Aiphone JK-1HD User Manual

JK-1HD

HANDS FREE COLOR VIDEO INTERCOM

SUB MONITOR STATION

INTERPHONE VIDEO COULEUR MAINS LIBRES

MONITEUR SECONDAIRE

VIDEO INTERCOMUNICADOR A COLOR MANOS LIBRES

MONITOR SECUNDARIO

HANDENVRIJE KLEURENVIDEOFONIE

MONITOR-BIJPOST

VIDEOCITOFONO A COLORI A VIVAVOCE

POSTAZIONE DI MONITORAGGIO SECONDARIA

FK1473 Ⓐ P0109YI

JK-1HD

Sub monitor station

Moniteur secondaire
Monitor secundario
Monitor-bijpost
Postazione di monitoraggio
secondaria

INSTALLATION & OPERATION MANUAL

MANUEL D’INSTALLATION ET D’UTILISATION

MANUAL DE INSTALACIÓN Y OPERACIÓN

INSTALLATIE- EN BEDIENINGSHANDLEIDING

MANUALE D'INSTALLAZIONE E USO

PRECAUTIONS

General Prohibitions Prohibition to Dismantle the Unit Prohibition on Subjecting the Unit to Water General Precautions

WARNING

(Negligence could result in death or serious injury.)

EnglishFrançaisEspañolNederlandsItaliano

1. High voltage is present internally. Do not open the case. Electric shock could
result.

2. Do not dismantle or alter the unit. Fire or electric shock could result.

3. Do not connect a non-specified power source to the +, - terminals. Also, do not
install two power supplies in parallel to a single input. Fire or damage to the unit
could result.

4. Keep the unit away from water or any other liquid. Fire or electric shock could result.

5. Do not put any metal or flammable material into the unit through the openings.
Fire or electric shock could result.

6. Do not use a power supply with a voltage other than the specified voltage. Fire or
electric shock could result.

7. Do not connect any terminal on the unit to an AC power line. Fire or electric shock
could result.

CAUTION

(Negligence could result in injury to people or damage to property.)

1. Do not install or make any wire terminations while power supply is plugged in. It
can cause electrical shock or damage to the unit.

2. Before turning on power, make sure wires are not crossed or shorted. If not, fire or
electric shock could result.

3. When mounting the unit on a wall, install the unit in a convenient location, but not
where it could be jarred or bumped. Injury could result.

4. For power supply, use Aiphone power supply model or model specified for use
with system. If non-specified product is used, fire or malfunction could result.

5. Do not install the unit in any of the following locations. Fire, electric shock, or unit
trouble could result.

* Places under direct sunlight, or near heating equipment that varies in temperature.
* Places subject to dust, oil, chemicals, etc.
* Places subject to moisture and humidity extremes, such as bathroom, cellar,

greenhouse, etc.

* Places where the temperature is quite low, such as inside a

front of air-conditioner.

* Places subject to st eam or smoke (near heating or cooking surfaces).
* Where noise generating devices such as dimmer switches or inverter electrical

appliances are close by.

* Do not install the unit in locations subject to frequent vibration or impact.

6. Do not put anything on the unit or cover the unit with cloth, etc. Fire or unit trouble
could result.

7. Do not press on the LCD or subject it to a high impact. The LCD glass could be
punctured and result in an injury.

8. If the LCD is punctured, do not allow contact with the liquid crystal inside.
Inflammation could result.

* In the event that liquid crystal is ingested, immediately gargle with water and seek

medical attention.

* If contact with the eyes or skin occurs, clean with pure water for at least 15 minutes

and seek medical attention.

refrigerated area or in

1. Keep the unit more than 1 m away from radio or TV set.

General Precautions

2. This unit is for indoor use only. Do not use outdoors.

3. In areas where broadcasting station antennas are close by, the intercom system may be
affected by radio frequency interference.

4. As to other manufacturer's devices (such as sensor, detectors, door releases) used
with this system, comply with the Specifications and Warranty conditions that the
manufacturers or vendors present.

5. Keep th

6. If the unit is down or does not operate properly, unplug the power supply or turn off

7. The unit is for wall-mount use only. For desktop applications, use desk stand.

8. When wall-mounted, the top of the unit may darken. This does not indicate a

9. The unit case may become warm with use, but this is not a unit malfunction.

10. If a cellular phone is used close by, the unit may malfunction.

11. The LCD panel is manufactured with very high precision techniques. Small portions

12

13. At night, due to reduced lighting on the object, the monitor sees more noise and the

14. Talk within 50 cm (20") or less from the unit. If you stand too far away, it may be

15. If there are loud noises around the

16. During communication, if you speak before the other person has finished talking, your

17. At a gate or porch illuminated by fluorescent lamp, the picture may vary, but this is

18. When the outside temperature lowers sharply after rainfall, etc., the inside of the video

19. Due to the environmental sound around the unit, it may hinder smooth communication,

20. The

21. If the screen of a video door station freezes during wintertime, the picture may become

22. This unit is not interchangeable with JA, JF, KB, and KC series units.

23. Warm

e intercom wires at least 30 cm (12") away from AC 100-240 V lines. Noise

and malfunction could result.

the JK-1MED, JK-1MD, and JK-1HD POWER switches.

m

alfunction.

of the panel may fail to light up or some portions may be constantly lit, but this does
not indicate a unit malfunction. Please be aware of this in advance.

. Refrain from using the color monitor station in sunlit areas.

face becomes more difficult to see, but this is not a malfunction.

difficult for the other person to hear the communication.

sound may break up and be difficult to hear.

voice may not be heard. Communication will proceed smoothly if you wait until the
other person has finished before speaking.

no

t a malfunction.

door station may fog up slightly and cause the video image to be blurry, but this is not
a malfunction. Normal operation will be restored when moisture evaporates.

but this is not a malfunction.

outline of video images displayed by video door station may differ from that of

the actual person(s) or background, but this is not a malfunction.

difficult to see or the CALL button may not move, but this is not a malfunction.

-color lighting shining on the door station may change the tint of the picture on

the monitor.

unit (such as music playing or children crying), the

1

PACKAGE CONTENTS

JK-1HD Mounting screws x 2 Wood mounting screws x 2

Installation & Operation manual

- 2 -

2

+ 5 cm

(2")

+ 5 cm

(2")

JK-1HD

2

3

+ 15 cm

(6")

JK-1HD

JK-1MED/1MD

JK-DA
JK-DV

JK-DVF

24

PS18

PS-1820
PS-1810DIN
PS-1820DIN

A

BC

IER-2

(x2)

JK-1MED/1MD JK-1HD

120 120

+

-

A1
A2

B1
B2

L
L

S
S

+

-

SW
SW

B1
B2

INSTALLATION

2-1 Mounting locations

Install the sub monitor station in a place

1

where the screen is not exposed to direct
sunlight.

The sub monitor station has switches on

2

both sides. Allow at least 5 cm (2") of open
space on either side.

2-2 Wiring method, wiring distance

Wire the units from station-to-station (daisy-chained).

Allow at least 15 cm (6") of vertical open

3

space from the center of the mounting
bracket in order to mount the sub monitor
station.

English Français Español Nederlands Italiano

2-3 Cable

Use PVC-coated cable with PE (polyethylene) insulation.

1

Never use individual conductors, twisted pair cable or coaxial cable.

2

Ø

0.65 mm 22 AWGØ 1.0 mm 18 AWG
A 50 m 165' 100 m 330'
B 5 m 16' 10 m 33'
C 75 m 245' 150 m 490'

When using a cable with unused conductors, terminate both ends of

3

the unused pair(s) with a 120 Ω resistor.

- 3 -

3

JK-1HD

1

2

8mm
(3/8")

PS-1810DIN/

PS-1820DIN

PS-1820

MOUNTING

Back wiring

Mounting screws x 2

EnglishFrançaisEspañolNederlandsItaliano

1. Press RELEASE button
(to insert or remove the wire).

2. Insert the cable into the terminal.

Surface wiring

* When a 1-gang box is not mounted, the cable can be surface-run to the top or bottom of

the unit. Cut a cable inlet on the upper part of the unit to allow passage of the wiring into
the unit.

* To pass the cable through the rear

side of the unit, cut out a cable inlet
section.

1-gang box

83.5 mm
(3-5/16")

Mounting bracket

Mounting bracket

Din rail

1-gang box

Wood
mounting
screws x 2

Mounting bracket

83.5 mm
(3-5/16")

83.5 mm
(3-5/16")

- 4 -

4

JK-1MED/1MD

JK-1HD

PS-1820

100V - 240V -

50/60 Hz

230V AC

N
L

18V DC

2 A

PS-1810DIN/

PS-1820DIN

18V DC 1A (PS-1810DIN)
18V DC 2A (PS-1820DIN)

IN 230V~ 50/60Hz

NL

1A

-

+

­+

DC 18 V

-

+

2

P

-

+

2

NP

P

2

NP

2

P

2

P

PS18 PS18

JK-1MED/1MD JK-1HD

2

WIRING

Insert wires securely into each terminal as shown.

Master monitor station

Power supply

Sub master
monitor
station

When the JK-1HD is connected, split
power between the master station and
the sub master station if radio signals
are picked up during communication.

(To optional units)
(AC/DC 24 V, 1.6 A N/O dry closure contact)
(Minimum Contact : 100 mV DC, 0.1 mA)

English Français Español Nederlands Italiano

NP:

Non-polarized

P:

Polarized

- 5 -

5

JK-1HD

EnglishFrançaisEspañolNederlandsItaliano

NAMES

Color LCD video monitor
Microphone

POWER switch

Speaker

Door release LED (red)
DOOR RELEASE button

ZOOM/WIDE button

ADJUST button
PAN/TILT button

CALL button
Option button (*)

Transmit LED (red)

TALK button

OFF button
MONITOR button

(*) The option button controls connected option

Brightness control

（0 〜 10）

Receive volume control

（0 〜 10）

Chime tone volume

（0 〜 10）

units such as turning lighting on and off and
activa

tion of added door releases.

- 6 -

6

OPERATIONS

6-1 Answering a door call (HANDS-FREE mode, PTT mode)

Press CALL button.

1

Instant voice call function

Even without answering, door area can be seen and heard with

2

video and audio (for approximately 45 seconds). Inside sound is
not heard outside.

Chime tone sounds, caller is seen on video monitor, and outside

2

sound is heard.

•

Audio and video turns off after approximately 45 seconds if not answered.

PTT mode

Press and hold TALK button for 1 second or more.A beep

3

Press TALK button momentarily, and after the beep, communicate

3

hands free. Transmit LED (red) lights when you talk, and goes off as
you listen to caller (or hear outside sounds).

sounds, and after approximately 1 second another beep sounds,
PTT mode is engaged. If
than 0.5 seconds), press-to-talk mode is not engaged.

English Français Español Nederlands Italiano

TALK button is pressed briefly (less

After finishing communication, press OFF button and

4

communication will end after the beep.

NOTES: 1.

2. The Transmit LED will light up and go out, but this is not a

1. The screen display switches automatically according to the JK­1MED picture recording settings.

2. Even if the screen display changes, ZOOM/WIDE button
(section 6-5) can be used to change the display.

3. When TALK button is pressed momentarily and communication
starts, the screen display will be held as is regardless of the JK-1
MED picture recording settings.

Communication ends automatically after the times listed below.
・ JK-1MED: Time set at master station (approximately 1 min.,

2 min., 3 min., 5 min.)

・ JK-1MD: Approximately 1 min.

malfunction.

6-2 Activating door release

Press DOOR RELEASE button.

1

When communicating, keep TALK button pressed. To hear

4

the caller's voice, release TALK button.

After finishing communication, pressing OFF button and

5

communication will end after the beep.

NOTES: When press-to-talk mode is disabled by master

monitor station, PTT mode cannot be used.

Open door while the release mechanism is activated. During release:

2

The DOOR RELEASE LED (red) flashes.

- 7 -

6-3 Entrance monitoring

Press MONITOR button in the standby mode.

1

EnglishFrançaisEspañolNederlandsItaliano

The video monitor displays the image from the door station and the

2

incoming audio is heard. If you do not press TALK button, the
caller will not hear sounds from the inside station.

6-4 Room-to-room communication

Press CALL button to talk with the other person.

1

• A call-in is sent to the master monitor station.

• The reply of the other person is not heard.

Or

Press OFF button to end communication.

3

NOTES: 1. To talk to the entrance during entrance monitoring, momentarily

press

TALK button. Press OFF button to end communication.

2. The entrance monitoring turns off automatically after approximately

3. During entrance monitoring, the entrance monitoring time can

4. During entrance monitoring, the initial display uses a wide-angle

5. At night, the Illuminator LED will not light up until

6. If another inside unit attempts to perform entrance monitoring while

Press and release OFF button to end communication.

3

1 minute. To monitor the entrance again, repeat from the beginning.

be extended by approximately 1 min. by pressing
button.

picture.

button is pressed.

one inside unit is already doing so, a warning beep sound will occur.

MONITOR

TALK

If the other person presses TALK button, hands free

2

communication is possible.

6-5 Wide/Zoom switching

Press ZOOM/WIDE button when a picture is displayed.

1

• Switching between wide ⇔ zoom occurs each time the button is
pressed.

NOTES: 1. Room-to-room communication ends automatically after

2. If a call is received from the entrance during room-to-room

NOTES: When the caller is not shown in the center of the picture, the zoom

1. The wide picture may be distorted in comparison with the zoom

2. For a call from the entrance, the picture starts with the zoom

- 8 -

approximately 10 minutes.
To perform room-to-room communication again, repeat from the
beginning.

communication, the image from the entrance is displayed at
the monitor station and sub station where communication

is taking place. Press
room communication, and press

communication with the door station.

[Wide picture] [Zoom picture]

picture can be moved up, down, left, and right. (Refer to section 6-6)

picture due to the characteristics of the door station camera, but
this is not a malfunction.

picture. For entrance monitoring, the picture starts with the wide
picture.

OFF button to end the room-to-

TALK button to switch to

6-6 Pan/tilt operation

When a zoom picture is displayed, press the ［ ］［ ］［ ］ and ［ ］

1

buttons.

• ［

］: Up

• ［ ］: Down

• ［ ］: Left

• ［ ］: Right

• Moving diagonally is also possible.

English Français Español Nederlands Italiano

[Zoom picture]

The image range of the zoom picture and wide picture differs. The

edges of the wide picture do not display with the zoom picture.

6-7 Night illumination

At night, the door station Illuminator LED lights up during
calling or communication.

When a call is made from the door station

6-7-1

If CALL button of door station is pressed

1

The Illuminator
LED lights up.

When communication ends, the illuminator

2

LED will go out.

When the Illuminator LED is lit up during entrance

6-7-2

monitoring

When TALK button is pressed during entrance monitoring,

1

communication starts and the Illuminator LED will light up.

• Inside sound can be heard at the entrance.

Communication starts at this time, so be

aware that inside sound can be heard at
the entrance.

When communication ends, the illuminator LED will go out.

2

NOTES:

Distinguishing between day and night is automatically done by
the door station.

- 9 -

Prrrrrr

6-8 Backlight adjustment, Night sensitivity adjustment

To perform adjustment

Press ADJUST button when the screen is difficult to see.

1

• Automatic adjustment to a more visible screen is performed.

EnglishFrançaisEspañolNederlandsItaliano

<Day> <Night>

[Before adjustment] [Before adjustment]

[After adjustment] [After adjustment]

6-9 If optional units are installed

When a separately-installed sensor detects a malfunction or CALL

1

button is pressed, the alarm sound occurs and the transmit LED (red)
flashes.

To halt adjustment

Press ADJUST button during adjustment.

1

NOTES: 1. Distinguishing between day and night is automatically done by

2. Pressing ADJUST button at night makes the caller's face

1. The ararm sounds aren't interlocked with chime tone volume. The
alarm sounds at a level equivalent to 10 (HIGH) (fixed).

2. The length of the alarm sound varies depending on the
specifications of the connected monitor station.

3. When connecting with JK-1MD, the alarm sound stops after

30 seconds and restoration occurs even if
pressed.

the door station.

easier to see, but moving subjects may be more difficult to see.

OFF button is not

Press OFF button to stop the alarm sound.

2

7

• Operating temperature: 0 C to 40 C (+32 F to +104 F)

• The video image may distort when the door release is activated. But

8

• Power: DC 18 V

• Current consumption: (Max.) 200 mA

• Calling: Chime and image, approximately 45 seconds

• Communication: <HANDS-FREE mode> Hands-free

<PTT mode> Press-to-talk, release to listen:

TECHNICAL PRECAUTIONS

this is not a unit malfunction.

SPECIFICATIONS

Communication time is based on the connected
monitor station.

• Cleaning: Clean the units with a soft cloth dampened with a neutral
household cleanser. Do not use any abrasive cleaner or
cloth.

• If there is a system malfunction, turn the POWER switch at the

monitor station OFF and back ON again. If this does not solve
the problem, unplug the DC power supply and contact a qualified
technician for service.

• Video monitor: 3-1/2" direct view TFT color LCD

• Scanning lines: 525 lines

• Dimensions: 185 (H) x 135 (W) x 27 (D) (mm)

7

• Weight: Approx. 370 g (0.82 lbs.)

-5/16 (H) x 5-5/16 (W) x 1-1/16 (D) (inches)

- 10 -

Warranty

English

Français

Español

Nederlands

Italiano

Aiphone warrants thats its products have no material or workmanship defects under normal use conditions for two years after delivery to the end user. Aiphone will perform repair
or replacement free of charge if the product is defective and the warranty applies to the defect. Aiphone reserves unto itself the sole right to make the final decision whether there is
a defect in materials and/or workman
neglect, accident, or to use in violation of instructions furnished, nor extended to units which have been repaired or altered outside of the factory. This warranty does not cover
batteries or damage caused by batteries used in connection with the unit. This
writing by Aiphone. Aiphone will not be responsible for any costs incurred during on-site service calls. Aiphone will not provide compensation for any loss or damage incurred by
the breakdown or malfunction of its products during use, or for any consequent inconvenience or losses that may result.

ship and whether or not the product is under warranty. This warranty shall not apply to any Aiphone product which has been subject to misuse,

warranty only includes carry-in repairs. Any repairs must be made at the shop or place designated in

The object area of is the EU.

Garantie

Aiphone garantit que ce produit ne présente pas de défaut matériel ou de fabrication dans des conditions normales d'utilisation pendant les deux années suivant la livraison à
l'utilisateur final. Aiphone en effectuera gratuitement la réparation ou le remplacement si le produit est défectueux et que la garantie s'applique pour le défaut. Aiphone se réserve
le droit exclusif de décider s’il existe ou non un défaut de matière ou de fabrication et si l’appareil est ou non couvert par la garantie. Cette garantie ne s’applique pas à tout
produit Aiphone qui a été l’objet d’une utilisation impropre, de négligence, d’un accident ou qui a été utilisé en dépit des instructions fournies; elle ne couvre pas non plus les
appareils qui ont été réparés ou modifiés en dehors de l’usine. Cette garantie ne couvre pas les piles ni les dégâts infligés par les piles utilisées dans l’appareil. Cette garantie
comprend uniquement les réparations en atelier. Toutes les réparations doivent être réalisées à l'atelier ou au site désigné par écrit par Aiphone. Aiphone décline toute responsabilité
en cas de frais encourus pour les dépannages à domicile. Aiphone n’indemnisera pas le client en cas de pertes, de dommages ou de désagréments causés par une panne ou un
dysfonctionnement d’un de ses produits.

La zone d’application de est l’UE.

Garantía

Aiphone garantiza que sus productos no tienen defectos de material ni de mano de obra bajo condiciones de uso normal durante dos años tras su entrega al usuario final. Aiphone
realizará la reparación o cambio libre de costo si el producto está defectuoso y la garantía se aplica al defecto. AIPHONE se reserva el derecho de tomar la decisión final de si hay o
no defectos de material y/o de mano de ob
descuidado, accidentado, o empleado violando las instrucciones suministradas; la garantía tampoco se aplica a unidades que hayan sido reparadas o alteradas por personas fuera de
la fábrica. Esta garantía no cubre las pilas ni los daños causados por pilas utilizada
las reparaciones deben realizarse en el taller o lugar que Aiphone designe por escrito. Aiphone no se responsabilizará de los gastos generados durante llamadas de servicio. Aiphone
no indemnizará por ninguna pérdida o daño en que se incurra debido a la avería o falla de sus productos durante su uso, n
como consecuencia.

ra, y de si el producto está o no cubierto por la garantía. Esta garantía no cubre ningún producto AIPHONE que haya sido mal utilizado,

s asociadas a la unidad. Esta garantía sólo incluye reparaciones acarreadas por el cliente. Todas

i por ningún inconveniente o pérdida que se produzca

El área del objeto es la EU.

Garantie

Aiphone garandeert dat zijn producten onder normale gebruiksomstandigheden gedurende twee jaar na levering aan de eindgebruiker vrij zijn van materiaal- of fabricagefouten.
Aiphone zal het product kosteloos herstellen of vervangen als het defect is en de garantie van toepassing is op het defect. Aiphone behoudt zich het recht voor om als enige
definitief te bepalen of er al dan niet sprake is van
is blootgesteld aan verkeerd gebruik, verwaarlozing, een ongeval of verkeerde bediening en evenmin voor toestellen die buiten de fabriek zijn hersteld of gewijzigd. Deze garantie
geldt niet voor batterijen of schade veroorzaakt door batterijen die in het toestel zijn g
door de klant. Alle herstellingen moeten worden uitgevoerd in de winkel of op de plaats die schriftelijk is aangeduid door Aiphone. Kosten die gepaard gaan met herstellingen ter
plaatse kunnen niet worden verhaald op Aiphone. Er kan geen schadeloosstelling van Aiphone worden geëist voor enig verlies of s
het gebruik van zijn producten, of voor enig ongemak of verlies dat hieruit voortvloeit.

een materiaal- en/of fabricagefout; en of het product nog onder garantie is. Deze garantie geldt niet voor een Aiphone-product dat

ebruikt. Deze garantie geldt uitsluitend voor herstellingen die worden ingeleverd en opgehaald

chade als gevolg van een defect of storing tijdens

Het toepassingsgebied van is de EU.

Garanzia

La Aiphone garantisce che i suoi prodotti saranno privi di difetti nei materiali o nella lavorazione, in condizioni di utilizzo normali, per un periodo di due anni dalla consegna
all’utente finale. La Aiphone eseguirà la riparazione o la sostituzione gratuita del prodotto qualora tale prodotto debba risultare difettoso e la garanzia sia applicabile al difetto
rilevato. La Aiphone si riserva il diritto esclusivo di stabilire in via definitiva se sono presenti difetti nei materiali e/o nella lavorazione e se il prodotto è coperto dalla garanzia
oppure no. La presente garanzia non è applicabile ad alcun prodotto Aiphone che sia stato sottoposto ad uso improprio, negligenza, incidente, o che sia stato utilizzato in violazione
alle istruzioni fornite, né può essere estesa alle unità che sono state riparate o manomesse al di fuori della fabbrica. Questa garanzia non copre le batterie né i danni causati dalle
batterie usate in connessione con l’unità. Questa garanzia copre solo le riparazioni del prodotto consegnato presso il punto designato. Le eventuali riparazioni devono essere eseguite
presso l’officina o il luogo designato per iscritto dalla Aiphone. La Aiphone non potrà essere ritenuta responsabile di eventuali costi sostenuti in caso di chiamata per l’assistenza
sul posto. La Aiphone non offrirà alcun compenso per gli eventuali danni o perdite subiti a causa della rottura o del guasto dei suoi prodotti durante l’uso, o per qualsiasi disagio o
perdita conseguente che si dovesse verificare.

L’area oggetto del è l’UE.

- 47 -

AIPHONE CO., LTD., NAGOYA, JAPAN

AIPHONE CORPORATION, BELLEVUE, WA, USA

AIPHONE S.A.S., LISSES-EVRY, FRANCE

Printed in Thailand

http://www.aiphone.com/

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and
used in accordance with the instructions, may cau
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures: ・Reorient or
from that to which the receiver is connected. Increase the separation between the equipment and receiver. ・Consult the dealer or an experienced radio/TV technician for help.

se harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

relocate the receiving antenna ・Connect the equipment into an outlet on a circuit different