M-MMO Card Option AP7654
Instructions
Part number M-MMO-A
The
Mini Multi Out (MMO) module is one of several plug-
in card options that may be fitted to iLive Port B or the GLD I/O port.
It provides three formats of multi-channel digital output
simultaneously available for recording, personal monitoring and
signal distribution.
ADAT 3x 8-channel optical ADAT output ports for up to 24 track
recording or signal interfacing using the popular ADAT standard.
iDR / Hearbus 2x 8-channel RJ45 ports suitable for connection
to the Allen & Heath iDR Series digital mix processors and output
expanders. Up to two expanders or iDR units may be connected to
transport up to 16 signals. These connections are also compatible
with the Hearbus personal monitoring distribution hub.
Note Connect to the Hearbus distribution hub. Do not connect
directly to a Hearbus mixer or ‘Extreme Expander’.
iDR Output A and Output B each have two connections, AUDIO and
DR-LINK. DR-LINK provides meter and status data and is only
needed when connecting to the iDR-out (analogue) or iDR-Dout
(AES, Spdif, Toslink) expanders. To connect to an iDR-8 or iDR-4
mix processor or to a Hearbus hub use the AUDIO port only.
Use CAT5 cables up to 250m (825’) long.
iDR-out
REMOTE AUDIO 2
ON
0
SYSTEM LOCK
iDR10
RAB2 module
10
PAFL
(CHK)
Port A
Port B
SYNC
IN
AUDIO
CLOCK
SYNC
OUT
MINI
MULTI-OUT
1-8
ADAT OUT
9-16 17-24
AB
iDR
/HearBus
(HUB)
iDR Expander
AVIOM
DR-LINK
AUDIO
TM
AVIOM 16 channel
Compatible
Surface
RAB2 module
100
ON
REMOTE AUDIO 2
I/O Port
iDR Expander
ADAT OUT
DR-LINK
9-16 17-24
iDR
/HearBus
AB
(HUB)
AUDIO
TM
AVIOM
AVIOM 16 channel
MINI
1-8
MULTI-OUT
Port B
Usually fitted to Port B
Port A = Surface to MixRack audio link
ADAT OUT
MINI
1-8
9-16 17-24
MULTI-OUT
Port A
PAFL
(CHK)
SYSTEM LOCK
A&H
Compatible
MINI
MULTI-OUT
ADAT OUT
1-8
9-16 17-24
iDR
/HearBus
AB
Port B
iDR AVIOM
/HearBus
AB
(HUB)
iDR Expander
DR-LINK
AUDIO
TM
(HUB)
AVIOM
AVIOM 16 channel
DR-LINK (control) AUDIO (8 channels)
iDR-Dout
Aviom® Plug a CAT5 cable into this port to transport 16 signals to
the Aviom personal monitoring system.
Fitting to the iDR-64, 48, 32, 16 and GLD
The M-MMO card option may be fitted to the Port B slot in the iLive
fixed format MixRacks, and the I/O port in the GLD mixer. Make sure
the equipment is switched off. Remove the 2 screws securing the
blank panel over Port B. Slide the M-MMO card into the slot and
press it firmly into the mating connector. Secure the card in place
using the 2 screws.
iDR Expander
DR-LINK
AUDIO
TM
Compatible
AVIOM 16 channel
Compatible
SYNCINSYNC
AUDIO
CLOCK
Fitting to iDR10 and iLive Surfaces
The option card can be fitted into the Port A or Port B slot in the
Remote Audio 2 (RAB2) module. It is usual to fit the option to Port B
as Port A is typically used for the Surface to MixRack audio link.
Systems fitted with the older Remote Audio module can be
upgraded with the new RAB2 module. The option port is not
available on the T or R Series Surfaces.
Make sure the System is switched off. Remove the 2 screws
securing the blank panel over the port slot . Slide the M-ACE card
OUT
into the slot and press it firmly into the mating connector. Secure
the card in place using the 2 screws.
iLive M- MMO Option Instructions AP7654 issue 5
Port B fitted with MMO card option
Patching signals to MixRack Port B
iLive recognises the type of option card fitted to Port B of the
MixRack. Use the TouchScreen or Editor OUTPUTS screen Port B
tab. You can assign one or a range of signals to the different
outputs by touching the output you want to assign and choosing
selections from the drop down menu. Touch Apply to confirm the
selection.
The input and output patching including Port B is archived within the
Show memories and can be stored in the Scenes ‘Patchbay’ item.
Patching signals to Surface Port B
Note The M-MMO card is the only option supported in the iLive
Surface RAB2 module Port B.
Note If you intend to use the Aviom
iLive system is running firmware version
Port B at the modular iLive Surface can be used to provide outputs
for recording, personal monitoring and further signal distribution.
This applies only to modular iLive Surfaces with the RAB2 module
fitted. The T and R Series Surfaces do not include Port B.
®
port then make sure your
V1.91 or higher.
M-MMO in Surface Port B
Assignment map:
Port A is used to link local audio at the Surface to and from the
MixRack. It carries 64 signals in both directions. Link channels 1-32
and 63/64 are reserved for the local audio card slots and PAFL
monitor, while link channels 33-62 are available for further signal
distribution from Port B at the Surface, for example recording.
The Status screen does not recognise the Port B option even if one
is fitted. The card can be used but no information is displayed here.
Make sure the Surface Redundant Link setting in the MIXRACK
SETUP / Preferences / Port A/B screen is turned On.
Use the TouchScreen or Editor OUTPUTS screen ACE Link or ESA
tab to assign signals to the M-MMO option fitted in Port B. Use
CH33 and higher. These are permanently mapped to the M-MMO
output sockets according to the table below.
You can assign one or a range of signals to the different outputs by
touching the output you want to assign and choosing selections
from the drop down menu. Touch Apply to confirm the selection.
iDR B
Not used
ADAT
9 = 41
1 = 33
2 = 34
3 = 35
4 = 36
5 = 37
6 = 38
7 = 39
8 = 40
2 iLive MMO Option Instructions AP7654 issue 5
10 = 42
11 = 43
12 = 44
13 = 45
14 = 46
15 = 47
16 = 48
17 = 49
18 = 50
19 = 51
20 = 52
21 = 53
22 = 54
23 = 55
24 = 56
iDR A
1 = 57
2 = 58
3 = 59
4 = 60
5 = 61
6 = 62
7 = PAFL L
8 = PAFL R
1 = 41
2 = 42
3 = 43
4 = 44
5 = 45
6 = 46
7 = 47
8 = 48
AviomTM
9 = 49
10 = 50
11 = 51
12 = 52
13 = 53
14 = 54
15 = 55
16 = 56
I/O Port fitted with MMO card option
Up to 64 GLD inputs and 64 outputs can be assigned to an audio option card fitted to the GLD-80 rear panel I/O Port.
The MMO (Mini Multi Out) card uses 56 channels from the port.
Use the I/O screen I/O Port Out tab to patch signals to the MMO
card outputs. The port channels map to the MMO sockets as below.
Touch to highlight a channel, use the drop-down menu to select a
signal type and then Start and End boxes to select the number and
range. Press Apply to confirm.
GLD Port Map
Port Out: MMO:
ADAT
1 ADAT 1
2 ADAT 2
3 ADAT 3
4 ADAT 4
5 ADAT 5
6 ADAT 6
7 ADAT 7
8 ADAT 8
9 ADAT 9
10 ADAT 10
11 ADAT 11
12 ADAT 12
13 ADAT 13
14 ADAT 14
15 ADAT 15
16 ADAT 16
17 ADAT 17
18 ADAT 18
19 ADAT 19
20 ADAT 20
21 ADAT 21
22 ADAT 22
23 ADAT 23
24 ADAT 24
This product complies with the European
Electromagnetic Compatibility directive 2004/108/EC.
Copyright© 2013 Allen & Heath Ltd. All rights reserved.
For further information refer to www.allen-heath.com
GLD Port Map
Port Out: MMO:
iDR A
25 iDR-A 1
26 iDR-A 2
27 iDR-A 3
28 iDR-A 4
29 iDR-A 5
30 iDR-A 6
31 iDR-A 7
32 iDR-A 8
iDR B
33 iDR-B 1
34 iDR-B 2
35 iDR-B 3
36 iDR-B 4
37 iDR-B 5
38 iDR-B 6
39 iDR-B 7
40 iDR-B 8
GLD Port Map
Port Out: MMO:
41 Aviom 1
42 Aviom 2
43 Aviom 3
44 Aviom 4
45 Aviom 5
46 Aviom 6
47 Aviom 7
48 Aviom 8
49 Aviom 9
50 Aviom 10
51 Aviom 11
52 Aviom 12
53 Aviom 13
54 Aviom 14
55 Aviom 15
56 Aviom 16
NOTE: Any changes or modifications to the
equipment not approved by Allen & Heath could void
the compliance of the equipment. Whilst we believe
the information in these instructions to be reliable we
do not assume responsibility for inaccuracies. We also
reserve the right to make changes in the interest of
further product development.
Aviom
®
Assign each output:
• Unassigned
• Input Direct Out
• Group
• Aux
• Main Mix
• Matrix
• Rack FX
• USB playback
• Input socket
• I/O Port input
• PAFL monitor
• Wedge/IEM monitor
iLive M- MMO Option Instructions AP7654 issue 5
Loading...