HPF
HF
-15
+15
3k
1k
4k
700
6k
500Hz
15k
HM
+15
-15
180
70
250
400
45
35Hz
1k
LM
-15
+15
LF
-15
+15
PRE
AUX
1
+6OO
AUX
2
+6OO
AUX
3
+6OO
AUX
4
+6OO
POST
PRE
AUX
5
+6OO
AUX
6
+6
OO
POST
=
PAN
RL
MUTE
PK!
PFL
SIG
10
5
0
5
10
+48V
PAD
(LINE)
0
30
40
20
GAIN
50
60 40
- 10 10
HPF
HF
+15
-15
3k
4k
1k
6k
700
15k
500Hz
HM
+15
-15
180
70
250
400
45
1k
35Hz
LM
+15
-15
LF
+15
-15
PRE
AUX
1
OO+6
AUX
2
OO+6
AUX
3
OO+6
AUX
4
OO+6
POST
PRE
AUX
5
OO+6
AUX
6
+6
OO
POST
=
PAN
LR
MUTE
PK!
PFL
SIG
10
5
0
5
10
GAIN
HM
LM
LF
AUX
AUX
AUX
AUX
AUX
AUX
PAN
- 10 10
HF
1
2
3
4
5
6
PK!
SIG
700
500Hz
45
35Hz
10
10
0
20
-15
1k
-15
70
-15
-15
PRE
OO+6
OO+6
OO+6
OO+6
OO+6
OO
POST
LR
5
0
5
+48V
PAD
(LINE)
30
0
40
20
GAIN
50
- 10 10
60 40
HPF
HF
+15
+15
+15
+15
MUTE
-15
1k
4k
700
6k
15k
500Hz
HM
-15
70
250
45
400
35Hz
1k
LM
-15
LF
-15
PRE
AUX
1
AUX
2
AUX
3
AUX
4
POST
PRE
AUX
5
AUX
6
+6
POST
PAN
PK!
SIG
10
3k
180
=
PFL
5
0
5
10
3
30
3k
180
OO+6
OO+6
OO+6
OO+6
OO+6
OO
=
LR
PFL
12:2
+48V
PAD
(LINE)
40
50
60 40
HPF
+15
4k
6k
15k
+15
250
400
1k
+15
+15
POST
PRE
+6
MUTE
3
12:2
LAMP
0
-5
5
+48V
PAD
(LINE)
0
30
40
20
GAIN
50
60 40
- 10 10
HPF
HF
+15
-15
3k
4k
1k
6k
700
15k
500Hz
HM
+15
-15
180
70
250
400
45
1k
35Hz
LM
+15
-15
LF
+15
-15
PRE
AUX
1
OO+6
AUX
2
OO+6
AUX
3
OO+6
AUX
4
OO+6
POST
PRE
AUX
5
OO+6
AUX
6
+6
OO
POST
=
PAN
LR
MUTE
PK!
PFL
SIG
10
5
0
5
10
+48V
PAD
(LINE)
0
30
40
20
GAIN
50
60 40
- 10 10
HPF
HF
+15
-15
3k
4k
1k
6k
700
15k
500Hz
HM
+15
-15
180
70
250
400
45
1k
35Hz
LM
+15
-15
LF
+15
-15
PRE
AUX
1
OO+6
AUX
2
OO+6
AUX
3
OO+6
AUX
4
OO+6
POST
PRE
AUX
5
OO+6
AUX
6
+6
OO
POST
=
PAN
LR
MUTE
PK!
PFL
SIG
10
5
0
5
10
+48V
PAD
(LINE)
0
30
40
20
GAIN
50
60 40
- 10 10
HPF
HF
+15
-15
3k
4k
1k
6k
700
15k
500Hz
HM
+15
-15
180
70
250
45
400
1k
35Hz
LM
+15
-15
LF
+15
-15
PRE
AUX
1
OO+6
AUX
2
OO+6
AUX
3
OO+6
AUX
4
OO+6
POST
PRE
AUX
5
OO+6
AUX
6
+6
OO
POST
=
PAN
LR
MUTE
PK!
PFL
SIG
10
5
0
5
10
+48V
PAD
(LINE)
0
30
40
20
GAIN
50
60 40
- 10 10
HPF
HF
+15
-15
3k
1k
4k
700
6k
15k
500Hz
HM
+15
-15
180
70
250
400
45
1k
35Hz
LM
+15
-15
LF
+15
-15
PRE
AUX
1
OO+6
AUX
2
OO+6
AUX
3
OO+6
AUX
4
OO+6
POST
PRE
AUX
5
OO+6
AUX
6
+6
OO
POST
=
PAN
LR
MUTE
PK!
PFL
SIG
10
5
0
5
10
GAIN
-10
10
-20
16
O
O
ON
LRTO
(ST1+ST2)TO
9-10
0
-5
GAIN
5
-10
10
-20
16
O
O
ON
HF
-15
+15
HM
-15
+15
LM
-15
+15
LF
-15
+15
PRE
AUX
1
OO+6
AUX
2
OO+6
AUX
3
OO+6
AUX
4
OO+6
POST
PRE
AUX
5
OO+6
AUX
6
+6
OO
POST
=
BAL
LR
MUTE
PK!
PFL
SIG
10
5
0
5
10
0
-5
5
GAIN
-10
10
-20
16
O
O
ON
TO LR
TO
(ST3+ST4)
11-12
0
-5
GAIN
5
-10
10
-20
16
O
O
ON
HF
+15
-15
HM
+15
-15
LM
+15
-15
LF
+15
-15
PRE
AUX
1
+6OO
AUX
2
+6OO
AUX
3
+6OO
AUX
4
+6OO
POST
PRE
AUX
5
+6OO
AUX
6
+6
OO
POST
=
BAL
RL
MUTE
PK!
PFL
SIG
10
5
0
5
10
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
FX
SINGLE
Vocal Plate
Slap Reverb
Classic Plate
Bright Plate
Perc Plate
Large Room
Hall+Stage
Concert Hall
St Chorus
Amb Flanger
St Doubler
2 Tap Delay
Slap Delay
Vocal Delay
St Delay
Karaoke
DUAL
Vocal Plate
Slap Reverb
Classic Plate
Bright Plate
Perc Plate
Large Room
Hall+Stage
Concert Hall
St Chorus
Amb Flanger
St Doubler
2 Tap Delay
Slap Delay
Vocal Plate
Classic Plate
Concert Hall
ST5 / FX
AUX
1
AUX
2
AUX
3
AUX
4
OO
2
3
5
6
816
/ FX
ST5
LEV
PRE
AUX
1
AUX
2
AUX
3
AUX
4
AUX
5
AUX
6
10
5
0
5
10
BANK
SINGLE FX
DUAL FX
AUX5 = 1-8
AUX6 = 9-16
AUX5 = 1-16
SEL
MUTE
+6OO
+6OO
+6OO
9+61
10
11
124
13
14
157
+6OO
+4OO
+4OO
+4OO
+4OO
+4OO
+4OO
PHONES
ST6
LEV
OO
0
TO LR
+16
+9
+6
+3
0
-3
-6
-9
-12
-16
-20
-30
R
L
PFL
PHONES
10
0
AUX 1
1-2
AUX 2
AUX 3
3-4
AUX
4
AUX 5
5-6
AUX 6
/ FX
ST5
ST6
M
ALL UP = LR
ALT LR OUT
MONITOR
AB
0
+10
OO
L+R
AUX 6
M
RL
10
5
0
5
10
20
30
OO
20
30
OO
20
30
OO
20
30
OO
20
30
OO
20
30
OO
20
30
OO
20
30
OO
20
30
OO
20
30
OO
20
30
20
30
OOOO
AUX6
WZ316:2 and 12:2 User Guide 29
+48V
PAD
(LINE)
0
GAIN
- 10 10
HF
700
500Hz
HM
45
35Hz
LM
LF
AUX
1
AUX
2
AUX
3
AUX
4
AUX
5
AUX
6
PAN
PK!
SIG
0
30
40
20
GAIN
50
- 10 10
60 40
HPF
HF
-15
+15
3k
1k
4k
1k
700
6k
15k
500Hz
HM
-15
+15
-15
180
250
70
70
45
400
35Hz
1k
LM
-15
+15
-15
LF
-15
+15
-15
PRE
AUX
1
OO+6
AUX
2
OO+6
AUX
3
OO+6
AUX
4
OO+6
POSTPOSTPOST
PRE
AUX
5
OO+6
AUX
6
+6
OO
POST
=
PAN
PK!
PFL
SIG
10
5
0
5
10
20
30
OO
Cue Sheet WZ
Copy and use this page to record your console settings.
16:2
PAD
0
40
20
GAIN
50
- 10 10
60 40
HPF
HF
-15
+15
1k
4k
700
6k
15k
500Hz
HM
-15
+15
250
70
45
400
35Hz
1k
LM
-15
+15
LF
-15
+15
AUX
1
O
+6
O
AUX
2
O+6
O
AUX
3
O
+6
O
AUX
4
+6
O
O
PRE
AUX
5
O+6O
AUX
6
O
+6OR+6
POST
PAN
R
L
SIG
10
5
0
5
10
20
30
OO
+48V
(LINE)
30
3k
180
=
PFL
+48V
+48V
PAD
(LINE)
(LINE)
0
30
40
20
GAIN
50
- 10
10
60 40
HPF
HF
-15
+15
3k
3k
1k
4k
700
6k
15k
500Hz
HM
-15
+15
180
250
70
45
400
35Hz
1k
LM
-15
+15
LF
-15
+15
AUX
1
OO
AUX
2
OO
AUX
3
OO
AUX
4
OO
POSTPOSTPO STPOSTPOSTPOST
PRE
AUX
5
OO
AUX
6
+6
OO
POST
=
PAN
L
PK!PK!
PFLPFL
SIG
10
5
0
5
10
20
30
OO
PAD
40
60 40
HPF
+15
4k
15k
+15
250
400
1k
+15
+15
+6
+6
+6
+6
PRE
+6
MUTEMUTEMUTE
0
20
GAIN
50
- 10 10
HF
-15
1k
700
6k
500Hz
HM
-15
70
45
35Hz
LM
-15
LF
-15
PREPRE
AUX
1
OO
AUX
2
AUX
3
OO
AUX
4
OO
AUX
5
AUX
6
OO
POST
PAN
LR
PK!
SIG
10
OO
5
0
5
10
20
30
+48V
PAD
(LINE)
30
HPF
+15
3k
15k
+15
180
+15
+15
=
PFL
40
GAIN
50
60 40
- 10 10
HF
4k
6k
700
HM
250
400
1k
LM
LF
AUX
1
+6
AUX
2
+6OO
AUX
3
+6
AUX
4
+6
PRE
AUX
5
+6OO
AUX
6
+6
PAN
PK!PK!
SIG
0
20
-15
1k
500Hz
-15
70
45
35Hz
-15
-15
OO
OO
OO
OO
OO
OO
POST
L
10
5
0
5
10
20
30
OO
+48V
PAD
(LINE)
30
40
50
60 40
HPF
+15
3k
4k
6k
15k
+15
180
250
400
1k
+15
+15
+6
+6
+6
+6
PRE
+6
=
R+6LR
PFL
+48V
PAD
(LINE)
30
40
20
GAIN
50
60 40
- 10 10
HPF
HF
-15
+15
3k
4k
6k
700
15k
HM
+15
180
250
400
1k
LM
+15
LF
+15
PREPRE
AUX
1
+6
OO
AUX
2
OO
+6
AUX
3
OO
+6
AUX
4
OO
+6
PRE
AUX
5
+6
OO
AUX
6
OO
+6
POST
=
PAN
RLR
L
MUTEMUTEMUTE
PK!
PFL
SIG
10
5
0
5
10
20
30
OO
MixWizard WZALLEN&HEATH
+48V
PAD
(LINE)
0
500Hz
45
35Hz
0
30
20
30
40
20
GAIN
50
- 10 10
60 40
HPF
HF
-15
-15
+15
3k
1k
4k
1k
700
6k
15k
500Hz
HM
-15
+15
-15
180
70
-15
-15
OO
OO
OO
OO
OO
OO
POST
L
PFL
10
5
0
5
10
20
30
OO
180
250
70
45
400
35Hz
1k
LM
+15
-15
LF
+15
-15
PREPREPRE
AUX
1
+6
OO+6
AUX
2
OO+6
+6
AUX
3
OO+6
+6
AUX
4
OO+6
+6
PRE
AUX
5
OO+6
+6
AUX
6
OO
+6
POST
=
=
PAN
LR
R
PK!
SIG
10
5
0
5
10
20
30
OO
3
16:2
+48V
PAD
40
GAIN
50
60 40
HPF
HF
+15
4k
6k
15k
HM
+15
250
400
1k
LM
+15
LF
+15
AUX
AUX
AUXAUX
AUX
PRE
AUX
AUX
+6
PAN
MUTEMUTEMUTE
+48V
PAD
(LINE)
0
30
40
20
50
60 40
- 10 10
HPF
-15
+15
3k
4k
1k
6k
700
15k
500Hz
+15
-15
180
250
70
400
45
1k
35Hz
+15
-15
+15
-15
1
OO
+6
2
OO
+6
3
OO
+6
4
OO
+6
PRE
5
OO
+6
6
OO
+6
POST
=
L
R
PK!PK!
PFL
SIG
10
5
0
5
10
20
30
OO
0
30
20
GAIN
- 10 10
HF
-15
3k
1k
700
500Hz
HM
-15
180
70
45
35Hz
LM
-15
LF
-15
PREPREPRE
AUX
1
O+6
O
AUX
2
O+6
O
3
O
O+6
AUX
4
O+6
O
AUX
5
O
O+6
AUX
6
O
O
POST
=
PAN
L
PFL
SIG
10
5
0
5
10
20
30
OO
+48V
(LINE)
0
30
20
GAIN
- 10 10
HF
-15
3k
1k
700
500Hz
HM
-15
180
70
45
35Hz
LM
-15
LF
-15
PRE
AUX
1
OO+6
AUX
2
OO+6
AUX
3
OO+6
AUX
4
OO+6
AUX
5
OO+6
AUX
6
OO
POST
=
PAN
PFL
SIG
10
5
0
5
10
20
30
OO
+48V
PAD
(LINE)
0
30
40
20
GAIN
50
- 10 10
60 40
HPF
HF
-15
+15
3k
1k
4k
700
6k
15k
500Hz
HM
-15
+15
180
250
70
45
400
35Hz
1k
LM
-15
+15
LF
-15
+15
PREPREPRE
AUX
1
O
O
AUX
2
O
O
AUXAUX
O3O
AUX
O4O
PRE
AUX
5
OO
AUX
6
O
O
+6
POST
=
PAN
L
MUTEMUTEMUTE
PK!
PFL
SIG
10
5
0
5
10
20
30
OO
+48V
PAD
(LINE)
0
30
40
20
GAIN
50
60 40
- 10 10
HPF
HF
-15
+15
3k
4k
1k
6k
700
15k
500Hz
HM
+15
-15
180
250
70
400
45
1k
35Hz
LM
+15
-15
LF
+15
-15
AUX
1
+6
OO
AUX
2
+6
OO
3
+6
OO
AUX
4
+6
OO
POSTPOSTPOSTPOSTPOST
PRE
AUX
5
+6OO
AUX
6
+6OO
POST
=
PAN
RL
PK!PK!
PFLPFL
SIG
10
5
0
5
10
20
30
OO
+48V
PAD
(LINE)
0
30
40
20
GAIN
50
- 10 10
60 40
HPF
HF
-15
+15
3k
1k
4k
700
6k
15k
500Hz
HM
-15
+15
180
250
70
45
400
35Hz
1k
LM
-15
+15
LF
-15
+15
AUX
1
+6
OO+6
AUX
2
+6
OO+6
AUX
3
+6
OO+6
AUX
4
+6
OO+6
PRE
AUX
5
+6
OO+6
AUX
6
+6
OO
POST
=
PAN
R
LR
SIG
10
5
0
5
10
20
30
+48V
PAD
(LINE)
HPF
PAD
(LINE)
0
40
60 40
+15
15k
+15
1k
+15
+15
+6
MUTEMUTE
40
20
GAIN
50
4k
6k
HM
250
400
LM
PRE
PAN
R
GAIN
50
60 40
- 10 10
HPF
HF
HF
-15
+15
3k
4k
1k
6k
700
15k
500Hz
HM
+15
-15
180
250
70
400
45
1k
35Hz
LM
+15
-15
LF
LF
+15
-15
AUX
AUX
1
1
OO
+6
AUX
AUX
2
2
OO
+6
AUX
AUX
3
3
OO
+6
AUX
AUX
4
4
+6
OO
POST
PRE
AUX
AUX
5
5
+6
OO
AUX
AUX
6
6
+6
OO
POST
=
PAN
R
L
MUTE
PK!
PK!
PFL
SIG
SIG
10
5
0
5
10
20
30
OO
AUX
+48V
1
PAD
OO+6
(LINE)
AUX
0
3030
2
40
20
50
OO+6
AUX
10- 10
4060
3
HPF
OO+6
AUX
4
-15
1k
700
500Hz
-15
70
45
35Hz
-15
-15
PRE
OO
OO
OO
OO
OO
OO
POST
L
10
10
20
30
OO
+15
3k
1+69
4k
6k
10
2
11
3
15k
+15
180
250
400
1k
+15
+15
+6
+6
+6
+6
POST
PRE
+6
+6
=
R
MUTE
PFL
5
0
5
OOOO
2
3
4
5
6
7
8
9
10
12
13
14
15
16
2
3
4
5
6
7
8
9
10
12
13
14
15
16
ST1
LEV
AUX
1
AUX
2
AUX
3
AUX
4
AUX
5
AUX
6
Vocal Plate
Slap Reverb
Classic Plate
Bright Plate
Perc Plate
Large Room
Hall+Stage
Concert Hall
St Chorus
Amb Flanger
St Doubler
2 Tap Delay
Slap Delay
Vocal Delay
St Delay
Karaoke
Vocal Plate
Slap Reverb
Classic Plate
Bright Plate
Perc Plate
Large Room
Hall+Stage
Concert Hall
St Chorus
Amb Flanger
St Doubler
2 Tap Delay
Slap Delay
Vocal Plate
Classic Plate
Concert Hall
FX
SINGLE
DUAL
4
5
6
7
/ FX
OO+6
PRE
OO+4
OO+4
OO+4
OO+4
OO+4
OO+4
AUX5 = 1-8
AUX6 = 9-16
AUX5 = 1-16
12
13
14
15
168
BANK
SEL
MUTE
SINGLE FX
DUAL FX
L10R
ST2
LEV
L
1-2
3-4
5-6
OO
5
0
5
10
20
30
OOO
PHONES
OO
0
TO LR
+16
+9
+6
+3
0
-3
-6
-9
-12
-16
-20
-30
R
PFL
PHONES
0
10
1AUX
2AUX
3AUX
4AUX
5AUX
6AUX
/ FX
ST1
ST2
M
ALL UP = LR
ALT LR OUT
MONITOR
AB
0
+10
L+R
AUX 6
M
10
5
0
5
10
20
30
O
AUX6
30WZ316:2 and 12:2 User Guide
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.