Agilent 86100A/B/C Series
Plug-in Modules
Installation Guide
Notices
© Agilent Technologies, Inc. 2000-2005
No part of this manual may be reproduced in any form or by any means
(including electronic storage and
retrieval or translation into a foreign language) without prior agreement and written consent from Agilent Technologies,
Inc. as governed by United States and
international copyright lays.
Manual Part Number
86100-90089
Edition
July 2005
Printed in USA
Agilent Technologies, Inc.
Digital Signal Analysis Division
1400 Fountaingrove Parkway
Santa Rosa, CA 95403, USA
Warranty
The material contained in this document
is provided “as is,” and is subject to being
changed, without notice, in future editions. Further, to the maximum extent
permitted by applicable law, Agilent disclaims all warranties, either express or
implied, with regard to this manual and
any information contained herein, including but not limited to the implied warranties of merchantability and fitness for a
particular purpose. Agilent shall not be
liable for errors or for incidental or consequential damages in connection with the
furnishing, use, or performance of this
document or of any information contained herein. Should Agilent and the
user have a separate written agreement
with warranty terms covering the material in this document that conflict with
these terms, the warranty terms in the
separate agreement shall control.
Technology Licenses
The hardware and/or software described
in this document are furnished under a
license and may be used or copied only in
accordance with the terms of such
license.
Restricted Rights Legend
If software is for use in the performance
of a U.S. Government prime contract or
subcontract, Software is delivered and
licensed as “Commercial computer software” as defined in DFAR 252.227-7014
(June 1995), or as a “commercial item” as
defined in FAR 2.101(a) or as “Restricted
computer software” as defined in FAR
52.227-19 (June 1987) or any equivalent
agency regulation or contract clause. Use,
duplication or disclosure of Software is
subject to Agilent Technologies’ standard
commercial license terms, and non-DOD
Departments and Agencies of the U.S.
Government will receive no greater than
Restricted Rights as defined in FAR
52.227-19(c)(1-2) (June 1987). U.S. Government users will receive no greater
than Limited Rights as defined in FAR
52.227-14 (June 1987) or DFAR 252.2277015 (b)(2) (November 1995), as applicable in any technical data.
Safety Notices
CAUTION
Caution denotes a hazard. It calls attention
to a procedure which, if not correctly performed or adhered to, could result in
damage to or destruction of the product.
Do not proceed beyond a caution sign
until the indicated conditions are fully
understood and met.
WARNING
Warning denotes a hazard. It calls attention
to a procedure which, if not correctly performed or adhered to, could result in
injury or loss of life. Do not proceed
beyond a warning sign until the indicated
conditions are fully understood and met.
Instrument Markings
This product complies with
the WEEE Directive (2002/96/
EC) marking requirements.
The affixed label indicates that
you must not discard this electrical/electronic product in domestic
household waste. Product Category: With
reference to the equipment types in the
WEEE Directive Annex I, this product is
classed as a “Monitoring and Control
instrumentation” product. Do not dispose
in domestic household. To return
unwanted products, contact your local
Agilent office, or refer to www.agilent.com for more information.
2
Installation Instructions
Installation Instructions
This plug-in module is designed for use with the Infiniium DCA Agilent
86100A/B/C wide-bandwidth oscilloscope.
To install the module into the Infiniium DCA
1 Slide the module into an available front-panel slot.
Installation Guide
2 Finger tighten the two knurled screws on the module’s front panel.
Up to two modules can be inserted into the Infiniium DCA. All documentation
(including specifications and regulatory information) for this plug-in module
is located in the Infiniium DCA online help. To access the online help, click
Contents on the Help menu.
3 If ordered, an optional firmware upgrade kit will be enclosed in the module
shipping container. Install this firmware if the manframe does not have the
latest version of firmware. To learn more about firmware upgrades, available
modules, or the Infiniium DCA, visit our website at http://www.agilent.com/
comms/dca.
3
Installation Guide
General Safety Considerations
General Safety Considerations
This product has been designed and tested in accordance with IEC Publication 1010, Safety Requirements for Electronic Measuring Apparatus, and has
been supplied in a safe condition. The instruction documentation contains
information and warnings which must be followed by the user to ensure safe
operation and to maintain the product in a safe condition.
Install the plug-in module according to the enclosure protection provided.
This instrument does not protect against the ingress of water. This instrument
protects against finger access to hazardous parts within the enclosure.
WARNING If this product is not used as specified, the protection provided by the
equipment could be impaired. This product must be used in a normal
condition (in which all means for protection are intact) only.
WARNING No operator serviceable parts inside. Refer servicing to qualified
service personnel. To prevent electrical shock do not remove covers.
WARNING To prevent electrical shock, disconnect the instrument from mains
before cleaning. Use a dry cloth or one slightly dampened with water
to clean the external case parts. Do not attempt to clean internally.
CAUTION This product is designed for use in Installation Category II and Pollution
Degree 2 per IEC 1010 and 664 respectively.
CAUTION Electrical channel input circuits and the trigger input circuit can be damaged
by electrostatic discharge (ESD). Therefore, avoid applying static discharges
to the front-panel input connectors. Prior to connecting any coaxial cable to
the connectors, momentarily short the center and outer conductors of the
cable together. Avoid touching the front-panel input connectors without first
touching the frame of the instrument. Be sure that the instrument is properly
earth-grounded to prevent buildup of static charge. Wear a wrist-strap or heelstrap.
4
Loading...