AirLive BC-5010-IVS User Manual

BC-5010 / BC-5010-IVS

5-Mega Pixel Box Type PoE IP Camera

5-Mega Pixel Box Type PoE IP Camera with Video Analytics

User’s Manual

No part of this publication may be reproduced in any form or by any means, whether electronic, mechanical, photocopying, or recording without the written consent of OvisLink Corp.

OvisLink Corp. has made the best effort to ensure the accuracy of the information in this user’s guide. However, we are not liable for the inaccuracies or errors in this guide. Please use with caution. All information is subject to change without notice

This product contains some codes from GPL. In compliance with GPL agreement, AirLive will publish the GPL codes on our website. Please go to www.airlive.com and go to the "Support->GPL" menu to download source code.

All Trademarks are properties of their respective holders.

i AirLive BC-5010/BC-5010-IVS User’s Manual

FCC Statement

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the A user is encouraged to try to correct the interference by one of the following measures:

 Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

WEEE Marking Warning:

The crossed out wheeled bin indicates the product must not be disposed together with household waste. For the sake of the environment, the product should only be given to entities involved in the reception of waste electronic and electrical equipment. The lists of entities entitled to receive used equipment can be found on the websites of municipalities. Some components of devices such as external wiring, circuit boards and liquid crystal displays have a negative impact on the environment.

AirLive BC-5010/BC-5010-IVS User’s Manual ii

Table of Contents

1. Overview .....................................................................................................1

1.1 Introduction ..........................................................................................1

1.2 Features...............................................................................................2

1.3 Product Specification ...........................................................................2

1.4 System Requirement ...........................................................................5

2. Package Contents and Installation...........................................................6

2.1 Package Content .................................................................................6

2.2 Connections.........................................................................................7

2.3 Connections Mounting the Camera .....................................................9

2.4 Connect USB dongle for wireless function (Optional)........................13

2.5 Connect to IP Camera .......................................................................13

3. Using IP Camera via Web Browser.........................................................15

3.1 Windows Web Browser......................................................................15

4. Operating IP Camera via Mobile Phone .................................................17

4.1 Using IP Camera via iPhone..............................................................17

5. Configuration of Main Menu....................................................................19

5.1 Live View............................................................................................20

5.2 Configuration .....................................................................................21

6. Configuration-Network ............................................................................23

6.1 General ..............................................................................................24

6.2 UPnP/Bonjour/QoS............................................................................26

6.3 IP Filter...............................................................................................27

6.4 IP Notification.....................................................................................28

6.5 iSCSI..................................................................................................29

6.6 Wireless .............................................................................................29

7. Video Settings ..........................................................................................31

7.1 Video Profile.......................................................................................32

iii

AirLive BC-5010/BC-5010-IVS User’s Manual

Table of Contents

7.2 Exposure............................................................................................32

7.3 Image.................................................................................................34

7.4 WDR ..................................................................................................35

7.5 Overlay ..............................................................................................36

8. Audio.........................................................................................................37

8.1 Audio Setting......................................................................................37

9. Event .........................................................................................................38

9.1 Event..................................................................................................38

9.2 Event Schedule..................................................................................40

9.3 Motion Detection................................................................................41

9.4 Tamper Detection...............................................................................42

10. RS-485.....................................................................................................43

10.1 RS-485 Settings...............................................................................44

10.2 RS-485 PTZ.....................................................................................44

11. System ....................................................................................................45

11.1 Device Settings ................................................................................46

11.2 Account ............................................................................................46

11.3 Management Ports...........................................................................48

11.4 Firmware ..........................................................................................48

11.5 Maintenance.....................................................................................49

12. Status ......................................................................................................50

12.1 Basic ................................................................................................50

12.2 Audio/Video......................................................................................50

12.3 Network............................................................................................51

12.4 System Log......................................................................................52

13. Video Analytics ......................................................................................53

13.1 Video Analytics (Only for BC-5010-IVS) ..........................................53

14. Appendix.................................................................................................61

A. Alarm I/O Connector............................................................................61

AirLive BC-5010/BC-5010-IVS User’s Manual iv

1. Overview

This user’s guide explains how to operate this camera from a computer. User should read this manual completely and carefully before you operate the device.

1.1 Introduction

AirLive BC-5010 / BC-5010-IVS is a standalone system that can be connected directly to an Ethernet or Fast Ethernet network.

Equipped with a powerful 5 megapixel color CMOS sensor, the camera allows you to capture a wider field of view with high resolution up to 2592 x 1920. With supporting of latest H.264 technology, you can record the video streaming that utilizes with high quality H.264 images to any external storages, enables motion detection and automatic e-mail alerts for security.

The camera supports external DC-Iris lens. It also provides the power and control signals which is required to adjust the DC-lris. The DC-Iris connector (4-pin) is on the side panel of the camera. You can attach any standard DC-Iris lens for specific use, such as outdoor applications with water-proof enclosure. In addition, the camera can attach a variety of external devices for your specific purposes through the GPIO connectors.

BC-5010 / BC-5010-IVS features web-based solutions that can provide a cost-effective solution to transmit the real-time high-quality video images and sounds synchronously for monitoring. This camera can be managed remotely, so that you can use a web browser to access and control it from any desktop/notebook computer over the Intranet or Internet.

With IEEE802.3af PoE (Power over Ethernet) standard, the camera provides you more flexibility of camera installation according to your application. The camera can be powered by the Ethernet, so that you can place the camera anywhere without a power outlet support.

Note: Lens is not included in the product package.

AirLive BC-5010/BC-5010-IVS User’s Manual

1. Overview

1.2 Features

This manual will illustrate the steps of how to setup and operate this IP camera, so you’ll also soon be enjoying the benefits of these product features:

 5 megapixel high resolution CMOS sensor  0.2Lux at F1.2  DC IRIS and IR-CUT Removable (ICR)  Multiple Profiles Supported(H.264, MPEG4, MJPEG and 3GPP)  Support 15fps at 2592x1920  Two-way audio  Intelligent motion detection up to 3 zones  Support iSCSI, WDR enhanced  HTTP/RTSP protocols selectable  Image transmission using an FTP or e-mail for event  Digital I/O connectors and RS-485 supported  802.3af PoE support  USB wireless dongle support (with adaptor only)  SD/SDHC Slot and USB slot for local storage  Compatible with ONVIF standard  Built-in Video Analytics (Equipped only for BC-5010-IVS)  UPnP device discovery and NAT router transversal for easy installation  Dynamic IP Service, DIPS®, to search your IP camera from Internet easily

1.3 Product Specification

Model BC-5010/BC-5010-IVS

Camera

Camera Type Indoor Box Type

Image Sensor 1/2.5” 5 megapixel CMOS Sensor

Sensor Resolution 2592 X 1920

C/CS Mount Lens Support

Lens Type

Removable Lens

Night Vision Built-In Removable IR Cut Filter

Max IR Distance None

Min. Illumination 0.2 LUX

AirLive BC-5010/BC-5010-IVS User’s Manual 2

Mechanical IR-Cut

Yes

Filter

Auto Iris DC-Iris Support

Viewing Angle Depend on lens

Pan/Tile Control None

Analog Video Out Yes

1. Overview

Video

Video Compression

H.264 High/Main/Baseline Profile, MPEG4 Simple Profile and MJPEG

Video Profile Yes

15 fps @ 2592 X 1920

25 fps @ 2048 x 1536

30 fps @ 1920 x1080

30 fps @ 1280 x 1024

Resolution and Frame Rate

30 fps @ 1280 x960

30 fps @ 1280 x 720

30 fps @ 720 x 480

30 fps @ 640 x 480

30 fps @ 320 x 240

30 fps @ 176 x 144

Multi-profile streaming

Streaming over UDP, TCP, or HTTP

MJPEG streaming over HTTP (for non IE browser)

Streaming

3GPP mobile view

Audio

Network

Configurable frame rate and bandwidth

Support both CBR and VBR

ROI Yes

AE, AWB

Saturation, brightness, sharpness, contrast, Hue

Image Processing

Mirror/Flip

Text, time and date OSD

Digital Zoom 10X

G711 u-law

Audio Encoder

AMR

Audio Streaming Two-way

Audio Input/Output speaker port and microphone port

One RJ45 Port; IEEE 802.3u Compliant 10/100 Mbps

Ethernet

Fast Ethernet with Auto-MDIX

AirLive BC-5010/BC-5010-IVS User’s Manual

1. Overview

PoE IEEE802.3af

Wireless Optional

TCP/IP,IPV6, UDP, ICMP, DHCP, NTP, DNS, DDNS,

Supported Protocols

Security

Users Up to 20 simultaneous users

Power LED Amber Color

LED and

Link/Act. LED Green Color

Button

Reset Button

Network Processor DSP Base

System ROM 128MByte NAND Flash

System RAM 128Mbyte DDR2 SDRAM

Power Supply DC12V

Power Consumption 4 Watts Max.

SMTP, FTP, HTTP, HTTPs, Samba, PPPoE, UPnP, Bonjour, RTP, RTSP, RTCP, DLNA, ONVIF, ISCSI

Password protection

IP filter

HTTPS

Reboot and Factory Default (Push and Hold Over 5 Sec)

RJ-45 10BaseT/100BaseTX

12V DC power jack

General

System Integration

Connector

Microphone/Speaker jack

DIDO

Reset button

Operation: Temp: -5℃ ~ 55℃ Humidity: 20% ~ 85% non-condensing

Environment

Storage: Temp: -15℃ ~ 60℃ Humidity: 0% ~ 90% non-condensing

SD card slot SD/SDHC

Dimension 135 * 65 * 65 mm

CamPro Express 64,CamPro Professional

Software

Search & Installation- IP Wizard II

Motion detection

Event Triggers

External input via DI interface

Motion Detection 3

Event handler

FTP or NAS file upload

E-mail alert

HTTP, and TCP notification

AirLive BC-5010/BC-5010-IVS User’s Manual 4

DO (digital output) alarm

SD/USB file upload

UPNP Yes

1. Overview

Viewing System

Application Programming Interface

ONVIF 2.2

Open API for software integration

SDK

Video Buffer Pre- and post- alarm buffering

File upload via FTP or email

Notification via email, HTTP, and TCP

Alarm Events

External output activation

Save to SD card/USB

Continuous

Yes

recording

OS Windows® XP, Vista, 7, 8

IE 7.0 or later, Firefox 2.0 or later, Safari, Google

Browser

Chrome

With 3GPP player, CamPro Mobile for iOS/Android

Cell Phone

device

Video Player VLC, Quick Time, Real Player, Core Player

1.4 System Requirement

For normal operation and viewing of the network camera, it’s recommended that your system meets these minimum requirements for proper operation:

Item Requirements

CPU Pentium-4 2.0 GHz or higher

VGA Monitor Resolution1280 x 1024 or higher

RAM 1 GB or more

Operating System Windows XP, Vista, 7, 8

Web Browser

Internet Explorer 7 or later;

2.00 or above; Google Chrome

Note: Please keep updating the latest Windows software and service package.

pple Safari 2 or above; Firefox

(Ex: Net Framework, Windows Media Player, Enhance ActiveX Security

AirLive BC-5010/BC-5010-IVS User’s Manual

2. Package Contents and Installation

2. Package Contents and

Installation

2.1 Package Content

A user can find the following items in the package as below:

1. AirLive BC-5010/BC-5010-IVS is the main part of the product with Camera Mount Kit.

Note: The lens is optional. For further information about the lens, please contact with

your installer.

2. Power Adapter: DC 12V/1A

3. User’s Manual CD provides installation software, application program, important

information and instructions for operating the Network Camera.

4. Quick Setup Guide provides important information and instructions for installing this device.

If any of the above items are missing, please contact your dealer immediately.

Note: 1.) Using a power supply with a different voltage than the one included with the

Network Camera will cause damage and void the warranty for this product.

2.) This product does not come with lens. It is optional.

AirLive BC-5010/BC-5010-IVS User’s Manual 6

2.2 Connections

Front / Top / Side Panel

2. Package Contents and Installation

1. DC-iris Connector: It allows you to attach the DC-Iris lens (optional).

2. C and CS Lens Focus Ring: You can adjust C and CS lens focus ring to fit your lens

type.

Back Panel

AirLive BC-5010/BC-5010-IVS User’s Manual

2. Package Contents and Installation

1. RJ45 LAN socket: Connect to PC or Hub/Switch. This Ethernet port built N-Way protocol can detect or negotiate the transmission speed of the network automatically. Please use Category 5 cable to connect the Network Camera to a 100Mbps Fast Ethernet network switch or hub.

In the LAN socket, there are two LEDs below: LAN LED (green color) This LED will be flashing while network accessing via Ethernet. Power (orange color) This LED is used to indicate whether DC power is on or not. In addition, this LED will be flashing while the wireless accessing of the Camera.

2. GPIO/RS-485: Connect to a local keyboard controller.

 DI/ DO: Connect to sensor in and alarm out devices

Cable for I/O connectors:

PIN SPECIFICATION

RS-485 D+

Compliant to RS-485

RS-485 D-

Ground (Common) GND

Close circuit current maximum: 70mA AC or 100mA

GPIO Out

Output resistance: 30 ohm Open circuit voltage maximum: 240V AC or 350V DC

GPIO In #1

GPIO In #2

Action high voltage: 9~40 VDC Dropout voltage: 0 VDC

3. DC-in Jack: The input power is DC 12V/1A.

Note that supply the power to the Network Camera with the power adapter included in package.

4. Audio I/O Connectors

 MIC in (audio in): Connect a microphone to the network camera.  Audio out: Connect a loud speaker to the network camera. This function is for

voice alerting and two-way audio.

5. Iris Level: It is used only when the DC-Iris lens is connected to the camera. This screw-knob allows you to adjust the brightness of the video images from the DC-Iris lens.

AirLive BC-5010/BC-5010-IVS User’s Manual 8

2. Package Contents and Installation

6. SD Card Slot: SD Card Slot allows you to insert a memory card for expansion of storage.

7. USB Port: USB Port connects external USB device, such as flash drive or USB wireless adapter.

8. BNC connector: BNC connector can connect monitor to check camera focus and video quality.

9. Reset Button: This button is used to restore all the factory default settings. Sometimes restarting the device will make the system back to a normal state. However, if the system still has problems after restart, user can restore the factory default settings and install it again.

Restore the device:

1.) Press the button down continuously.

2.) Hold the button at least 5 seconds and release it. Then the device has been restored to default settings and reboot again.

Note: Restoring to the factory default settings will lose all the previous settings included IP address forever. User needs to run the IP Wizard II program to search the device and configure it to let the device work properly again.

2.3 Connections Mounting the Camera

1. Attaching the Wall Mount Kit

The Wall Mount Kit that is provided in the package has a swivel ball screw head, so that you can attach it to the screw hole on the camera’s top (or bottom) panel. After attaching the camera to the Wall Mount Kit, the camera can be mounted on the wall or ceiling securely through the three screw holes on the base of the Wall Mount Kit. Fix the camera to ceiling with the three supplied screws.

AirLive BC-5010/BC-5010-IVS User’s Manual

2. Package Contents and Installation

2. Connecting to LAN

You can use the provided Ethernet cable to connect the camera to your local area network (LAN). When you connect the AC power adapter, the camera is powered on automatically. You can verify the power status from the Power LED on the Ethernet port. Once connected, the Link LED starts flashing green light and the camera is on standby and ready for use now.

AirLive BC-5010/BC-5010-IVS User’s Manual 10

2. Package Contents and Installation

3. Connect the external power supply to Camera Connect the attached power adapter to the DC power jack of the camera.

Note: Use the 12VDC power adapter, included in the package, and connect it to wall

outlet for AC power. Once you have installed the camera well and powered it on, the power LED (orange) will turn on later. When the power LED turned on, it means that the system is booting up successfully. Furthermore, if you have a proper network connection and access to the camera, the LAN LED (green) will flash.

4. Replacing the Lens Assembly

The camera is designed with a CS- mount, allowing you to install any standard C or CS lens that are commonly used in the surveillance application.

 Installing the Lens Assembly To install new lens assembly, follow the instructions below:

1. Remove the protective cap.

2. Fit the C or CS lens onto the CS-mount ring and screw it in clockwise.

3. Plug the cable to the DC-Iris connector on the side panel of the camera.

When you use a DC-Iris lens on your camera, you can adjust the brightness of the video image through the Iris Level screw-know on the back panel of the camera.

AirLive BC-5010/BC-5010-IVS User’s Manual

2. Package Contents and Installation

 C and CS Lens Focus Adjustment

You can adjust C and CS lens focus ring to fit your lens type.

5. Applications of the Camera

The camera can be applied in multiple applications, including:

z Monitor local and remote places and objects via Internet or Intranet. z Capture still images and video clips remotely. z Upload images or send email messages with the still images attached.

The following diagram explains one of the typical applications for your camera and provides a basic example for installing the camera.

Home Applications of the Internet Camera

AirLive BC-5010/BC-5010-IVS User’s Manual 12

2. Package Contents and Installation

2.4 Connect USB dongle for wireless function (Optional)

You can add wireless function to your BC-5010 / 5010-IVS by connecting the optional wireless USB dongle.

2.5 Connect to IP Camera

1. Insert the bundle CD into your PC/Laptop.

2. Auto Run Screen then shows up; click “Install Software Æ “IP Wizard II” to install the configuration tool software.

AirLive BC-5010/BC-5010-IVS User’s Manual

2. Package Contents and Installation

3. After completing installation, run the configuration tool software.

4. The Software scans the network and finds the IP Camera and then lists them in the dialog box.

5. If the Camera’s IP address is in the same IP segment as your LAN, select the founded IP Camera and double click on the item. Then, the default browser will show up and connect to the IP camera’s Web automatically.

AirLive BC-5010/BC-5010-IVS User’s Manual 14

3. Using IP Camera via Web Browser

3. Using IP Camera via Web

Browser

3.1 Windows Web Browser

1. Open your web browser, and enter the IP address or host name of the IP camera in the Location / Address field of your browser. Note: If you only want to view the video without accessing Setting screen, enter “http://<IP>/index2.htm” as your web URL.

2. Use the default account “admin” and default password “airlive”.

Note: The default user name “admin” and the password “airlive” are set at the factory for the administrator.

3. According your browser’s security setting, the IE Web Page may prompt the “Security Warning” window. If so, select “Yes” to install and run the ActiveX control into your PC. Otherwise, the system will load the ActiveX silently.

4. After the ActiveX control was installed and ran, the first image will be displayed.

AirLive BC-5010/BC-5010-IVS User’s Manual

3. Using IP Camera via Web Browser

5. The monitor image will be displayed in your browser. In the left side of main configuration is “Configuration”. For more details, you can check the following chapters.

AirLive BC-5010/BC-5010-IVS User’s Manual 16

+ 46 hidden pages