AirLive Ether-GSH2416W User Manual
Ether-GSH2416W
Pure Gigabit Web Managed Switch
User’s Manual
1
TABLE OF CONTENT
1 Introduction................................................................................................................................. 4
1.1 Start to Manage This Switch...................................................................................... 6
1.2 Configuration Functions for the Switch ................................................................... 7
2 Configurations............................................................................................................................. 8
2.1 Port Status ................................................................................................................... 8
2.2 Port Configuration...................................................................................................... 9
2.3 Port Statistics..............................................................................................................11
2.4 VLAN ......................................................................................................................... 13
2.4.1 Port-based VLAN Configuration .................................................................... 14
2.4.1.1 Add Port-Based VLAN Groups................................................................ 15
2.4.1.2 Delete Port-Based VLAN Groups............................................................. 17
2.4.1.3 Edit Port-Based VLAN Groups................................................................ 18
2.4.2 802.1Q VLAN Configuration ........................................................................... 19
2.4.2.1 802.1Q VLAN Port Configuration ........................................................... 20
2.4.2.2 802.1Q VLAN Configuration .................................................................... 21
2.5 Trunk.......................................................................................................................... 24
2.5.1 Trunking Rules.................................................................................................. 25
2.5.2 Get/Refresh the Latest Trunk Settings............................................................ 27
2.5.3 Enable Trunk..................................................................................................... 28
2.5.4 Modify Trunk Settings...................................................................................... 29
2.5.5 Disable Trunk .................................................................................................... 30
2.6 Port Mirroring .......................................................................................................... 31
2.6.1 Get/Refresh the Latest Mirror Settings .......................................................... 32
2.6.2 Enable Mirror ................................................................................................... 33
2.6.3
Modify Mirror Settings .................................................................................... 34
2.6.4 Disable Mirror................................................................................................... 35
2.7 QOS (Quality of Service).......................................................................................... 36
2.7.1 Get/Refresh the Latest QOS Settings.............................................................. 37
2.7.2 Enable QOS ....................................................................................................... 38
2.7.3 Modify QOS Settings ........................................................................................ 39
2.8 Rate and Storm Control ........................................................................................... 40
2.8.1 Rate Control ...................................................................................................... 40
2.8.2 Storm Control.................................................................................................... 42
2.9 System Setup.............................................................................................................. 45
2.9.1 Firmware Update.............................................................................................. 46
2.9.1.1 Firmware Update Via TFTP ..................................................................... 47
2.9.1.2 Firmware Update Via BOOTP/TFTP...................................................... 48
2.9.2 DHCP Client...................................................................................................... 49
2.9.2.1 Assign a fixed IP address........................................................................... 49
2.9.2.2 Assign a IP address by DHCP server ....................................................... 49
2
2.9.3 ARL Aging ......................................................................................................... 50
2.10 User Management ..................................................................................................... 51
2.11 Backup / Restore ....................................................................................................... 52
2.12 Reboot / Reset System............................................................................................... 53
2.13 Command Line Interface (CLI) .............................................................................. 54
2.13.1 Hyper Terminal Setup Options........................................................................ 54
2.13.2 Switch Management Commands In Console.................................................. 54
3 Specifications............................................................................................................................. 60
3
1 Introduction
The Ether-2416W web smart switch is a high performance web-smart Layer 2 switch that provides
users with switched 16 mini-GBIC fiber ports and 8 10/100/1000Mbps copper ports for building up
Ethernet network. This is specially designed for the use at the environment that needs high-density
fiber ports and copper gigabit ports simultaneously, such as big enterprise, big ISP and telephone
companies. When user adopts proper fiber transceivers, single-mode or multi-mode, he may
contracture a high speed backbone for large traffic data center or service center.
Web interface management provides control capability over TCP/IP, this make user convenient and
easy to manage switch with browser no matter at local or remote side.
Non-blocking and maximum wire speed performance are designed on all switched ports, and it also
supports auto-negotiation and MDI/-MDIX function on all switched 8 10/100/1000M RJ-45 Gigabit
ports, these function make user really easy to use and reduce the matching effort on straight and
cross-over line issues and on different speed setting.
This system supports both port-based VLAN and 802.1Q (tag-based) VLAN to catch-up the
application needed incoming VLAN age. To increase bandwidth application, it supports 4 trunk
groups with up to 8 member ports, and moreover, these trunk ports are with fair-over function to
provide redundant back-up when one or some ports are malfunctioned in that trunk group. In
addition to in-band management through RJ-45 ports, it also provides RS-232 terminal port with
command line interface (CLI) for user to do initial setting or operation while in-band domain is
malfunctioned.
4
Main Features
Broadcom® chipset inside
Non-blocking, full-line speed, store-and-forward operation
Support normal Ethernet frames and jumbo frames from 64 bytes to 9216 bytes
Auto-negotiation and auto-MDIX on all 10/100/1000M copper ports
16 mini-GBIC ports with optional fiber transceivers and 8 10/100/1000 RJ-45 ports
512 K bytes packet buffer, 8K MAC entries
Web-based interface for system management via the Ethernet connection
Provide the command line interface (CLI) for simple system setup via the RS-232 port
Support port-based VLAN and 802.1Q (tag-based) VLAN
Up to 4 trunk groups, maximum 8 member ports for each trunk with fail-over function
Support flow control for both half- or full-duplex operation
Support port mirror
Provide port statistics
Support 802.1P QoS (Quality of Service) with 4 queues
Support rate and broadcast storm control
Support port security to prevent flooded traffic
Support firmware update via TFTP transaction
Support configuration backup and restore via TFTP transactions♣
LED display for each port to show link and activity status
Wall mount, Rack mount or desktop
®
Broadcom is registered trademark of Broadcom Corporation
♣
Some models don’t support this function
5
1.1 Start to Manage This Switch
Plug-in the power source to power-up the switch. After the switch is powered-on and in ready state
(both the LED indicators POWER and DIAG are lighting), you can use any in-band Ethernet port to
remotely manage this system through the web browser, or use the RS-232 cable to plug-in the
console port (on the rear panel) to locally do the simple system configurations by using the
command line interface (CLI). The default IP and related settings for this interface are shown as
following:
IP address: 192.168.223.100
Network mask: 255.255.255.0
Default gateway:192.168.223.254
Try to use the default IP shown above to PING the switch from your PC to make sure the network
connection is successful. The default IP address on this switch can be modified later for your need. If
you encounter the access problem by using wrong IP addresses, just locally connect to console port
to get the correct IP address in this system.
Now you can use the browser to start to launch to the user-friendly web-managed interface for this
switch.
The login dialog box (shown as below) will show up first when the switch’s IP address is provided
through your browser.
Use the default username and password shown as below to complete the login procedure:
Username: admin
Password: 123
This username/password can be modified for your need.
6
1.2 Configuration Functions for the Switch
After the login is successfully validated, the switch’s home page – System page will show up. The
left part on the page provides the function menus (shown as below) to activate to the individual
configuration page.
The function menus contain two parts: Switch for setting up the switch functions and System for
maintaining the system parameters.
Switch functions contain:
Port Status – to show port link status and configure port parameters
Port Statistics – to show packet statistic results passed through each port
VLAN – to configure port-based or 802.1Q (tag-based) VLAN
Trunk – to build up the trunk function
Mirror – to setup the port mirroring function
QOS – to configure the Quality of Service function
Rate / Storm Control – to limit the traffic rate and suppress the broadcast storm
System functions contain:
System Setup – to configure the required system information (such as IP address, etc.)
User Management – to maintain the login information to access to the switch
Backup / Restore♣ – to backup/restore configurations to/from TFTP server
Reboot / Reset – to reboot the switch or reset configuration to default values
Logout – to log off the system
♣
Some models don’t support this function
7
2 Configurations
2.1 Port Status
This page provides the current link status for all ports. You can select the Port Status menu to
activate this page and to refresh the current port status.
This page provides the following information:
Port – to specify a port on the switch
Link Status – to show the port link status: Up / Down
Speed / Duplex – to show the current link speed (1G / 100M / 10M bps) and duplex mode
(Full / Half) while the port is linkup.
NOTE: Only the full duplex mode is supported while the link speed is 1Gbps.
Flow Control – to show the flow control capability is Enable / Disable for this port.
The status for the two columns: Speed/Duplex and Flow Control won’t show up while the port link
is down. (The dash sign (‘--‘) indicates the status is unavailable to display.) Click the Refresh button
to manually get the most current link status for all ports.
If any trunk group is setup, a trunk group can be regarded as one logical port (e.g. Trk1 in above
figure is grouped by Port9 & Port10) which will show up just like the others. All the trunk member
ports won’t be displayed. Section 2.5 (Trunk) describes the port trunking in detail.
8
2.2 Port Configuration
If you need to do the port configuration, just select one desired port by clicking the Port number in
the Port Status page. Then the Port Configuration page (shown as below) for the selected port (e.g.
port3) will be opened:
The following parameters will be provided and configured in the Port Configuration page:
Port – the selected port number to be configured (read only)
Admin – to unblock/block the traffic for the port
¾ Disable – to block all traffic for the port
¾ Enable – to enable the bi-directional traffic for the port
Auto Negotiation – to enable/disable the capability of auto negotiation for setting up the link
¾ Disable – to disable for the port (force mode)
¾ Enable – to enable for the port (auto mode)
Speed / Duplex – to setup the link speed and duplex mode in force mode
The options for this function can be selected only when the Auto-Negotiation is Disabled (in
force mode) for copper ports (Port17 to Port24). At this moment, there are 4 options for this
parameter:
¾ 100Mbps Full – to set the speed 100Mbps in full duplex mode
¾ 100Mbps Half – to set the speed 100Mbps in half duplex mode
¾ 10Mbps Full – to set the speed 10Mbps in full duplex mode
¾ 10Mbps Half – to set the speed 10Mbps in half duplex mode
The following figure shows the options of Speed / Duplex while Disable is selected in
auto-negotiation field for copper port (e.g. Port17).
9
NOTE: Only full duplex mode is supported in 1Gbps link speed. For copper medium, this
system doesn’t support 1Gbps link speed in force mode; for fiber medium, only the 1Gbps
link speed is supported, but either auto or force mode can be set to build up the link.
Flow Control – to enable/disable flow control function
¾ Disable -- to disable for the port
¾ Enable – to enable for the port
Default Priority – to setup the priority of frames which will referenced in QOS function
¾ 0 – 7 – to set the priority level (range = 0 ~ 7)
Security – to enable/disable port security function
If the per-port security is enabled and if a received frame contains a source MAC address that
has already been learned in another port’s address table but not aged out, then the frame is
dropped. Otherwise, the address table entry is updated with the new port’s information and the
entry is updated.
¾ Disable -- to disable port security
¾ Enable – to enable port security
Jumbo Frame – to enable/disable jumbo frame function
If the per-port jumbo frame feature is enabled, the maximum frame size is 9216 bytes. In 100
Mbps mode, the maximum jumbo frame size supported is 9000 bytes
¾ Disable -- to disable jumbo frame support
¾ Enable – to enable jumbo frame support
After the desired options are selected for the above functions, click the Apply button to save the
current settings to the switch and back to the Port Status Page. Click the Cancel button to back to
Port Status page.
10
2.3 Port Statistics
Port Statistics function will let you to see the TX/RX packets through each port.
Clear Counters button will clear all packet counters to 0. Refresh button will get port statistics again.
You can check each port statistics more precisely. Just click the Port number to see the detailed
information.
11
The table shown as below is description for each column.
UnicastPkts
MulticastPkts
BroadcastPkts
Single Collision
Multi Collisions
64 BytePkts
65-127 BytePkts
128-255 BytePkts
256-511 BytePkts
512-1023 BytePkts
1024-1522 BytePkts
Number of good unicast packets transmitted.
Number of good multicast packets transmitted.
Number of good broadcast packets transmitted.
Number of packets in which the transmission experienced one collision
Number of packets in which the transmission experienced over two collisions
Number of packets(including bad ones) transmitted that were 64 Bytes in
length
Number of packets(including bad ones) transmitted that were 65-127 Bytes
in length
Number of packets(including bad ones) transmitted that were 128-255 Bytes
in length
Number of packets(including bad ones) transmitted that were 256-511 Bytes
in length
Number of packets(including bad ones) transmitted that were 512-1023
Bytes in length
Number of Non-Jumbo packets(including bad ones) transmitted that were
FCSErrors
AlignErrors
SymbolErrors
FragmentPkts
OverSizePkts
1024-1522 Bytes in length
Number of packets received of proper-size with CRC error and integral
octets
Number of packets received of proper-size with CRC error and non-integral
octets
Number of packets received of proper-size that experienced symbol error
during reception
Number of packets received that were less than 64 bytes without CRC or
alignment error
Number of packets received that were greater than the maximum length
without CRC or alignment error
12
2.4 VLAN
VLAN function provides the capability of creating virtual LAN groups for network group
management, security and performance considerations. The main purpose of setting VLAN is to
limit the traffic only flow within the port members which belong to the same VLAN group. The
traffic including broadcast packets in a VLAN group will be isolated from different groups.
This system supports both port-based VLAN and IEEE 802.1Q (tag-based) VLAN. Port-based
VLAN provides the VLAN function only for local switch. Tag-based VLAN is capable of working
with other switches to achieve the VLAN function by tagged traffic.
Just click the VLAN menu item, the VLAN Configuration page is displayed shown as blow. This
page provides the current VLAN type and the place to do advanced VLAN configuration if the
Configure button is available.
Three options of VLAN type are provided:
Disable – to disable VLAN function. All existing VLAN groups will be removed. PVID for all
ports will be reset.
Port-based VLAN – to enable port-based VLAN. All existing tag-based VLAN group will be
removed. PVID for all ports will be reset.
IEEE 802.1Q VLAN – to enable tag-based VLAN. All existing port-based VLAN groups will
be removed.
The VLAN type can be either port-based or tag-based. That is, both the port-based VLAN and
802.1Q VLAN can’t co-exist at the same time.
The Configure button will be enabled to click for advanced VLAN configuration only when the
current VLAN type is activated to port-based or tag-based VLAN; otherwise, this button will be
disabled.
13
2.4.1 Port-based VLAN Configuration
The port-based VLAN divides the ports into different Virtual LAN domain groups. After setting the
port -based VLAN, the different VLAN groups can’t access each other. Like the different real LAN
can’t access each other. Before starting this configuration, it is required to set the VLAN type to
port-based VLAN first. Then click the Configure button after the port-based VLAN type is activated
(shown as figure below).
VLAN initial setting page is shown as below:
You can add, delete, and modify the port-based VLAN for your need. Currently this system supports
up to 32 port-based VLAN groups for manual entry. The next pages will be described in detail how
to configure the port-based VLAN.
NOTE: The default port-based VLAN group (No.1) always exists and can’t be removed. This
group needs to be manually maintained to make this function work properly. Initially, the
default group contains members for all ports. If a new group is created (e.g. port 1, 2, 3 as
members of group No.2) and this group wants to be isolated from the other ports, port 1, 2 and
3 in default group need to be manually set to “Not member” to make port-based VLAN group
No.2 available. Of course, manually set corresponsive port(s) to “Member” in default group as
your need if a group wants to be removed.
14
2.4.1.1 Add Port-Based VLAN Groups
To add a port-based VLAN group, select the “Create New VLAN” in VLAN NO dropdown of the
Port-Based VLAN Configuration page shown as below:
After selecting the Create New VLAN in the dropdown, the page will be changed like this:
In the above page, VLAN NO will auto setup. Users just need to set VLAN Port Members. After
setting complete, press the Create button will come back to the VLAN initial setting page. The
Cancel button can let user to give up the settings and back to the VLAN initial setting page.
15
Below is the example page when user sets Port1-12 to the VLAN Group2 after clicking the Create
button. Now there is a VLAN group No.2 created with the member Port1-12.
While the group No.2 is created, all the members in group No.1 are removed to availably operate the
VLAN function.
16
2.4.1.2 Delete Port-Based VLAN Groups
To delete a port-based VLAN group, just select a desired group (e.g. No.2) to be removed and click
the Remove This VLAN button to do the deletion.
After pressing the Remove This VLAN button and this action is confirmed, the result is in the
following figure.
Now all ports are set to the members in VLAN group No.1 to retain the system back to the normal
operation.
17
2.4.1.3 Edit Port-Based VLAN Groups
To edit the current port-based VLAN group, first select the existing group (e.g. group No.3 with
members from Port9 to Port12) you want to edit (to add Port7 & Port8 as members) and click the
Apply button to activate the setting.
The following figure shows the latest configuration for the selected group (e.g. No.3).
18
2.4.2 802.1Q VLAN Configuration
IEEE 802.1Q (tag-based) VLAN can add or strip 802.1Q tag depending on the requirements of the
individual transmitting port. It is required to click the VLAN menu item to set the VLAN type to
IEEE 802.1Q VLAN in VLAN Configuration page before doing the advanced configuration.
Click the Configure button to open the configuration page after the IEEE 802.1Q VLAN type is
activated (shown as figures below).
The group with VLAN ID 1 stands for the default 802.1Q VLAN group. This default group can’t be
deleted. However, the port members in this group can be modified. In default setting, all 24 ports are
the untagged members of this group with port VID value 1. Currently this system supports up to 32
tag-based VLAN groups for manual entry.
NOTE: Please be aware that this system currently has a constraint for web configuration in
802.1Q VLAN environment. This switch doesn’t allow web configuration from multiple VLAN
groups. That is, web configuration can be done through ONLY ONE specified VLAN group
(default VLAN group with VID=1 in default). Specify one VLAN group (e.g. VID=2) for
allowing to web-manage the switch and use console to set the PVID value (e.g. PVID=2) for
admin port (Port25), then web management can be achieved only through VLAN group
members with VID=2.
19
Loading...