Agilent Technologies 8510C User Manual
The Agilent Technologies 8510C is a modular
family of compatible products. For flexibility in
specifying a solution that meets your exact needs,
a system is typically ordered as separate line
items. For those who wish ordering convenience,
complete bundled systems are available. Whether
ordering individual components or a bundled system, all 8510C network analyzers include one-year,
on-site service. For systems built from individual
components, installation may be ordered separately. A PC running BASIC Rev 6.3 or higher
under Windows® (3.1/95/NT) is recommended
for installation and service.
Complete systems
Agilent 8510XF family 110 GHz single sweep
systems
(45 MHz to 110 GHz)
The 8510XF family has two models which are
complete single-connection, single-sweep vector
network analyzer systems that offer S-parameter
measurements over an ultra-broadband frequency
in a 1.0 mm coaxial connector. The broadest frequency model covers 45 MHz to 110 GHz. A lower
frequency model is available covering 45 MHz to
85 GHz. Both systems are designed to facilitate
easy connection to wafer probe hardware while
still preserving excellent RF measurement performance. In addition, the system can be used to make
coaxial measurements (to interface to a coaxial fixture or a coaxial DUT) using the same millimeter
head configuration.
Agilent E7340A single-connection single-sweep network
analyzer system (2 to 85 GHz)
The E7340A is a complete system configured with
an 8510C, a 20 GHz and 50 GHz synthesizer, two
85 GHz S-parameter test heads, and a millimeter
test set controller. The instruments are integrated
in the system rack, the system is fully tested, and a
complete system verification is performed prior to
shipment from Agilent. Installation is included at
no additional charge. The E7340A system does not
include calibration kits or test port cable sets.
System components include:
8510C network analyzer
E7342A millimeter subsystem
83621B synthesizer
83651B synthesizer
System rack
Calibration kits and test port cables are not
included and must be ordered separately.
Test set options
• E7340A-STD Standard configuration
• E7340A-005 Add (45 MHz to 2 GHz) low
frequency extension
• E7340A-006 Add RF pass thru (provides coupled
output of 50 GHz source for additional test
set(s). Additional test set(s) must have
Option 001 installed)
• E7340A-056 Low frequency extension and RF
pass through
Features
• 8510C-010 Add time domain
Voltage options
• E7340A-115 110/120 V line voltage operation
• E7340A-230 220/240 V line voltage operation
Extended service options are available.
Agilent 8510C Network Analyzer Family
45 MHz to 110 GHz
Configuration Guide
2
Agilent E7350A single-connection single-sweep network
analyzer system (2 to 110 GHz)
The E7350A is a complete system configured with
an 8510C, a 20 GHz and 50 GHz synthesizer, two
110 GHz S-parameter test heads, and a millimeter
test set controller. The instruments are integrated
in the system rack, the system is fully tested, and a
complete system verification is performed prior to
shipment from Agilent. Installation is included at
no additional charge. The E7350A system does not
include calibration kits or test port cable sets.
System components include:
8510C network analyzer
E7352A millimeter subsystem
83621B synthesizer
83651B synthesizer
System rack
Calibration kits and test port cables are not
included and must be ordered separately.
Test set options
• E7340A-STD Standard configuration
• E7340A-005 Add (45 MHz to 2 GHz) low
frequency extension
• E7340A-006 Add RF pass thru (provides
coupled output of 50 GHz source for additional
test set(s). Additional test set(s) must have
Option 001 installed)
• E7340A-056 Low frequency extension and RF
pass through
Features
• 8510C-010 Add time domain
Voltage options
• E7340A-115 110/120 V line voltage operation
• E7340A-230 220/240 V line voltage operation
Extended service options are available.
Agilent 85107B network analyzer system
(45 MHz to 50 GHz)
The 85107B is a complete system configured with
a 50 GHz synthesizer, 50 GHz S-parameter test set,
and 2.4 mm measurement accessories. The instruments are integrated in the system rack, the system
is fully tested, and a complete system verification
is performed prior to shipment from the factory.
Installation is included at no additional charge.
System components include:
8510C network analyzer
8517B test set with Option 002
(deleted step attenuators and bias tees)
83651B synthesizer
85056A calibration kit
85133F cable set
85043C rack
Test set options
• 85107B-STD Standard configuration
• 85107B-005 Add attenuators and bias network
(not compatible with 85107B-STD)
• 85107B-007 High power and high dynamic
range configuration (requires 85107B-005)
Source options
• 85107B-51B Standard 50 GHz synthesized
sweeper, no front panel
• 85107B-50B 50 GHz synthesized source with
front panel
• 85107B-50L 50 GHz CW synthesized source
with front panel
Features
• 8510C-010 Add time domain
Voltage options
• 85107B-115 110/120 V line voltage operation
• 85107B-230 220/240 V line voltage operation
Accessories
• 85107B-002 2.4mm calibration kit and cables
• 85107B-001 3.5mm calibration kit and cables
• 85107B-E33 Do not include 2.4mm kit and
cables (not compatible with 85107B-002)
Extended service options are available.
3
Agilent 8510SX network analyzer system
(45 MHz to 26.5 GHz)
The 8510SX is a complete system configured with
a 26.5 GHz synthesizer, 26.5 GHz S-parameter test
set, and a complete set of 3.5 mm measurement
accessories. The instruments are integrated in the
system rack, the system is fully tested, and a complete system verification is performed prior to
shipment from the factory. Installation is included
at no additional charge.
System components include:
8510C network analyzer
8515A test set
83631B synthesizer
85043C rack
85052C calibration kit
11752D gauge kit
85131F cable set
Features
• 8510C-010 Add time domain
Voltage options
• 8510SX-115 110/120 V line voltage operation
• 8510SX-230 220/240 V line voltage operation
Accessories
• 8510SX-001 7 mm accessories (85052C and 85132F)
Extended service options are available.
Agilent 8510E network analyzer system
(45 MHz to 20 GHz)
The 8510E is a complete unracked system configured with a 20 GHz synthesizer, 20 GHz S-parameter test set, and 3.5 mm connector accessories.
Installation is not included.
System components include:
8510C network analyzer
8514B test set with Option 002
(deleted step attenuators and bias tees)
83621B synthesizer
85052D calibration kit
85131D cable set
Test set attenuation options
• 8510E-STD Standard configuration
• 8510E-002 Add attenuator and bias network
Features
• 8510C-010 Add time domain
Calibration kit options (select one)
• 8510E-004 3.5mm economy calibration kit
• 8510E-005 3.5mm precision calibration kit
Extended service options are available.
Agilent 85106D millimeter-wave network analyzer
subsystem (33 GHz to 110 GHz)
When combined with the appropriate 85104A
series test set modules (see page 6) and 11644A
series calibration kits, the 85106D provides a
complete system for measurements in the millimeter-wave frequency range. The instruments are
integrated in a 1600 mm system rack. It is fully
tested and a complete system verification is performed prior to shipment from the factory.
Installation is included at no additional charge.
The 85106D system consists of:
8510C network analyzer
85105A test set controller
83621B synthesizer (2 total)
1600 mm rack
Must also order appropriate 85104A series test
set modules and 11644A series calibration kit
for complete system.
Frequency range (select one)
• 85106D-STD 33 - 110 GHz
• 85106D-001 45 MHz - 110 GHz, adds 8517B and
needed accessories
• 85106D-007 45 MHz - 110 GHz, high power/high
dynamic range
Features
• 8510C-010 Add time domain
Voltage options
• 85106D-115 110/120 V line voltage operation
• 85106D-230 220/240 V line voltage operation
Extended service options are available.
4
Agilent 85108A pulsed-RF network analyzer system
(2 GHz to 20 GHz)
Based on an 8510C with Option 008, this system
provides the capability to measure the amplitude
and phase response of a device or component
being driven with a pulsed-RF input signal. The
instruments are integrated in a 1600 mm system
rack. It is fully tested and a complete system verification is performed prior to shipment from the
factory. Installation is included at no additional
charge.
System components include:
8510C network analyzer with Option 008
(pulsed-RF measurement capability)
85110A test set
1600 mm rack
83622B synthesizer with Options 001/004/008
83623L synthesizer with Options 004/008
Calibration kits and test port cables in the
appropriate connector interface are not
included and must be ordered separately.
Frequency range (select one)
• 85108A-STD 2 - 20 GHz
• 85108A-E63 500 MHz - 20 GHz
• 85108A-F61 2 - 50 GHz with front panel connectors
• 85108A-F62 45 MHz - 50 GHz
Features
• 8510C-010 Add time domain
Voltage options
• 85108A-115 110/120 V line voltage operation
• 85108A-230 220/240 V line voltage operation
Extended service options are available.
Agilent 85108L pulsed-RF network analyzer system
(45 MHz to 2 GHz)
Based on an 8510C with Option 008, this system
provides the capability to measure the amplitude
and phase response of a device or component
being driven with a pulsed-RF input signal. The
instruments are integrated in a 1600 mm system
rack, the system is fully tested, and a complete system verification is performed prior to shipment
from the factory. Installation is included at no
additional charge.
System components include:
8510C network analyzer with Option 008
(pulsed-RF measurement capability)
85110L test set
1600 mm rack
83620B synthesizer with Options
001/004/008/H80
83620B synthesizer with Options 004/008/H80
Calibration kits and test port cables in the
appropriate connector interface are not
included and must be ordered separately.
Features
• 8510C-010 Add time domain
Voltage options
• 85108L-115 110/120 V line voltage operation
• 85108L-230 220/240 V line voltage operation
Extended service options are available.
Agilent 85122A high frequency device modeling system
(45 MHz to 20 GHz)
When combined with the 85190 series high
frequency IC-CAP software, along with Cascade
probes or ICM fixtures, the 85122A can be used to
model BJT, FET, MOS, and diode devices. All
instruments are integrated in a 1600 mm system
rack prior to shipment from the factory.
Installation is included at no additional charge.
System components include:
8510C network analyzer
8514B test set
83621B synthesizer
11612A Option K10/K20 force/sense bias networks
4156C DC source/monitor
85131F cable set
1600 mm rack
Probes, fixtures, calibration kits, 85190 series
software, and workstation must be ordered
separately.
• Option 230 provides system cabinet set up for
220/240 V operation
Custom configurations available to meet other
frequency coverage and power requirements.
5
System components
For flexibility in specifying a solution that meets
your exact needs, a system can be ordered as separate line items. A complete system includes the
Agilent 8510C network analyzer, a test set, compatible source, and measurement accessories.
All major system components (network analyzer,
test sets, and sources) include one-year on-site
service.
8510C ATO options
• 8510C-008 Pulsed-RF capability requiring 85110A
or 85110L S-parameter test set
• 8510C-010 Add time domain
Rack flange kits
• 8510C-908 Rack flange kit, front handles detached
• 8510C-913 Rack flange kit, front handles attached
Additional documentation
• 8510C-910 Extra operating and service manual
set
• 8510C-916 Extra operating and programming
manual set
Extended service options are available.
Test sets (Choose one)
• 8514B S-parameter test set (45 MHz to 20 GHz)
With rugged 3.5 mm connector test ports
• 8515A S-parameter test set (45 MHz to 26.5 GHz)
With rugged 3.5 mm connector test ports
• 8517B S-parameter test set (45 MHz to 50 GHz)
With rugged 2.4 mm connector test ports
• 85110A pulsed-RF S-parameter test set (2 to 20 GHz)
For use with 8510C Option 008. Includes rugged
3.5 mm connector test ports and four built-in
step attenuators to independently set power
level to all four downconverter channels.
Requires 8360 series synthesized sources for
complete operation (83622B and 83623L).
• 85110L pulsed-RF S-parameter test set (45 MHz to
2 GHz)
For use with 8510C Option 008. Includes rugged
7 mm connector test ports and four built-in step
attenuators to independently set power level to
all four downconverter channels. Requires two
8360 series synthesized sources for complete
operation (83620B-H80, two each).
• 8511A frequency converter (45 MHz to 26.5 GHz)
3.5 mm connector ports
• 8511B frequency converter (45 MHz to 50 GHz)
2.4 mm connector ports
Note: Agilent 8511A/B require external, customerfurnished couplers, or signal separating devices to
provide complete test set capability. A source with
front panel RF power output may be more suitable
for 8511-based applications.
Test set options
Option Description 8514B 8515A 8517B 85110A 85110L 8511A/B
STD No IF switching X X
001 Add IF switching for multiple test set operation X X X X X X
002 Delete step attenuators and bias tees X X X
003 High forward dynamic range configuration X
(degrades reverse transmission dynamic range)
003 Add attenuators and bias tees X X
999 Standard input power X
004 High power configuration (moves port 2
attenuator in front of b2 sampler) X
004 Add attenuators and bias tees X
027 High source power X
908 Add rack flange kit X X
913 Add rack flange and handles kit X X X X
910 Extra operating and service manual X X X
Loading...