How it Works
Aiwa
Loading...
CSD-EL55
Service Manual
9 pgs88.38 Kb0

Aiwa CSDEL-55 Service manual

Download
Page 1
CSD-EL55
HR(S),K(S), EZ(S)
SERVICE MANUAL
COMPACT DISC STEREO RADIO
CASSETTE RECORDER
.
BASIC TAPE MECHANISM : 6ZM-3YPR3NC BASIC CD MECHANISM : 3ZG-3E2N
S/M Code No. 09-996-333-4R2
REVISION
Page 2
SPECIFICATIONS
<Tuner section> FM Tuner Section
Tuning range 87.5 MHz to 108 MHz Antenna Rod antenna
AM (MW) Tuner Section
Tuning range 531 kHz to 1602 kHz (9 kHz step)
530 kHz to 1710 kHz (10 kHz step)
Antenna Ferrite bar antenna
AM (LW) Tuner Section [EZ, K Model]
Tuning range 153 kHz to 288 kHz Antenna Ferrite bar antenna
<Cassette deck section>
Track format 4 track, 2 channels stereo Frequency response Normal tape: 50 Hz - 12500 Hz Recording system AC bias Heads Deck 1: Playback head x 1
Deck 2: Recording/Playback head x 1
Erasure head x 1
<Compact disc player section>
Laser Semiconductor laser (λ = 780 nm) D-A converter 1 bit dual
[HR Model]
Power output 2.5 W + 2.5 W (10% T.H.D. /7Ω DC)
2.0 W + 2.0 W (DIN 1% Rated Power)
Power requirements DC 12 V using eight size C (R14)
batteries 110 - 120 V/220 - 240 V AC, switchable, 50/60 Hz
Power consumption 18 W
[EZ Model]
Power output 5 W + 5 W (DIN MUSIC POWER)
4.5 W + 4.5 W (10% T.H.D. /3.2 Ω DC)
3.3 W + 3.3 W (DIN 1% Rated Power)
Power requirements DC 12 V using eight size C (R14)
batteries 230 V AC, 50Hz
Power consumption 22 W
[K Model]
Power output 4.5 W + 4.5 W (10% T.H.D. /3.2Ω DC)
3.3 W + 3.3 W (DIN 1% Rated Power)
Power requirements DC 12 V using eight size C (R14)
batteries 230 V AC, 50Hz
Power consumption 22 W
<General>
Speakers 100 mm cone type Output PHONES (stereo minijack) Dimensions of main unit (W x H x D)
510 x 181 x 244 mm
Weight of main unit 4.6 kg (not including batteries)
• Design and specifications are subject to change without notice.
ACCESSORIES LIST
REF. NO PART NO. KANRI DESCRIPTION
NO.
1 8Z-CH1-907-010 IB,H(ECA)FM<HR> 1 8Z-CH1-908-010 IB,EZ(9L)FM<EZ> 1 8Z-CH1-909-010 IB,K(E)FM<K> 2 8Z-CK4-962-010 RC UNIT,RC-ZAT04 (VS)
! 3 87-050-076-010 AC CORD SET ASSY,E ! 4 87-099-726-010 PLUG,ADPTR CONV(K)<K>
! 4 87-099-789-010 PLUG,ADPTR IR44<HR>
REF. NO PART NO. KANRI DESCRIPTION
NO.
2
Page 3
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
Caution: Invisible laser radiation when open and interlocks defeated avoid expo­sure to beam. Advarsel:Usynling laserståling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainit­ulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylit­tävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.
ADVARSEL!
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.
CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1
LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT
Precaution to replace Optical block
(KSS – 213F)
Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode.
1) After the connection, remove solder shown in the right figure.
PICK-UP Assy P.C.B.
Solder
3
Page 4
ELECTRICAL MAIN PARTS LIST
REF. NO PART NO. KANRI DESCRIPTION
IC 87-A21-184-010 IC,TA2104AN
87-A21-185-040 C-IC,LC72121M 87-A21-103-040 C-IC,MM1454XFBE 87-A20-715-010 IC,M62439SP 87-A20-591-010 IC,BA5417
87-017-889-010 IC,NJM4558LD 87-017-804-010 IC,BU4052BC 87-070-282-010 IC,BU2092 8Z-CH1-622-010 IC,LC867132V-5L08 87-A20-459-010 C-IC,LC78622ED
87-070-416-010 IC,NJU7201 L55 87-A20-911-010 IC,RPM6938 87-A20-446-010 C-IC,LA9241ML 87-A21-093-010 IC,LA6541D 87-001-982-010 IC,TA7291S
TRANSISTOR 87-A30-091-080 FET,2SJ460
87-026-291-080 TR,DTC124XS 89-213-702-080 TR,2SB1370E 89-319-233-080 TR,2SC1923O(0.1W) 87-A30-092-080 FET,2SK439E/F<K,EZ>
87-026-447-080 TR,2SC1740S RS<K,EZ> 89-320-011-080 TR,2SC2001K(15W) 87-026-214-080 TR,DTA114YS (0.3W)<K,EZ> 87-026-215-080 TR,DTC114YS 87-026-462-080 TR,2SC1740 S(RS 0.3W)
89-318-155-080 TR,2SC1815GR(0.4W) 87-A30-090-080 FET,2SK2541 87-A30-197-080 TR,KTA1267GR 87-026-610-080 TR,KTC3198GR 87-A30-154-080 TR,RT1N441S
89-109-521-080 TR,2SA952K(0.6W) 87-026-245-080 TR,DTC114ES 89-112-965-080 TR,2SA1296GR(0.75W) 87-026-463-080 TR,2SA933SRS(0.3W) 89-113-187-080 TR,2SA1318TU
87-026-289-080 TR,DTC143XS 87-026-464-080 TR,DTC114TS (0.3W) 89-113-184-080 TR,2SA1318TU 87-026-486-080 TR,DTA144TS 87-026-502-080 DTC144TS
DIODE 87-070-345-080 DIODE,IN4148
87-017-139-080 ZENER,HZS15-2 87-017-161-080 ZENER,HZS7C2L 87-017-148-080 ZENER,HZS6A1L 87-A40-465-010 DIODE,FR202
87-017-072-080 ZENER,HZS3B1 87-A40-292-080 ZENER,DZ2.7L 87-017-159-080 ZENER,HZS7B3L
MAIN C.B C205 87-010-401-080 CAP, ELECT 1-50V
C206 87-010-401-080 CAP, ELECT 1-50V C210 87-010-374-080 CAP, ELECT 47-10V C211 87-010-405-080 CAP, ELECT 10-50V C212 87-010-405-080 CAP, ELECT 10-50V
C219 87-010-375-080 CAP,E 330-10 SME C220 87-010-405-080 CAP, ELECT 10-50V C221 87-010-263-080 CAP, ELECT 100-10V C223 87-010-405-080 CAP, ELECT 10-50V C251 87-010-400-080 CAP, ELECT 0.47-50V
C252 87-010-400-080 CAP, ELECT 0.47-50V C255 87-010-546-080 CAP, ELECT 0.33-50V
NO.
REF. NO PART NO. KANRI DESCRIPTION
C256 87-010-546-080 CAP, ELECT 0.33-50V C257 87-010-544-080 CAP, ELECT 0.1-50V C258 87-010-544-080 CAP, ELECT 0.1-50V C261 87-010-263-080 CAP, ELECT 100-10V C262 87-010-260-080 CAP, ELECT 47-25V
C269 87-010-402-080 CAP, ELECT 2.2-50V C270 87-010-402-080 CAP, ELECT 2.2-50V C271 87-010-401-080 CAP, ELECT 1-50V C272 87-010-401-080 CAP, ELECT 1-50V C275 87-010-382-080 CAP, ELECT 22-25V
C276 87-010-382-080 CAP, ELECT 22-25V C277 87-010-260-080 CAP, ELECT 47-25V C278 87-010-384-080 CAP, ELECT 100-25V C281 87-010-380-080 CAP, ELECT 47-16V C282 87-010-380-080 CAP, ELECT 47-16V
C283 87-010-236-080 CAP,E 1000-10 SME C284 87-010-236-080 CAP,E 1000-10 SME C291 87-010-401-080 CAP, ELECT 1-50V C305 87-010-263-080 CAP, ELECT 100-10V C306 87-010-263-080 CAP, ELECT 100-10V
C311 87-010-546-080 CAP, ELECT 0.33-50V C312 87-010-546-080 CAP, ELECT 0.33-50V C331 87-A10-171-010 CAP,CER 390P-50 K B C332 87-A10-171-010 CAP,CER 390P-50 K B C333 87-A10-173-010 CAP,CER 560P-50 K B
C340 87-010-382-080 CAP, ELECT 22-25V C343 87-A10-165-010 CAP,CER 120P-50 K B<K,EZ> C363 87-010-405-080 CAP, ELECT 10-50V C364 87-010-405-080 CAP, ELECT 10-50V C369 87-A10-163-010 CAP,CER 82P-50 K SL
C370 87-A10-163-010 CAP,CER 82P-50 K SL C373 87-010-401-080 CAP, ELECT 1-50V C374 87-010-401-080 CAP, ELECT 1-50V C382 87-010-401-080 CAP, ELECT 1-50V C383 87-010-248-080 CAP, ELECT 220-10V
C405 87-010-401-080 CAP, ELECT 1-50V C406 87-010-401-080 CAP, ELECT 1-50V C452 87-A10-170-010 CAP,CER 330P-50 K B C453 87-010-406-080 CAP, ELECT 22-50 C511 87-010-060-080 ELECTROLYTIC 100-16V
C512 87-010-385-080 CAP, ELECT 220-25V C514 87-010-248-080 CAP, ELECT 220-10V C520 87-010-405-080 CAP, ELECT 10-50V C521 87-010-453-010 CAP, ELECT 4700-25V C526 87-010-404-080 CAP, ELECT 4.7-50V
C527 87-010-401-080 CAP, ELECT 1-50V C528 87-010-221-080 CAP, ELECT 470-10V C529 87-010-263-080 CAP, ELECT 100-10V C530 87-010-248-080 CAP, ELECT 220-10V C536 87-010-386-080 CAP,E330-25 SME
C542 87-010-221-080 CAP, ELECT 470-10V C543 87-010-401-080 CAP, ELECT 1-50V C801 87-010-403-080 CAP, ELECT 3.3-50V C802 87-018-134-080 CAPACITOR,TC-U 0.01-16 C803 87-010-263-080 CAP, ELECT 100-10V
C804 87-010-248-080 CAP, ELECT 220-10V C805 87-018-134-080 CAPACITOR,TC-U 0.01-16 C806 87-010-374-080 CAP, ELECT 47-10V C807 87-018-131-080 CAP, CER 1000P-50V C809 87-010-248-080 CAP, ELECT 220-10V
C810 87-010-263-080 CAP, ELECT 100-10V C812 87-010-401-080 CAP, ELECT 1-50V C814 87-010-405-080 CAP, ELECT 10-50V C816 87-010-545-080 CAP, ELECT 0.22-50V C817 87-018-125-080 CAP, CER 330P-50V
C825 87-018-129-080 CAP, CER 680P-50V C829 87-018-133-080 CAPACITOR,CER 4700P-16V C830 87-018-123-080 CAP, CER 220P-50V C831 87-010-545-080 CAP, ELECT 0.22-50V C832 87-010-374-080 CAP, ELECT 47-10V
NO.
4
Page 5
REF. NO PART NO. KANRI DESCRIPTION
C833 87-010-401-080 CAP, ELECT 1-50V C834 87-018-199-080 CAP, CER 3300P C835 87-018-134-080 CAPACITOR,TC-U 0.01-16 C836 87-010-374-080 CAP, ELECT 47-10V C837 87-010-404-080 CAP, ELECT 4.7-50V
C838 87-018-209-080 CAP, CER 0.1-50V C840 87-018-139-080 CAP,1P-50 CH C842 87-018-149-080 CAP,TC-U 15P-50 CH C843 87-018-209-080 CAP, CER 0.1-50V C844 87-018-134-080 CAPACITOR,TC-U 0.01-16
C845 87-018-209-080 CAP, CER 0.1-50V C846 87-018-209-080 CAP, CER 0.1-50V C847 87-018-209-080 CAP, CER 0.1-50V C848 87-018-111-080 CAP, CERA-SOL SS 27P C850 87-018-127-080 CAP, CER 470P-50V
C851 87-018-123-080 CAP, CER 220P-50V C855 87-010-263-080 CAP, ELECT 100-10V C857 87-018-149-080 CAP,TC-U 15P-50 CH C858 87-018-149-080 CAP,TC-U 15P-50 CH C859 87-010-263-080 CAP, ELECT 100-10V
C860 87-018-209-080 CAP, CER 0.1-50V C861 87-018-209-080 CAP, CER 0.1-50V C862 87-010-248-080 CAP, ELECT 220-10V C865 87-010-404-080 CAP, ELECT 4.7-50V C866 87-018-209-080 CAP, CER 0.1-50V
C867 87-010-263-080 CAP, ELECT 100-10V C869 87-018-121-080 CAP, CER 150P-50V C870 87-010-544-080 CAP, ELECT 0.1-50V C875 87-018-134-080 CAPACITOR,TC-U 0.01-16 C876 87-010-236-080 CAP,E 1000-10 SME
C877 87-018-134-080 CAPACITOR,TC-U 0.01-16 C878 87-010-263-080 CAP, ELECT 100-10V C879 87-018-134-080 CAPACITOR,TC-U 0.01-16 C880 87-010-221-080 CAP, ELECT 470-10V C881 87-010-405-080 CAP, ELECT 10-50V
C882 87-010-405-080 CAP, ELECT 10-50V C883 87-018-123-080 CAP, CER 220P-50V C884 87-018-123-080 CAP, CER 220P-50V C889 87-018-209-080 CAP, CER 0.1-50V C891 87-018-134-080 CAPACITOR,TC-U 0.01-16
C892 87-010-221-080 CAP, ELECT 470-10V C893 87-018-134-080 CAPACITOR,TC-U 0.01-16 C894 87-018-119-080 CAP, CER 100P-50V C895 87-018-119-080 CAP, CER 100P-50V C896 87-018-119-080 CAP, CER 100P-50V
C897 87-018-119-080 CAP, CER 100P-50V C898 87-018-119-080 CAP, CER 100P-50V C899 87-018-209-080 CAP, CER 0.1-50V C901 87-018-134-080 CAPACITOR,TC-U 0.01-16 C902 87-010-263-080 CAP, ELECT 100-10V
C903 87-018-209-080 CAP, CER 0.1-50V C1004 87-018-131-080 CAP, CER 1000P-50V C1005 87-018-131-080 CAP, CER 1000P-50V C1006 87-018-131-080 CAP, CER 1000P-50V C1007 87-018-134-080 CAPACITOR,TC-U 0.01-16
C1008 87-018-134-080 CAPACITOR,TC-U 0.01-16 C1009 87-018-134-080 CAPACITOR,TC-U 0.01-16 C1011 87-018-131-080 CAP, CER 1000P-50V CN201 87-009-883-010 CONN,10P TKC-T H(F) CN202 87-009-883-010 CONN,10P TKC-T H(F)
CN203 87-A60-457-010 CONN,4P V TID-X CN301 87-099-832-010 CONN,8P S2M-8W CN302 87-099-827-010 CONN,3P S2M-3W CN401 88-802-052-430 CONN ASSY,5P ORN CN501 87-099-827-010 CONN,3P S2M-3W
CN801 87-A60-424-010 CONN,16P V TOC-B CN802 87-099-194-010 CONN,6P 6216V CN803 87-099-212-010 CONN,5P 6216 V FFC1 88-CD5-638-010 FF-CABLE, 16P 1.0 220MM FFC2 88-906-181-110 FF-CABLE,6P 1.25
NO.
REF. NO PART NO. KANRI DESCRIPTION
FFC3 88-905-141-210 FF-CABLE, 5P 1.25 ICP192 87-002-330-010 PROTECTOR IC,ICP-N5 J201 87-009-216-010 JACK, DIA 3.5 L3 87-003-102-080 COIL, 10UH L38 87-003-102-080 COIL, 10UH
L201 87-003-102-080 COIL, 10UH L331 87-007-342-010 COIL,OSC 85K BIAS L801 87-003-102-080 COIL, 10UH L804 87-003-152-080 COIL, 100UH L805 87-003-148-080 COIL, 33UH
SFR801 87-024-176-080 SEMI-FIXED RESISTOR, 100K X801 81-592-641-010 VIB,CER 16.93MHZ
FRONT C.B C435 87-015-819-080 CAPACITOR,0.01
C439 87-015-819-080 CAPACITOR,0.01 C501 87-010-754-080 CAP,E220-10 SRA 7L C503 87-015-677-010 ELECTROLYTIC CAPACITOR, 100U 6 C505 87-018-209-080 CAP, CER 0.1-50V
C506 87-A10-139-010 CAP,CER 18P-50 K CH C507 87-A10-140-010 CAP,CER 22P-50 K CH C508 87-018-114-080 CAP, CERA-SOL SS 39P C509 87-010-316-080 CAP, CERA-SOL SS 33P C510 87-A10-136-010 CAP,CER 10P-50 K CH
C511 87-015-819-080 CAPACITOR,0.01 C522 87-015-696-080 CAP,E 2.2-50 7L C523 87-015-694-080 CAP,E 0.47-50 7L C524 87-015-696-080 CAP,E 2.2-50 7L C561 87-010-060-080 ELECTROLYTIC 100-16V
C571 87-015-681-080 CAP,E 10-16 7L CN461 87-099-753-010 CONN,11P H 9604 CN501 87-009-880-010 CONN,10P TKC-T H(M) CN502 87-009-880-010 CONN,10P TKC-T H(M) CNA551 8Z-CH1-628-010 CONN ASSY,6P WHT
COP301 87-A60-114-010 CONN,4P H S2M-4WR D565 87-A40-162-010 LED,L-1154SRD FFC4 88-911-101-110 FF-CABLE,11P 1.25 L502 81-NWB-655-010 COIL,10UH TROIDAL LCD501 8Z-CH1-623-010 LCD,ZCH-1 4177-30PIN
R458 87-001-486-010 IC,ICP-N15 SW301 87-A90-095-080 SW,TACT EVQ11G04M SW302 87-A90-095-080 SW,TACT EVQ11G04M SW303 87-A90-095-080 SW,TACT EVQ11G04M SW304 87-A90-095-080 SW,TACT EVQ11G04M
SW305 87-A90-095-080 SW,TACT EVQ11G04M SW306 87-A90-095-080 SW,TACT EVQ11G04M SW307 87-A90-095-080 SW,TACT EVQ11G04M SW308 87-A90-095-080 SW,TACT EVQ11G04M SW309 87-A90-095-080 SW,TACT EVQ11G04M
SW310 87-A90-095-080 SW,TACT EVQ11G04M SW311 87-A90-095-080 SW,TACT EVQ11G04M SW312 87-A90-095-080 SW,TACT EVQ11G04M SW313 87-A90-095-080 SW,TACT EVQ11G04M SW395 87-A90-095-080 SW,TACT EVQ11G04M
SW396 87-A90-095-080 SW,TACT EVQ11G04M SW397 87-A90-095-080 SW,TACT EVQ11G04M X501 87-030-273-010 VIB,XTAL 32.768K5PPM X502 87-A70-018-080 VIB,CER 6.00MHZ MG200
LED C.B D601 87-A40-161-010 LED,L-1154SGD
D602 87-A40-161-010 LED,L-1154SGD D603 87-A40-161-010 LED,L-1154SGD D604 87-A40-161-010 LED,L-1154SGD D605 87-A40-161-010 LED,L-1154SGD
D606 87-A40-161-010 LED,L-1154SGD D607 87-A40-161-010 LED,L-1154SGD D608 87-A40-161-010 LED,L-1154SGD
NO.
5
Page 6
REF. NO PART NO. KANRI DESCRIPTION
NO.
D609 87-A40-161-010 LED,L-1154SGD D610 87-A40-161-010 LED,L-1154SGD
SWITCH C.B C391 87-A10-166-010 CAP,CER 150P-50 K B
C392 87-A10-166-010 CAP,CER 150P-50 K B CN391 88-802-042-640 CONN ASSY,4P YEL SW381 87-A90-798-010 SW,RTRY 1-2-24 EVQVENF0124B SW391 87-A90-095-080 SW,TACT EVQ11G04M
SW392 87-A90-095-080 SW,TACT EVQ11G04M SW393 87-A90-095-080 SW,TACT EVQ11G04M SW394 87-A90-095-080 SW,TACT EVQ11G04M
TUNER C.B C1 87-010-314-080 C-CAP,S 22P-50V
C2 87-010-314-080 C-CAP,S 22P-50V C3 87-010-314-080 C-CAP,S 22P-50V C5 87-010-196-080 CHIP CAPACITOR,0.1-25<HR> C5 87-A10-484-080 C-CAP,S 1-25V<K,EZ>
C6 87-010-312-080 C-CAP,S 15P-50 CH<K,EZ> C6 87-010-313-080 CAP, CHIP 18P<HR> C7 87-014-049-080 CAP,PP 470P-100 J C8 87-012-349-080 C-CAP,S 1000P-50 CH C10 87-010-197-080 CAP, CHIP 0.01 DM
C11 87-010-197-080 CAP, CHIP 0.01 DM C12 87-010-197-080 CAP, CHIP 0.01 DM C13 87-010-150-080 C-CAP,S 6P-50 CH C14 87-010-303-080 C-CAP,S 330P-50CH C15 87-012-349-080 C-CAP,S 1000P-50 CH
C16 87-010-380-080 CAP, ELECT 47-16V C17 87-010-198-080 CAP, CHIP 0.022-25 C18 87-015-819-080 CAPACITOR,0.01 C19 87-010-112-080 CAP, ELECT 100-16V C20 87-010-404-080 CAP, ELECT 4.7-50V
C21 87-010-197-080 CAP, CHIP 0.01 DM C22 87-010-197-080 CAP, CHIP 0.01 DM C23 87-010-197-080 CAP, CHIP 0.01 DM C24 87-010-303-080 C-CAP,S 330P-50CH<K,EZ> C25 87-012-141-080 CAP, S 0.22-50V
C27 87-A10-484-080 C-CAP,S 1-25V C28 87-010-196-080 CHIP CAPACITOR,0.1-25 C29 87-010-196-080 CHIP CAPACITOR,0.1-25 C30 87-010-213-080 C-CAP,S 0.015-50 B<HR> C30 87-010-214-080 C-CAP,S 0.018-25<K,EZ>
C31 87-010-213-080 C-CAP,S 0.015-50 B<HR> C31 87-010-214-080 C-CAP,S 0.018-25<K,EZ> C33 87-010-401-080 CAP, ELECT 1-50V C34 87-010-401-080 CAP, ELECT 1-50V C35 87-015-819-080 CAPACITOR,0.01
C36 87-010-112-080 CAP, ELECT 100-16V C37 87-010-197-080 CAP, CHIP 0.01 DM C38 87-010-380-080 CAP, ELECT 47-16V C39 87-010-404-080 CAP, ELECT 4.7-50V C40 87-010-197-080 CAP, CHIP 0.01 DM
C41 87-012-349-080 C-CAP,S 1000P-50 CH C42 87-012-349-080 C-CAP,S 1000P-50 CH C43 87-012-349-080 C-CAP,S 1000P-50 CH C44 87-010-311-080 CAP 12P C45 87-010-312-080 C-CAP,S 15P-50 CH
C46 87-010-197-080 CAP, CHIP 0.01 DM C47 87-010-197-080 CAP, CHIP 0.01 DM C48 87-010-197-080 CAP, CHIP 0.01 DM C49 87-012-199-080 C-CAP,S 220P-50V CH C51 87-010-312-080 C-CAP,S 15P-50 CH<K,EZ>
C52 87-010-197-080 CAP, CHIP 0.01 DM<K,EZ> C53 87-010-197-080 CAP, CHIP 0.01 DM<K,EZ> C54 87-014-055-080 CAP,PP 820P-100 J<K,EZ> C55 87-010-197-080 CAP, CHIP 0.01 DM<K,EZ>
REF. NO PART NO. KANRI DESCRIPTION
NO.
C71 87-010-197-080 CAP, CHIP 0.01 DM<HR> C71 87-015-819-080 CAPACITOR,0.01<K,EZ> C72 87-010-196-080 CHIP CAPACITOR,0.1-25 C73 87-010-196-080 CHIP CAPACITOR,0.1-25 C78 87-010-196-080 CAP,CER 0.1-16V<K,EZ>
CF2 82-785-747-080 CF,MS2 GHY,R CF3 82-785-747-080 CF,MS2 GHY,R CF4 87-A91-094-010 FLTR,CDA10.7 MG80A CN5 87-099-854-010 CONN,6P CN6 87-A60-111-010 CONN,5P V S2M 5W
D3 87-A40-616-070 VARI-CAP,SVC384(S/T) D4 87-A40-615-070 VARI-CAP,KV1311NT D5 87-A40-615-070 VARI-CAP,KV1311NT L2 88-CD6-655-010 COIL,FM5MM*3.5T L3 87-A91-095-010 BAR-ANT,MW FOR 2B(SYN)<HR>
L3 87-A91-096-010 BAR-ANT,MW/LW FOR 3B(SYN)<K,EZ> L4 87-A50-420-010 COIL,MW OSC(SYN) L5 87-A50-424-010 COIL,FM RF EX(SYN) L6 87-A50-427-010 COIL,FM OSC EX(SYN) L7 87-A90-733-010 AM IFT W/C.F
L8 87-005-849-080 COIL,10UH(CECS) L9 87-005-849-080 COIL,10UH(CECS) L51 87-A50-421-010 COIL,LW OSC(SYN)<K,EZ> TC1 87-011-220-080 TRIMMER CAP 20P VTC TC51 87-011-233-080 TRIMER,50P VCT54<K,EZ>
X1 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309
LOADING MOTOR C.B M1 87-045-305-010 MOTOR,RF-500TB DC-5V(2MA)
SW1 87-036-110-010 SW,MICRO SPPB62 SW2 87-036-110-010 SW,MICRO SPPB62
CD MOTOR C.B M2 87-045-358-019 MOT,RF-310TA 43
M3 87-045-356-019 MOT,RF-310T 30 SW1 87-A90-042-010 SW,LEAF MSW 17310 MVPO
DECK C.B M4 87-045-347-019 MOT,SHU 2L 70
SFR1 87-024-581-019 SFR,3.3K DIA6H K0A SOL1 82-ZM1-635-010 SOL ASSY,23 SOL2 82-ZM1-635-010 SOL ASSY,23 SW1 87-036-110-010 SW,MICRO SPPB62
SW2 87-036-110-010 SW,MICRO SPPB62 SW3 87-036-110-010 SW,MICRO SPPB62 SW4 87-036-110-010 SW,MICRO SPPB62 SW5 87-036-110-010 SW,MICRO SPPB62
RELAY C.B
POWER C.B
!F701 87-035-190-010 FUSE,T2A 250V<HR> !F701 87-035-139-010 FUSE,T2.5AL 250V<K,EZ> !FC701 87-A90-160-080 FUSE CLAMP,FC 51F !FC702 87-A90-160-080 FUSE CLAMP,FC 51F
BATT C.B
6
Page 7
Chip resistor
No1234567891011121314 COM1 COM1 –– –– TAPE W1 ROCK W3 QSU 1h 1a 2f 2h 2a VOL COM2 –– COM2 –– TUNER MEMO POP W4 1f 1g 1b 2e 2g 2b S8 COM3 –– –– COM3 CD –– JAZZ W5 1e 1d 1c 2d 2i 2c P1
No 18 19 20 21 22 23 24 25 26 27 28 29 30 31 COM1 4a 4b RAN 5a 5b 6f 6a kHz MHz 7a S3 W6 CLO REC COM2 4g 4c 5f 5g 5c 6e 6g 6b 7f 7g 7b W7 TIM S6 COM3 4d P2 5e 5d P3 P4 6d 6c 7e 7d 7c W8 SLE S5
15 16 17
T-B 1 W2
3h 3b,c 4f
3i 3g 4e
32 33 S2 STE S4 MONO S7 S1
Wattage Type
1/16W 1/10W 1/8W
/ CHIP RESISTOR PART CODE
Chip Resistor Part Coding
8
8
Resistor Code
Tolerance
1608
2125
3216
5% 5% 5%
Symbol
CJ CJ CJ
Figure
Value of resistor
/ Diamensions (mm)
/ Form
L
t
W
1.6
3.2
LCD DISPLAY
Resistor Code : A
W
0.8
1.25
1.6
0.45
0.45
0.55
t
108 118 128
L
2
TRANSISTOR ILLUSTRATION
2SA952 2SA933S 2SK439 2SJ460 2SB1370 2SA1296 DTA114YS 2SK2541 2SA1318 DTA144TS 2SC1740 DTC114ES 2SC1815 DTC114TS 2SC1923 DTC124XS 2SC2001 DTC144TS KTC3198 RT1N441S
DTC114YS DTC143XS KTA1267
SDG GSD ECB ECB
BCE
87
Page 8
WIRING-1 (MAIN-CENTER, L SECTION)
1
234567
8
9
10
11 12 13
14
J201
A
B
NOTE
RXXX CXXX CXXX
,
,
JWXXX
A MAIN (CENTER)C. B
SP2
(RCH)
RED
WHT
WHT
RED
WHT
134
RED
WHT
RED
SP1
(LCH)
A MAIN (L)C. B
E
E
C
B
C B
E
B
C
C
B
E
PHONES
E C B
TO J
POWER C.B
CON501
13
C
TO PICK UP ASSY
CON1
FFC1
116
D
CN801
E C B
BCE
E
2 6 10 14 16
15 91315
6
1
CN802
FFC2
TO G
CON2
CD MOTOR C.B
134
E C B
E C B
15 13 11
9 7 5 3
1
17
16
49
IC801
64
48
510
1
20 25
30
45 40 33
60
55
49
32
35
16
IC802
48
17
45 40
BCE
20 25
6
5
2
1
1
30
3
28
5 7
9
11
30
32
33
35
B
E
C
C
E
B
13 15
B C E
26 24
22
20 18
16
E C B
1
2 4
5
CN803
BLU
1
FFC3
5
BCE
B C E
TO F
LOADING
MOTOR C.B
CON3
357910
1917151311
135 8
IC201
16 13 11 9
1
20
D530
ICP192
BCE
13
E C B
E C B
1
2
5
6
9
10
TO B
FRONT C.B
CN501
F
510
1
64
60
55
G
TO A MAIN (R)C.B JW49~60,64~81
H
9
I
7
5
3
1
J
TO A MAIN (R)C. B B
109
Page 9
SCHEMATIC DIAGRAM-1 (MAIN-CD SECTION)
1211
Page 10
WIRING-2 (MAIN-R, TUNER SECTION) <For HR Model>
1
234567
NOTE
8
9
10
11 12 13
14
A
A MAIN(R) C. B
RXXX CXXX
,
,
CXXX
B
ECB BCE
3
C
CON301
TO DECK2
CN301CN302
1
78
6
4
D
ECB
JWXXX
E
ECB
C B
BCE
FM ROD ANT.
L38
3
1
SDG
578
<HR,EZ>
GDS
E TUNER C. B
WHT
BLK
C1010
S D G
13
L3
SDG
L003
(AM BAR ANT.)
BLK
GRN
RED
JW49~59
B C
CON302
E
TO I RELAY C. B
E
B C E
BCE
E C
B
B
C E
F
G
ECB ECB
13578
13578
BCE
911131516
ECB
13578
BCE
135
TO A MAIN(CENTER) C. B
E C B
BLK BLK BLK BLK
ORG
1 3
1 3
5
5
TO A
BLU
MAIN
(CENTER) C. B
A
H
R075
R074
R073
BCE
BCE
C071
Q001
C023
R012
R011 C022
R013
C047
ECB
R018
R019
C073
D002
C072
CN004 CN003
R072
C021
R010
CF002
C099
R030
R029
R028
R027
R001
C017
C032
C001
C002
R038
R009
C018
R016
C045
L002
C003
R008
3157911
C011
C046
C030
12
C031
C029
R017
IC002
12
9 7
5 3 1
C028
C044
R025
151719212324 13
13
17 19
21
24
C008
C027
C013
C043
C035
R024
C040
C037
L005
R005
C025
R014
C042
R033
C009 R004
C012
C049
C098
C041
R023
C010
C014
C015
R022
D004
C048
R006
R031
R032
R002
TP1 (VT)
R021
R076
R077
C005 R003 C006
RED GRN
WHT BLK
I
J
TO B FRONT C. B
CN502
9
10
7
5
1
2
10 12 14 16 18
13579
JW60,64~81
TO A MAIN(CENTER) C. B
13 56
TO B FRONT C. B
CNA551
1413
Page 11
SCHEMATIC DIAGRAM-2 (MAIN-AMP SECTION)
C1010
0.01 <HR,EZ>
1615
Page 12
WIRING-3 (MAIN-R, TUNER SECTION) <FOR EZ, K Models>
1
A
234567
A MAIN(R) C. B
NOTE
RXXX CXXX
8
9
10
,
11 12 13
L003(MW/LW BAR ANT.)
MW LW
14
,
B
ECB BCE
3
1
C
CON301
TO DECK2
D
CON302
E
TO I RELAY C. B
78
4
CN301CN302
C342
C343
Q321
R386
6
B C E
E C B
BCE
F
G
ECB ECB
H
ECB
JWXXX
BLK1
ECB
E C B
BCE
FM ROD ANT.
WHT1
L38
13
578
S D G
13
L3
B
B
C
C
E
E
SDG
E C B
13578
SDG
GDS
13578
911131516
BCE
ECB
13578
BCE
135
E TUNER C. B
BLK
BLK2 BLK1
JW49~59
R073
C073
TO A MAIN(CENTER) C. B
E C B
BLK BLK BLK BLK
ORG
1 3
5
1 3
5
TO A
BLU
MAIN
(CENTER) C. B
A
R075
R074
BCE
BCE
C071
C023 R012 R011
C022
ECB
R013
C047
R019
R072
C021
R018
C075
C072
R030
R029
R010
C927
R028
R027
R001
CF002
R026
C930
C001
C017
C018
CF004
C928
R009R038
R016
12
C003
31 5 7 9 11 12
9 7
5 3 1
C045
L002
C002
C011
R057
C024
C030
R017
IC002
C046
C031
C029
R025
C044
C008
R008
24
1517192123
13
C043
13
17 19
21 24
C035
R024
R033
C014
C040
C037
C013
C025
C027 C028
R014
C049
C042
C012
C015
C041
R022
R004
R023
C010
R006
WHT2
WHT1
R051
C048
C052
C053
R021
R099
E
C
B
R056
R077
R031
C006
BCE
R002
R053
BCE
R054
R076
BLK2
C051
C005
R003
R032
R055
WHT2
C055
B C E
CXXX
R385
9
10
I
J
TO B FRONT C. B
7
5
1
2
10 12 14 16 18
13579
JW60,64~81
TO A MAIN(CENTER) C. B
TO B FRONT C. B
1356
CNA551
CN502
1817
Page 13
SCHEMATIC DIAGRAM-3 (TUNER SECTION) <FOR EZ, K Models> SCHEMATIC DIAGRAM-4 (TUNER SECTION) <FOR HR Model>
C930 33P
C928 33P
C927 33P
C075 0.01
2019
Page 14
WIRING-4 (FRONT SECTION)
1
A
234567
NOTE
RXXX CXXX
8
B FRONT C. B
SW311
,
CD OPEN TUNING TUNING
9
10
SW306 SW303 SW305 SW304 SW307 SW302
PLAY/PRESET
/DIR(DECK1)
11 12 13
STOP/
CLEAR
PAUSE/
SET
REC/
REC MUTE
SW313
REV
MODE
SW312
SYNCHRO
DUBBING
14
CXXX
SWXXX
B
DXXX
,
TO E
TUNER C. B
CN5
JWXXX
C
K BATT C. B
SW310
C D
SW309
RADIO /BAND
TO A
CN201
MAIN C. B
6 5
3 1
D565
OPE/ BATT
BLK BLK BLK BLK BLK ORG
CN502
1
6 5
3
CNA551
1
2
5
6
9
10
134
BCE
B C E
D506
D507
D508
25
< HR >
<K, EZ>
24
C511
B C E
LCD501
40
45
35
30
20
15
10
50
55
60
IC501
5
1
64
65
70
75
80
JW47 JW48
E C B
1579111315171921232527293133
3
D
E C B
BLK
E C B
13
10
11
ORG
12569
10
9
6
5
2
1
E C B
B C E
E C B
BCE
BCE B C E
CN501
SW308
TAPE/
DECK1/2
IC571
REMOTE
SENSOR
SW301
POWER
TO A
CN202
MAIN C. B
LCD501
BATTERY
R14
BATTERY
R14
C LED C. B
(DISPLAY)
BLK
ORG
111
FFC4
E
D601~D610
TO H DECK C. B
CON1
(DISPLAY BACK LIGHT)
BATTERY
R14
BATTERY
R14
F
G
H
< K, EZ > : AC230V, 50Hz < HR > : AC
220V-- 240V
I
50/60Hz < K, EZ >
GRN
YEL
2
J
1
< HR >
J701 AC~
110V-- 120V /
YEL
ORG RED
< HR >
SW701
AC VOLTAGE
110V-- 120V
J POWER C. B D SWITCH C. B
SW391
SW392
SW394
SW393
CLOCK
TIMER
ENTER
SLEEP
RED1RED
2
SW381
1
3 4
VOLUME
/ TIMER
YEL BLK BLK BLK
1 2 3
1
344
SW369
T-BASS
SW395
QSURROUND
SW397
3-MODE
EQUALIZER
220V-- 240V
BATTERY
R14
BATTERY
R14
< K, EZ >
YEL
GRN
1
BATTERY
R14
BATTERY
R14
PT701
RED2
RED1
TO A MAIN C. B
CN501
CON501
1
3
BLK YEL RED
< HR >
2
2221
Page 15
SCHEMATIC DIAGRAM-5 (FRONT SECTION)
2423
Page 16
WIRING-5 (CD, CASSETTE MECHA SECTION)
1
234567
8
9
10
11 12 13
14
A
B
C
D
To A MAIN C.B CN802
E
F LOADING MOTOR C.B
SW2
SW1
CON3
42
135
51
FFC3
To A MAIN C.B CN803
SW1
(OPEN)
SW2
(CLOSE)
(LOADING MOTOR)
G CD MOTOR C.B
66
5
4
FFC2
3 1
CON2
2
M3
SW1
1
M1
DECK2
GRN
BLK
BRN
BLK
YEL
YEL
GRN
BLK
EH
WHT
WHT
BLK
GRY
BLK
BLK
RPH
WHT
RED
BLK
GRY
BLK
BLK
WHT
RED
87 5 3 1
CON301
TO A MAIN C. B CN301
BLK
CON302
TO A MAIN C. B CN302
DECK1
RPH
1
3
I RELAY C. B
WHT BLK
PNK
L­L+ R­R+
TO B FRONT C. B
SW4
(CST2)
SW4
111
15911
2610
CN461
FFC4
CON1
IC2
1 3
M2
SPINDLE
MOTOR
M2
SW5
(CAM2)
SW5
SFR1
R1
SOL2
F
M3
(SLED MOTOR)
SW1
INSIDE
LIMIT SW
G
PICK UP ASSY
H
I
CON1
16
FFC1
J
1
To A
MAIN C.B
CN801
H DECK C. B
SW3
(RECA)
SW3
LETTRING
L
M4
DECK
MOTOR
LONG DASH
CROSS MARK
H+
-
M
SOL1
SHORT DASH
SW2
(CAM1)
SW2
SW1
(CST1)
SW1
IC1
1
3
2625
Page 17
IC BLOCK DIAGRAMS
IC, LA6541D IC, BU2092 IC, LC72121M
IC, T A7291S IC, TA2104AN IC, BU4052BC
IC, M62439SP
IC, MM1454XFBE
2827
Page 18
VOLTAGE CHARTS
[IC]
IC001/TA2104AN
Pin No. Voltage (V)
10 2 0.79 30 4 4.57 5 4.76 6 4.22 7 4.57 80
9 0.21 10 3.97 11 1.27 12 1.25 13 3.86 14 4.1 15 0.7 16 1.17 17 1.46 18 4.5 19 3.29 20 4.76 21 3.01 22 4.76 23 3 24 4.75
IC002/LC72121M
Pin No. Voltage (V)
1 1.33
20
30
4 0.01
50
6 4.96
7 0.04
8 0.03
9 3.86 10 4.09 11 0 12 0 13 1.06 14 0 15 0 16 1.34 17 2.74 18 0.98 19 0.98 20 0.74 21 0 22 1.4 23 24
IC201/MM1454XF
Pin No. Voltage (V)
1 3.5 2 3.5 3 0.05 4 0.3 5 3.5 6 3.5 7 3.5 80
9 3.5 10 3.5 11 3.5 12 3.5 13 3.5 14 4.2 15 3.5 16 7.69
IC202/M62439SP
Pin No. Voltage (V)
1 2.85
2 2.85
3 0.04
4 0.04
5 0.04
6 2.85
7 2.85
8 2.88
9 2.85 10 5.7 11 3.36 12 0 13 2.88 14 2.87 15 2.85 16 2.6 17 2.6 18 2.6 19 2.85 20 2.85
IC203/BA5417
Pin No. Voltage (V)
1NC 2 11.1 3 5.97 4 11.9 5 5.95 6 11.1 70 8 3.5
9 6.6 10 0.5 11 0 12 0 13 0.5 14 0 15 0
IC301/NJM4558LD
Pin No. Voltage (V)
1 3.54
2 3.55
3 3.55
40
5 3.55
6 3.55
7 3.54
8 8.48
IC302/NJM4558L-D
Pin No. Voltage (V)
1 3.55
2 3.55
3 3.52
40
5 3.52
6 3.56
7 3.55
8 8.48
IC303/BU4052BC
Pin No. Voltage (V)
1 2.8 2 0.2 3 0.15 40 50 60 70 80
9 5.69 10 0.02 11 0 12 0.56 13 0.3 14 0 15 0.3 16 5.7
IC304/BU2092
Pin No. Voltage (V)
10
2 0.55
30
40
5 0.02
6 0.03
7 8.47
8 0.28
9 0.05 10 5.69 11 0.5 12 0.05 13 0.03 14 0 15 0 16 0 17 0 18 5.7
IC501/LC867132V-5L08
Pin No. Voltage (V)
1 0.81 2 0.02 3 0.01 4 0.82 5 0.01 6 0.02 7 4.63 8 2.23
9 2.64 10 0.01 11 2.28 12 2.46 13 4.83 14 4.98 15 5.01 16 4.55 17 4.98 18 5.01 19 4.97 20 0.63 21 4.97 22 0.01 23 0.01 24 0.01 25 4.83 26 0.46 27 0.03 28 5.23 29 2.46 30 2.45 31 2.44 32 2.41 33 2.46 34 2.43 35 2.44 36 2.42 37 2.44 38 2.44 39 2.43 40 2.41 41 4.82 42 0 43 2.42 44 2.43 45 2.39 46 2.41 47 2.4 48 2.44 49 2.42 50 2.44
Pin No. Voltage (V)
51 2.44 52 2.44 53 2.44 54 2.44 55 2.44 56 2.4 57 2.44 58 2.41 59 2.44 60 2.4 61 4.98 62 2.2 63 4.98 64 2.47 65 2.49 66 2.46 67 4.94 68 0 69 4.83 70 0.01 71 0.01 72 0.01 73 4.79 74 4.7 75 0.01 76 0.01 77 0.01 78 0.01 79 0.04 80 0.01
IC801/LA9241ML
Pin No. Voltage (V)
1 2.47 2 2.47 3 2.5 4 2.5 5 2.48 6 2.49 7 2.49 8 2.49
9 2.49 10 2.47 11 2.5 12 2.49 13 2.49 14 2.5 15 2.48 16 2.5 17 2.5 18 2.49 19 2.47 20 2.49 21 2.49 22 0.006 23 2.48 24 2.49 25 2.5 26 2.5 27 2.49 28 2.49 29 2.5 30 2.4 31 2.39 32 0.1 33 0.1 34 4.89 35 4.75 36 0.05 37 0.04 38 4.87 39 0.06 40 0.05 41 1.58 42 2.39 43 2.51 44 2.48 45 0.01 46 2.49 47 2.49 48 NC 49 0.01 50 2.42
Pin No. Voltage (V)
51 4.7 52 4.7 53 0.003 54 0.03 55 0.1 56 4.9 57 2.49 58 2.5 59 0.95 60 0.96 61 2.21 62 4.47 63 1.04 64 5.03
3029
Page 19
IC802/LC78622ED
Q001 2.19 4.04 2.93 Q071 0 0.01 0.64 Q072 0 3.46 0 Q151 2.64 4.84 3.34 Q152 3.44 4.84 2.42 Q201 1.22 3.12 1.85 Q202 1.23 1.65 1.85 Q291 0 0 0.64 Q292 0 0 0.64 Q301 3.55 3.55 0.06 Q302 3.55 3.55 0.06 Q303 3.55 3.55 0.06 Q331 0 0.23 0.22 Q332 0 0.24 0.23 Q341 0.1 3.55 3.12 Q342 0.1 3.55 3.13 Q344 0 3.15 0.05 Q351 3.55 3.54 8.46 Q352 3.55 3.54 8.46 Q451 15.76 0 15.73 Q452 0 15.72 0 Q453 15.76 0.61 15.75 Q454 0 15.73 0 Q461 15.73 0 15.72 Q521 0 0.02 1.56 Q521 11.89 11.19 11.2 Q522 11.2 11.2 10.53 Q523 0 0 4.53 Q524 0 7.63 0 Q525 6.9 10.4 7.52 Q526 7.63 5.6 6.89 Q527 5 6.89 5.57 Q536 10.98 11.26 10.27 Q541 7.63 1 7.01 Q542 0.71 7 0 Q561 0.01 0.11 0.69 Q571 0 0.01 12 Q601 0.01 0.17 12.55 Q801 4.94 1.6 4.29 Q802 2.45 2.45 0.01 Q871 7.59 5.11 6.87 Q882 4.81 4.8 0 Q884 0 0 4.8 Q891 7.61 7.59 6.86 Q892 0 0.15 4.51
Pin No. E(V) C(V) B(V)
[TRANSISTOR]
Pin No. Voltage (V)
1 0.01 2 0.01 3 0.02 4 0.01 5 1.93 6 4.9 7 0.08 8 0.01
9 2.48 10 2.51 11 0.01 12 0.05 13 0.06 14 4.88 15 0.02 16 0.06 17 4.88 18 4.88 19 0.1 20 0.1 21 0.1 22 NC 23 4.91 24 0.13 25 0.13 26 NC 27 4.88 28 NC 29 NC 30 NC 31 2.35 32 0.007 33 0.007 34 NC 35 NC 36 4.88 37 2.12 38 0.001 39 0.001 40 0.002 41 4.88 42 NC 43 4.91 44 2.14 45 2.04 46 0.007 47 NC 48 NC 49 NC 50 NC
IC804/LA6541D
Pin No. Voltage (V)
51 0.004 52 2.47 53 0.02 54 0.003 55 0.02 56 4.7 57 4.7 58 4.88 59 NC 60 NC 61 2.35 62 0 63 0 64 0
Pin No. Voltage (V)
1 7.52 2 4.97 3 2.46 4 2.46 5 3.38 6 3.36 70 80
90 10 3.37 11 3.37 12 2.46 13 2.45 14 4.97 15 6.85 16 4.95 17 4.87 18 2.45 19 2.46 20 3.36 21 3.39 22 0 23 0 24 0 25 3.38 26 3.38 27 2.46 28 2.45 29 2.46 30 7.52
31
Page 20
IC DESCRIPTION IC, LA9241ML
Pin No. Pin Name I/O Description
1
FIN2
Pin to which external pickup photo diode is connected. RF signal is created by adding
I
with the FIN1 pin signal. FE signal is created by subtracting from the FIN1 pin signal.
10 11
12
13 14 15 16
2
3
4 5 6 7
8
9
FIN1
E
F
TB
TE–
TE
TESI
SCI
TH TA
TD–
TD
JP TO FD
I
Pin to which external pickup photo diode is connected. Pin to which external pickup photo diode is connected. TE signal is created by
I
subtracting from the F pin signal.
I
Pin to which external pickup photo diode is connected.
I
DC component of the TE signal is input.
I
Pin to which external resistor setting the TE signal gain is connected between the TE pin.
O
TE signal output pin. TES “Track Error Sense” comparator input pin. TE signal is passed through a band-
I
pass filter then input.
I
Shock detection signal input pin.
I
Tracking gain time constant setting pin.
O
TA amplifier output pin. Pin to which external tracking phase compensation constants are connected between
I
the TD and VR pins.
I
Tracking phase compensation setting pin.
I
Tracking jump signal (kick pulse) amplitude setting pin.
O
Tracking control signal output pin.
O
Focusing control signal output pin.
17
18
19
20 21 22 23 24 25
26
27 28 29
30, 31
FD–
FA
FA–
FE
FE–
AGND
NC
SP
SPG
SP–
SPD
SLEQ
SLD
SL–, SL+
— —
Pin to which external focusing phase compensation constants are connected between
I
the FD and FA pins. Pin to which external focusing phase compensation constants are connected between
I
the FD– and FA– pins. Pin to which external focusing phase compensation constants are connected between
I
the FA and FE pins.
O
FE signal output pin.
I
Pin to which external FE signal gain setting resistor is connected between the FE pin. Analog signal GND. No connection.
O
Single ended output of the CV+ and CV– pin input signal.
I
Pin to which external spindle gain setting resistor in 12 cm mode is connected. Pin to which external spindle phase compensation constants are connected together
I
with SPD pin.
O
Spindle control signal output pin.
I
Pin to which external sled phase compensation constants are connected.
O
Sled control signal output pin.
I
Sled advance signal input pin from microprocessor.
32, 33
34 35
JP–, JP+
TGL
TOFF
I
Tracking jump signal input pin from DSP.
I
Tracking gain control signal input from DSP. Low gain when TGL = H.
I
Tracking off control signal input pin from DSP. Off when TOFF = H.
32
Page 21
Pin No. Pin Name I/O Description
36
TES
O
Pin from which TES signal is output to DSP.
37
38
39, 40
41
42
43
44 45 46 47 48 49 50 51 52
HFL
SLOF
CV–, CV+
RFSM
RFS–
SLC
SLI
DGND
FSC TBC
NC DEF CLK
CL DAT
—
—
“High Frequency Level” is used to judge whether the main beam position is on top of
O
bit or on top of mirror.
I
Sled servo off control input pin.
I
CLV error signal input pin from DSP.
O
RF output pin. RF gain setting and EFM signal 3T compensation constant setting pin together with
I
RFSM pin. “Slice Level Control” is the output pin which controls the RF signal data slice level by
O
DSP.
I
Input pin which control the data slice level by the DSP. Digital system GND.
O
Output pin to which external focus search smoothing capacitor is connected.
I
“Tracking Balance Control” EF balance variable range setting pin. No connection.
O
Disc defect detector output pin.
I
Reference clock input pin. 4.23 MHz of the DSP is input.
I
Microprocessor command clock input pin.
I
Microprocessor command data input pin. 53 54 55 56 57 58 59 60 61 62 63 64
CE
DRF
FSS
VCC2
REFI
VR
LF2 PH1 BH1
LDD
LDS
VCC1
— —
—
I
Microprocessor command chip enable input pin.
O
“Detect RF” RF level detector output.
I
“Focus Search Select” focus search mode (± search/+ search) select pin. Servo system and digital system Vcc pin. Pin to which external bypass capacitor for reference voltage is connected.
O
Reference voltage output pin.
I
Disc defect detector time constant setting pin.
I
Pin to which external capacitor for RF signal peak holding is connected.
I
Pin to which external capacitor for RF signal bottom holding is connected.
O
APC circuit output pin.
I
APC circuit input pin. RF system Vcc pin.
33
Page 22
IC, LC78622ED
Pin No. Pin Name I/O Description
1
DEFI
I
Defect sense signal (DEF) input pin. (Connect to 0V when not used). 2 3 4 5 6 7 8 9
10 11
12, 13
14
15 16 17 18
TAI
PDO
VVSS
ISET
VVDD
FR
VSS
EFMO
EFMIN
TEST2
CLV+, CLK–
___
V/P
HFL
TES
TOFF
TGL
—
—
—
I
O
For PLL.
I
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Phase comparator output pin to control external VCO. GND pin for built-in VCO. Be sure to connect to 0V. Pin to which external resistor adjusting the PD0 output current. Power supply pin for built-in VCO.
I
Pin for VCO frequency range adjustment.
Digital system GND. Be sure to connect to 0V.
O
For slice level control.
I I
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
O
Disc motor control output. Three level output is possible using command.
Rough servo or phase control automatic selection monitoring output pin. Rough servo
O
EFM signal output pin. EFM signal input pin.
at H. Phase servo at L.
I
Track detect signal input pin. Schmidt input.
I
Tracking error signal input pin. Schmidt input.
O
Tracking OFF output pin.
O
Tracking gain selection output pin. Gain boost at L.
19, 20
21
22
23
24-28
29 30 31
32, 33
34 35 36 37
JP+, JP–
PCK
FSEQ
VDD
CONT1-CONT5
EMPH
C2F
DOUT
TEST3, TEST4
N.C.
MUTEL
LVDD
LCHO
O O
O
—
I/O
O O O
—
O
—
O
Track jump control signal output pin. Three level output is possible using command.
EFM data playback clock monitoring pin 4.3218 MHz when phase is locked in.
Sync signal detection output pin. H when the sync signal which is detected from EFM
signal and thesync signal which is internally generated agree.
Digital system power supply pin.
The pin is controlled by the serial data command from microprocessor. When
General purpose input/output pin 1 to 5.
the pin is not used, set the pin to the input terminal and connect to 0V, or alternately set the pin to output terminal and leave
the pin open. De-emphasis monitor output pin. De-emphasis disc is being played back at H. C2 flag output pin. DIGITAL OUT output pin. (EIAJ format).
I
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Not used. Set the pin to open.
L-channel mute output pin.
L-channel 1-bit DAC.
L-channel power supply pin.
L-channel output pin. 38 39 40 41 42
LVSS
RVSS RCHO RVDD
MUTER
— —
—
O
R-channel 1-bit DAC.
O
L-channel GND. Be sure to connect to 0V. R-channel GND. Be sure to connect to 0V. R-channel output pin. R-channel power supply pin. R-channel mute output pin.
34
Page 23
Pin No. Pin Name I/O Description
43
XVDD
—
Crystal oscillator power supply pin. 44 45 46 47 48 49 50
51
52
53 54 55 56 57 58 59
XOUT
XIN XVSS SBSY EFLG
PW
SFSY
SBCK
FSX
WRQ RWC
SQOUT
COIN
___________
CQCK
________
RES
TST11
—
O
Pin to which external 16.9344 MHz crystal oscillator is connected.
I
Crystal oscillator GND pin. Be sure to connect to 0V.
O
Subcode block sync signal output pin.
O
C1, C2, single and dual correction monitoring pin.
O
Subcode P, Q, R, S, T, U and W output pin.
O
Subcode frame sync signal output pin. Falls down when subcode enters standby. Subcode read clock input pin. Schmidt input. (Be sure to connected to 0V when not
I
in use.) Pin outputting the 7.35 kHz sync signal which is generated by dividing frequency of
O
crystal oscillator.
O
Subcode Q output standby output pin.
I
Read/write control input pin. Schmidt input.
O
Subcode Q output pin.
I
Command input pin from microprocessor.
I
Command input read clock or subcode read input clock from SQOUT pin
I
LC78622 reset input pin. Set this pin to L once when the main power is turned on.
O
Test signal output pin. Use this pin as open (normally L output). 60 61 62
63
64
16M
4.2M
TEST5
______
CS
TEST1
O
16.9344 MHz output pin.
O
4.2336 MHz output pin.
I
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
Chip select signal input pin with built-in pull-down resistor. Be sure to connect to 0V
I
while it is not controlling.
Test signal input pin without built-in pull-down resistor. Be sure to connect to 0V.
I
35
Page 24
IC, LC867132V-5L08
Pin No. Pin Name I/O Description
O
1 2 3 4 5 6 7 8 9
O-RWC/CE
O-DATA
O-CLK
_______
O-STB
O-CKSFT
I-HOLD
_______
I-RST
XT1 XT2
CD read/write control output and TU ship enable.
O
Data output for IC BU2092, LC72131D (Z) and M62439SP.
O
Clock output for IC BU2092 and LC72131.
O
Strobe output for IC BU2092.
O
Clock shift output for system micro computer.
I
Detect hold status.“H” = HOLD.
I
Reset micro computer.
I
Connected to crystal oscillator (32,768kHz).
O 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
VSSI
CF1 CF2
VDD1
I-DSW I-KEYO I-CDSW
I-ENC I-KEY1 I-CST1
I-STIND I-TUDO
O-CDOPEN
O-CDCLOSE
O-CDMUTE
________
O-INIT
I-DRF
─
─
Connected to digital ground.
I
Connected to 6MHz oscillator.
O
Power supply to micro computer (+5V).
I
Deck mechanism status detection input (AD).
I
Key AD value input.
I
CD tray OPEN/CLOSE status detection input (AD).
I
AD value input for rotary encoder output A and B.
I
Key AD value input.
I
Deck 1 tape detection.
I
TUNER STEREO indicator input.
I
Data input from IC LC72131D (Z).
O
CD tray open control output.
O
CD tray close control output.
O
CD mute output . (Not connected)
O
Initial diode matrix detection output.
I
CD (detect RF ) RF level detection input. 27 28
29 〜40
41 42
43 〜60
61 62 63
64 〜66
67 68 69 70 71
I-WRQ
I-RMT
SO 〜SI1
VDD3
VSS3
S12〜S13, S16〜S31
I-CAM1
I-AS1
I-CAM2
COM0 〜COM2
I-AS2
VSS2 VDD2 O-PL2
O-MOT
─ ─
─ ─
I
CD sub code Q stand-by input.
I
Remote controller input.
O
LCD segment output. Power supply to micro computer (+5V). Connected to digital ground.
O
LCD segment output.
I
Deck 1 mechanism status detection input.
I
Deck 1 mechanism status detection input.
I
Deck 2 mechanism status detection input. (stop pulse)
O
LCD common output.
I
Deck 1 mechanism status detection input. (auto pulse) Connected to digital ground. Power supply to micro computer (+5V).
O
Single & deck 2 plunger control output.
O
Deck mechanism motor control output.
36
Page 25
Pin No. Pin Name I/O Description
72
O-PL1
Double deck 1 plunger control output. (Not connected).
O 73 74
75 〜77
78 79 80
O-P. CONT
O-MUTE
─
O-COIN
I-SQOUT
─
Power supply control output.
O
Main mute output.
O
Not connected. CD command output.
O
CD sub code Q input.
I
Clock output for CD command and sub code.
O
37
Page 26
ELECTRICAL ADJUSTMENT <HR Model>
E TUNER C.B
L003
AM BAR ANTENNA
L002
3
L005
IC001
1
L007
L006
IC002
TC001
5 4
L004
2
TP1 (VT)
DECK1 : PLAY HEAD DECK2 : R/P/E HEAD
6
REV
DECK 1 DECK1,2
<TUNER SECTION>
1. AM IF Adjustment
L007 ....................................................................... 603kHz
Adjust the level at 603 kHz to MAX by L007
2. MW VT Adjustment Setting : • Test point : TP1 (VT)
• Adjustment location : L004
Method : Set to MW 1602 kHz and adjust L004 so that the
test point becomes 5.6 V ± 0.05 V.
3. MW Tracking Adjustment
L003 ...................................................................... 603 kHz
TC001 ...................................................................1404 kHz
6
FWD
5. FM Tracking Adjustment
L005 .................................................................. 108.0 MHz
<DECK SECTION>
6. Head Azimuth Adjustment Setting : • Test point : TTA320
• Adjustment location : Head Azimuth Adjustment Screw
Method : Play back the 10kHz signal od test tape and adjust
Screw so that the output becomes maximum. Next perform REV PLAY mode.
4. FM VT Adjustment Setting : • Test point : TP1 (VT)
• Adjustment location : L006
Method : Set to FM 108.0 MHz and adjust L006 so that the
test point becomes 6.0 V ± 0.05 V.
38
Page 27
ELECTRICAL ADJUSTMENT <K, EZ Model>
E TUNER C.B
(MW)
L003 MW/LW BAR ANTENNA
(LW)
<DECK SECTION>
8. Head Azimuth Adjustment Setting : • Test tape : TTA-320
• Test point : J201 (Phones jack)
• Adjustment location : Head Azimuth Adjustment Screw
Method : Play back the 10kHz signal of test tape and adjust
screw so that the output becomes maximum. Next perform REV PLAY mode.
3
1
DECK1 : PLAY HEAD DECK2 : R/P/E HEAD
6
REV
DECK 1 DECK1,2
<TUNER SECTION>
1. AM IF Adjustment
L007 ....................................................................... 603kHz
Adjust the level at 603 kHz to MAX. by L007
2. MW VT Adjustment Setting : • Test point : TP1 (VT)
• Adjustment location : L004
Method : Set to MW 1611 kHz and adjust L004 so that the
test point becomes 5.6 V ± 0.05 V.
3. MW Tracking Adjustment
L003 (M W )............................................................ 603 kHz
TC001 ...................................................................1404 kHz
4. LW VT Adjustment Setting : • Test point : TP1 (VT)
• Adjustment location : L051
Method : Set to LW 288 kHz and adjust L051 so that the
test point becomes 4.5 V ± 0.05 V.
FWD
5
7
L002
IC001
L005
TC051
TC001
6
L007
L006
IC002
L004
2
L051
4
TP1 (VT)
JW005
PRACTICAL SERVICE FIGURE
<TUNER SECTION>
<FM SECTION>
IHF Sensitivity : Less than 14 dB (THD 3%) [at 87.5/98.0 MHz]
Less than 15dB
6
[at 108.0 MHz] Signal to noise ratio : More than 60 dB (Input - 54 dB) [at 98.0 MHz] Distortion : Less than 2.0% (Input - 54dB) [at 98.0 MHz] Stereo separation : More than 25 dB
[at 98.0 MHz] Intermediate frequency : 10.7 MHz
5. LW T racking Adjustment
L003 (L W) ............................................................ 153 MHz
TC051 .................................................................... 288 kHz
<AM (MW) SECTION>
Sensitivity : Less than 52 dB (S/N 10 dB) [at 603 kHz]
6. FM VT Adjustment Setting : • Test point : TP1 (VT)
• Adjustment location : L006
Method : Set to FM 108.0 MHz and adjust L006 so that the test
point becomes 6.0 V ± 0.05 V.
Signal to noise ratio : More than 35 dB (Input - 74 dB9 [at 999 kHz] Distortion Less than 2.0%
Less than 51 dB [at 999/1404 kHz]
(Input - 74 dB) [at 999 kHz]
7. FM Tracking Adjustment
Intermediate frequency : 450 kHz
L005 .................................................................. 108.0 MHz
<LW SECTION> <EZ, K Model>
Sensitivity : Less than 57 dB
[at 153 kHz] Less than 56 dB [at 198/288 kHz]
Signal to noise ratio : More than 35 dB
[at 198 kHz]
<DECK SECTION>
T ape speed : 3000 Hz ± 90 Hz W ow & flutter : Less than 0.35%
(JIS RMS)
T ake-up torque : 30 ~ 60 g-cm
(FWD, PLAY) F.F & REW torque : 55 ~ 150 g-cm Back tension : 1 ~ 7 g-cm
(FWD, REV) S/N ratio : More than 38 dB
(PB, AC, DC Vol.21)
More than 36 dB
(R/PB, SP OUT, AC) Distortion : Less than 3.0%
(PB, DC)
Less than 5.0%
(R/PB, DC) Noise level Less than 35 mV
(PB, AC, DC)
Less than 55mV
(R/PB, AC) Erasing ratio More than 40 dB
(w/o Filtor)
4039
Page 28
MECHANICAL EXPLODED VIEW 1/1
34
30
25
23
24
27
32
31
33
17
A
48
46
47
50
G
B
59
A
C
A
49
B
A
35
36
38
B
28
I
29
I
26
24
23
17
C
C
29
22
37
28
LED C.B
FRONT C.B
21
CHASS MECHA
39
C
C
43
C
C
B
41
40
F
C
42
BATT C.B
44
D
45
51
C
20
CHAS CENTER
18
17
C
17
I
C
C
C
17
16
15
14
9
8
1
13
4
3
5
LCD DISPLAY C
10
7
C
6
SH.DISPLAY
52
G
E
E
11
19
CC
CD MECHA
C
G
17
C
16
I
POWER C.B
MAIN C.B
53
TUNER C.B
I
TU.CHASS
54
57
58
C
55
56
SWITCH C .B
BAR ANT
2
12
4241
Page 29
MECHANICAL PARTS LIST 1/1
REF. NO PART NO. KANRI DESCRIPTION
1 8Z-CH1-038-010 NET,SPKR ASS’Y 2 8Z-CH1-014-010 PANEL,CD 3 8Z-CH1-015-010 WINDOW,DISPLAY 4 8Z-CH1-044-010 PLATE,DISPLAY EX 5 8Z-CH1-041-010 PANEL,FR EX
6 8Z-CH1-210-010 BTN,FUNC BASE R 7 8Z-CH1-017-010 BTN,FUNC 8 8Z-CH1-024-010 BTN,POWER 9 8Z-CH1-202-010 BTN,FUNC BASE L 10 8Z-CH1-019-010 BTN,CONTROL
11 86-CT9-223-010 CUSH,FOOT 12 8Z-CH1-026-010 PIPE,SPKR R 13 86-CT9-040-010 BADGE,AIWA ­ 14 8Z-CH1-025-010 PIPE,SPKR L 15 8Z-CH1-001-010 CABI,FR
16 88-CD5-603-010 SPKR,10 7OHM 17 88-CD5-211-010 HLDR,SPKR 18 88-905-141-210 FF-CABLE, 5P 1.25 19 88-906-181-110 FF-CABLE,6P 1.25 20 88-CD5-638-010 FF-CABLE, 16P 1.0 220MM
21 8Z-CH1-203-010 HLDR,DISPLAY 22 8Z-CH1-205-010 HLDR,LOCK 2N R 23 88-CD5-213-010 SPR-C,LOCK 24 82-NF5-229-010 PLATE,LOCK 25 8Z-CH1-204-010 HLDR,LOCK 2N L
26 8Z-CH1-209-010 SPR-P,CASS R 27 8Z-CH1-208-010 SPR-P,CASS L 28 86-CT9-220-110 OIL-DMPR,BRACKET 29 86-CT9-225-010 OIL-DMPR,GEAR N 30 8Z-CH1-003-010 BOX,CASS L
31 88-CD4-209-010 SPR-T,CASS A 32 8Z-CH1-009-010 CHAS,CASS 33 8Z-CH1-005-010 LID,CASS L 34 8Z-CH1-007-010 WINDOW,CASS L 35 8Z-CH1-008-010 WINDOW,CASS R
NO.
REF. NO PART NO. KANRI DESCRIPTION
36 8Z-CH1-006-010 LID,CASS R 37 8Z-CH1-004-010 BOX,CASS R 38 88-CD4-214-010 SPR-T,CASS B 39 88-911-101-110 FF-CABLE,11P 1.25 40 87-A90-086-010 COVER,AC-SOCKET
! 41 87-A60-178-010 JACK,AC E W/SW ! 42 87-A91-302-010 SW,AC SL 2 2 2 SDKGA40100<HRJ<S>>
43 88-CD5-212-010 HLDR,TRANS
! 44 88-CD5-647-010 PT,E<K<S>,EZ<S>> ! 44 88-CD5-648-010 PT,H<HRJ<S>>
45 8Z-CH1-002-010 CABI,REAR 46 8Z-CH1-012-010 HANDL,ARM 47 8Z-CH1-013-010 HANDL,GRIP 48 86-CT4-616-010 ANT,ROD 49 88-CD5-206-010 SPR-C,BATT LINK
50 8Z-CH1-016-010 LID,BATT 51 88-CD5-207-010 SPR-C,BATT ­ 52 88-CD4-204-010 HLDR,JOINT 53 8Z-CH1-212-010 HLDR,ANT 2 54 8Z-CH1-021-010 KNOB,RTRY VOL
55 8Z-CH1-042-010 CABI,TOP EX 56 8Z-CH1-018-010 BTN,TIMER 57 8Z-CH1-020-010 BTN,EQ 58 8Z-CH1-201-010 BTN,EQ BASE 59 88-CD5-040-010 PLATE,COVER
A 87-751-104-410 VT2+3-30 B 87-B10-166-010 VT2+3-16 W/O C 87-261-097-410 V+3-12 D 87-501-095-410 VF+3-8 E 87-721-095-410 QT2+3-8GLD W/O SLOT
F 87-352-075-210 VT2+2.6-10 G 87-721-096-410 QT2+3-10 GLD H 87-751-097-410 SCREW 3X12 I 87-751-095-410 VT2+3-8 W/O
NO.
43
Page 30
TAPE MECHANISM PARTS LIST 1/1
REF. NO PART NO. KANRI DESCRIPTION
1 86-ZM3-215-010 CHAS ASSY,RS 2 86-ZM3-202-010 BASE,HEAD S 3 86-ZM3-205-010 SPR-C,RPH S 4 82-ZM1-333-210 PLATE,LINK 2 5 86-ZM3-206-010 SPR-C,EH S
6 87-A90-403-019 HEAD,RPH MS15R 7 86-ZM3-201-010 CHAS,HEAD S(DECK L) 7 82-ZM3-206-910 CHAS,HEAD(DECK R) 8 87-045-347-019 MOT,SHU2L 70(M1) 9 82-ZM1-269-219 SPR-T,BRG
10 82-ZM1-219-110 SPR-T,LINK 11 86-ZM3-209-010 S-SCREW,ASIMUTHS 12 86-ZM3-207-010 S-SCREW,RPH 13 87-A90-404-019 HEAD,EH LE15B 14 86-ZM3-208-010 S-SCREW,EH
15 86-ZM3-203-010 HLDR,MOTS 16 82-ZM1-245-210 HLDR,IC 17 82-ZM1-218-019 SPR-E,HB 18 86-ZM3-214-010 BELT,SUB RR 19 82-ZM1-222-219 LVR,PLAY
20 82-ZM1-217-419 REEL TABLE 21 82-ZM1-244-519 SPR-C,BT 22 82-ZM1-285-410 SPR-C,BT L 23 82-ZM1-257-019 SPR-T,CAS 24 82-ZM3-221-010 PULLEY,MOT 2M
25 82-ZM1-242-019 LVR,CAS 26 82-ZM1-243-019 LVR,STOP 27 82-ZM1-344-119 LVR ASSY,PINCH 28 86-ZM3-204-010 SPR-T,PINCHDS 29 82-ZM1-240-119 LVR,REC (DECK 2)
30 86-ZM3-210-010 BELT,RS 32 82-ZM3-305-119 GEAR,CAM M2 33 82-ZM1-227-319 LVR,TRIG 34 82-ZM3-306-110 LVR,FR M2 35 82-ZM1-265-119 SPR-E,TRIG
36 87-761-073-419 VFT2+2.6-6 W/O SLOT 37 82-ZM1-239-019 CAPSTAN N 2.2-41.7 38 82-ZM1-322-019 SPR-T,FR60 39 82-ZM1-220-219 GEAR,IDLER 40 82-ZM3-616-019 RING MAGNET 4
NO.
REF. NO PART NO. KANRI DESCRIPTION
41 82-ZM1-216-319 GEAR,REEL 42 86-ZM3-213-010 S-SCREW,HLDR,MOT 3 43 82-ZM1-225-219 GEAR,FR 44 82-ZM1-226-019 GEAR,REW 45 82-ZM3-333-310 SLIP DISK ASSY 2
46 82-ZM1-338-010 BELT FR4 47 82-ZM1-349-019 FLY-WHL RW (DECK L) 47 82-ZM3-338-010 FLY-WHL R3W (DECK R) 48 82-ZM1-259-210 SPR-T,PINCH R 49 82-ZM1-341-110 LVR ASSY,PINCH L2
50 82-ZM1-258-210 SPR-T,PINCH L 51 82-ZM1-314-110 PLATE,HEAD 52 82-ZM1-208-310 HLDR,HEAD 53 87-A90-366-010 HEAD,PH YK50P-BF414 54 82-ZM1-207-810 GUIDE TAPE
55 82-ZM1-213-010 SPR-T,HEAD 56 82-ZM1-210-110 GEAR,HT 57 86-ZM4-206-010 S-SCREW AZIMUTH L 58 82-ZM1-348-010 FLY-WHL,LW 59 82-ZM1-236-019 CAPSTAN N 2-41.5
60 82-ZM3-335-210 PULLEY,COUPLER M3 61 86-ZM1-206-010 BELT,MAIN L 62 82-ZM1-266-110 LVR,DIR 63 82-ZM1-214-010 SPR-T,DIR 64 82-ZM1-255-310 SPR-E,LVR DIR
65 82-ZM3-339-010 SHAFT,COUPLER N3 A 87-251-071-417 U+2.6-4 B 80-ZM6-243-019 SH,1.75-3.6-0.5 SLT C 82-ZM3-334-010 PW,2.16-6-0.4 D 80-ZM6-207-010 V+1.6-7
E 85-ZM3-202-010 S-SCREW TG F 82-ZM1-288-010 SH,1.63-3.2-0.5 SLT G 87-B10-043-010 W-P,0.99-4-0.25 SLT H 87-571-032-410 VIT+2-3
NO.
44
Page 31
TAPE MECHANISM EXPLODED VIEW 1/1
55
HEAD C.B
56
49
62
50
57
D
51
E
52
54
63
27
65
D
53
10
14
5
13
(DECK L only)
2
12
11
12
3
6
17
9
7
(DECK L SIDE)
18
LEVER
19
A
20
4
EJECT R
47
37
8
SOL 2
15
16
SOL 1
A
A
A
24
D
(DECK R SIDE)
30
H
PLATE SHLD M3
44
41
43
35
C
33
34
DECK C.B
16
61
41
45
G
60
E
LEVER EJECT L
1
48
22
29
(DECK 2)
32
64
F
58
D
A
C
B
F
B
42
F
40
39
59
38
B
E
46
21
C
25
27
23
A
26
28
36
4645
Page 32
CD MECHANISM EXPLODED VIEW 1/2
CD MECHANISM PARTS LIST 1/2
13
C
16
17
CUSH-G,
17
MAIN A
C
CUSH-G, MAIN A
3ZG2
14
A
REF. NO PART NO. KANRI DESCRIPTION
NO.
1 83-ZG3-224-310 HLDR,M2 2 83-ZG3-228-610 CHAS,L6 3 83-ZG3-208-010 PULLEY,MOTOR 4 83-ZG3-213-010 LVR,SW 5 83-ZG3-209-610 CAM,SLIDE
6 83-ZG3-207-010 GEAR,TRAY 7 83-ZG3-204-210 GEAR,C 8 83-ZG3-205-010 GEAR,D 9 83-ZG3-217-010 S-SCREW,GEAR D 10 83-ZG3-220-210 GEAR,PULLEY 2
11 83-ZG3-214-010 BELT,L 12 83-ZG3-229-410 TRAY,CD 2 13 83-ZG3-210-110 HLDR,CHUCK 14 83-ZG3-602-010 RING,MAG 15 83-ZG3-212-010 CAP,DISC
REF. NO PART NO. KANRI DESCRIPTION
NO.
16 83-ZG3-211-010 PLATE,DISC 17 81-ZG1-254-010 S-SCEW,MECH HLDR A 87-067-945-110 VFT2+3-12(F10) B 87-251-071-110 U+2.6-4 C 87-512-074-210 VFT2+2.6-8
D 87-352-075-210 VT2+2.6-10
B
15
11
9
10
7
5
8
4
B
C
6
12
D
LOADING
MOTOR-2 C.B
MOTOR C.B
A
C
2
D
3
A
M1
B
1
4847
Page 33
CD MECHANISM EXPLODED VIEW 2/2
12
8
A
A
11
2
6
A
A
1
5
3
4
M3
M2
P.C.B
CD MOTOR C.B
CD MECHANISM PARTS LIST 2/2
REF. NO PART NO. KANRI DESCRIPTION
NO.
1 83-ZG2-243-210 CHAS ASSY,SHT 2 83-ZG2-235-010 GEAR,A3 3 83-ZG2-205-210 GEAR,B 4 83-ZG2-236-010 GEAR MOTOR 3 5 83-ZG2-253-010 SHAFT,SLIDE 5
6 87-A90-836-010 PICKUP,KSS-213F 8 83-ZG2-227-210 TURN TABLE,C1 11 83-ZG2-245-410 LEVER,SHUTTER 12 83-ZG2-250-110 SPR-E,SHT 2 A 87-261-032-210 SCREW V+2-3
49
Page 34
2–1 1, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 311 1
931196
Printed in Singapore
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use