AES Predator-WiFi, Predator Pro 2 Installation Instructions

1 | P a g e

Installation Instructions

For

Predator-WiFi (PRO 2)

PROFESSIONAL INSTALL ONLY

Do NOT give this manual to end user!

Manual Version 1

The manufacturer cannot legally offer technical support to non-qualified gate

or door installers. End users should employ the services of a professional

install company to commission or support this product!

Tip: Site Survey BEFORE you begin. See Page 3!

2 | P a g e

Index

Section

Pages

Site Survey

3

WiFi Setup

4-8

Answering on Android

9

Answering on Apple

10

LAN setup

11

Installation

12

Power

13

Intercom Module Wiring

13

Keypad Module Wiring

14

Output Connections Example

14

Adding Additional APP Users

15

Other Settings

16

Sounds, Volume & Speech

17

Using the APP

18

Keypad Programming

19

Using the Keypad

21

Troubleshooting

21

Revision Changes

23

3 | P a g e

Site Survey

WiFi

Mbs

Slow Fast

YES!

I have some wifi signal at the gate with my
phone! If not, STOP. You will need some form
of wifi extender, or repeater, or LAN/CAT5
cable!

YES!

I have at least 1 Mb UPLOAD speed. If not
STOP! This system may operate intermittently
remotely or have delayed PUSH notifications.

YES!

My wifi Internet Security is WPA or WPA2 or
better.

YES!

My wifi network supports 802.11 b/g or n (2.4g
frequency networks). Note: This device cannot

run on “a” or “s” type networks (these are 5G

frequency).

SSID

1:____
2:____

3:____

YES!

The network I am trying to connect to is a
single network without duplicate SSID
networks of the same name.

4 | P a g e

Wifi Setup

Step 1

Step 2

Step 3

Open the intercom and connect antenna.

Do not install the intercom.
Power it up beside the router so
that you can perform the
configuration with the home
owners phone beside the
intercom and router.

Note: If you skip this step and
proceed directly to installation,
technical support may request
you go back and perform this

Download and install the app
on the end-user’s phone.

Search for wifi PRO 2 and find
the icon, or scan the QR code
if the phone has a QR scan
app.

Tip: Be sure to accept ALL
permissions during install,
otherwise you will experience
problems later!

3-4 feet / 1 metre

Architectural or “Portrait” oriented models
will have security screws at the top.
Loosen only these with the security
screwdriver provided.

Pedestal style “Landscape” orientated

units will have a locking key.

Loosen top screws

Use Key on lock

Portrait wall
mount style

Landscape

Pedestal Style

5 | P a g e

Step 4

Connect 24v DC power with the power supply provided.

Step 5

Step 6a

24v DC PSU

110-250v

mains in

WARNING

Mains electricity to be

wired by qualified

electrician only

+24v

GND

N/O

COM

N/C

Relay1

Relay2

Exit button

RJ45 Ethernet

Ethernet Terminals

CPU &

Transmitter

Code

Button

Press and HOLD the code button for more than 3 seconds. A tone
will be heard.

The intercom will now begin to transmit its own wifi network called
BELL-XXXXXX (where XXXXXX is the 6 numerical digits from the
serial ID number).

>3 seconds

With the user’s phone, search for available wifi networks and connect

to the BELL network.

TIP: Your phone needs to be within range of the intercom to detect
this network.

+ - SPK

6 | P a g e

Step 6b

Step 7a, 7b, 7c

Step 7d, 7e

Wifi passcode

Enter the default pass code 123456789 and the users phone should now
be connected directly to the intercom.

Press CONNECT on android devices and DONE on apple devices.

After pressing
SEARCH, the APP
will now search for
the intercom and
should detect it.

Intercom ID will be auto filled.

Enter “admin” for the main

user.

Enter “123456789” as the

default password and press

the TICK as shown.

7 | P a g e

Step 8

Step 9a, 9b, 9c, 9d

Note: The intercom and phone are directly connected in a point to point link. Although we know
the intercom is fully operational, we now need to connect it to the local wifi network.

The intercom is now searching the area for wifi networks and will display all compatible networks
on the App screen.

Press the Video icon to
view live video.
Note: at close proximity,
you will experience acoustic
feedback. This is normal.

TIP: If you can view live
video, and hear acoustics,
then this proves that the
intercom hardware is

working as it should.

Should be showing

ONLINE status.

8 | P a g e

Step 9e, 9f, 9g

Step 10

Diagnostic Tips

1. Intercom is showing online status, but the video feed shows “fetching”.

A. This can be caused by poor power cable extended to the intercom, weak wifi, or too many
devices connected to the wifi network and the router is incapable of managing the workload.

2. Intercom is not showing online status.

A. This can be caused by incorrect wifi password created, or wifi dropping in and out due to weak
signal.

3. I can see video but there is no audio on the phone or there is no audio at the intercom.

A: This can be caused by the audio settings being too low on the phone, or permissions for the
app were not accepted during app install. Check microphone permissions for the app in the phone
settings.

4. The status is showing online, then connecting, then online again.

A: This is normal when a phone roams between two wifi connections, or between wifi and data.
Make sure the phone is stationary and either has good wifi or a stable data connection.

Enter the WIFI PASSCODE for the
network which you are connecting to.

WARNING: Take care not to enter a
typing mistake. The intercom will accept
any wifi password and will not know if it
is correct or not!

Wifi Signal strength must be at least

25%, or you will have problems!

Wait 60 seconds.
The intercom will now
re-boot and attempt to
connect to the wifi
network with the
password you have
entered.

60 secs..

If you can see live
video and hear audio,
the intercom has
successfully
connected to the
network.

If for some reason this
does not work, try
connecting to the wifi
network again and
double check the wifi
password is correct.