FK1899 A P0713KD 55060
JOS-1A, JOS-1V, JOS-1F
HANDS-FREE COLOR VIDEO INTERCOM
INTERPHONE VIDEO COULEUR MAINS LIBRES
INTERCOMUNICACIÓN CON VÍDEO A COLOR MANOS LIBRES
HANDENVRIJE KLEURENVIDEOFONIE
VIDEOCITOFONO A COLORI A VIVAVOCE
FREISPRECH-FARBVIDEO-SPRECHANLAGEN-HAUPTSTELLE
INSTALLATION & OPERATION MANUAL
MANUEL D’INSTALLATION ET D’UTILISATION
MANUAL DE INSTALACIÓN Y OPERACIÓN
INSTALLATIE- EN BEDIENINGSHANDLEIDING
MANUALE D'INSTALLAZIONE E USO
INSTALLATIONS- UND BEDIENUNGSANLEITUNGHANDBUCH
JOS-1A
JO-DA
VIDEO DOOR STATION
JOS-1V
JO-DV
VIDEO DOOR STATION
MASTER MONITOR STATION
Thank you for selecting Aiphone for your communication and security needs. Please read this manual carefully for proper system
operation. For future reference, keep manual in a safe place.
JO-1MD
JOS-1F
JO-DVF
VIDEO DOOR STATION
PRECAUTIONS
Prohibited Do not dismantle unit Keep unit away from water General precautions
EnglishFrançaisEspañolNederlandsItalianoDeutsch
1.
2.
3. Comply with all third party manufacturing specications that will be used with this
4. If the unit is down or does not operate properly, unplug the power supply.
5. When wall-mounted, the top of the unit may darken. This does not indicate a
6. The unit case may become warm with use, but this is not a unit malfunction.
WARNING
Negligence could result in death or serious injury.
1.
Do not dismantle or alter the unit. Fire or electric shock could result.
2. Keep the unit away from water or any other liquid.
Fire or electric shock could result.
3. High voltage is present internally. Do not open the case.
Electric shock could result.
4. Do not connect any non-specied power source to the +, - terminals.
Also, do not install two power supplies in parallel to a single input.
Fire or damage to the unit could result.
5. Do not use power supply with a voltage other than specied.
Fire or electric shock could result.
6. Do not put any metal or ammable material into the unit through the openings.
Fire, electric shock, or unit trouble could result.
7.
The unit must be installed and wired by a qualied technician.
CAUTION
Negligence could result in injury or damage to property.
1. Do not install or make any wire terminations while power supply is plugged in. It
can cause electrical shock or damage to the unit.
2. When mounting the unit on a wall, install the unit in a convenient location, but not
where it could be jarred or bumped. Injury could result.
3. Before turning on power, make sure wires are not crossed or shorted. Fire or
electric shock could result.
4. Do not install the unit in locations subject to frequent vibration or impact. It may
fall or tip over, resulting in damage to the unit or personal injury.
5. For power supply, use Aiphone power supply model specied for use with system.
If non-specied product is used, re or malfunction could result.
6. Do not put anything on the unit or cover the unit with cloth, etc.
Fire or unit trouble could result.
7. Do not install the unit in any of the following locations.
Fire, electric shock, or unit trouble could result.
* Places under direct sunlight or near heating equipment that varies in temperature.
* Places subject to dust, oil, chemicals, hydrogen sulde (hot spring).
* Places subject to moisture and humidity extremes, such as bathrooms, cellars,
greenhouses, etc.
* Places where the temperature is quite low, such as inside a refrigerated area or
in front of an air conditioner.
* Places subject to steam or smoke (near heating or cooking surfaces).
* Where noise generating devices such as dimmer switches or inverter electrical
appliances are closeby.
* Locations subject to frequent vibration or impact.
8.
Do not apply high pressure on the screen. If fractured, injury could result.
9. If the LCD is punctured, do not allow skin contact with the liquid crystal inside.
Inammation could result.
* If liquid crystal is ingested, immediately gargle with water and seek medical
attention.
* If contact with the eyes or skin occurs, clean with pure water and seek medical
attention.
GENERAL PRECAUTIONS
Keep the unit more than 1m (3.3
Keep the intercom wires more than 30cm (12
induced noise and/or unit malfunction could result.
system (sensors, door releases, etc.).
malfunction.
') away from radio or TV set.
'') away from AC 100-240V wiring. AC
7. If the unit is used near a cellular phone, the unit may malfunction.
8. The unit can be damaged if dropped. Handle with care.
9. The unit will not work during power failure.
10. In areas where broadcasting station antennas are close by, the intercom system may be
affected by radio frequency interference.
11. All the units, except for door stations, are designed for indoor use only.
Do not use at outdoor locations.
12. This product, providing door release, should not be used as a crime prevention device.
13. Please note the LCD panel, though manufactured with very high precision techniques,
inevitably will have a very small portion of its image elements always lit or not lit at
all. This is not considered a unit malfunction.
14. Environmental sound around the unit may hinder smooth communication, but this is
not a malfunction.
15. At night, due to reduced lighting on the object, the screen sees more noise and faces
become more difcult to see, but this is not a malfunction.
16. For hands-free communication:
If you stand too far away, it may be difcult for the other person to hear the
communication.
17. If there are loud noises around the unit (such as music playing or children crying), the
sound may break up and be difcult to hear.
18. During communication, if you speak before the other person has nished talking, your
voice may not come through clearly.
Communication will proceed smoothly if you wait until the other person has nished
before speaking.
19. At a gate or porch illuminated by a uorescent lamp, the image may vary, but this is
not a malfunction.
20. The outline of video images displayed by the video door station may differ from that
of the actual person(s) or background, but this is not a malfunction.
21. If the surface of a video door station freezes during wintertime, the image may
become difcult to see or the call button may not move, but this is not a malfunction.
22. Warm-color lighting shining on the video door station may change the tint of the
image on the screen.
23. When outside temperature lowers sharply after rainfall, etc., the inside of the camera
may fog up slightly, causing a blurry images, but this is not a malfunction. Normal
operation will be restored when moisture evaporates.
24. When the unit’s screen is illuminated with strong light, the image looks white or
silhouetted, but this is not a malfunction.
NOTICES
* We will under no conditions be liable for damage occurring due to the inability to
communicate due to malfunctions, problems, or operational errors in this product.
* We will under no conditions be liable for any damages or losses resulting from this
product’s contents or specications.
* This manual was created by Aiphone Co., Ltd., all rights reserved. Copying, in part
or in whole, this manual without prior permission from Aiphone Co., Ltd. is strictly
forbidden.
* Please note that images and illustrations depicted in this manual may differ from the
actual ones.
* Please note that this manual may be revised or changed without prior notice.
* Please note that product specications may be changed for the sake of improvement
without prior notice.
* This system is not intended for life support or crime prevention. It is a supplementary
means of conveying information. Aiphone will under no conditions be liable for loss of
life or property which occurs while the system is being operated.
* Lighting adjustments are made automatically by the door station. Adjustment results
may vary depending on installation environment.
2
PACKAGE CONTENTS
JO-1MD
JOS-1A JOS-1V JOS-1F
English Français Español Nederlands Italiano Deutsch
Front panel Main unit
JO-DA
JO-DV
Flush mount
back box
JO-DVF
Manual
Special screw
x4
Special screwdriver
Special screwdriver (Hexagonal wrench)
Transparent name plate x2
NOTES:
• Mounting and Wood mounting screws
not included
• For details on the power supply, see
the installation manual separately.
3
Volume control button
PART NAMES
Remove protective film before use.
JO-1MD
Color LCD screen
Displays camera images during door
EnglishFrançaisEspañolNederlandsItalianoDeutsch
station call-ins, communication with door
station, and door station monitoring
Microphone
Sends sounds from this station
to other stations.
[Bottom View]
RESET button
Press this button to reboot this
station when it is not responding.
[During standby]
Adjust the calling volume.
Volume adjustment range: (mute), [During communication or monitoring]
Adjust the communication volume.
Volume adjustment range: -
Status LED (orange)
Indicates the current status of this station by lighting up or blinking.
On: During communication sending, while the door release button is
being pressed, or while the option button is being pressed
Flashing: During communication reception in the PTT mode, during
short detection or during mute
Monitor button
Monitor a door station
Option button
To activate/trigger external device
Screen brightness control button
Adjusts LCD screen brightness
Brightness adjustment range: -
Door release button
Unlocks door
Talk/off button
Starts or ends communication.
Speaker
Call tones, sounds from a door station.
Camera-angle adjustment switch
The camera-angle adjustment switch is behind
the panel. Pushing the button changes the angle
of the camera.
+17° (Upward)
+7° (Upward)
0° (Center)
-7° (Downward)
Camera-angle
adjustment switch
JO-DV
Illumination
sensor
Call button
JO-DA
Drainage holes
These are for discharging rain water inside the unit.
Do not obstruct these holes.
Camera
Microphone
White light LED
Speaker
Name plate
(with backlight)
The backlight is always lit while
the power is on.
Illumination
sensor
Camera
Captures images to display on the screens of
the master and expansion monitor station.
Microphone
Sends sounds from the door station to the
master and expansion monitor station.
Illumination sensor
Detects outside illuminance to recognize whether
it is daytime or nighttime.
Speaker
Outputs sounds from the master or expansion monitor station.
Call button with white light LED
Calls the preset master and expansion monitor station.
Lights up automatically when it gets dark around this station.
JO-DVF
Camera
Microphone
White light LED
Speaker
Name plate
(with backlight)
Call button
4
Vandal resistant front panel
Drainage holes
Vandal resistant front panel
INSTALLATION
In direct sunlight
Avoid installing the master monitor
Allow at least 15 cm (6") above
ab c
[Vertically]Camera angle: -7°
mm
Cable
Use PE (polyethylene)-insulated PVC jacket cable.
Parallel or jacketed 2-conductor, mid-capacitance, non-shielded
cable is recommended.
Wiring method, wiring distance
JO-DA
JO-DV
JO-DVF
A
JO-1MD
BC
: PS-1820, PS-1820S, PS1820UL, PS-1820D
PS18
Mounting locations
Do not install door station and master monitor station in any of the following locations where lighting or the ambient environment
could impact the display on the video monitor.
Never use individual conductors, twisted pair cable, or
coaxial cable.
Ø 0.65 mm 22 AWG Ø 0.8-1.2 mm 20-16 AWG
A 50 m 165' 100 m 330'
B 5 m 16' 10 m 33'
C 50 m 165' 150 m 495'
IER-2
English Français Español Nederlands Italiano Deutsch
JO-DA, JO-DV, JO-DVF
ab c
In direct sunlight
Under street lights or door lights
JO-1MD
station in a concave space
of a wall to prevent
disconnection of
communication
Mounting positions and image view area
JO-DA, JO-DV, JO-DVF
[Horizontally]
Approx. 950 mm
(3' 1")
[Vertically] [Vertically] [Vertically]Camera angle:
Approx. 1,800 mm
500
mm
(20")
Approx.
(5' 11")
Approx. 550 mm
(1' 9")
1,250 mm
(4' 1")
(20")
500
1,500 mm
mm
JO-DA: Refer to below diagrams when the camera angle is changed with the
adjustment switch.
Unit
center
(5')
0°
Approx.
Approx.
Approx.
1,750 mm
600 mm
(2')
1,150 mm
(3' 9")
(5' 9")
Camera angle: 7°
Other locations subject to strong
lighting or backlighting
conditions
and 25cm (9") below center of
the mounting
bracket for
installation
of the station
Camera angle: 17°
Approx.
1,900 mm
(6' 4")
650 mm
Approx.
Unit
center
(20")
1,300 mm
500
mm
(4' 4")
Approx.
(2' 2")
1,250 mm
(4' 1")
(20")
500
15 cm (6")
or more
25 cm (9")
or more
(When the station is at a high position due to a step)
Approx. 1,900 mm
(6' 4")
Approx.
600 mm
Unit
center
mm
1,300
(4' 4")
mm
(2')
Approx. 1,300 mm
(4' 4")
150 mm
(5")
(20")
500
mm
Unit
center
1,500
(5')
5
MOUNTING
JO-1MD
<Back wiring>
EnglishFrançaisEspañolNederlandsItalianoDeutsch
Fasten the mounting
1
bracket to the wall
Wires
3-gang box
2
83.5mm (3-5/16")
Mounting bracket
(attached to the unit with shipment)
1. Press release button to insert or remove wire.
2. Insert wire into the terminal.
Mount the unit on the
3
mounting bracket.
Mounting screw × 4
(Screw shaft: Ø4.1)
(Slotted Head: Ø8.2 or less
Height 3.0mm or less)
(not included)
8mm
(3/8")
<Surface wiring>
When the wiring is not coming through the wall, the wires can be routed to the top or bottom of the unit. Remove cable inlet plate on
the upper part of the unit to allow passage of the wiring into the unit.
Remove cable inlet plate
92mm (3-5/8")
Wires
83.5mm
(3-5/16")
Mounting bracket
(attached to the unit with
shipment)
6
Wood mounting screw × 4
(Screw shaft: Ø4.1)
(Slotted Head: Ø8.2 or less
Height 3.0mm or less)
(not included)
Place " UP" upwards
Mounting screw x 2
(Screw shaft: Ø4.1)
(Slotted Head: Ø8.2 or less
Height 3.0mm or less)
(not included)
Mounting screw x 2
(Screw shaft: Ø4.1)
(Slotted Head: Ø8.2 or less
Height 3.0mm or less)
(not included)
Main unit
1-gang box
Mounting frame
83.5 mm
(3-5/16")
83.5 mm
(3-5/16")
Mount the main unit on
the mounting frame,
and fit the front panel on.
Pry off the front panel with
a flathead screwdriver.
Removing the front panel
Flathead screwdriver
Front panel Main unit
Remove the main unit from
the mounting frame by
loosening the locking screws
1
Fasten the mounting
frame to the wall.
2
Connect wires.
3
Tighten
Screwdriver
Loosen
Drainage hole
Do not block the holes.
Insert a wire from the lower side.
<Back wiring>
<Bottom surface>
<Surface wiring>
Installation height
(center of the unit)
1,500 mm (5')
Wire slot
JO-DA
Loosen the special screw
with the special screwdriver,
and remove the front panel.
1
Fasten the unit to the mounting surface.
*Use board anchors or concrete plugs as needed.
4
Replace face plate and tighten
screw with included special
screwdriver.
5
75 mm
3''
Special
screwdriver
(included)
Loosen
Tighten
Vanda resistant
front panel
Anchor x 4
(Prepare anchors according to the size of the mounting screws.)
(not included)
The unit
Mounting screw × 4
(Screw shaft: Ø4.1)
(Slotted Head: Ø8.2 or less
Height 3.0mm or less)
(not included)
Special
screw
Insert the transparent name plate.
Peel off the protective seals on the plate (both sides).1.
Fill in the name on the transparent name plate.
Be sure to leave 25 mm (1") of white space on the right
end to account for insertion.
2.
Insert the filled-in transparent name plate as below
(indicated with in diagram).
3.
2
ABCDEFG
2 mm (1/8")
25 mm
(1")
Insert transparent
name plate here.
150 mm
5-15/16''
Drainage hole
Do not block the holes.
(The diameter and the depth of the holes on the wall depend on
the anchors suitable for the mounting screws used.)
50 mm
1-31/32''
Connect wires to the unit.
3
70 mm
2-3/4''
110 mm
4-3/8''
180mm
7-3/32''
45 mm
1-25/32''
Vandal resistant front panel with the unit attached
Flush mount back box
(included)
Transparent name plate
Special
screw x 4
(included)
Hexagonal wrench (included)
Tighten
Loosen
Install the flush mount back box in
the wall, and then connect the wires to
the unit with the terminal cover open.
1
Insert the transparent name plate.
*See above JO-DV for details.
2
Fasten the front panel to the back
box with the special screws.
3
JO-DV
English Français Español Nederlands Italiano Deutsch
JO-DVF
7
WIRING
Insert wires securely into each terminal as shown.
Video door station
EnglishFrançaisEspañolNederlandsItalianoDeutsch
JO-DA
JO-DV JO-DVF
A1 A2
2
NP
2
NP
Electric door
strike
EL-12S
Door release
An EL-12S (AC 12 V, 0.125 A, DC 12 V, 0.2 A) or
equivalent part and a separate AC transformer (or
power supply) are required.
Door release contact: AC/DC 24 V, 0.5 A
(Minimum contact: 100 mV DC, 0.1 mA)
(N/O dry closure contact L, L).
*Run separate cables for audio/video and door release.
AC transformer
+
PS18
2
-
PS18
P
Master monitor station
JO-1MD
(To optional units)
(AC/DC 24V, 0.5A N/O dry closure contact)
(Minimum contact: 100mV DC, 0.1mA)
: Power supply
Presence of sound from IER-2
Call tone from door station.
8
Call extension speaker
IER-2
E
1
IER-2
2
NP
PS-1820D
PS-1820
PS-1820S
PS-1820UL
IN 230V~ 50/60Hz
LN
L
N
230V AC
50/60 Hz
Without grounding, the units may not operate
normally.
++
-
-
18V DC 2A
+
-
100V - 240V
50/60 Hz
NOTES:
• To add an expansion monitor station, see the installation
manual of the expansion monitor station.
NP: Non-polarized
P: Polarized
18V DC 2A
OPERATIONS
Answering a door call
Push Call button.
1
The call tone sounds, an image appears on screen.
2
• The screen turns off after approx. 45 seconds if not answered.
Push , and after the beep, communicate hands-free (hands-free mode).
3
After finishing communication, push and communication
4
will end after the beep.
NOTES:
• Communication ends automatically after approx. 1 minute.
• The communication volume can be adjusted during the monitoring or
the communication by pressing
There are three communication volume settings to cycle through:
[] (Minimum), [] (Medium), and [] (Maximum). The current
volume level is displayed on the screen and disappears in approx. 5
seconds. The default setting is [] (Medium).
.
English Français Español Nederlands Italiano Deutsch
For loud outdoor areas, use Press-to-Talk mode (PTT)
After 2 seconds or more
Activating door release
Press and hold for 2 seconds or more.
1
After approx. 2 seconds beep sounds, PTT mode is engaged.
• If
When communicating, keep pressed. To hear the caller’s voice,
2
release .
Status LED lights when you talk, and flashes slowly as you listen to caller
(or hear outside sounds).
NOTES:
• It is not possible to switch back to hands-free mode (from PTT mode
Press .
1
Door release is activated and door can be opened.
2
During release: Status LED lights.
is pressed briefly, PTT mode is not engaged.
during communication).
9
Monitoring door station
EnglishFrançaisEspañolNederlandsItalianoDeutsch
Adjust call tone volume
Push in standby mode.
1
The video image from the door station and the incoming audio is heard.
2
If you do not push , the caller will not hear sounds from the inside
station.
Push to end monitoring.
3
NOTES:
• To talk to door station during monitoring, momentarily push
This allows communication with the door station.
• The monitoring turns off automatically after approx. 1 minute.
Push in standby mode to adjust call tone volume and display the
1
volume level.
.
Push until the desired call tone volume level is heard.
2
NOTES:
• There are four call tone volume settings to cycle through:
] (Mute), [] (Minimum) - [] (Maximum).
[
The current volume level is displayed on the screen and disappears
in approx. 5 seconds. The default setting is [] (Medium).
Night illumination
At night, the door station White light LED lights up during calling or monitoring door station.
<When a call is made from the door station>
If Call button is pushed, the White light LED lights up.
When communication ends, the White light LED will turn off.
<When the white light LED is lit up during monitoring door station>
When
will light up.
When monitoring door station ends, the White light LED will turn off.
is pushed during monitoring door station, the White light LED
♪
♪
10
NOTES:
• The door station evaluates lighting conditions to automatically turn
on the white light LED when necessary.
Adjust screen brightness
Push when the screen is difficult to see. The screen brightness
1
changes from [ 1] (the darkest) to [ 5] (the brightest) during
communication or monitoring.
NOTES:
• The current brightness level is displayed on the screen and
disappears in approx. 5 seconds.
• The default setting is [
3].
Activating/Triggering external devices (if installed)
Press to operate to the unit’s option output.
1
NOTES:
• Optional devices must be installed and connected properly.
The
• While the button is pressed, the N/O dry closure contact signal
is kept being output.
can control lights, secondary doors, garages, etc.
TECHNICAL PRECAUTIONS
Cleaning:
• Clean all units with a soft cloth and gentle cleaner. Do not spray cleaner directly on unit. Do not use an abrasive cleaner or cloth.
• Door stations are weather resistant.
Wiring:
• When a short is detected between A1 and A2 of the door station, the unit stops functioning and the Status LED flashes rapidly until the
short is removed. Check the wires.
• If noise is heard from the master monitor station, the wiring is disconnected between the video door station and the master monitor
station.
Trouble:
• If the station does not respond, reboot this station by pressing the RESET button.
• When the power supply is turned off, power failure, or the RESET button is pressed, the setting of brightness, communication volume,
and call tone volume are returned to the default setting.
English Français Español Nederlands Italiano Deutsch
SPECIFICATIONS
JO-1MD (Master monitor station)
Power supply DC 18V (from power supply)
Current consumption (standby) 24mA (max) 410mA
Communication Hands-free: Auto-voice actuation
PTT: Press-to-talk, release to listen
Ambient temperature 0 - 40°C (+32°F - +104°F)
Monitor 7 inch color LCD screen
Mounting Wall-mount
Electrical box 3-gang box
Material Flame resistant ABS resin
Color White
Dimension 130 (H) x 230 (W) x 21 (D) (mm)
5-1/8 (H) x 9-1/16 (W) x 13/16 (D) (inches)
Weight Approx. 470g (1.04 lbs.)
JO-DA/JO-DV/JO-DVF (Video door station)
Camera unit 1/4 - inch color CMOS
Ambient temperature -20 - 60°C (-4°F - +140°F)
Minimum illumination Approx. 5 lux at 50 cm (1'6'') distance
Dimensions (JO-DA) 129 (H) x 97 (W) x 36 (D) (mm)
5-3/32 (H) x 3-27/32 (W) x 1-13/32 (D) (inches)
(JO-DV) 173 (H) x 98 (W) x 27 (D) (mm)
6-13/16 (H) x 3-7/8 (W) x 1-3/8 (D) (inches)
(JO-DVF) 209 (H) x 135 (W) x exposed area 3.5 (D) (mm)
8-1/4 (H) x 5-5/16 (W) x 5/16 (D) (inches)
(Flush mount back box
for JO-DVF)
Weight (JO-DA) Approx. 200 g (0.44 lbs.)
(JO-DV) Approx. 650 g (1.43 lbs.)
(JO-DVF) Approx. 580 g (1.27 lbs.)
(Flush mount back box
for JO-DVF)
IP rating IP54 (JO-DA / JO-DV / JO-DVF)
IK rating
180 (H) x 110 (W) x 45 (D) (mm)
7-3/32 (H) X 4-3/8 (W) X 1-25/32 (D) (inches)
Approx. 550 g (1.2 lbs.)
IK08 (JO-DV)
IK07 (JO-DVF)
11
MEMO
63
WARRANTY GARANTÍA
Aiphone warrants its products to be free from defects of material and workmanship under normal
use and service for a period of two years after delivery to the ultimate user and will repair free of
charge or replace at no charge, should it become defective upon which examination shall disclose
to be defective and under warranty. Aiphone reserves unto itself the sole right to make the final
decision whether there is a defect in materials and/or workmanship; and whether or not the product
is within the warranty. This warranty shall not apply to any Aiphone product which has been
subject to misuse, neglect, accident, power surge, or to use in violation of instructions furnished,
nor extended to units which have been repaired or altered outside of the factory. This warranty does
not cover batteries or damage caused by batteries used in connection with the unit. This warranty
covers bench repairs only, and any repairs must be made at the shop or place designated in writing
by Aiphone. This warranty is limited to the standard specifications listed in the operation manual.
This warranty does not cover any supplementary function of a third party product that is added
by users or suppliers. Please note that any damage or other issues caused by failure of function
or interconnection with Aiphone products is also not covered by this warranty. Aiphone will not
be responsible for any costs incurred involving on site service calls. Aiphone will not provide
compensation for any loss or damage incurred by the breakdown or malfunction of its products
during use, or for any consequent inconvenience or losses that may result.
The object area of is the EU.
English Español
Aiphone garantiza que sus productos están libres de defectos de material y mano de obra, en uso y
servicio normal, por un período de dos años después de la entrega final al último usuario y reparará
sin costo, o reemplazará sin cargo, si llegara a resultar defectuoso, mediante una inspección que
determine que efectivamente está con defecto y en garantía. Aiphone se reserva para sí la facultad
única de tomar la decisión final para juzgar si existe una falla en materiales y/o mano de obra, y
si el producto está o no cubierto por la garantía. Esta garantía no se aplicará a ningún producto
Aiphone que haya sido sometido a maltrato, negligencia, accidente, sobrecarga de energía o que
haya sido usado de manera diferente a las instrucciones proporcionadas, o bien por las unidades que
hayan sido reparadas o alteradas fuera de fábrica. Esta garantía no cubre baterías o daños causados
por baterías usadas en conjunto con la unidad. La garantía cubre solo las reparaciones efectuadas
en la mesa de trabajo y cualquier reparación debe ser efectuada en el taller o lugar designado por
escrito por Aiphone. Esta garantía se limita a las especificaciones estándar indicadas en el manual
de funcionamiento. Esta garantía no cubre ninguna función adicional de un producto de terceros que
haya sido añadido por los usuarios o proveedores. Tenga en cuenta que los daños u otros problemas
causados por un fallo de funcionamiento o por la interconexión con los productos de Aiphone
tampoco están cubiertos por la garantía. Aiphone no se responsabilizará por costos incurridos en
cualquier llamada de servicio al sitio mismo en que se presente el defecto. Aiphone no indemnizará
por ninguna pérdida o daño en que se incurra debido a la avería o falla de sus productos durante su
uso, ni por ningún inconveniente o pérdida que se produzca como consecuencia.
El área de objeto de
es la UE.
GARANTIE
Aiphone garantit que ses produits ne sont affectés d'aucun défaut de matière ni de fabrication, en
cas d'utilisation normale et de réparations conformes, pendant une période de deux ans après la
livraison à l'utilisateur final, et s'engage à effectuer gratuitement les réparations nécessaires ou à
remplacer l'appareil gratuitement si celui-ci présente un défaut, à la condition que ce défaut soit
bien confirmé lors de l'examen de l'appareil et que l'appareil soit toujours sous garantie. Aiphone se
réserve le droit exclusif de décider s'il existe ou non un défaut de matière et/ou de fabrication et si
l'appareil est ou non couvert par la garantie. Cette garantie ne s'applique pas à tout produit Aiphone
qui a été l'objet d'une utilisation impropre, de négligence, d'un accident, d'une surtension ou qui a
été utilisé en dépit des instructions fournies ; elle ne couvre pas non plus les appareils qui ont été
réparés ou modifiés en dehors de l'usine. Cette garantie ne couvre pas les piles ni les dégâts infligés
par les piles utilisées dans l'appareil. Cette garantie couvre exclusivement les réparations effectuées
en atelier. Toute réparation doit être effectuée à l'atelier ou à l'endroit précisé par écrit par Aiphone.
Cette garantie est limitée aux spécifications standard répertoriées dans le manuel d'utilisation. Cette
garantie ne couvre pas les fonctions supplémentaires d'un produit tiers ajouté par les utilisateurs ou
fournisseurs. Veuillez noter que les dommages ou autres problèmes causés par l'échec de fonction
ou interconnexion avec les produits Aiphone ne sont pas non plus couverts par cette garantie.
Aiphone décline toute responsabilité en cas de frais encourus pour les dépannages sur site. Aiphone
n'indemnisera pas le client en cas de pertes, de dommages ou de désagréments causés par une
panne ou un dysfonctionnement d'un de ses produits lors de l'utilisation, ou pour toute perte ou tout
problème qui peut en résulter.
La zone d'application de
est l'UE.
GARANTIE GARANZIA
Aiphone garantiert, dass seine Produkte frei von Material- oder Verarbeitungsfehlern sind bei
normalem Gebrauch für die Dauer von zwei Jahren nach der Auslieferung an den Endnutzer
und wird kostenlose Reparaturen oder Austausche vornehmen, sollte das Gerät einen Defekt
aufweisen, der nach eingehender Überprüfung innerhalb der Garantie liegt. Aiphone behält sich
das alleinige Recht vor, endgültige Entscheidungen zu treffen, ob ein Defekt am Material und/oder
in der Verarbeitung vorliegt; und ob das Produkt innerhalb der Garantie liegt. Diese Garantie trifft
auf kein Aiphone-Produkt zu, welches Gegenstand von Missbrauch, Fahrlässigkeit, Unfall und
Stromüberladung gewesen ist oder in Verletzung geltender Vorschriften genutzt wurde, und wird
nicht auf Geräte ausgeweitet, die außerhalb des eigenen Werks repariert oder verändert wurden.
Die Garantie deckt keine Batterien oder Schäden, die durch Batterien in Verbindung mit dem
Gerät verursacht wurden, ab. Die Garantie deckt nur Werkstattreparaturen ab und alle Reparaturen
müssen in den von Aiphone schriftlich vorgesehenen Geschäften oder Orten durchgeführt werden.
Die Garantie ist auf die im Betriebshandbuch angegebenen Standardspezifikationen beschränkt.
Die Garantie deckt keinerlei ergänzenden Funktionen von Drittanbieter-Produkten, die vom Nutzer
oder Händler hinzugefügt wurden, ab. Beachten Sie, dass jegliche Schäden oder andere Probleme,
die durch eine Verwendung des Geräts mit anderen Produkten als Aiphone-Produkten entstehen,
nicht von der Garantie abgedeckt sind. Aiphone ist für alle anfallenden Kosten hinsichtlich örtlicher
Service-Anrufe nicht verantwortlich. Aiphone bietet keinerlei Kompensation für jegliche Verluste
oder Schäden, die aufgrund eines Ausfalls oder einer Fehlfunktion seines Produkts verursacht
wurden, noch für etwaige Unannehmlichkeiten oder Verluste.
Das Anwendungsgebiet von
ist die EU.
Français
Deutsch Italiano
WAARBORG
Aiphone waarborgt zijn producten tegen materiaal- en fabricagefouten bij normaal gebruik en
onderhoud gedurende een periode van twee jaar na levering aan de eindgebruiker, en zal het
product kosteloos herstellen of vervangen indien na onderzoek blijkt dat het toestel een defect
heeft dat onder de waarborg valt. Aiphone behoudt zich het recht voor als enige definitief te
bepalen of er al dan niet sprake is van een materiaal- en/of fabricagefout en of het product nog
onder waarborg is. Deze waarborg geldt niet voor ieder Aiphoneproduct dat is blootgesteld aan
verkeerd gebruik, verwaarlozing, een ongeval, stroomstoten, of verkeerde bediening en evenmin
voor toestellen die buiten de fabriek zijn hersteld of aangepast. Deze waarborg geldt niet voor
batterijen of schade veroorzaakt door batterijen die in het toestel zijn uitgebreid. Deze waarborg
dekt uitsluitend werkbankherstellingen en iedere herstelling moet worden uitgevoerd in een
schriftelijk door Aiphone aangewezen winkel of werkplaats. Deze waarborg beperkt zich tot de
standaardspecificaties die in de bedieningshandleiding staan vermeld. Deze waarborg beslaat
geen enkele aanvullende functie van een product van een externe partij dat door gebruikers of
leveranciers wordt toegevoegd. Gelieve op te merken dat schade of andere problemen die het
gevolg zijn van storing bij gebruik of verbinding met producten anders dan die van Aiphone,
eveneens niet door deze waarborg worden gedekt. Kosten die gepaard gaan met herstellingen ter
plaatse kunnen niet worden verhaald op Aiphone. Er kan geen schadeloosstelling van Aiphone
worden geëist voor enig verlies of schade als gevolg van een defect of storing tijdens het gebruik
van zijn producten, of voor enig ongemak of verlies dat hieruit voortvloeit.
Het toepassingsgebied van
Aiphone garantisce che i suoi prodotti sono privi di difetti nei materiali o nella lavorazione, in
condizioni di utilizzo normali e per un periodo di due anni dalla consegna all'utente fi nale. Aiphone
eseguirà la riparazione o la sostituzione gratuita del prodotto qualora tale prodotto risulti difettoso
e la garanzia sia applicabile al difetto rilevato. Aiphone si riserva il diritto esclusivo di stabilire in
via defi nitiva se sono presenti difetti nei materiali e/o nella lavorazione e se il prodotto è coperto
dalla garanzia oppure no. La presente garanzia non è applicabile ad alcun prodotto Aiphone che sia
stato sottoposto ad uso improprio, negligenza, incidente, sovracorrente o che sia stato utilizzato in
violazione alle istruzioni fornite, né può essere estesa alle unità che sono state riparate o manomesse
al di fuori della fabbrica. Questa garanzia non copre le batterie né i danni causati dalle batterie
usate in connessione con l'unità. Questa garanzia copre solo le riparazioni del prodotto consegnato
presso il punto designato. Le eventuali riparazioni devono essere eseguite presso il punto vendita
o il luogo designato per iscritto da Aiphone. Questa garanzia è limitata alle specifi che standard
elencate nel manuale d'uso. Questa garanzia non copre le funzioni supplementari di prodotti di altre
aziende aggiunti dagli utenti o dai fornitori. Eventuali danni o altri problemi causati da problemi
di funzionamento o interconnessione con prodotti Aiphone non sono coperti da questa garanzia.
Aiphone non potrà essere ritenuta responsabile di eventuali costi sostenuti in caso di chiamata per
l'assistenza sul posto. Aiphone non offrirà alcun compenso per gli eventuali danni o perdite subiti
a causa della rottura o del guasto dei suoi prodotti durante l'uso, o per qualsiasi disagio o perdita
conseguente che si dovesse verifi care.
L'area oggetto di
is de EU.
è l'UE.
Nederlands
http://www.aiphone.net/
AIPHONE CO., LTD., NAGOYA, JAPAN
Printed in Thailand
Loading...