Alinco DJ-S17 E, DJ-S17, DJ-S17 TFH, DJ-S 47 E, DJ-S 47 User Manual
ALINCO, INC.
VHF/UHF FM TRANSCEIVER
DJ-S17 E/TFH
DJ-S47 E
Instruction Manual
Thank you for purchasing your new Alinco transceiver.
This instruction manual contains important safety and
operating instructions. Please read this manual
carefully before using the product and keep it for future
reference.
VOL
V/M/C
SQL
KL
N
A
M
E
M
W
R
P
T
P
O
DJ-S17
UHF FM TRANSCEIVER
VOL
V/M/C
SQL
KL
N
A
M
E
M
W
R
P
T
P
O
DJ-S47
UHF FM TRANSCEIVER
2
NOTICE / Compliance Information Statement
3
NOTICE / Compliance Information Statement
Conformity Information
Alinco, Inc. Electronics Division hereby declare on our sole responsibility that the
product(s) listed below comply the essential requirements of the Directive 1999/5/EC,
The council of 3/9/99 on Radio Equipment and Telecommunication Terminal
Equipment and the mutual recognition of their conformity and with the provisions of
Annex, after having performed the required measurements at Notified Bodies per
Standards, and relative certificate(s) or document(s) can be reviewed at http://www.
alinco. com/Ce/
DJ-S17E: VHF FM Transceiver 144.000~145.995MHz
DJ-S47E: UHF FM Transceiver 430.000~439.995MHz
This device is authorized for use in all EU and EFTA member states. An operator's
license is required for this device.
Copyright © All rights reserved. No part of this document may be reproduced, copied,
translated or transcribed in any form or by any means without the prior written
permission of Alinco. Inc., Osaka, Japan, English Edition Printed in Japan.
Warning
4
Warning
To prevent any hazard during operation of Alinco's radio product, in this manual and
on the product you may find symbols shown below. Please read and understand the
meanings of these symbols before starting to use the product.
Alert
Environment and condition of use
The manufacturer declines any responsibilities against loss of life and/or
property due to a failure of this product when used to perform important tasks
like life-guarding, surveillance, and rescue.
a
Use of this product may be prohibited or illegal outside of your country. Be
informed in advance when you travel.
j
Never operate this product in facilities where radio products are prohibited for
use such as aboard aircraft, in airports, in ports, within or near the operating
area of business wireless stations or their relay stations.
j
In case a liquid leaks from the product, do not touch it. It may damage your
skin. Rinse with plenty of cold water if the liquid contacted your skin.
j
Keep the radio out of the reach of children.
a
Do not use this product in close proximity to other electronic devices,
especially medical ones. It may cause interference to those devices.
j
It is recommended that you check local traffic regulations regarding the use of
radio equipment while driving. Some countries prohibit or apply restrictions
for the operation of radios and mobile- phones while driving.
a
■
d
d
Danger
This symbol is intended to alert the user to an immediate danger that
may cause loss of life and property if the user disregards the warning.
d
Alert
This symbol is intended to alert the user to a possible hazard that
may cause loss of life and property if the user disregards the warning.
d
Caution
This symbol is intended to alert the user to a possible hazard that may
cause loss of property or injure the user if the warning is disregarded.
d
Alert symbol. An explanation is given.
a
Warning symbol. An explanation is given.
m
Instruction symbol. An explanation is given.
Warning
5
Handling this product
About chargers
About power supply
Do not plug multiple devices including the power supply into a single wall
outlet. It may result in overheating and/or fire.
j
Do not connect cables in reverse polarity. It may result in electric shock, fire
and/or malfunction.
j
Use only appropriate, reliable power supply of correct voltage and capacity.
j
■
Do not use the adapter if the plug or socket contacts are dirty. Overheating and/or
short-circuiting may result in fire, electric shock and/or damage to the product.
j
Securely plug the adapter into the wall outlet. Insecure installation may result
in short-circuit, electronic shock and/or fire.
a
Do not handle adapter with a wet hand. It may result in electric shock.
j
Do not plug multiple devices using an adapter into a single wall outlet. It may
result in overheating and/or fire.
j
Do not use adapters other than having the specified voltage. It may result in
electric shock, fire and/or malfunction.
j
■
Do not place the product in a container carrying conductive materials, such as
water or metal in close proximity to the product. A short-circuit to the product
may result in electric shock, fire and/or malfunction.
j
Do not operate this product in a wet place such as shower room. It may result
in electric shock, fire and/or malfunction.
l
Do not open the unit without permission or instruction from the manufacturer.
Unauthorized modification or repair may result in electric shock, fire and/or
malfunction.
m
Be sure to reduce the audio output level to minimum before using an earphone
or a headset. Excessive audio may damage hearing.
a
■
Use of third party accessory may result in damage to this product. It will void
our warranty for repair.
a
The manufacturer declines any responsibilities against loss of life and property due to
a failure of this product when used with or as a part of a device made by third parties.
a
Risk of explosion if battery is replaced with an incorrect type.
Dispose of, or recycle used batteries according to your local regulations.
a
Do not use multiple radios in very close proximity. It may cause interference
and/or damage to the product(s).
j
Warning
6
Cigar-lighter cable
In case of emergency
In case of the following situation(s), please turn off the product, switch off the source
of power, then remove or unplug the power-cord. Please contact your local dealer of
this product for service and assistance. Do not use the product until the trouble is
resolved. Do not try to troubleshoot the problem by yourself.
• When a strange sound, smoke and/or strange odor comes out of the product.
• When the product is dropped or the case is broken or cracked.
• When a liquid penetrated inside.
• When a power cord (including DC cables, AC cables and adapters) is damaged.
Maintenance
Do not open the unit and its accessories. Please consult with your local dealer
of this product for service and assistance.
m
■
For your safety, turn off then remove all related AC lines to the product and its
accessories from the wall outlet if a thunderstorm is likely.
a
■
Do not handle cigar cable with a wet hand. It may result in electric shock.
j
Do not use the cable at any other than the specified voltage. It may result in
electric shock, fire and/or malfunction.
j
■
Do not modify or remove fuse-assembly from the DC cable. It may result in
fire, electric shock and/or damage to the product.
j
Do not plug the power supply into the wall socket if the contacts are dirty.
Short-circuit and/or overheating may result in fire, electric shock and/or
damage to the product.
j
Securely plug the power supply to the wall outlet. Insecure installation may
result in short-circuiting, electronic shock and/or fire.
a
Do not handle a power supply with a wet hand. It may result in electric shock.
j
Warning
7
Caution
Environment and condition of use
About transceiver
About power supply
When a unit is powered from an external DC power source (adapter, power
supply, cigar-plug etc), please make sure that such external DC power source
shall be a limited power source per IEC/EN 60950-1.
a
When using an external antenna, make sure that the antenna ground is not
common with the ground of the power supply.
a
Always turn off the power supply when connecting or disconnecting the cables.
a
Use only reliable power supply of specific DC output range and be mindful of
the polarity of the cable and DC-jack.
a
■
Use a clean, dry cloth to wipe off dirt and condensation from the surface of the
product. Never use thinner or benzene for cleaning.
a
Never pull the cord alone when you unplug AC cable form the wall outlet.
j
Turn off and remove the power source (AC cable, DC cable, battery, cigar
cable, charger adapter etc.) from the product when the product is not in use for
extended period of time or in case of maintenance.
a
Do not connect devices other than specified ones to the jacks and ports on the
product. It may result in damage to the devices.
j
Be cautious of the whip antenna when carried in your shirt-pocket etc. It may
make contact with your eye and cause injury.
a
■
Be cautious of a dew formation. Please completely dry the product before use
when it happens.
j
Do not install the product in proximity to a source of heat and humidity such as
a heater or a stove. Avoid placing the unit in direct sunlight.
j
Do not install in an unstable or vibrating position. It may result in electric
shock, fire and/or malfunction when/if the product falls to the ground.
j
Do not install in a humid, dusty or insufficiently ventilated place. It may result
in electric shock, fire and/or malfunction.
j
Do not use the product in proximity to a TV or a radio. It may cause
interference or receive interference.
j
■
d
Warning
8
Lightning
Any person is not safe outdoor during thunderstorm and lightning. This condition is
getting worse if somebody keeps a hand-held radio; chances of being hit by lightning are
doubled since lightning may hit a radio antenna as well. At this time, there is no handheld radio having any kind of protection against lightning current (which is higher than
10 kA.). Note also that no car provides adequate protection of its passengers or drivers
against lightning as well. Therefore, Alinco will not take responsibility for any danger
associated with using its hand-held radios outdoor or inside the car during lightning.
Limited Power Source
Adhering to the requirement of the following warning ensures compliance of the
transceiver with the safety standard for information technology equipment, EN 60950-
1. Please note that the transceiver enclosure only provides mechanical protection of
its internal parts; it will not contain a fire within the device if the fire starts under
certain fault conditions. Alinco will not take responsibility for any fire hazard
associated with powering the transceiver or charging its batteries using a power source
which does not belong to the limited power sources in the meaning of EN 60950-1.
Excluded from possible use with the transceiver are most car cigarette lighters and
some DC (AC/DC) power supplies. Make sure that the power supply used with the
transceiver is a limited power source.
Water-proof
The IEC 60529/IPX7 is an European system of test specification standards for
classifying the degrees of protection provided by the enclosures of electrical
equipment. An IPX7 designation means that the unit withstands immersion in one
meter (approx 3ft) of still water for up to 30 minutes.
The factory guarantees this grade for 1 year provided all the jack covers are properly
and securely closed. However, please understand that this unit is NOT an IPX7
COMPLIANT, but compatible; we have tested and approved at our engineering stage
that this product meets the requirement of IPX7 but we do not test it unit-by-unit at the
factory before delivery. Please understand that water-pressure such as washing the
unit with running water may cause damage to the unit and voids warranty. Never
immerse the unit uselessly under the water (V/UHF signal does not propagate in water
at all). If the unit is dropped in water, please pick it up immediately and wipe with a
clean dry cloth. Use only specified water-proof accessories when the unit is intended
for use in rainy/wet conditions.
■
■
■
Introduction
9
Introduction
Thank you very much for purchasing this excellent Alinco transceiver. Our products
are ranked among the finest in the world. This radio has been manufactured with state
of the art technology and it has been tested carefully at our factory. It is designed to
operate to your satisfaction for many years under normal use.
PLEASE READ THIS MANUAL COMPLETELY TO LEARN ALL THE
FUNCTIONS THE PRODUCT OFFERS. WE MADE EVERY ATTEMPT TO
WRITE THIS MANUAL TO BE AS COMPREHENSIVE AND EASY TO
UNDERSTAND AS POSSIBLE. IT IS IMPORTANT TO NOTE THAT SOME OF
THE OPERATIONS MAY BE EXPLAINED IN RELATION TO INFORMATION
IN PREVIOUS CHAPTERS. BY READING JUST ONE PART OF THE MANUAL,
YOU RISK NOT UNDERSTANDING THE COMPLETE EXPLANATION OF THE
FUNCTION.
10
Contents
Contents
NOTICE / Compliance Information Statement................................................3
Warning...............................................................................................................4
Introduction ........................................................................................................9
Contents ...........................................................................................................10
1.Features .........................................................................................................13
1.1 Accessories .........................................................................................................13
2.Accessories ...................................................................................................14
2.1 Installations.........................................................................................................14
2.1.1 Antenna ......................................................................................................14
2.1.2 Hand Strap..................................................................................................14
2.1.3 Belt Clip .....................................................................................................14
2.1.4 Battery Pack ...............................................................................................15
2.1.5 Prevent Short Circuiting the Battery Pack .................................................17
2.1.6 Dry Cell Case (optional).............................................................................18
2.1.7 Battery-Level Icon......................................................................................19
3.Names and Operations of Parts ..................................................................20
3.1 Names and Operations of Keys and Ports...........................................................20
3.2 Keypad ................................................................................................................22
3.3 Display (LCD) ....................................................................................................23
4.Basic Operation ............................................................................................24
4.1 Turning On the Power.........................................................................................24
4.2 Adjusting the Audio Output (Volume) ...............................................................24
4.3 Adjusting the Squelch.........................................................................................25
4.4 Setting the Frequency in the VFO Mode ............................................................25
4.4.1 Setting the Frequency.................................................................................25
4.4.2 Setting the Tuning Step ..............................................................................25
4.4.3 Shift Direction and Offset Frequency Settings...........................................26
4.5 Memory Mode ....................................................................................................27
4.5.1 How to Program Memory Channel(s) ........................................................27
4.5.2 Recalling a Memory Channel.....................................................................28
4.5.3 Deleting a Memory Channel ......................................................................28
4.5.4 How to Program Call Channel ...................................................................28
4.5.5 Programming a Repeater-Access Function Setting....................................28
4.5.6 Programmable Parameters in Memory Channels.......................................29
4.6 Call-Channel Mode.............................................................................................30
11
Contents
4.7 Receiving ............................................................................................................30
4.7.1 Monitor Function........................................................................................30
4.8 Transmitting .......................................................................................................31
4.8.1 Selecting the Output Level .........................................................................31
5.Useful Functions ...........................................................................................32
5.1 Scan Modes.........................................................................................................32
5.1.1 VFO-Scan...................................................................................................32
5.1.2 Memory-Scan .............................................................................................32
5.1.3 Setting Skip Channels ................................................................................33
5.2 Keylock...............................................................................................................33
5.3 Tone-Burst ..........................................................................................................33
5.4 Naming Memory Channels.................................................................................34
5.4.1 Setting Name-Tag.......................................................................................34
5.4.2 Using the Channel Name Function ............................................................34
5.5 Auto-Power-Off (APO) ......................................................................................35
5.5.1 Setting APO................................................................................................35
5.5.2 APO Operation ...........................................................................................35
5.6 Time-Out-Timer (TOT) ......................................................................................35
5.6.1 Setting TOT................................................................................................35
5.6.2 TOT Operation ...........................................................................................35
5.7 Lamp ..................................................................................................................36
6.Selective Calling............................................................................................37
Selective Calling Operations ...................................................................................37
6.1 Tone Squelch (TSQ) ...........................................................................................37
6.1.1 Setting the Tone Squelch............................................................................37
6.1.2 Setting the Tone Frequency........................................................................37
6.1.3 Switching Off the Tone Squelch ................................................................38
6.1.4 To Differentiate the ENC/DEC Tones .......................................................38
6.1.5 Tone Squelch Operation.............................................................................38
6.2 DCS ....................................................................................................................38
6.2.1 Setting the DCS..........................................................................................38
6.2.2 Changing the DCS Code ............................................................................39
6.2.3 Switching Off DCS ....................................................................................39
6.2.4 DCS Operation ...........................................................................................39
7.Special Functions..........................................................................................40
7.1 ATT (Attenuator)................................................................................................40
7.2 Battery Refresh ...................................................................................................40
7.3 Repeater-Access..................................................................................................41
■
12
Contents
8.Set Mode........................................................................................................42
8.1 Set Mode Operation ............................................................................................42
8.2 Entering the Set Mode ........................................................................................43
8.3 Available Parameters ..........................................................................................43
8.3.1 Menu 1 Battery Save (BS) Function ..........................................................43
8.3.2 Menu 2 Timer/Busy Scan Setting ..............................................................43
8.3.3 Menu 3 Beep Function ...............................................................................44
8.3.4 Menu 4 Tone-Burst Frequency Setting ......................................................44
8.3.5 Menu 5 Clock Shift Setting........................................................................44
8.3.6 Menu 6 Busy Channel Lockout Setting .....................................................45
8.3.7 Menu 7 TOT (Time-Out-Timer) Setting ....................................................45
8.3.8 Menu 8 TOT Penalty Time ........................................................................45
8.3.9 Menu 9 Tuning Step Setting.......................................................................45
8.3.10 Menu 10 Shift Direction Setting ................................................................45
8.3.11 Menu 11 Offset Frequency Setting ............................................................45
8.3.12 Menu 12 Tone Squelch Setting ..................................................................46
8.3.13 Menu 13 Tone Frequency Setting ..............................................................46
8.3.14 Menu 14 DCS Setting.................................................................................46
8.3.15 Menu 15 APO (Auto-Power-Off) Setting ..................................................46
8.3.16 Menu 16 Skip Channel Setting...................................................................46
8.3.17 Menu 17 ATT (Attenuator) Setting............................................................46
8.3.18 Menu 18 Battery Charge Function .............................................................46
8.3.19 Menu 19 Battery Type Setting ...................................................................47
9.Cloning and Packet Operation ....................................................................48
9.1 Cloning................................................................................................................48
9.1.1 Cable Connection .......................................................................................48
9.1.2 Master/Slave Units .....................................................................................48
9.1.3 Master Unit Operation................................................................................49
9.1.4 Slave Unit Operation ..................................................................................49
9.2 Packet Operation.................................................................................................50
9.2.1 Packet Operation Connections ...................................................................50
10.Maintenance and Reference......................................................................51
10.1 Troubleshooting ..................................................................................................51
10.2 Resetting .............................................................................................................52
10.3 Options................................................................................................................53
10.3.1 Microphone/Speaker Cable (EDS-10)........................................................54
10.3.2 Battery Packs..............................................................................................54
10.3.3 Using the Chargers .....................................................................................55
11.Specifications .............................................................................................61
1.Features
1
13
1. Features
This transceiver has the following main features.
High-grade waterproof compatible to IPX7* (submersible 1m/3feet for
30min.) and rugged body
39 CTCSS tone squelch
104 DCS digital code squelch
Time-Out-Timer
Alphanumeric display
4 tone-burst tones (1750, 2100, 1000, 1450Hz)
A quick "Repeater-Access" function
Refresh function for rechargeable battery reconditioning
Cable Cloning
* Please read page 8 for more details.
• Ni-MH battery pack EBP-65 (7.2V 700mAh)
• EDC-147 (AC 230V) wall charger (E/TFH version)/EDC-148 (U.K. models)
• Flexible whip antenna EA0141 (DJ-S17E version)
• Flexible whip antenna EA0142 (DJ-S17TFH version)
• Flexible whip antenna EA0143 (DJ-S47E version)
• Belt clip
• Hand strap
• Instruction manual
* Accessories may differ depending on the version you have purchased.
Please contact your local dealer for details of standard accessories and the warrantypolicy before purchase.
Accessories
1.1
■
■
■
■
■
■
■
■
■
2.Accessories
2
14
2. Accessories
2.1.1 Antenna
Attaching the Antenna
1. Hold the antenna by its base.
2. Align the grooves at the base of the antenna with
the protrusions on the antenna connector.
3. Slide the antenna down and turn it clockwise until
it stops.
4. Confirm that the antenna is securely connected.
Removing the Antenna
Turn the antenna counter-clockwise to disconnect the antenna.
2.1.2 Hand Strap
Attach the hand strap as shown. There are two ways
to attach it.
2.1.3 Belt Clip
Attaching the Belt Clip
1. Put the belt clip on the back of the unit, and turn
the screw clockwise until it stops.
2. Confirm that the belt clip is securely attached.
Removing the Belt Clip
Turn the screw counter-clockwise to remove the belt clip.
■
■
■
NOTE:
This antenna has been designed very flexible. It
is softer than conventional ones but not a defect.
■
Installations
2.1
2.Accessories
2
15
2.1.4 Battery Pack
For the specifications and the charging procedures, please refer to "Battery
Packs"(page 54) and "Using the Chargers"(page 55).
Attaching the Battery Pack
Align the catches on the battery pack with the
grooves on the unit, and close the latch until it clicks.
Removing the Battery Pack
Push the latch in the direction of the arrow, and pull
out the battery pack.
■
■
Caution
• The battery pack isn't fully charged when shipped. It must be charged
before use.
• Charging should be conducted in a temperature range of 0ºC to +40ºC
(+32ºF to +104ºF).
• Don't modify, dismantle, incinerate or immerse the battery pack in the water
as this can be dangerous.
• Never short-circuit the battery pack terminals, as this can cause damage to
the equipment or lead to heating of the battery which may cause burns.
• Unnecessary prolonged charging (overcharging) can deteriorate battery
performance.
• The battery pack should be stored in a dry place where temperature is in
-10ºC to +45ºC (-14ºF to +113ºF) range. Temperatures outside this range
can cause the battery liquid to leak. Exposure to prolonged high humidity
can cause corrosion of metal components.
• Battery-packs are a consuming part. When its operating time becomes
considerably short after a normal charge, please consider that the pack is
exhausted and replace it with a new one.
• The battery pack is recyclable. Check with your local waste officials for
details on recycling options or proper disposal in your area.
2.Accessories
2
16
Charging the Battery Pack Using DC-Jack on the Unit
The unit can charge the EBP-65 and EBP-66 optional Ni-MH battery packs by
supplying DC power through the DC-jack on the unit using EDC-147/148 wall
chargers or an optional DC power supply (DC 12V~DC 16V, 1A or more: IEC/EN
60950-1 compliant) and a DC cable such as EDC-37.
1. Attach the battery pack by referring to "Battery Pack" (page 15).
2. Connect the AC adapter plug to the DC-jack on the
unit then connect the charger's adapter to the wall
outlet.
* AC adapter may look different.
3. Turn on the unit and set the battery charge
parameters. Please refer to "Set Mode" (page 42)
then:
* "Battery Charge Function" (page 46)
Select CHG-ON.
* "Battery Type Setting" (page 47)
Select BAT-NI.
4. After completing the settings, a flashing
appears on the display. Make sure the icon is
flashing then turn off the unit. It takes about 10
hours/30hours for EBP-65/66 respectively to
complete the charge.
IMPORTANT NOTE:
While this function is activated, without attaching a battery pack or the remaining
battery level is below the usable range, the unit turns on by just connecting the
DC source such as an adapter or a DC cable (without operating the power key).
■
Caution
• Li-ion battery packs can't be charged using DC-jack on the unit (Only NiMH battery packs can be charged).
• Risk of explosion, generation of heat or leak of chemicals inside if the
battery is replaced by an incorrect type. Use always the recommended
types of batteries in this manual only.
2.Accessories
2
17
2.1.5 Prevent Short Circuiting the Battery Pack
Be extra cautious when carrying the rechargeable battery pack; short circuiting will
produce surge current possibly resulting in fire.
NOTE:
• Please read the general safety instructions included in the optional accessories
to correctly and safely use them.
• EDC-147/148 can't be used as the adapter for operation. These adapters are for
charging purposes only.
• Chargers can't perform the correct charge when the AC voltage is unstable.
• flashes even EBP-65/66 aren't attached. To avoid short-circuit, never
activate this function when the pack isn't attached to the unit.
• Li-ion battery packs can't be charged in this way.
2.Accessories
2
18
2.1.6 Dry Cell Case (optional)
An EDH-34 is available for operation with using AA cells.
Lift up the catches on the top of the case to
remove the cover.
Place 6 AA cells, then close the cover in order of
then . Be sure that the cover is securely closed.
Use high-performance AA cells such as Alkaline or
Oxyride cells.
③
②
①
Caution About Handling Dry Cell Case:
• This dry cell case isn't water-proof.
• Be extra-cautious to the polarity of the cells (+)/(-). Misplacing cells may
result in leak, fire or explosion.
• Use new batteries of the same type and brand when placing them.
• Use of rechargeable cells is prohibited and the manufacturer declines any
responsibilities for damages/injuries that may cause to the users and their properties.
• It is recommended to clean the battery contacting terminals with a clean
dry cloth from time to time.
• Risk of explosion if batteries are replaced by an incorrect type.
• Batteries are recyclable. Please check the local rules for proper
recycle/disposal in your area.
Caution About Battery Charge Function:
The battery charge function is on by default. With this function on and the dry
cells installed, connecting the provided EDC-147/148 AC adapter or an optional
external power supply(stabilized power supply, cigarette lighter cable, etc.) to
the DC-jack on the unit may send current through the dry cells, resulting in
battery leak, heat or explosion. Referring to "Menu 18 Battery Charge Function"
on page 46, be sure to set this function off (select CHG-OF) when the unit is
equipped with the dry cells. However, there is no danger even if CHG-ON is
selected as long as no external power supply is connected to the unit.
2.Accessories
2
19
2.1.7 Battery-Level Icon
During the operation, a black battery icon indicates
that the battery-level is in usable range. When it
turns to empty, please charge the pack or replace the
cells with new ones.
3.Names and Operations of Parts
3
20
3. Names and Operations of Parts
Top and Front
VOL
V/M/C
S
Q
L
K
L
N
A
M
E
M
W
R
P
T
P
O
①
③
⑥
⑦
⑧
④
⑤
②
Dial
Microphone/
Speaker jack
TX/RX lamp
Speaker
Power key
Microphone
Display (LCD)
Keypad
Rotate the dial to select the frequency of operation, memory
channel, offset frequency, tone frequency, DCS code, Set mode
settings, and the characters for name-tags. Rotating the dial
while pressing the FUNC key increases or decreases the
frequency in 1MHz order.
For an optional speaker/Mic connection. Securely close the
cover for water-proof while the accessory isn't in use.
Lights green when the squelch is unmuted. Lights red during
transmission.
A speaker is built in.
Press the power key down for approximately one second to turn
on/off the unit.
Speak into the microphone from a distance of about 5cm (2").
Refer to "Display (LCD)" (page 23).
Refer to "Keypad" (page 22).
■
Names and Operations of Keys and Ports
3.1
Loading...