Aiwa CSDEU-2000 Service manual

CSD-EU2000

EZ

SERVICE MANUAL

COMPACT DISC STEREO

RADIO CASSETTE RECORDER

MODEL CODE : 8ZCDB-0237(S)

BASIC TAPE MECHANISM : TN-21ZVC-1812 BASIC CD MECHANISM : KSM-213CDM

S/M Code No. 09-994-327-3N1

DATA

SPECIFICATIONS

Design and specifications are subject to change without

•

notice

.

2

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.

WARNING!

WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.

Caution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. Advarsel:Usynling laserståling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling.

VAROITUS!

Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.

VARNING!

Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

ATTENTION

L'utilisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.

ADVARSEL!

Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling.

This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.

CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1

LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT

Precaution to replace Optical block (KSS-213C)

Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode.

1) After the connection, remove solder shown in the right figure.

3

DISASSEMBLY INSTRUCTIONS

1. Remove the screws 1 (V+3-10 GLD*2), 2 (UT2+3-6*5) from the rear cabinet.

2. While pressing down the Q sound button, remove the rear cabinet . Open the hanger wide to the right and left, and remove it.

1

2

3. Remove the screws 3 (V+3-10 GLD*4).

3

4

4. Put the part of front cabinet shown by the arrow away from the H.P jack

5. Remove the CD block, the main board, and others from the front cabinet.

5

ELECTRICAL MAIN PARTS LIST

REF. NO PART NO. KANRI DESCRIPTION

NO.

IC 87-A20-955-010 IC,LA1828

87-070-416-010 IC,NJU7201 L55 87-A21-111-040 C-IC,M62495FP 87-A20-946-040 C-IC,MM1434XF 87-A21-193-010 IC,TA8227P

87-A21-145-040 C-IC,BA4560F-E2 87-A20-446-010 C-IC,LA9241ML 87-A20-459-010 C-IC,LC78622ED 87-A20-856-010 IC,BA6898S 8Z-CDB-651-010 C-IC,LC865516A-5L84

TRANSISTOR 89-319-233-080 TR,2SC1923 (0.1W)

87-026-572-080 TR,DTA114TS 87-026-215-080 TR,DTC114YS 89-109-521-080 TR,2SA952 (0.6W) 87-026-291-080 TR,DTC124XS

89-318-154-080 TR,2SC1815 (0.4W) 89-113-184-080 TR,2SA1318T 89-112-965-080 TR,2SA1296 (0.75W) 87-026-463-080 TR,2SA933S (0.3W) 89-320-011-080 TR,2SC2001 (15W)

89-318-155-080 TR,2SC1815 (0.4W) 87-026-462-080 TR,2SC1740 S(RS 0.3W) 89-110-155-080 TR,2SA1015(0.4W) 87-026-496-080 FET,2SJ103GR 89-328-786-080 TR,2SC2878B

87-026-217-080 TR,DTC124ES 87-026-235-080 CHIP-TR,DTC114EK 87-026-211-080 TR,DTA144EK 87-026-447-080 TR,2SC1740S R

DIODE 87-020-465-080 DIODE,1SS133 (110MA)

87-017-162-080 ZENER,HZS7C3L 87-017-148-080 ZENER,HZS6A1L 87-070-136-080 ZENER,MTZJ5.1B 87-027-607-080 ZENER,HZ7B3L

87-017-139-010 ZENER,HZS15-2 87-A40-466-080 ZENER,MTZJ2.7A 87-A40-465-090 DIODE,FR202

MAIN C.B C1 87-010-314-080 C-CAP,S 22P-50V

C2 87-010-316-080 C-CAP,S 33P-50 CH C3 87-010-314-080 C-CAP,S 22P-50V C5 87-010-148-080 CAP, CHIP S 75P SL C6 87-010-378-080 CAP, ELECT 10-16V

C7 87-018-208-080 CAP 0.047-50F C8 87-010-197-080 CAP, CHIP 0.01 DM C9 87-010-311-080 CAP 12P C10 87-010-197-080 CAP, CHIP 0.01 DM C11 87-010-148-080 CAP, CHIP S 75P SL

C12 87-010-314-080 C-CAP,S 22P-50V C13 87-010-148-080 CAP, CHIP S 75P SL C14 87-010-400-080 CAP, ELECT 0.47-50V C15 87-010-197-080 CAP, CHIP 0.01 DM C16 87-010-178-080 CHIP CAP 1000P

C17 87-016-669-080 C-CAP,S 0.1-25 K B C18 87-016-460-080 C-CAP,S 0.22-16 B C19 87-010-544-080 CAP, ELECT 0.1-50V C20 87-010-400-080 CAP, ELECT 0.47-50V C21 87-010-403-080 CAP, ELECT 3.3-50V

C22 87-010-197-080 CAP, CHIP 0.01 DM C24 87-010-197-080 CAP, CHIP 0.01 DM C25 87-010-197-080 CAP, CHIP 0.01 DM

REF. NO PART NO. KANRI DESCRIPTION

NO.

C26 87-016-460-080 C-CAP,S 0.22-16 B C27 87-016-460-080 C-CAP,S 0.22-16 B C28 87-010-194-080 CAP, CHIP 0.047 C29 87-010-194-080 CAP, CHIP 0.047 C30 87-010-248-080 CAP, ELECT 220-10V

C31 87-010-379-080 CAP, ELECT 22-16V C32 87-010-197-080 CAP, CHIP 0.01 DM C33 87-010-197-080 CAP, CHIP 0.01 DM C34 87-010-197-080 CAP, CHIP 0.01 DM C37 87-012-155-080 C-CAP 180P-50CH

C38 87-010-321-080 CHIP CAPACITOR,82P(J) C41 87-010-318-080 C-CAP,S 47P-50 CH C44 87-012-156-080 C-CAP,S 220P-50 CH C203 87-010-401-080 CAP, ELECT 1-50V C204 87-010-221-080 CAP, ELECT 470-10V

C205 87-010-263-080 CAP, ELECT 100-10V C206 87-010-248-080 CAP, ELECT 220-10V C206 87-010-248-080 CAP, ELECT 220-10V C210 87-010-198-080 CAP, CHIP 0.022 C211 87-010-260-080 CAP, ELECT 47-25V

C212 87-010-198-080 CAP, CHIP 0.022 C220 87-016-495-090 CAP,E 3300-25 SMG C230 87-010-405-080 CAP, ELECT 10-50V C231 87-010-404-080 CAP, ELECT 4.7-50V C232 87-010-263-080 CAP, ELECT 100-10V

C233 87-010-197-080 CAP, CHIP 0.01 DM C234 87-010-263-080 CAP, ELECT 100-10V C261 87-010-196-080 CHIP CAPACITOR,0.1-25 C262 87-010-384-080 CAP, ELECT 100-25V C263 87-010-385-080 CAP, ELECT 220-25V

C264 87-010-196-080 CHIP CAPACITOR,0.1-25 C265 87-010-236-080 CAP,E 1000-10 SME C301 87-010-405-080 CAP, ELECT 10-50V C302 87-010-405-080 CAP, ELECT 10-50V C303 87-010-405-080 CAP, ELECT 10-50V

C304 87-010-404-080 CAP, ELECT 4.7-50V C305 87-010-213-080 C-CAP,S 0.015-50 B C306 87-010-546-080 CAP, ELECT 0.33-50V C307 87-010-544-080 CAP, ELECT 0.1-50V C308 87-010-260-080 CAP, ELECT 47-25V

C309 87-010-263-080 CAP, ELECT 100-10V C310 87-010-544-080 CAP, ELECT 0.1-50V C311 87-010-546-080 CAP, ELECT 0.33-50V C312 87-010-213-080 C-CAP,S 0.015-50 B C313 87-010-404-080 CAP, ELECT 4.7-50V

C314 87-010-405-080 CAP, ELECT 10-50V C315 87-010-405-080 CAP, ELECT 10-50V C316 87-010-405-080 CAP, ELECT 10-50V C317 87-010-401-080 CAP, ELECT 1-50V C318 87-010-401-080 CAP, ELECT 1-50V

C319 87-010-197-080 CAP, CHIP 0.01 DM C320 87-010-405-080 CAP, ELECT 10-50V C321 87-010-260-080 CAP, ELECT 47-25V C322 87-010-402-080 CAP, ELECT 2.2-50V C325 87-010-400-080 CAP, ELECT 0.47-50V

C326 87-010-400-080 CAP, ELECT 0.47-50V C329 87-010-401-080 CAP, ELECT 1-50V C330 87-010-197-080 CAP, CHIP 0.01 DM C331 87-010-197-080 CAP, CHIP 0.01 DM C332 87-010-197-080 CAP, CHIP 0.01 DM

C333 87-010-197-080 CAP, CHIP 0.01 DM C334 87-010-404-080 CAP, ELECT 4.7-50V C335 87-010-406-080 CAP, ELECT 22-50 C336 87-010-401-080 CAP, ELECT 1-50V C337 87-010-178-080 CHIP CAP 1000P

C338 87-010-384-080 CAP, ELECT 100-25V C339 87-010-404-080 CAP, ELECT 4.7-50V C340 87-010-401-080 CAP, ELECT 1-50V C341 87-010-178-080 CHIP CAP 1000P C342 87-010-384-080 CAP, ELECT 100-25V

6

REF. NO PART NO. KANRI DESCRIPTION

NO.

C343 87-010-384-080 CAP, ELECT 100-25V C344 87-010-384-080 CAP, ELECT 100-25V C345 87-010-384-080 CAP, ELECT 100-25V C346 87-010-235-080 CAP,E 470-16 SME C347 87-010-384-080 CAP, ELECT 100-25V

C348 87-010-235-080 CAP,E 470-16 SME C351 87-010-401-080 CAP, ELECT 1-50V C355 87-010-384-080 CAP, ELECT 100-25V C401 87-010-178-080 CHIP CAP 1000P C402 87-012-157-080 C-CAP,S 330P-50 CH

C403 87-012-157-080 C-CAP,S 330P-50 CH C407 87-010-248-080 CAP, ELECT 220-10V C410 87-010-402-080 CAP, ELECT 2.2-50V C411 87-010-177-080 C-CAP,S 820P-50 SL C412 87-010-402-080 CAP, ELECT 2.2-50V

C413 87-012-158-080 C-CAP,S 390P-50 CH C415 87-010-406-080 CAP, ELECT 22-50 C416 87-010-404-080 CAP, ELECT 4.7-50V C417 87-010-384-080 CAP, ELECT 100-25V C418 87-010-402-080 CAP, ELECT 2.2-50V

C419 87-010-177-080 C-CAP,S 820P-50 SL C420 87-012-158-080 C-CAP,S 390P-50 CH C422 87-010-406-080 CAP, ELECT 22-50 C423 87-010-404-080 CAP, ELECT 4.7-50V C424 87-010-194-080 CAP, CHIP 0.047

C425 87-010-177-080 C-CAP,S 820P-50 SL C426 87-010-186-080 CAP,CHIP 4700P C427 87-010-404-080 CAP, ELECT 4.7-50V C428 87-010-260-080 CAP, ELECT 47-25V C429 87-012-153-080 C-CAP,S 120P-50 CH

C430 87-010-213-080 C-CAP,S 0.015-50 B C431 87-010-405-080 CAP, ELECT 10-50V C433 87-010-177-080 C-CAP,S 820P-50 SL C434 87-010-186-080 CAP,CHIP 4700P C435 87-010-404-080 CAP, ELECT 4.7-50V

C436 87-012-153-080 C-CAP,S 120P-50 CH C437 87-010-213-080 C-CAP,S 0.015-50 B C438 87-010-405-080 CAP, ELECT 10-50V C442 87-010-405-080 CAP, ELECT 10-50V C445 87-010-194-080 CAP, CHIP 0.047

C490 87-010-322-080 C-CAP,S 100P-50 CH C491 87-010-322-080 C-CAP,S 100P-50 CH CF1 87-A90-128-010 FLTR,AM IF CFAL-455 CF2 82-785-747-080 CF,MS2 GHY,R CF3 82-785-747-080 CF,MS2 GHY,R

CN210 87-049-919-010 CONN,3P EH V WHT CN220 87-049-469-010 CONN,4P V CN230 87-099-572-010 CONN,15P TUC-P15P-B1 CN320 87-049-469-010 CONN,4P V CN330 87-009-031-010 CONNECTOR, 3P

CN410 87-049-469-010 CONN,4P V CN420 87-009-030-010 CONNECTOR 2P PH M D3 87-A40-226-080 VARI-CAP,SVC251SPA J301 87-009-216-010 JACK, DIA 3.5 L2 87-A50-347-010 COIL,FM BPF EX

L3 87-A50-348-010 COIL,BAR ANT LW/MW (COI) L4 87-A50-345-010 COIL,FM RF EX L5 87-A50-343-010 COIL,FM OSC EX L7 87-A50-336-010 COIL,AM IFT (TOKO) L8 87-A50-335-010 COIL,FM IFT (TOKO)

L9 87-A50-334-010 COIL,FM DET (TOKO) L10 87-003-102-080 COIL, 10UH L16 87-A50-339-010 COIL,LW OSC (TOKO) L17 87-A50-337-010 COIL,AM OSC (TOKO) L310 87-003-098-010 COIL 2.2UH

L401 87-007-342-010 COIL,OSC 85K BIAS PVC1 87-A91-318-010 TUN-CAP,20P-140P E(TWD) S1 87-A91-175-010 SW,SL 2-4-3 SK43D01G06 S301 87-A90-815-010 SW,PUSH 2-2-6 SPUN19-S-501 S410 87-A91-173-010 SW,SL 2-2-3 SK23E01G04

REF. NO PART NO. KANRI DESCRIPTION

NO.

TC5 87-011-221-080 CAP, TRIMMER 30P TC6 87-011-220-080 TRIMMER CAP 20P VTC

CD C.B C501 87-010-197-080 CAP, CHIP 0.01 DM

C502 87-010-221-080 CAP, ELECT 470-10V C503 87-010-221-080 CAP, ELECT 470-10V C504 87-010-197-080 CAP, CHIP 0.01 DM C506 87-010-196-080 CHIP CAPACITOR,0.1-25

C507 87-010-196-080 CHIP CAPACITOR,0.1-25 C508 87-A10-381-080 CAP,E 1000-10 RE C509 87-010-197-080 CAP, CHIP 0.01 DM C510 87-010-197-080 CAP, CHIP 0.01 DM C511 87-010-263-080 CAP, ELECT 100-10V

C513 87-010-196-080 CHIP CAPACITOR,0.1-25 C514 87-010-196-080 CHIP CAPACITOR,0.1-25 C515 87-012-157-080 C-CAP,S 330P-50 CH C516 87-010-545-080 CAP, ELECT 0.22-50V C525 87-010-176-080 C-CAP,S 680P-50 SL

C527 87-010-186-080 CAP,CHIP 4700P C528 87-012-156-080 C-CAP,S 220P-50 CH C529 87-010-545-080 CAP, ELECT 0.22-50V C530 87-012-140-080 CAP 470P C531 87-010-374-080 CAP, ELECT 47-10V

C532 87-010-401-080 CAP, ELECT 1-50V C533 87-010-184-080 CHIP CAPACITOR 3300P(K) C535 87-010-145-080 C-CAP,S 1P-50 CH C536 87-010-312-080 C-CAP,S 15P-50 CH C538 87-010-196-080 CHIP CAPACITOR,0.1-25

C539 87-010-404-080 CAP, ELECT 4.7-50V C540 87-010-196-080 CHIP CAPACITOR,0.1-25 C541 87-010-405-080 CAP, ELECT 10-50V C543 87-010-401-080 CAP, ELECT 1-50V C545 87-010-197-080 CAP, CHIP 0.01 DM

C546 87-010-374-080 CAP, ELECT 47-10V C547 87-010-263-080 CAP, ELECT 100-10V C548 87-010-248-080 CAP, ELECT 220-10V C549 87-010-198-080 CAP, CHIP 0.022 C550 87-010-374-080 CAP, ELECT 47-10V

C551 87-010-178-080 CHIP CAP 1000P C552 87-010-197-080 CAP, CHIP 0.01 DM C553 87-010-248-080 CAP, ELECT 220-10V C554 87-010-263-080 CAP, ELECT 100-10V C555 87-010-403-080 CAP, ELECT 3.3-50V

C556 87-010-197-080 CAP, CHIP 0.01 DM C557 87-010-196-080 CHIP CAPACITOR,0.1-25 C558 87-010-197-080 CAP, CHIP 0.01 DM C559 87-010-315-080 C-CAP,S 27P-50 CH C560 87-010-263-080 CAP, ELECT 100-10V

C561 87-010-196-080 CHIP CAPACITOR,0.1-25 C562 87-010-196-080 CHIP CAPACITOR,0.1-25 C563 87-012-156-080 C-CAP,S 220P-50 CH C564 87-018-121-080 CAP, CER 150P-50V C565 87-010-263-080 CAP, ELECT 100-10V

C566 87-010-196-080 CHIP CAPACITOR,0.1-25 C569 87-010-404-080 CAP, ELECT 4.7-50V C570 87-018-134-080 CAPACITOR,TC-U 0.01-16 C571 87-010-248-080 CAP, ELECT 220-10V C572 87-010-196-080 CHIP CAPACITOR,0.1-25

C573 87-010-196-080 CHIP CAPACITOR,0.1-25 C575 87-010-312-080 C-CAP,S 15P-50 CH C576 87-010-312-080 C-CAP,S 15P-50 CH C578 87-018-134-080 CAPACITOR,TC-U 0.01-16 C579 87-010-263-080 CAP, ELECT 100-10V

C582 87-010-196-080 CHIP CAPACITOR,0.1-25 C583 87-010-405-080 CAP, ELECT 10-50V C584 87-012-156-080 C-CAP,S 220P-50 CH C585 87-010-405-080 CAP, ELECT 10-50V C586 87-012-156-080 C-CAP,S 220P-50 CH

7

REF. NO PART NO. KANRI DESCRIPTION

NO.

C587 87-010-322-080 C-CAP,S 100P-50 CH C589 87-010-322-080 C-CAP,S 100P-50 CH C590 87-010-322-080 C-CAP,S 100P-50 CH C591 87-010-322-080 C-CAP,S 100P-50 CH C592 87-010-322-080 C-CAP,S 100P-50 CH

C593 87-010-196-080 CHIP CAPACITOR,0.1-25 C601 87-010-313-080 CAP, CHIP 18P C602 87-010-313-080 CAP, CHIP 18P C603 87-010-197-080 CAP, CHIP 0.01 DM C604 87-010-196-080 CHIP CAPACITOR,0.1-25

C605 87-010-385-080 CAP, ELECT 220-25V C611 87-010-401-080 CAP, ELECT 1-50V C612 87-010-400-080 CAP, ELECT 0.47-50V C640 87-010-197-080 CAP, CHIP 0.01 DM C641 87-010-197-080 CAP, CHIP 0.01 DM

C644 87-018-134-080 CAPACITOR,TC-U 0.01-16 C655 87-010-178-080 CHIP CAP 1000P C656 87-015-627-080 C-CAP,1000P-50 B C657 87-010-197-080 CAP, CHIP 0.01 DM C658 87-015-819-080 CAPACITOR,0.01

C659 87-010-178-080 CHIP CAP 1000P C660 87-010-405-080 CAP, ELECT 10-50V C685 87-010-317-080 C-CAP,S 39P-50 CH C686 87-010-319-080 C-CAP,S 56P-50 CH C690 87-010-312-080 C-CAP,S 15P-50 CH

CN520 87-A60-424-010 CONN,16P V TOC-B CN610 87-099-751-010 CONN,16P V 9604SC CN630 87-009-030-010 CONNECTOR 2P PH M CN640 87-099-561-010 CONN,15P TUC-P15X-B1 L501 87-003-102-080 COIL, 10UH

L502 87-003-226-080 MICRO INDUCTOR 100UJ L504 87-003-102-080 COIL, 10UH L520 87-008-372-010 FILTER, EMI BL OIRNI L592 87-003-226-080 MICRO INDUCTOR 100UJ L593 87-003-102-080 COIL, 10UH

L601 87-003-143-080 COIL 4.7 UH L602 87-008-372-010 FILTER, EMI BL OIRNI SFR501 87-024-176-080 SEMI-FIXED RESISTOR, 100K X501 81-592-641-080 CERALOCK 16.93MHZ X601 87-030-273-010 VIB,XTAL 32.768K5PPM

X602 87-030-376-080 VIB,CER CSA5.76MG200

REF. NO PART NO. KANRI DESCRIPTION

FRONT C.B CN620 87-099-757-010 CONN,16P 9604S F

D601 87-A91-172-010 LED, SA36-11HWA-11.0MM RED D611 87-A40-622-010 LED,L-34HDSL RED D614 87-A40-622-010 LED,L-34HDSL RED S601 87-A90-164-080 SW,TACT SKQAB(N)

S602 87-A90-164-080 SW,TACT SKQAB(N) S603 87-A90-164-080 SW,TACT SKQAB(N) S604 87-A90-164-080 SW,TACT SKQAB(N) S605 87-A90-164-080 SW,TACT SKQAB(N)

KEY L C.B D641 87-A40-623-010 LED,L-34GDSL GRN

D642 87-A40-623-010 LED,L-34GDSL GRN S606 87-A90-164-080 SW,TACT SKQAB(N) S607 87-A90-164-080 SW,TACT SKQAB(N) S608 87-A90-164-080 SW,TACT SKQAB(N)

KEY R C.B

S611 87-A90-164-080 SW,TACT SKQAB(N) S620 87-A90-164-080 SW,TACT SKQAB(N) S621 87-A90-164-080 SW,TACT SKQAB(N)

MOTOR C.B M2 9X-262-576-910 MOTOR GEAR ASSY

PIN3 91-564-722-110 CONNECTOR 6P SW1 91-572-085-120 LEAF SW

AC C.B

C901 87-A11-132-080 CAP,TC U 0.01-50 K B C902 87-A11-132-080 CAP,TC U 0.01-50 K B C903 87-A11-132-080 CAP,TC U 0.01-50 K B C904 87-A11-132-080 CAP,TC U 0.01-50 K B CN910 87-049-919-010 CONN,3P EH V WHT

!

F901 87-A90-092-080 PROTECTOR,2.5A 491

NO.

• Regarding connectors, they are not stocked as they are not the initial order items. The connectors are available after they are supplied from connector manufacturers upon the order is received.

8

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

88

IC BLOCK DIAGRAM IC, LA1828

A

Resistor Code

Chip resistor

Wattage Type Tolerance 1/16W 1005 5% CJ

1/16W 1/10W

1/8W

1608 2125

3216

5% 5%

5%

TRANSISTOR ILLUSTRATION

Symbol

CJ CJ

CJ

Figure

Value of resistor

Form

L

Dimensions (mm)

t

W

0.55

Resistor Code

108 118

128

LW t

1.0 0.5 0.35 104

1.6 0.8 0.45 2 1.25 0.45

3.2

1.6

C

: A : A

IC, MM1434XF

E C B

2SA933 2SC1740 DTA144EK DTA114TS DTC114YS DTC124XS

E C B

2SA1015 2SA1296 2SA1318 2SC1815 2SC1923 2SC2001 2SC2878

B C E

2SB1370

S G D

2SJ103

E

B

DTC114EK

IC, TA8227P

IC, BA6898S

109

WIRING-1 (MAIN 1/2: INSERTED PARTS)

1

234567

KEY L C.B (INSERTED PARTS) KEY R C.B (INSERTED PARTS)

A

S607,D641

RADIO

B

S606,D642

CD

S608

TAPE

8

RPH

L

L3

EH

R

SW420

REC

SW

9

S611

3 - MODE

EQUALIZER

10

S621

VOL

11 12 13

S620

VOL

14

C

D

E

F

S001

BAND

FM AM

ANT - FM

S410

FM MODE/OSC

STEREO

MONO

24 20 15 13

1 5 10 12

1

PN410

4

1

24

510

20

TO/FROM CD C. B CN540

12

15

13

S301

Q SOUND

OFF

ON

1346

1

8

5

10

9

16

7 9 10 12

4 3 2 1

J301

1PN3204

SP1 L CH

SP2 R CH

1

2

1

4

5

8

1

2

1

4

8

5

1 5 10 15

2 1

G

MAIN C.B (INSERTED PARTS)

H

BATT C.B

BATTERY R14 x 8 DC12V

POWER C.B

TO/FROM CD C. B

CN640

PT901

1 PN220

M1

DECK

MOTOR

J601

2 1 3

AC

M

4

S1

DECK

SW

I

J

1211

SCHEMATIC DIAGRAM-1 (MAIN 1/2)

TO/FROM CD C. B (2/2) CN640

SW420

REC

SW

CN420

KEY L C. B

KEY R

C. B

RADIO

CD

R

3-MODE

EQJALIZER

V

10k

Q420, 421 PB SWITCH

R

LED DRIVELED DRIVE

CD

RADIO

TAPE B + SWITCH

PB AMP

D490 1N4148

Q409, 410

TAPE B + SWITCH

(1/2)

MAIN C. B (1/2)

TO/FROM MAIN C.B (2/2)

Q207, 206

TU B + SWITCH

1N4148

TO/FROM CD C.B (1/2) CN540

S301

QSOUND

ON

OFF

IC302

Q-SOUND

EQ AMP

U

4.7k

IC301

AUDIO SELECT/AMP

U

J301

PN320

IC303

AF

POWER

AMP

(L)

(R)

2.2µH

MUTE

R

L

RPH

AZIMU TH

ADJ.

EH

R486

Q430,431,432,433 BIAS SWITCH

PN410

R485

10k

R999

C445

BIAS OSC

4.7k

IC260

5.3V REG

Q222,223

AC IN DETECT

10k

0.047µF

LED

6.8k

5.6

DRIVER

5.5V REG

12K

R

7.8V REG

HZ73BL

Q226 SWITCH

2SD1370

7.8V REG

10k

R

U

R

Q270,271

M1

DECK

MOTOR

MOTOR DRIVE/SWITCH

TAPE MECHA BLOCK

S1

DECK

SW

PN220

Q210,211 201 B + SWITCH

POWER

C. B

F901 PROTECTOR 2.5A

4

10V REG

491 SERIES 60

BATT

R14 x 8

BATT C. B

AC 230V 50Hz

SIGNAL

: FM / PB

: AM / REC

AC

‘

AC

‘

C490

100P

D492

D493

1N4148

2SA933S

D491 1N4148

C491

100P

R491

5.6k

R492

CN410

22k

4.7k

D420

IN4148

D421

S410

FM MODE/OSC

STEREO

MONO

IN4148

56

5.6k

(1/2)

PB AMP

REC AMP

Q406,407,408 REC SWITCH

(2/2)

L401,C404

AC BIAS

ADJ.

Q402,403 BIAS LEVEL SWITCH

1413

WIRING-2 (MAIN 2/2: CHIP PARTS)

14

13 12 11 10 9 8

7

6

5

432

KEY R C.B (CHIP PARTS) KEY L C.B (CHIP PARTS)

1

A

B

C

D

MAIN C.B (CHIP PARTS)

E

F

G

H

I

J

1615

SCHEMATIC DIAGRAM-2 (MAIN 2/2)

MAIN C. B (2/2)

L4,PVC001C

FM TRACKING ADJ

L5,PVC001D

FM FREQ. ADJ

S410

FM MODE/OSC

STEREO

PVC

TUNING

PVC1A-1D

(LW)

(MW)

SW001

BAND

FM MW LW

L3,TC6

LW TRACKING ADJ

MW/LW/FM FRONT END

L7

AM IF ADJ

R

MONO

R

L8

FM IF ADJ

L3,PVC001A

MW TRACKING ADJ

L17,PVC001B

MW FREQ. ADJ

L16,TC5

LW FREQ. ADJ

SIGNAL

1817

WIRING-3 (CD/FRONT)

FRONT C. B

CD C. B (INSERTED PARTS)

E

TO/FROM MAIN C. B CN230

15

10 15

D

48

64 1

33

32

D MODEL

16

17

49

48

C

B

MOTOR C.B

TO/ FROM MAIN C. B

CN330

1

3

16 10 5 1

17 20 25 30 32

A

1 1

234567 234567

CD C. B (CHIP PARTS)

49

32

64

1

17

16

1

48

PICK UP ASSY

KSS - 213C

8 8

37

16

15

2

1

36

9 9

12

13

25

24

2

1

PN630

2

SW630 DOOR

10

SW

10

11 12 13 11 12 13

(INSERTED PARTS)

15

1016

125

S601

REPEAT

S603

D601

CD TRACK

D611

OP/BATT

D614

REPEAT

S602

STOP/

MEMORY

S605

PLAY/

PAUSE

FRONT C. B (CHIP PARTS)

S604

14 14

A

B

C

D

E

2019

SCHEMATIC DIAGRAM-3 (CD)

CD C.B (1/2)

CD MECHANISM

KSM-213CDM OPTICAL PICK UP BLOCK KSS-213C

1N4148

LED DRIVER

L520

F.B

TO/FROM CD C.B (2/2)

CN1

CN520

120k

150k 150k

3.9k

0.01

4.7k

1.0P

C535

47k

1k

4700P

22P

10uH

F.B

100uH

2.2uH

D510

1N4148

D511

1N4148

Q501,502 B + SWITCH

IC502

LC78622ED

10uH

0.01

TO/FROM CD C.B (2/2)

MOTOR C.B

M1

M2

SW1

PIN3

CN510

IC503 SPINDOLE/ SLED MOTOR DRIVER

REG

TO/FROM MAIN CD C.B (1/2) CN330

R

SIGNAL

: FM / PB

: AM / REC

2221

ELECTRICAL ADJUSTMENT

PRACTICAL SERVICE FIGURE

3 2

3

4 7

MAIN C.B

TC6

L8

8586 9

L17

L4

TC5

A

C

L16

B

D

L7

L5

L9

21 4

L3

LW MW

L401

< RADIO SECTION >

1. LW Frequency Range Adjustment

L16 ..................................................................... 145±2kHz

TC5.....................................................................295±4kHz

2. LW Tracking Adjustment

L3 .......................................................................... 150kHz

TC6......................................................................... 285kHz

3. MW Frequency Range Adjustment

L17 ..................................................................... 515±3kHz

PVC1B ........................................................... 1635±10kHz

4. MW Tracking Adjustment

L3 .......................................................................... 600kHz

PVC1A ................................................................. 1400kHz

5. AM IF Adjustment

L7 .......................................................................... 455kHz

6. FM Frequency Range Adjustment

L5 ................................................................ 87.4±0.1MHz

PVC1D ....................................................... 108.3±0.1MHz

7. FM Tracking Adjustment

L4 ...........................................................................88MHz

PVC1C ..................................................................108MHz

8. FM IF Adjustment

L8, 9 .....................................................................10.7MHz

< TAPE RECORDER SECTION >

9. Bias Adjustment

L401 ......................................................................... 60kHz

10. Azimuth Adjustment Condition: • Test tape: TTA-320

• Test point: PHONES JACK

• Adjustment location: Azimuth adjustment screw

Method: Play back the test tape and adjust so that the

output is maximum.

< RADIO SECTION >

< FM SECTION >

IHF Sensitivity: Less than 20dB (THD 3%) Signal to noise ratio: More than 55dB (Input 54dB) (at 98.0MHz) Distortion: Less than 3.0% (Input 54dB) (at 98.0MHz) Less than 5.0% (Input 120dB) Stereo separation: More than 18dB (at 98.0MHz) Intermediate frequency: 10.7±0.1MHz

< MW SECTION >

Sensitivity: (S/N 10dB) Less than 45dB Signal to noise ratio: More than 34dB (Input 74dB) Distortion: Less than 1.5% (Input 74dB) (at 1000kHz) AM Intermediate frequency: 455kHz±3.5kHz

< LW SECTION >

Sensitivity: Less than 54dB (S/N 10dB) Signal to noise ratio: More than 24dB (Input 74dB) Distortion: Less than 1.5% (Input 74dB) (at 200kHz)

< DECK SECTION >

Tape speed: 3000Hz±2% Distortion: Less than 2.0% (PB)

Less than 2.5% (REC/PC)

Signal to noise ratio: More than 44dB (AC)

More than 50dB (DC)

Erasing ratio: More than 45dB

0

2423

SCHEMATIC DIAGRAM-4 (FRONT)

CD C.B (2/2)

FRONT C. B

TO/FROM MAIN CD C.B (1/2) CN230

TO/FROM CD C.B (1/2)

TO/FROM MAIN CD C.B (1/2) CN230

R

RR

Q603,604,602

RESET

Q690

CLOCK SHIFT SWITCH

L651

SYSTEM CONTROL

P

1000P 1000P

1000P

1000P 1000P

1000P

OP/BATT

REPEAT

CD TRACK

1.5k

LED DEIVER

SEGMENT

DRIVER

S605 S604 S603 S602 S601

PLAY/

PAUSE

STOP/

MEMORY

REPEAT

CN640

SW630

(DOOR SW)

2625

IC DESCRIPTION IC, LC865508A

Pin No. Pin Name I/O Description

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18

O-SEG E

______________

O-SEG F

_______________

O-SEG G

—

I-RST

XT1 (IN)

NC

XT2 (OUT)

VSS

CF1 (IN)

CF2 (OUT)

VDD I-KEY0 I-KEY1

I-DECK

____________

I-CD SW

O-CLK SFT

NC

—

O

SEG E control.

O

SEG F control.

O

SEG G control. Not used.

I

Microprocessor reset input.

I

Connected to an external 32.768 kHz crystal oscillator. Not used.

O

Connected to an external 32.768 kHz crystal oscillator. GND.

I

Connected to an external 5.76 MHz ceramic filter.

O

Connected to an external 5.76 MHz ceramic filter. Microprocessor power supply (+5 V).

I

Key AD input. (AD)

I

Key AD input. (AD)

I

Deck status input. (AD)

I

CD door switch status input.

O

Main clock shift output. Not used.

Pin No. Pin Name I/O Description

42 43 44 45 46 47 48

NC

O-SEG DP

O-SEG A O-SEG B O-SEG C O-SEG D

NC

—

O O O O O

Not used. SEG DP control. SEG A control. SEG B control. SEG C control. SEG D control. Not used.

19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37

O-BASS LED

O-Qsound LED

O-SFT LED

I-DRF

I-WRQ

NC

I-REMO O-CD ON O-TU ON

O-P.CONT

NC

O-Qsound CONT

O-MUTE

O-DIGIT

O-RP LED

O-COIN

I-SQOUT

O-CQCK

O-RWC

—

O

BASS LED ON/OFF control output.

O

Q sound LED ON/OFF control output.

O

Clock shift A standby input.

I

CD RF level detection input.

I

CD subcode Q standby input. Not used.

I

Remote control input.

O

CD power control output.

O

TU power control output.

O

The main power supply control output. Not used.

O

Q sound ON/OFF control output.

O

Main mute output.

O

7-segment LED power supply control output.

O

REPEAT LED ON/OFF control output.

O

CD command output.

I

CD subcode Q input.

O

CD command/CLK for subcode.

O

CD read/write control output. 38 39 40 41

O-DATA O-CD FUNC LED O-TU FUNC LED O-TA FUNC LED

O

Data output to M62439FP.

O

LED ON/OFF control output for the CD function

O

LED ON/OFF control output for the TU function

O

LED ON/OFF control output for the TA function

2827

IC, LA9241ML

Pin No. Pin Name I/O Description

1

2

FIN2

FIN1

Pin to which external pickup photo diode is connected. RF signal is created by adding

I

with the FIN1 pin signal. FE signal is created by subtracting from the FIN1 pin signal.

I

Pin to which external pickup photo diode is connected.

10 11

12

13 14 15 16

17

3

4 5 6 7

8

9

E

F

TB

TE–

TE

TESI

SCI

TH TA

TD–

TD

JP TO FD

FD–

Pin to which external pickup photo diode is connected. TE signal is created by

I

subtracting from the F pin signal.

I

Pin to which external pickup photo diode is connected.

I

DC component of the TE signal is input.

I

Pin to which external resistor setting the TE signal gain is connected between the TE pin.

O

TE signal output pin. TES “Track Error Sense” comparator input pin. TE signal is passed through a band-

I

pass filter then input.

I

Shock detection signal input pin.

I

Tracking gain time constant setting pin.

O

TA amplifier output pin. Pin to which external tracking phase compensation constants are connected between

I

the TD and VR pins.

I

Tracking phase compensation setting pin.

I

Tracking jump signal (kick pulse) amplitude setting pin.

O

Tracking control signal output pin.

O

Focusing control signal output pin. Pin to which external focusing phase compensation constants are connected between

I

the FD and FA pins.

18

19

20 21 22 23 24 25

26

27 28

29 30, 31 32, 33

34

FA

FA–

FE

FE–

AGND

NC

SP

SPG

SP–

SPD

SLEQ

SLD

SL–, SL+

JP–, JP+

TGL

— —

Pin to which external focusing phase compensation constants are connected between

I

the FD– and FA– pins. Pin to which external focusing phase compensation constants are connected between

I

the FA and FE pins.

O

FE signal output pin.

I

Pin to which external FE signal gain setting resistor is connected between the FE pin. Analog signal GND. No connection.

O

Single ended output of the CV+ and CV– pin input signal.

I

Pin to which external spindle gain setting resistor in 12 cm mode is connected. Pin to which external spindle phase compensation constants are connected together

I

with SPD pin.

O

Spindle control signal output pin.

I

Pin to which external sled phase compensation constants are connected.

O

Sled control signal output pin.

I

Sled advance signal input pin from microprocessor.

I

Tracking jump signal input pin from DSP.

I

Tracking gain control signal input from DSP. Low gain when TGL = H.

35

TOFF

I

Tracking off control signal input pin from DSP. Off when TOFF = H.

29

Pin No. Pin Name I/O Description

36

TES

O

Pin from which TES signal is output to DSP.

37

38

39, 40

41

42

43

44 45 46 47 48 49 50 51 52 53 54 55

HFL

SLOF

CV–, CV+

RFSM

RFS–

SLC

SLI

DGND

FSC

TBC

NC DEF CLK

CL

DAT

CE

DRF

FSS

—

“High Frequency Level” is used to judge whether the main beam position is on top of

O

bit or on top of mirror.

I

Sled servo off control input pin.

I

CLV error signal input pin from DSP.

O

RF output pin. RF gain setting and EFM signal 3T compensation constant setting pin together with

I

RFSM pin. “Slice Level Control” is the output pin which controls the RF signal data slice level by

O

DSP.

I

Input pin which control the data slice level by the DSP. Digital system GND.

O

Output pin to which external focus search smoothing capacitor is connected.

I

“Tracking Balance Control” EF balance variable range setting pin. No connection.

O

Disc defect detector output pin.

I

Reference clock input pin. 4.23 MHz of the DSP is input.

I

Microprocessor command clock input pin.

I

Microprocessor command data input pin.

I

Microprocessor command chip enable input pin.

O

“Detect RF” RF level detector output.

I

“Focus Search Select” focus search mode (± search/+ search) select pin. 56 57 58 59 60 61 62 63 64

VCC2

REFI

VR LF2 PH1

BH1 LDD LDS

VCC1

— —

—

Servo system and digital system Vcc pin. Pin to which external bypass capacitor for reference voltage is connected.

O

Reference voltage output pin.

I

Disc defect detector time constant setting pin.

I

Pin to which external capacitor for RF signal peak holding is connected.

I

Pin to which external capacitor for RF signal bottom holding is connected.

O

APC circuit output pin.

I

APC circuit input pin. RF system Vcc pin.

30

IC, LC78622ED

Pin No. Pin Name I/O Description

1 2 3 4

DEFI

TAI

PDO

VVSS

—

I

Defect sense signal (DEF) input pin. (Connect to 0V when not used).

I

O

Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Phase comparator output pin to control external VCO. GND pin for built-in VCO. Be sure to connect to 0V.

For PLL.

5 6 7 8 9

ISET

VVDD

FR

VSS

EFMO

—

I

Pin to which external resistor adjusting the PD0 output current. Power supply pin for built-in VCO.

I

Pin for VCO frequency range adjustment.

Digital system GND. Be sure to connect to 0V.

O

EFM signal output pin.

For slice level control.

10 11

12, 13

14

EFMIN

TEST2

CLV+, CLV–

___

V/P

I I

Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.

O

Disc motor control output. Three level output is possible using command. Rough servo or phase control automatic selection monitoring output pin. Rough servo

O

EFM signal input pin.

at H. Phase servo at L. 15 16 17 18

19, 20

21

22

HFL

TES

TOFF

TGL

JP+, JP–

PCK

FSEQ

I

Track detect signal input pin. Schmidt input.

I

Tracking error signal input pin. Schmidt input.

O

Tracking OFF output pin.

O

Tracking gain selection output pin. Gain boost at L.

O

Track jump control signal output pin. Three level output is possible using command.

O

EFM data playback clock monitoring pin 4.3218 MHz when phase is locked in.

Sync signal detection output pin. H when the sync signal which is detected from EFM

O

signal and thesync signal which is internally generated agree. 23

VDD

—

Digital system power supply pin.

The pin is controlled by the serial data command from microprocessor. When

24-28

SL+ - PUIN

I/O

General purpose input/output pin 1 to 5.

the pin is not used, set the pin to the input terminal and connect to 0V, or alternately set the pin to output terminal and leave the pin open.

29

EMPH

O

De-emphasis monitor output pin. De-emphasis disc is being played back at H.

Pin No. Pin Name I/O Description

43 44 45 46 47 48 49 50

XVDD XOUT

XIN XVSS SBSY EFLG

PW

SFSY

—

Crystal oscillator power supply pin.

O

Pin to which external 16.9344 MHz crystal oscillator is connected.

I

—

Crystal oscillator GND pin. Be sure to connect to 0V.

O

Subcode block sync signal output pin.

O

C1, C2, single and dual correction monitoring pin.

O

Subcode P, Q, R, S, T, U and W output pin.

O

Subcode frame sync signal output pin. Falls down when subcode enters standby. Subcode read clock input pin. Schmidt input. (Be sure to connected to 0V when not in

51

SBCK

I

use.)

52

FSX

Pin outputting the 7.35 kHz sync signal which is generated by dividing frequency of

O

crystal oscillator. 53 54 55 56 57 58 59 60 61 62

63

WRQ RWC

SQOUT

COIN

___________

CQCK

________

RES

TST11

16M

4.2M

TEST5

______

CS

O

Subcode Q output standby output pin.

I

Read/write control input pin. Schmidt input.

O

Subcode Q output pin.

I

Command input pin from microprocessor.

I

Command input read clock or subcode read input clock from SQOUT pin

I

LC78622 reset input pin. Set this pin to L once when the main power is turned on.

O

Test signal output pin. Use this pin as open (normally L output).

O

16.9344 MHz output pin.

O

4.2336 MHz output pin.

I

Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.

Chip select signal input pin with built-in pull-down resistor. Be sure to connect to 0V

I

while it is not controlling. 64

TEST1

I

Test signal input pin without built-in pull-down resistor. Be sure to connect to 0V.

Note: The same potential must be applied to the respective power supply terminals. (VDD, VVDD, LVDD, RVDD, XVDD)

30 31

32, 33

34 35 36 37 38 39 40 41 42

C2F

DOUT

TEST3, TEST4

N.C.

MUTEL

LVDD LCHO

LVSS

RVSS

RCHO

RVDD

MUTER

—

— —

—

O

C2 flag output pin.

O

DIGITAL OUT output pin. (EIAJ format).

I

Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Not used. Set the pin to open.

O

L-channel 1-bit DAC.

O

L-channel mute output pin. L-channel power supply pin. L-channel output pin. L-channel GND. Be sure to connect to 0V. R-channel GND. Be sure to connect to 0V.

O

R-channel output pin.

R-channel 1-bit DAC.

R-channel power supply pin.

O

R-channel mute output pin.

3231

MECHANICAL EXPLODED VIEW 1/1

40

A

38

G

43

C

48

P.C. B

E

46

44

A

41

42

A

C

A

49

P.C. B

WIRE, ASSY

63

A

50

62

47

51

A

C

A

C

52

53

54

56

B

60

61

55

57

58

59

34

33

22

23

24

25

26

D

1

4

2

3

6

65

32

35

12

16

13

64

F

69

A

17

18

19

20

A

21

A

31

A

30

29

28

27

A

5

P.C. B

A

7

37

69

14

D

A

KSM-213CDM

45

TN-21ZVC1812

15

A

36

54

15

39

66

PLATE,COVER PT

P.C. B

A

45

A

13

10

8

9

11

12

P.C. B

A

3433

67

68

MECHANICAL PARTS LIST 1/1

REF. NO PART NO. KANRI DESCRIPTION

1 84-CD8-083-010 BADGE,AIWA 30.5-5.2 2.5LEAD 2 8Z-CDB-004-010 WINDOW,LED(EX) 3 8Z-CDB-042-010 PANEL,FRONT(U) 4 8Z-CDB-026-010 KEY,CD A 5 8Z-CDB-027-010 KEY,CD B

6 8Z-CDB-625-010 FF-CABLE, 16P 1.25 240MM FRONT 7 8Z-CDB-094-010 GRILLE,SPKR L (GRAY)<EZS> 7 8Z-CDB-118-010 GRILLE,SPKR L (L)<EZL> 8 8Z-CDB-006-010 LID,CASS 9 8Z-CDB-210-010 SPR-T,LID CASS

10 8Z-CDB-008-010 WINDOW,CASS 11 8Z-CDB-095-010 GRILLE,SPKR R (GRAY)<EZS> 11 8Z-CDB-119-010 GRILLE,SPKR R (L)<EZL> 12 84-CD5-216-010 BRACKET 13 84-CD5-215-010 GEAR

14 8Z-CDB-001-010 CABI,FRONT<EZS> 14 8Z-CDB-101-010 CABI,FRONT (L)<EZL> 15 88-CD8-622-010 SPKR,F 77 7OHM 3W 16 8Z-CDB-019-010 KEY,CASS PAUSE<EZS> 16 8Z-CDB-107-010 KEY,CASS PAUSE (L)<EZL>

17 8Z-CDB-021-010 KEY,CASS STOP<EZS> 17 8Z-CDB-109-010 KEY,CASS STOP (L)<EZL> 18 8Z-CDB-022-010 KEY,CASS FF<EZS> 18 8Z-CDB-110-010 KEY,CASS FF (L)<EZL> 19 8Z-CDB-023-010 KEY,CASS REW<EZS>

19 8Z-CDB-111-010 KEY,CASS REW (L)<EZL> 20 8Z-CDB-020-010 KEY,CASS PLAY<EZS> 20 8Z-CDB-108-010 KEY,CASS PLAY (L)<EZL> 21 8Z-CDB-018-010 KEY,CASS REC<EZS> 21 8Z-CDB-106-010 KEY,CASS REC (L)<EZL>

22 84-CT5-209-010 PLATE,MAGNET 23 87-036-368-010 MAGNET 24 8Z-CDB-215-010 HLDR,LID CD 25 88-CD9-210-010 BASE,CHUCK 26 88-CD9-211-010 RING,CHUCK

27 87-CD7-207-010 HLDR,LOCKER 28 82-CD8-212-010 SPR-T,CAM CD 29 87-CD7-206-010 DOOR,CD LOCKER 30 8Z-CDB-025-010 KEY,EQ<EZS> 30 8Z-CDB-112-010 KEY,EQ (L)<EZL>

31 8Z-CDB-016-010 KEY,VOL<EZS> 31 8Z-CDB-113-010 KEY,VOL (L)<EZL> 32 8Z-CDB-166-010 CHAS,CD EZ (L)<EZL> 32 8Z-CDB-047-010 CHAS,CD(U)<EZS> 33 8Z-CDB-009-010 WINDOW,CD

34 8Z-CDB-005-010 LID,CD<EZS> 34 8Z-CDB-097-010 LID,CD EU2000 EZ (L)<EZL> 35 8Z-CDB-211-010 SPR-T,LID CD 36 81-590-677-010 SWITCH LEAF 37 8Z-CDB-037-010 LENS,LED

NO.

38 8Z-CDB-014-010 ARM,MAIN HANDL<EZS> 38 8Z-CDB-115-010 ARM,MAIN HANDL (L)<EZL> 39 8Z-CDB-015-010 COVER, HANDLE<EZS> 39 8Z-CDB-116-010 COVER, HANDLE (L)<EZL>

!

41 8Z-CDB-048-010 KEY,FUNCT(U) 42 8Z-CDB-204-010 HLDR,KEY FUNC 43 88-CD9-207-010 COVER, AC SOCKET

!

45 8Z-CDB-208-010 HLDR,SPKR 46 88-CD8-209-010 SPR-C,BATT

47 8Z-CDB-067-010 CABI,REAR EZ<EZS> 47 8Z-CDB-161-010 CABI,REAR EZ (L)<EZL> 48 8Z-CDB-024-010 KEY,Q-SOUND 49 8Z-CDB-028-010 KNOB,SL BAND

50 8Z-CDB-162-010 WINDOW,TU EZ (L)<EZL> 50 8Z-CDB-050-010 WINDOW,TU(EZ)<EZS> 51 87-043-116-010 ANT,WHIP 52 8Z-CDB-007-010 LID,BATT<EZS> 52 8Z-CDB-105-010 LID,BATT (L)<EZL>

53 8Z-CDB-029-010 KNOB,SL ST/MN 54 88-CD8-222-010 SPR-P,DAMP CD 55 8Z-CDB-035-010 POINTER,TUNNING 56 8Z-CDB-222-010 PLATE,FM 57 8Z-CDB-209-010 HLDR,BAND

58 8Z-CDB-030-010 KNOB,RTRY TU 59 8Z-CDB-206-010 HLDR,PVC 60 8Z-CDB-220-010 GEAR,TUNING 61 8Z-CDB-623-010 FF-CABLE, 16P 1.0 140MM CD-RF 62 8Z-CDB-205-010 GEAR,PVC

63 8Z-CSA-202-010 HLDR,PCB 64 88-CH6-019-010 PANEL,CD 65 8Z-CDB-207-010 HLDR,LED 66 8Z-CDB-227-010 HLDR,PT 67 8Z-CDB-630-010 CONN ASSY,6P CD-MOTOR

68 8Z-CDB-634-010 CONN ASSY,3P CD 69 88-CT6-206-010 CUSHION,CD A 87-261-096-410 SCREW,V+3-10 GLD B 87-751-034-410 SCREW VT2+2-5 C 87-745-094-410 UT2+3-6

D 87-651-035-410 VT1 2-6 GLD E 87-661-096-410 SCREW,VFT1+3-10 F 87-741-096-410 UT2+3-10 G 87-741-074-410 UT2+2.6-8

REF. NO PART NO. KANRI DESCRIPTION

NO.

40 8Z-CDB-621-010 PT,E

44 87-A60-178-010 JACK,AC E W/SW

COLOR NAME TABLE

Basic color symbol Color Basic color symbol Color Basic color symbol Color

B Black C Cream D Orange G Green H Gray L Blue

LT Transparent Blue N Gold P Pink

R Red S Silver ST Titan Silver

T Brown V Violet W White WT Transparent White Y Yellow YT Transparent Yellow LM Metallic Blue LL Light Blue GT Transparent Green

LD Dark Blue DT Transparent Orange

35

TAPE MECHANISM EXPLODED VIEW 1/1

F

B3 LUG PLATE

G

1

E

2

R

3

8

10

J L

N

14

b

18

19

36

46

47

55

9

53

20

21

22

23

24

52

5

12

13

49

M

6

7

30

31

32

4

11

a

15 16

17

51

26

27

28

29

56

34

35

48

b

a

c

C

D

K

41

6

O

54

C

37

38

39

42

43

33

A

25

P

B

40

H

50

I

45

44

36

TAPE MECHANISM PARTS LIST 1/1

REF. NO PART NO. KANRI DESCRIPTION

NO.

1 S1-921-030-4A0 HEAD BASE 2 S1-821-030-070 AZIMUTH SPRING 3 S1-921-030-090 PANEL P SPRING 4 S1-921-260-050 GEAR PLATE SPRING 5 S1-921-265-020 GEAR PLATE ASSY

6 S1-921-140-370 P ARM COLLER 7 S1-921-140-340 P ARM 8 S1-921-030-110 HEAD PANEL 9 S1-921-143-160 BASE ASSY 10 S1-921-141-8A0 M CONTROL SPRING

11 S1-921-260-4A0 SENSING LEVER 12 S1-921-043-100 PINCH ROLLER ARM ASSY 13 S1-921-130-010 EJECT SLIDE LEVER 14 S1-921-141-3A0 P CONTROL SPRING 15 S1-921-140-550 PAUSE LEVER(E)

16 S1-921-140-120 PAUSE LEVER SPRING 17 S1-921-140-110 PAUSE STOPPER 18 S1-921-140-150 BUTTON LEVER SPRING(B) 19 S1-821-011-590 E KICK LEVER 20 S1-921-140-140 BUTTON LEVER SPRING(A)

21 S1-921-140-200 PR STOPPER 22 S1-921-140-090 SWITCH ACTUATOR 23 S1-921-140-080 PUSH BUTTON ACTUATOR 24 S1-921-140-190 PLAY BUTTON LEVER 25 S6-401-010-380 LEAF SWITCH MSW-1275

26 S1-921-140-040 REW BUTTON LEVER 27 S1-921-140-050 FF,BUTTON LEVER 28 S1-921-140-060 STOP BUTTON LEVER 29 S1-921-140-600 PAUSE BUTTON LEVER 30 S1-821-100-700 FF GEAR

31 S1-921-050-060 SENSOR 32 S1-921-053-030 TAKE UP REEL ASSY 33 S1-829-100-010 PACK SPRING 34 S1-921-053-040 SUPPLY REEL ASSY 35 S1-821-100-990 BACK TENSION SPRING

36 S1-921-140-030 REC BUTTON LEVER 37 S1-921-140-170 P.S.LEVER SPRING 38 S1-921-073-040 RF CLUTCH ASSY 39 S1-921-070-030 RF BELT 40 S1-921-260-020 CAM GEAR

REF. NO PART NO. KANRI DESCRIPTION

NO.

41 S1-921-140-160 E ACTUATOR SPRING 42 S1-921-093-030 FLYWHEEL ASSY 43 S1-921-090-040 MAIN BELT 44 S1-921-120-010 MOTOR PULLEY 45 S6-002-030-220 MOTOR EG530AD-2B

46 S6-209-100-100 E HEAD PH-K380-MS1 47 S1-921-030-050 MG ARM 48 S1-921-140-210 REC BUTTON LEVER SPRING 49 S1-821-100-690 RECORD SAFETY LEVER 50 S1-821-128-9A0 MOTOR BRACKET

51 S1-821-010-500 PLAY BUTTON LEVER SPRING 52 S6-201-011-110 HEAD,RP7442ES-0951 53 S6-401-011-520 LEAF SW MSW-1541F 54 S1-921-015-010 CHASSIS ASSY 55 S1-921-030-100 MG ARM SPRING

56 S1-921-020-010 REC ARM A S9-P04-200-310 C TAPPING SCREW 2-3 B S1-921-120-020 MOTOR COLLER SCREW C S9-B10-200-510 P TAPPING BIND SCREW M2-5 D S9-C07-204-510 SCREW,TAPPING(CAMERA)M2-4.5

E S9-P01-200-610 SCREW,M2-6 F S9-P01-200-310 SCREW,M2-3 G S9-F08-200-710 AZIMUTH SCREW M2-7 H S1-921-120-030 MB SCREW I S9-W02-300-100 P WASHER CUT 1.2-3.8-0.3

J S9-W02-500-100 P WASHER CUT 1.45-3.8-0.5 K S9-W01-400-100 P WASHER 2-3.5-0.4 L S9-W01-130-200 P WASHER 2.1-4-0.13 M S9-P08-203-010 PS TAPPING SCREW M2-3 N S9-P05-200-810 SCREW,S TAP 2-8

O S9-P04-200-410 C TAPPING SCREW M2-4 P S9-P04-200-510 C TAPPING SCREW M2-5 R S9-W13-000-100 Y WASHER PB 0.1T

37

CD MECHANISM EXPLODED VIEW 1/1

2

COVER

5

3

SPINDLE MOTOR (M1)

4

CD MECHANISM PARTS LIST 1/1

A

1

(M2)

MOTOR C.B

REF. NO PART NO. KANRI DESCRIPTION

NO.

1 9X-262-620-210 MOTOR CHASSIS ASSY 2 92-626-907-010 GEAR(A) 3 87-A90-468-010 PICK UP KSS-213C 4 92-626-908-010 SHAFT SLED 5 92-627-003-020 GEAR(B)(RP)

A 97-621-255-150 SCREW+P2-3

38

ACCESSORIES/PACKAGE LIST

REF. NO PART NO. KANRI DESCRIPTION

1 8Z-CDB-918-010 IB,EZ(9L)B

!

2 87-A80-081-010 AC CORD SET ASSY,EZ BLK

NO.

39

2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111

737004

Printed in Singapore

Aiwa CSDEU-2000 Service manual

Specifications and Main Features

Frequently Asked Questions

User Manual