Aiphone JS-1HD Installation Manual

PS-2420BF, PS-2420DM

Installation Manual

JSS-1A (A set includes JS-1MD, JS-DA, and power supply) JS-1HD (Sub monitor station)

Issue date: Oct. 2019 FK2685 A P1019 AQ 61458

Parts names

JS-1MD / JS-1HD

The illustration is JS-1MD.

Door release button

Audio transmit LED (orange)

Power switch

Talk/Off button

Color LCD screen

Remove protective lm before use, if attached.

Microphone Monitor button Screen brightness

control button

Volume control button

Speaker

JS-DA

Camera-angle adjustment lever

The camera-angle adjustment lever is on the back of the door station.

[Back side]

Camera-angle adjustment lever

Call button White light LED

Cable inlet holes

Camera

Microphone

Mounting frame

Front panel

Speaker Location LED (red)

Drainage holes

Included accessories

Installation manual x1

(this manual)

Information sheet x1

Mounting bracket x1

(attached to the monitor station)

NOTES:

Mounting and wood mounting screws not included.

•

For details on the power supply, see the installation manual of the power supply separately.

•

Front panel x1

(attached to the door

station, JSS-1A only)

Caution (Negligence could result in injury to people or damage to property.)

1. Do not install or connect the station with the power on. This may result in electrical shock

or malfunction.

2. Make sure the wiring is correct and there are no wiring shorts before switching on the station. This may result in re or electrical shock.

3. Install in a place where the station will not get easily bumped. This may result in injury.

4. Do not put your ear close to the speaker when using the station. May cause harm to the ear if a sudden loud noise is emitted.

Precautions for mounting

1. The monitor station is designed for indoor use only. Do not install at outdoor location.

2. Installing the device in the following locations could cause malfunction:

* Locations under direct sunlight (except door station) * Locations near heating equipment * Locations subject to liquid, iron lings, dust, oil, or chemicals * Locations subject to moisture and humidity extremes * Locations where the temperature is quite low * Locations subject to steam or oil smoke * Sulphurous environments * Locations close to the sea or directly exposed to sea breeze

3. Installing the station in the following locations as is may affect the clarity of the image:

* Where lights will shine directly into the camera at night time * Where the sky lls much of the background * Where the background of the subject is white * Where sunlight or other strong light sources will shine directly into the camera

Where the sky fills much of the background

Sky

4. In 50Hz regions, if a strong uorescent light enters directly into the camera, it may cause the image to icker. Either shield the camera from the light or use an inverter uorescent light.

5. Use a parallel 2 conductor cable to connect the door station.

6. For wiring, separate them for audio/video and door release and keep them more than 10cm (3-15/16”) away from each other.

7. If exisiting wiring is used, the device may not operate properly. In that case, it will be necessary to replace the wiring.

8. Do not use any impact driver to fasten screws. Doing so may cause damage to the device.

9. Do not install the product on a recessed wall to avoid interruption of communication.

10. Using a single multi-conductor cable for multiple connections may result in poor image quality.

Where the background of the subject is white

White

wall

Where sunlight or other strong light sources will shine directly into the camera

Wiring method, wiring distance

JS-DA

JS-1MD

JS-1HD

B B

: PS-2420, PS-2420S, PS-2420UL,

PS24

Ø 0.65 mm 22 AWG Ø 0.8-1.2 mm 20-16 AWG

A 50 m 165′ 100 m 330′

B 5 m 16′ 10 m 33′

Installation

Cable

Use PE (polyethylene)-insulated PVC jacket

•

cable. Parallel or jacketed 2-conductor, mid-capacitance non-shielded cable is recommended.

Never use individual conductors, twisted pair cable or coaxial cable.

•

To connect low voltage wires, either crimp them with a crimp sleeve or solder them, and then insulate by covering with insulating tape.

[Crimping with a crimp sleeve]

1. Line up solid and stranded conductors,

and crimp them.

Solid conductor

Stranded conductor

[Soldering]

1. Twist the stranded

conductor around the solid conductor at least three times.

Solid

conductor

Stranded

conductor

Crimp sleeve

2. Bend the tip and solder it. Make sure no lead wire

sticks out.

2. Overlap more than half

Soldering

of the width and twist them at least twice.

Insulating tape

3. Overlap more than half of the width and twist them at least twice.

Insulating tape

Precautions

Prohibited

Do not dismantle unit

Be sure to follow the instruction

Warning (Negligence could result in death or serious injury.)

1. Do not disassemble or modify the station. This may result in re or electrical shock.

Do not use with a power supply rated above the specied voltage. This may result in re or

electrical shock.

3. Do not install two power supplies in parallel to a single input. This may result in re or

electrical shock.

4. Do not connect any terminals on the station directly to an AC power line. This may result in

re or electrical shock.

Use the Aiphone power supply specic for use with the system. This may result in re or

malfunction.

General Precautions

1. Install low-voltage lines at least 30 cm (12”) away from high-voltage lines (AC100V-240V), especially inverter air conditioner wiring. This may result in interference or malfunction.

2. When installing or using the station, give consideration to the privacy rights of subjects, as it is the responsibility of the system owner to post signs or warnings in accordance with local

ordinances.

Notice

1. If the station is used in areas where there are business-use wireless devices such as a transceiver or mobile phones, it may cause malfunction.

2. If the station is installed near a wireless device, interference may occur and could cause a

malfunction.

3. If the station is installed in an area with an extremely strong electrical eld, such as in the vicinity of a broadcasting station, it may create interference and cause a malfunction.

4. Internal and external temperature difference may cause condensation on the camera. Plugging cable holes and other gaps is recommended for preventing condensation.

• When using existing cables

Check for short circuit and disconnection before installation.

Ø0.8-1.2mm, 100m (20-16 AWG, 330’) Loop resistance value: 6Ω or less

Disconnection check (6Ω or less)

Connect the ends of one side and make a measure at the other side with a tester.

Connect the ends of one side.

Short circuit check: ∞Ω (Innity)

Disconnect

Measure the resistance of this loop.

Installation

Mounting

Installation location of the video door station and image view area

JS-DA

The angle of the camera lens can be adjusted in the range of 15° in the upward, right, and left directions and in the range of 7° in the downward direction.

The camera angle adjustment lever is at the back of the station.

Downward direction (up to 7°)

Angle adjustment lever

Right direction (up to 15°)

Upward direction (up to 15°)

Adjustment examples

To the center

(default)

The angle can also be adjusted to the right and right upward.

•

The image may be distorted when the angle is set to left upward or right upward.

•

Upward Downward To the left Left upward

• View area at 500 mm (20”) in front of the camera

Approx. 950 mm (3’1”)

Approx.

550 mm

(22”)

Vertical

Camera angle: 0° Camera angle: 15° Camera angle: −7°

Approx. 1,800 mm (5’11”)

Approx.

550 mm (22”)

Approx.

1,250 mm

(4’1”)

500

(20”)

Station

center

1,500 mm

(5’)

Approx. 1,850 mm (6’1”)

Approx.

650 mm (2’2”)

Approx.

1,200 mm

(3’11”)

Left direction (up to 15°)

Station

center

500

(20”)

1,300 mm

(4’3”)

( When the station is installed to

a high position due to a step)

Approx. 1,900 mm (6’3”)

Approx.

600 mm (2’)

Approx.

1,300 mm

(4’3”)

500

(20”)

150 mm

(6”)

Station

center

1,500 mm

(5’)

JS-1MD / JS-1HD

The illustration is JS-1MD.

Remove the mounting

bracket.

(The mounting bracket is

attached to the back of the station.)

Slide the mounting bracket downward to remove it.

Release button

Station

Mount the station on

the mounting bracket.

Connect wires.

1. Press the release button (to insert or remove the wire).

2. Insert the wire into the terminal.

Release button

Mounting bracket

Slide downward

Wood mounting screw × 2

(not included)

Screw shaft: Ø 4.1 or less Slotted head: Ø 8.2 or less,

3.0 mm or less in height

Mounting bracket

(attached to the station)

9 mm (3/8”)

Center of the monitor station

17 mm (11/16”)

Center of the mounting bracket

Fasten the

mounting bracket to the wall.

Place “ UP” upwards

83.5 mm (3-5/16”)

Wires

Mounting height

(center of the mounting bracket)

1,480 mm (4’ 10’’)

Cut a small round hole (Ø 50 mm (1-15/16″)) in the wall for routing wires.

* Cut a hole at a position shifted 17 mm

(11/16”) to the down from the station

center.

Center of the monitor station

83.5 mm (3-5/16”)

Mounting bracket

The wires can be routed to the top or bottom of the station. Cut the cable inlet to allow passage of the wiring into the station from the top or bottom

of the station.

If there is a large amount of wiring, strip away the jacket of the wire up to the cable inlet.

Cut the cable inlet at the top or bottom of the station.

(The gure shows the station with

the bottom inlet removed.)

Station

Wires

When the wood mounting screws cannot be used for plasterboard walls, concrete walls and so on, use commercially-available board

anchors or concrete plugs.

(e.g.)

Board anchor Concrete plug

Make sure to leave at least the specied spaces on all sides to prevent malfunction and

•

audio distortion.

Molding

Wood mounting screw × 2

(not included)

Screw shaft: Ø 4.1 or less Slotted head: Ø 8.2 or less,

3.0 mm or less in height

Use cable moldings for the power wire and the other wires. The open wire sections between

the station and the cable moldings should be

80mm (3-1/8”) or less.

Molding

Be sure to pass the wood mounting screws through the holes at the center.

The station cannot be installed

if the wood mounting screws

are inserted into other holes.

Place “ UP”

upwards

83.5 mm (3-5/16”)

Mounting height

(center of the mounting bracket)

1,480 mm (4’ 10’’)

Mounting bracket

(attached to the station)

80 mm (3-1/8”) or less

200 mm (7-7/8”)

Horizontal

Camera angle: 15°

500 mm (20”)

Approx. 750 mm (2’5”)

Approx. 1,000 mm (3’3”)

Approx.

250 mm

(9-13/16”)

Camera angle: 0° Camera angle: 15°

500 mm (20”)

Approx. 950 mm (3’1”)

Approx.

250 mm

(9-13/16”)

Approx. 1,000 mm (3’3”)

Approx. 750 mm (2’5”)

200 mm (7-7/8”)

500 mm (20”)

+ 1 hidden pages