Spare parts list
V-chip password and software upgrade
This manual is the latest at the time of printing, and does not
include the modification which may be made after the printing,
by the constant improvement of product.
I. Safety Instru ctions
CAUTION
RISK OF ELECTRIC SHOCK
DO NO T OPEN
The l ightning fla sh w ith arro whead symb ol,
within an equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous
voltage” within the product’ s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
CAUTIO N: TO REDUCE THE RISK OF ELECTRIC
SHO CK, DO NOT REMOVE COVER (OR BACK). NO
USER-SERVI CEABLE PART S INSIDE. REFER
SERVICING TO QUALIFI ED SERVICE PERSONNEL
O NLY.
PRECAUTIONS DURING SERVICING
1. In a ddition to safety, other parts and assemblies are
speci fied for conformance with such regulations as
those applyi ng to spurious radiation. These must
also be replaced only with specified replacements.
Exampl es: RF converters, tuner units, antenna
selection switches, RF cables, noise-blocking
capacitors, noise-bl ocking filters, etc.
2. Use sp ecified internal Wiring. Note especially:
1) Wires covered with PVC tubing
2) Do uble insulated wires
3) Hig h voltage leads
3. Use specified i nsulating materials for hazardous
live pa rts. Note especially:
1) In sulating Tape
2) PVC tubing
3) Spa cers (insulating barriers)
4) Insulating sheets for transistors
5) Plastic screws for fixing micro switches
4. When replacing AC primary side compo nents
(tran sformers, power cords, n oise blocking
capacitors, e tc.), wrap ends of wires securely about
the te rminals before soldering.
5. Make sure that w ires do not contact heat generating
parts (he at sinks, oxide metal film resistors, fusible
resistors, etc.)
6. Check if replace d wires do not contact sharply edged
or po inted parts.
7. Make sure that foreign objects (screws, solder
drop lets, etc.) do not remain insi de the set.
MAKE YOUR CONTRIBUTION TO PROTECT THE
ENVIR ONMENT
Used batteries with the ISO symbol
for recycling a s well as small
accumu lators (rechargeable batteries), mini-batteries
(cell s) and starter batteries should not be thrown
into the garbage can.
Please leave them at an appropriate depot.
The excla mation po int wi thin a n equilateral
tri angle is intended to a lert th e user to the
presence of important operating and maintenance
(servici n g) instr u ct i o n s i n th e liter a tu re
accompanying the appliance.
W ARNING:
Before servicing this TV receiver, read the X-RAY
RADIATION PRECAUTION, SAFETY INSTRUCTION
and PRODUCT SAFETY NOTICE.
X-RA Y RADIATION PRECAUTION
1. Excessively high can prod uce potentially hazardous
X-RAY RADIATION. T o avoid such hazards, the high
volta ge must not exceed the specified limit. The
normal va lue of the high voltage of this TV receiver
is 2 7 KV at zero bean current (minimum brightness).
The high voltage must not exceed 30 KV under any
circu mstances. Each time when a re ceiver requires
servici ng, the high voltage should be checked. The
readi ng of the high voltage is re commended to be
reco rded as a part of the service record, It is
important to u se an accurate and reliable high
voltage meter.
2. The only source of X-RAY RADIATION in this TV
receiver is the picture tube. For con tinued X-RAY
RADIATION protectio n, the replacement tube must be
exactly the sa me type as specified in th e parts list.
3. Some parts in this TV receiver have special safety
related characteristics fo r X-RADIATION protection.
For continued safety, the parts replacement should
be under taken only afte r referring the PRODUCT
SAFETY NOTICE.
SAFETY IN STRUCTION
The se rvice should not be attempted by anyone
unfamiliar with the ne cessary instructions on this TV
receiver. The fo llowing are the necessary instructions
to be ob served before servicing.
1. An isolation transformer shoul d be connected in the
power li ne between the receiver and the AC line
when a service is performed on the primary of the
conve rter transformer of the set.
2. Comply wi th all caution and safety related provided
on th e back of the cabinet, inside the cabinet, on the
chassis or p icture tube.
3. T o avoid a shock hazard, always discharge the
pictu re tube's anode to the chassis g round before
removi ng the anode cap.
-2-
4. Completely discharge the high potential voltage of the
picture tube before handli ng. The picture tube is a
vacuum and if bro ken, the glass will explode.
5. When rep lacing a MAIN PCB in the cabinet, always
be certai n that all protective are installed properly
such as control knobs, adjustment co vers or shields,
barri ers, isolation resistor networks etc.
6. When se rvicing is required, observe the original lead
dressing. Extra precau tion should be given to assure
correct lead dressing in the high voltage area.
7. Keep wires away from high voltage or high te mpera
ture components.
8. Befo re returning the set to the customer, al ways
perform an AC leaka ge current check on the exposed
meta llic parts of the cabinet, such as anten nas,
termin als, screwheads, metal overlay, control shafts,
etc., to be sure the set is safe to operate without
danger of electrica l shock. Plug the AC line cord
directly to the AC outlet (do not use a line isolation
transformer d uring this check). Use an AC voltmeter
havin g 5K ohms volt sensitivity or more in the
following manner.
Conne ct a 1.5K ohm 10 watt resistor paralleled by a
0.15µF AC type capacitor, between a good earth
ground (water pipe, conductor etc.,) and the exposed
metallic parts, one at a time.
Measure the AC vol tage across the combination of
the 1 .5K ohm resistor and 0.15 uF capacitor. Reverse
the AC p lug at the AC outlet and repeat the AC
volta ge measurements for each exposed metallic
part.
The me asured voltage must not exceed 0.3V RMS.
This correspo nds to 0.5mA AC. Any value exceeding
this limit constitutes a potential shock hazard and
must be corrected immediately.
The resistance measurement should be done
betwe en accessible exposed metal parts and power
cord plug prongs with the power switch "ON". The
resi stance should be more than 6M ohms.
PRODUCT SA FETY NOTICE
Many e lectrical and mechanical parts in this TV
receiver have special safety-related characteristics.
These characteristics are offer passed unnoticed by
visual spection and the protection afforded by them
cannot necessari ly be obtained by using replacement
compon ents rates for a higher voltage, wattage, etc.
The replacemen t parts which have these special
safety characteristics are identified by marks on
the schematic diagram and on the parts list.
Before replacin g any of these components, read the
parts list in thi s manual carefully. The use of
substitute re placement parts which do not have the
same safety characteristics as specified in the parts
list may cre ate shock, fire, X-RAY RADIATION or
other h azards.
Good earth ground
such as the water
pipe, conductor,
etc.
AC Leak age Current Check
AC VOLTMETER
Place this probe
on eac h e xpos ed metallic
part
-3-
KAWA ELECTRONIC RESEARCH & DEVELOPMENT CENTRE
Product Specification
Reference No. : LC32ABHM
Revision : 0
Date : 2006.01.23Page : P.1 of 8
Model No. : LC32ABHM
Customer Model No. : LCT3226
Design Code : LC32AB
BOM No. : LC32AB
Artwork Ass'y No. : 580-L32ABHM-TU01L
Description : AKAL LCD TV 32” NTSC AC100V-240 V AC USA
Checked By: Electronic Engineer
Mechanical Engineer
Approved By: Engineering Manager
Approved By: PM Department Head
DOC Rev
NO.
0 Initial Release
The Latest Revision Details DATE
KAWA ELECTRONIC RESEARCH & DEVELOPMENT CENTRE
Reference No : LC32ABHM
Revision : 0
Date : 2006.01.23 Page : P. 2 of 8
General Description
1. Main features
Production Description
Panel Supplier and Model
Chips Solution
Market
1.1 VIDEO SECTION
Display size 32”/16:9
Display Resolution 1366 X 768
Pixel Pitch
Peak Brightness 550(nits)
Contract Ratio 1000:1, Typical (1/100 White Window, Dark Room)
View Angle Hor. And Vert. 170 degree
Color Deeps 16.7M Color (R / G/ B each 256 Scales)
PC Resolution Supporting VGA, SVGA, XGA,WXGA
HDTV Compatible 480i / 480p / 720p / 1080i
Progressive Scanning Yes
Film Mode Pull Down Yes
“GAMMA” Correction Yes
Color Temperature Control Yes
Comb Filter Yes
Second De-interlace for Sub picture No
Wide Mode
TV System NTSC M
Dual Tuner System No
AV Input Color System PAL /NTSC
PIP Basic mode (video on graphic mode,resolution 1024×768)
AKAL LCD TV 32” NTSC AC100V-240VAC USA
CHIMEI V320B1-L01
MK8205
USA
0.1730mmX0.5190mm
Full,Fill Aspect Ratio,Nonliner,LB to 16:9,
LB subtitles to 16:9 or Anamorphic
1.2 AUDIO SECTION
Audio Output Power 10W×2 Max.(8 ohm)
Sound Effect NO
Tone Control Yes
Channel +/- volume up/down menu input. standby : soft touch
Power on: Green
Standby: Red
English, FranÇais, Español
7. Safety standard UL/FCC/cUL
8. EMC standard 15 Parts of the FCC rules,CLASS B
9. Performance standard LCD-TV Standard
10. Accessories Battery 2pcs
User Manual 1pcs
AC Cable 1pcs
Remote Control 1pcs
The Accessories box 1pcs
E7501-051001
KAWA ELECTRONIC RESEARCH & DEVELOPMENT CENTRE
Reference No : LC32ABHM
Revision : 0
Date
Page : P. 5 of 8
Technical Data
1. Chassis MICO
TV AC 100-240 V, 50/60Hz 2. Power supply
Remote controller Battery 3V (UM-4/R03/AAA×2)
RF input NTSC M 3. TV system
Video input PAL/NTSC 3.58/NTSC 4.43
4. Receiving channels
TV
CATV
VHF-L : 2~6CH
VHF-H : 7~13CH
UHF : 14~69CH
1~125CH
: 2006.01.23
5. Intermediate
frequencies
6. Sca nn in g
7. AC plugUL
8. Panel V320B1-L01
9. Speaker Internal 8 ohm
10.Operating
temperature
11. Operating relative
humidity
12. Electrical &
optical
specification
13. Circuit diagram
drawing No.
15. Cabinet
16. Cabinet color
17. Packing 1 set per
18. Container stuffing
method
19. Dimension (mm) LCD-TV
(No packing)
Remote control unit
20. Net weight LCD-TV 15.5Kg (with Stand) approx.
Remote controller 70g (approx.)
Picture
or i zo nt a l (Hz ) 15625/15750
H
Ver ti ca l ( Hz ) 50/60
Fulfill all specifications
Accept
reproduction
Fulfill all specifications 45% ~ 75%
Accept picture/sound
reproduction
See the attachment 1.
RD/05/P/LC32HAB/CSI/02 REV: 01
picture/sound
45.75MHz
Plug
10W (m
15 C ~ 30 C
5 C ~ 33 C
20% ~ 80%
ax) ×2
LC32ABHM
988(W) x 514(H) x94(D)mm (w/o Stand)
988(W) x 582(H) x 268(D)mm (with Stand)
183(L) x 53(W) x 28(T)mm
21. Cell Defect Subject to Panel supplier specification
KAWA ELECTRONIC RESEARCH & DEVELOPMENT CENTRE
Reference No : LC32HAB001
Revision : 0
Date : 2006.01.23Page : P. 6 of 8
Attachment 1:Electrical & Optical Specification
No. Items Instruction TypicalLimit Unit
1 Video sensitivity For 30dB S/N 44 ≤51 dBuV
2 FM sound sensitivity For 30dB S/N 21 ≤35 dBuV
3 Color sensitivity For RF transmission 37 ≤40 dBuV
4 CCD sensitivity
5 Minimum NICAM threshold Without crackline noise N/A N/A dBuV
6 Stereo Channel Separation BTSC. 18 ≥15 dB
TV screen refreshes 40 times
number of mistakes≤8
43 ≤50 dBuV
AGC static characteristic
7
8 Selectivity Adjacent sound carrier 30 ≥28
Below adjacent sound carrier30 ≥30 dB
Adjacent picture carrier 45 ≥40
Up adjacent picture carrier 40 ≥30
9 IF rejection 55 ≥45 dB
10 Image rejection VHF 57 ≥45 dB
UHF 55 ≥40
11 AFT pull-in range ±1.0 ≥⏐±1.0⏐ MHz
12 Chroma sync pull-in range ±500 ≥⏐±200⏐ Hz
13 Color killer function -11 ≤-10 dB
14 Resolution
Video
Accept. Picture/Sound repr.90
RF
Vertical
Horizontal
Vertical 400 ≥400 Lines
PAL 300 ≥300 Lines Horizontal
NTSC 260 ≥240 Lines
PAL 410 ≥400 Lines
NTSC 320 ≥300 Lines
450 ≥450 Lines
≥90
dBuV
White
Coordination
16 View
Angle(Lo/3)
17 Overscan Cross hatch signal 96 94~98 %
Horizontal
Vertical
XW 0.295 0.295±0.02 15 Color
Y
W
Full Pattern
0.300 0.300±0.02
170
≥170
Degree
18 Picture position In all direction ±2 ≤⏐±3⏐ mm
19 H sync pull-in range ±400 ≥⏐±200⏐ Hz
20 V sync pull-in range 6 ≥6 Hz
21 Audio frequency response ±3dB ref. to 1KHz 0.15~12 0.2~12 KHz
KAWA ELECTRONIC RESEARCH & DEVELOPMENT CENTRE
Reference No : LC32HAB001
Revision : 0
Date : 2006.01.23Page : P. 7 of 8
22
Max Audio Output Power 7×2 ≥5.0×2 W
23 Audio output power
10% THD
24 THD Po=0.5W 0.5 ≤3 %
25 Signal to buzz ratio coeighting 50 ≥30 dB
26 Minimum volume hum coeighting 6 ≤10 mVrms
Operating 200 ≤200 W 38 Power consumpution
Stand by 3 ≤5 W
5m
The distance between
the tester and the
LCD-TV set is four
times as many as the
screen height
20 ≥15 Degree
No obvious vibration noise can be
heard
KAWA ELECTRONIC RESEARCH & DEVELOPMENT CENTRE
Reference No : LC32HAB001
Revision : 0
Date : 2006.01.23Page : P. 8of 8
Test Condition
All tests shall be performed under the following conditions unless otherwise specified
1 Picture Modulation 87.5%
2 Sound Modulation
3 Picture to Sound Ratio 10dB
4 Sound Artificial Load
Resistor
Video signal
5
6 Audio signal 1KHz sine wave 0.5Vrms
7 Other conditions:
A. Switch LCD-TV on and let it warm up for more than 30 minutes.
Viewing distance: 3H (H: Panel High) in front of LCD, about 2M.
Ambient light: ≤0.1 cd/ m
B. Brightness, Contrast, Saturation, Tint, sharpness set at normal.
C. Connect RMS volt meter to speaker terminals and adjust the LCD volume to get 500mW RMS
power at each terminals.
D. With image sticking protection of LCD module. The luminance will descend by time on a same
still screen and rapidly go down in 5 minutes, when measuring the color tracking and luminance
of a same still screen, be sure to accomplish the measurement in one minute to ensure its
accuracy.
E. Due to the structure of LCD module. The extra-high-bright same screen should not hold over 5
minutes for fear of branding on the panel.
F. RF test point: Video output.
27KHz Dev. For DK/I/BG
15KHz Dev. For M/N
8 ohm
Stair and Special
2
8 Note:
*(1) Now this project cannot fit the limited spec. the typical audio input level is 1.0 Vrms,
*(2) The audio out level is controlled by the volume level, the range is from 0 to 0.5Vrms.
1.Do not power on .
1.1 Please check AC cable if connect to AC plug.
Is true the connector don’t connect to AC plug. Please connect it.
2.2 Please check AC cable if connect to AC power.
Is true the AC cable don’t connect to AC power. Please connect it.
3.3 Please check power board of fuse if broken.
If the F1 fuse is broken, Please pull out the AC cable from AC power. Please check AC L
power and AC N ground by multimeter, The read number is infinite, the fuse is broke. then
look up power board if not burn out place. Is true it. Please change power board or be
changed power board.
2. The power on switch of green extinguish.
2.1 The power of led(indicator light) is red light, To touch power on key when indicator light
wink.
Is true that the power DC output have somewhere short circuit.
Please check connector J1,J21 and TV board J3,J1. If not connector direction is wrong.
Or the connect wire is direction is wrong.
3.The power is normal work ,but don’t backlight.
3.1 The indicator light work normal (green light ).
Please check Main board of transistor Q6 collect if not has +5v voltage.
Is true Q6 collect hasn’t +5v ,To check Q6 if fail.
3.2 Please check backlight of connector if not it direction is wrong or the connector of wire
compositor direction is wrong.
..The panel backlight(inverter) connector of wire compositor direction follow down:
.
.To control Backlight circuit diagram follow down:
PCB photo follow down:
To check connector J12 of the first pin if it have +5V voltage. It’s true , than to check power
board of +24v voltage ,It’s true. The panel of backlight board is fail. The change panel of
backlight board.
4.The screen don’t have picture But have backlight.
4.1 To check to panel of voltage ,To check main board of J10 of the twenty eighth ,ninth and
The panel of connector define diagram follow down:
Main board connect wire photo follow down:
4.2 To check to main board +5v voltage. To check to main board IC U34 of the first pin if +5v
voltage or check FB L51. It’s true +5V voltage, then check main board of F1
if +5v voltage .If not. Again to check Q17 of base is high level or low level .if high level
is OK. Is low level is fail.
The circuit diagram follow down:
PCB
5.The remote control don’t be control.
6.1 The check batteries of remote control if it run out of .
6.2 To check main board of connecter J14 of wire connect fastness and the connecter of
wire open.
The circuit diagram follow down:
6.The sound don’t output.
7.1 To check TV board +24v voltage ,It’s true not +24v voltage. Then check diode D11 if
open and IC U1,U3 short