Aiphone JF2HD, JF-2MED User Manual 2

JF-2MED, JF-2HD

HANDS-FREE COLOR VIDEO INTERCOM

INTERPHONE VIDEO COULEUR MAINS LIBRES

HANDENVRIJE KLEURENVIDEOFONIE

FK1260 0108 C

JF-2MED JF-2HD

Master monitor station
Moniteur maître
Monitor-hoofdpost

INSTALLATION & OPERATION MANUAL
MANUEL D’INSTALLATION ET D’UTILISATION
INSTALLATIE- EN BEDIENINGSHANDLEIDING

- 1 -

Sub monitor station
Moniteur secondaire
Monitor-bijpost

PRECAUTIONS

General Prohibitions Prohibition on Subjecting the Unit to Water

Prohibition to Dismantle the Unit

WARNING

(Negligence could result in death or serious injury.)

1. High voltage is present internally. Do not open the case. Electric shock could result.

2. Do not dismantle or alter the unit. Fire or electric shock could result.

EnglishFrançaisNederlands

3. Do not connect any non-specified power source to the +, - terminals, and do not
install two power supplies in parallel to a single input. Fire or damage to the unit
could result.

4. Keep the unit away from water or any other liquid. Fire or electric shock could result.

5. Do not put any metal or flammable material into the unit through the openings. Fire
or electric shock could result.

6. Do not use power supply with a voltage other than specified. Fire or electric shock
could result.

7. Do not connect any terminal on the unit to AC power lines. Fire or electric shock
could result.

CAUTION

(Negligence could result in injury to people or damage to property.)

1. Do not install or make any wire terminations while power supply is plugged in. It
can cause electrical shock or damage to the unit.

2. Before turning on power, make sure wires are not crossed or shorted. If not, fire or
electric shock could result.

3. When mounting the unit on wall, install the unit in a convenient location, but not
where it could be jarred or bumped. Injury could result.

4. For power supply, use Aiphone power supply model specified with system. If non­specified product is used, fire or malfunction could result.

5. Do not install the unit in any of the following locations. Fire, electric shock, or unit
trouble could result.

∗ Places under direct sunlight, or near heating equipment that varies in temperature.
∗ Places subject to dust, oil, chemicals, etc.
∗ Places subject to moisture and humidity extremes, such as bathroom, cellar,

greenhouse, etc.

∗ Places where the temperature is quite low, such as inside a refrigerated area or in

front of air-conditioner.

∗ Places subject to steam or smoke (near heating or cooking surfaces).
∗ Where noise generating devices such as dimmer switches or inverter electrical

appliances are close by.

6. Do not put anything on or cover the unit with cloth, etc. Fire or unit trouble could
result.

7. Do not press on the LCD or subject it to a high impact. The LCD glass could be
punctured and result in an injury.

8. If LCD is punctured, do not allow contact with the liquid crystal inside.
Inflammation could result.

∗ If necessary, gargle your mouth and clean your eyes or skin with clear water for at

least 15 minutes, and consult your doctor.

General Precautions

GENERAL PRECAUTIONS

1. Keep the unit more than 1 m away from radio or TV set.

2. This unit is for indoor use only. Do not use outdoors.

3. In areas where broadcasting station antennas are close by, the intercom system may
be affected by radio frequency interference.

4. As to other manufacturer's devices (such as sensor, detectors, door releases) used
with this system, comply with the Specifications and Warranty conditions that the
manufacturers or venders present.

5. Keep the intercom wires more than 30 cm (12") away from AC 100~240 V lines.
Noise and malfunction could result.

6. If the unit is down or does not operate properly, unplug the power supply or turn off
the JF-2MED and JF-2HD Power switches.

7. The unit is for wall-mount use only. For desktop applications, use desk stand.

8. When wall-mounted, the unit may become dusty. Clean with a soft cloth.

9. The unit case may become a warm with use, but this is not a unit malfunction.

10. If a cellular phone is used close by, the unit may malfunction.

11. If must be noted in advance that the LCD panel, though manufactured with very high
precision techniques, inevitably will have a very small portion of the picture
elements steadily lit or not lit at all, which is not considered a unit malfunction.

12. Refrain from using the color monitor station in sunlit areas.

13. At night, due to reduced lighting on the object, the monitor sees more noise and the
face becomes more difficult to see, but this is not malfunction.

14. Talk within 50 cm (20") or less from the unit. If you stand too far away, it may be
difficult for the other person to hear the communication.

15. If there are loud noises around the unit (such as music playing or children crying),
the sound may break up and be difficult to hear.

16. During communication, if you speak before the other person has finished talking,
your voice may not be heard. Communication will proceed smoothly if you wait
until the other person has finished before speaking.

17. At a gate or porch illuminated by fluorescent lamp, the picture may vary, but this is
not a malfunction.

18. When outside temperature lowers sharply after rainfall, etc., the inside of the camera
may fog up slightly, causing a blurry picture, but this is not a malfunction. Normal
operation will be restored when moisture evaporates.

19. Due to the environmental sound around the unit, it may hinder smooth
communication, but this is not a malfunction.

PACKAGE CONTENTS

1

JF-2MED or JF-2HD

Option connector Release connector (JF-2MED only)

Mounting screws x 2 Wood mounting screws x 2

Installation & Operation manual

- 2 -

INSTALLATION

2

Mounting locations2-1

Install the master monitor station and

1

sub monitor station in places where
the screens are not exposed to direct
sunlight.

The master monitor station and sub

23

monitor station have switches on both
sides.
Allow at least 5 cm (2") of open space on
either side.

JF-2MED / JF-2HD

2

+ 5 cm

(2")

Wiring method, Wiring distance2-2

Wire the units from station-to-station (daisy-chained). Incorrect method

BA

JF-DA

D1

D2

JF-DA
JF-DV

JF-DVF

JF-DA
JF-DV

JF-DVF

JF-D

A
B
C
D

JF-2MED

24 4

2

JF-2HD

CD

PS-1820

PS-1810DIN

Ø 0,65 mm

50 m
50 m

75 m

PS

22AWG

5 m

165'
165'

16'

245'

SP

IER-2

JF-2SD JF-2SD

Ø 1,0 mm

100 m
100 m

10 m

150 m

JF-2HD

18AWG

330'
330'

33'

490'

2

JF-DA

2

Allow 15 cm (6") or more of vertical open space
from the center of the mounting bracket in order
to mount the master monitor station and sub
monitor station.

3

+ 5 cm

(2")

JF-2MED

2

JF-2MED

2

+ 15 cm

4

(6")

4

4

JF-2HD

JF-2SD

8

JF-2HD

JF-2SD

JF-2HD

4

JF-2SD

JF-2HD

JF-2SD

English Français Nederlands

Cable2-3

Parallel or jacketed 2-conductor, mid-capacitance non-

13

shielded cable is recommended. PVC jacket with PE
(polyethylene) insulated conductors is recommended.

(x2)

Never use individual conductors, twisted pair cable or

2

coaxial cable.

When using a cable with unused conductors, terminate both ends of the
unused pair(s) with a 120 Ω resistor.

JF-2MED JF-2HD

A1
A2
A1
A2
B1
B2

S
S

+

-

120 120

B1
B2
B1
B2

+

-

- 3 -

JF-DA
JF-DV

JF-DVF

JF-DA
JF-DV

JF-DVF

JF-D

A1
A2

A1
A2

WIRING

3

Insert wires securely into each terminal as shown.

Video door station

A
I
P

H
O

N
E

J

F

­D

V
F

EnglishFrançaisNederlands

A
IP

H
O

J
F

-D

JF-DA

N
E

A

DOOR 1

A
I
P
H

O
N

E

J
F

­D
V

JF-DVFJF-DV

A1 A2

DOOR 2

A
IP

H
O

N
E

J
F

-D
A

A
I
P

H
O
N

E

J

F

­D

V

JF-DVF JF-DJF-DV

1

F

(Audio only)

A1 A2

E

A
I
P
H

O
N

JF-DA

E

J
F

­D
V

Setting is required. (Refer to section 7-7)

Optional call extension speaker IER-2

OP

IER-2

Door release

Door release EL-9S (AC 12 V, 0.35 A) or
equivalent, requires a separate AC transformer.
Run separate cables for audio/video and door
release.
Door release contact: AC/DC 24 V, 0.5 A
(N/O dry closure contact L, L).

Optional selective door release
adaptor RY-3DL
Use RY-3DL when connecting
door release to 2 locations.

PT

AC Transformer

2

2

2

NP

NP

NP

EL-9S

EL-9S

JF-2MED

Power supply +, - (DC 18 V)

PS-1810DIN

230V AC

IN 230V~ 50/60Hz

­+

18V DC 1 A

OP

RY-3DL JF-2MED

L1
C1

b1

L1

b2
b3

L2

L

C2

D1

L2

PT

D2

E

+

–

NL

1A

-

+

EL-9S

Option connector

Release connector

DC 18V

#2 #1

PS-1820

N

L

100V - 240V -

50/60 Hz

PT

OG(b1)
YE(b2)
GR(E)

BR(L)
RD(L)

+
–

Master monitor station

P

2

-

DC 18 V

18V DC

2 A

+

Release connector

Option connector

Control external devices connected with release connector and
option connector.
[1] Door release output

[2] Options output

[3] Video signal output

2

[1]

NP

PS18

[4] Door release-linked entrance output
[5] Press-to-talk setting input

[6] Foot switch input

[7] External sensor input

(BR)

#1

#2

(RD)
(OG)
(YE)

(BR)
(RD)
(OG)
(YE)
(GR)
(BL)
(PR)
(GY)

(WH)

SW
SW

V +
V ­b1
b2

PK
FS
KS

L
L

E

E

[1]

[2]

[3]

[4]

[7]

Door release

or

RY-3DL

RY-3DL

[5]

[6]

To prevent shorts, be sure to cut unused lead wires
at the bottom and insulate the ends.

Setting is required. (Refer to section 7-8)
(AC/DC 24 V, 0.5 A N/O dry closure contact)
Connect the brown and red wires from the release connector to the
door release (or to the RY-3DL as shown in the wiring diagram).

(AC/DC 24 V, 1.6 A N/O dry closure contact)

(NTSC, 1 Vp-p/75 Ω) Wiring distance: 3 m
NOTES: When video signal is output to the external

equipment, it may be possible to hear the buzz noise
from master station. Consult AIPHONE distributor.

If the blue and white wires are shorted, press-to-talk will not
be operable.

Connect a commercially-available foot switch to the purple
and white wires (N/O dry closure contact).

Setting is required. (Refer to section 7-9)

N/O dry closure contact

Input method

External sensor input

(start signal only detection method)
Detection confirmation time 100 mS or more
Contact resistance

During dry closure: Less than 700 Ω
Terminal short current Less than 10 mA

Vo ltage between terminals

Less than DC 20 V

(when open between terminals)

- 4 -

JF-2HD

Sub monitor station

Option connector

#3

#3 #3

(BR)
(RD)
(OG)
(YE)
(GR)

(BL)
(PR)
(GY)
(WH)

SW
SW

PK
FS

[2]

[6]

E

JF-2HD

[5]

Sub monitor station

To prevent shorts, be sure to cut unused lead wires
at the bottom and insulate the ends.

English Français Nederlands

4

OFF

NP: Non-polarized
P: Polarized

BR: Brown
RD: Red
OG: Orange
YE: Yellow
GR: Green
BL: Blue
PR: Purple
GY: Gray
WH: White

Optional long distance adaptor JBW-BA

Use JBW-BA when the wiring distance between the
video door station and JF-2MED is within the distance
range shown in the table.

1. Use PE (polyethylene) insulated cable.
Do not use PVC.

•Terminal setting (2nd unit)
Setting changes are only required when a 3rd unit is connected.
Put the switch in the ON position, and terminate the furthest sub station.
If the terminal setting is incorrect, the monitor station and sub station will
make a warning sound when they are operated.
Further, the unit may not operate correctly or the video image may distort.

JF-2SD

Sub station Sub station

ON

OFF

SW1

ON

Ye s

Call-in from door station 1

No

SW2

ON

Ye s

No

-

+

1st unit 2nd unit

JF-2MED JF-2HD

ON

123456

SW5

1st unit 2nd unit

JF-2MED JF-2SD

ON

Not used.Call-in from door station 2

JF-DA

A
IP

H
O

N
E

JF

JF-DV

-D
A

JF-DVF

A1
A2

4

-

+

ON

ON

ON side when no 3rd unit is connected

1st unit 2nd unit 3rd unit

JF-2HD

JF-2MED

JF-2HD

OFF

ON

(leave in the factory settings)

OFF side when a 3rd unit is connected

OFF

After changing the setting, be sure to turn the power of the
monitor station on again.

JF-2SD

ON

OFF

SW1

ON

Ye s

Call-in from door station 1

No

SW2

ON

Ye s

No

U
s
e

T
H

E
S

A

p

M
o
w

E

V

e
r

O

s

L

u

T

p

A

p
s

G

t

l

y
a

E

t

A

a

io

s

1

n
's

A

M

.

2

a
s

t
e
r

t
o

D
o
o
r

s
t
a
t
i

o

n
D
C

2
4
V

o
r

1
8
V

t
o
M

a
s
t
e

r
s

+

t
a

(
O

t

i

o

-

b

n

s
e
r
v
e

p
o
l
a

r

i

t

y

)

B
1
B

2

AB

2

NP

1 1

B1

A1

B2

A2

+

-

123456

SW5

1st unit 2nd unit 3rd unit

JF-2MED JF-2SD

OFF

Not used.Call-in from door station 2

2

P

2

JF-2SD

ON

A1
A2

+

-

JF-2MEDJBW-BA

A
B (max.)
C (max.)

Ø 1.0 mm

100~200 m

50 m
50 m

18 AWG
330'~650'

165'
165'

- 5 -

Ø 1.2 mm

100~250 m

50 m
50 m

16 AWG
330'~820'

165'
165'

P

1

PS18

C