AEM 30-4401 Digital Oil Fuel Pressure Gauge User Manual

30-4401 FLUID PRESSURE GAUGE QUICK START GUIDE

DIGITAL DISPLAY GAUGE

The AEM Digital Display Gauges are designed for easy installation and usability. The 30-4401 Fluid Pressure Gauge kit
comes with all the necessary components to install and use the gauge. Follow the instructions printed in this quick start
sheet to install your gauge and start using it as soon as possible. Visit the “AEM Gauges” section of the AEM electronics
forum for more information on the advanced features of this gauge. The forums can be accessed by clicking on the
“FORUMS” link on the AEM home page, www.aempower.com.

Gauge Configuration: The gauge bezels are threaded on to the
gauge cup. Rotate the bezel in a counter-clockwise direction to
remove it from the cup. Once removed, the faceplate can be
changed and/or a different bezel can be installed.

Electrical Connection: In order to use the gauge, only the red and
black wires need to be connected. The white and blue wires do not
need to be connected. Connect the red wire to switched +12V.
Connect the black wire to a known good ground. Plug the connector
on the harness into the mating connector on the sensor. See the
connection diagram below.

Sensor Installation: The AEM pressure sensor has 1/8”NPT external threads. Install the sensor into a bung with mating
threads.

Troubleshooting: The gauge may show readings of a number greater than “0” or “---“ if the gauge is powered up shortly
after inserting the sensor connector. This is due to temporary pressure buildup in the connector cavity when the connector
is inserted. The connection between the harness and sensor is water resistant, yet non-hermetic, allowing pressure to
bleed off. Due to normal manufacturing variances, bleed-off times will vary, but are usually less than 5 minutes after the
connector has been inserted.

The 30-4401 Kit Contains:

(1) Pressure Gauge assembly
(1) Pressure Sensor
(1) Pressure Cable
(4) Butt Connector
(1) Silver Bezel
(1) White Oil Pressure Faceplate
(1) Black Fuel Pressure Faceplate
(1) White Fuel Pressure Faceplate
(1) Instructions

Pressure Sender

Ground (Black)

Switched +12V (Red)

RS232 (Blue)

0-5V Output (White)

Advanced Engine Management, 2205 126

Figure 1. Connection Diagram

This product is legal in California for racing vehicles only and should never be used on public highways.

Instruction Part Number: 10-4401, © 2006 Advanced Engine Management, Inc.

ADVANCED ENGINE MANAGEMENT INC.

th

Street Unit A Hawthorne, CA. 90250, Phone: [phone] Fax: [phone]

AEM Electronics Warranty

Advanced Engine Management Inc. warrants to the consumer that all AEM Electronics products will
be free from defects in material and workmanship for a period of twelve months from date of the
original purchase. Products that fail within this 12-month warranty period will be repaired or replaced
when determined by AEM that the product failed due to defects in material or workmanship. This
warranty is limited to the repair or replacement of the AEM part. In no event shall this warranty
exceed the original purchase price of the AEM part nor shall AEM be responsible for special,
incidental or consequential damages or cost incurred due to the failure of this product. Warranty
claims to AEM must be transportation prepaid and accompanied with dated proof of purchase. This
warranty applies only to the original purchaser of product and is non-transferable. All implied
warranties shall be limited in duration to the said 12-month warranty period. Improper use or
installation, accident, abuse, unauthorized repairs or alterations voids this warranty. AEM disclaims
any liability for consequential damages due to breach of any written or implied warranty on all
products manufactured by AEM. Warranty returns will only be accepted by AEM when accompanied
by a valid Return Merchandise Authorization (RMA) number. Product must be received by AEM
within 30 days of the date the RMA is issued.

Please note that before AEM can issue an RMA for any electronic product, it is first necessary for the
installer or end user to contact the tech line at 1-800-423-0046 to discuss the problem. Most issues
can be resolved over the phone. Under no circumstances should a system be returned or a RMA
requested before the above process transpires.

AEM will not be responsible for electronic products that are installed incorrectly, installed in a non
approved application, misused, or tampered with.

Any AEM electronics product can be returned for repair if it is out of the warranty period. There is a
minimum charge of $50.00 for inspection and diagnosis of AEM electronic parts. Parts used in the
repair of AEM electronic components will be extra. AEM will provide an estimate of repairs and
receive written or electronic authorization before repairs are made to the product.