Page 1
Upright Vacuum Clean er
2 - 4
IMPORTANT INFORMATION
Owner’s Guide
Household Type
Z5750 Series
4
5 - 6
7 - 8
8 - 9
10
11
12
GUARANTEE
QUICK REFERENCE
HOW TO ASSEMBLE
HOW TO USE
ROUTINE MAINTENANCE
Dust Cup
Dust Cup Filter
Side Door Filters
PERIODIC MAINTENANCE
IMPORTANT
For any advice
on your cleaner and
to order fi lters and
accessories,
please telephone the
Electrolux Helpline on
08706 055055
13
13
14
14
15
Brush Roll
Brush Roll Belt
PROBLEM SOLVING
Mini Turbo Nozzle
Clear Hose
Guide
www.electrolux.co.uk
Page 2
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be followed, in clud ing the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.
WARNING
To reduce the risk of fi re, electric shock, or injury:
• Do not use outdoors or on wet surfaces.
• Do not leave vacuum cleaner when plugged in.
Turn off the switch and unplug the electrical cord
when not in use and before servicing.
• Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
• Use only as described in this manual. Use only
manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If vacuum
cleaner is not working as it should, has been
dropped, damaged, left outdoors, or dropped into
water, have unit serviced before using.
• Do not pull or carry by cord, use cord as a handle,
close a door on cord, or pull cord around sharp edges
or corners. Do not run vacuum cleaner over cord.
Keep cord away from heated surfaces.
• Do not use extension cords or outlets with inadequate
current carrying capacity.
• Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp
the plug, not the cord.
• Do not handle plug or vacuum cleaner with wet
hands.
• Do not put any object into openings. Do not use with any
opening blocked; keep free of dust, lint, hair, and anything
that may reduce airfl ow.
• This vacuum cleaner creates suction and contains a
revolving brush roll. Keep hair, loose clothing, fi ngers, and
all parts of body away from openings and moving parts.
• Do not place cleaner on furniture or stairs as the brush
roll may cause damage. Place cleaner on fl oor with the
handle in storage position while using attachments.
• Do not pick up anything that is burning or smoking, such
as cigarettes, matches, or hot ashes.
• Do not use without dust cup in place.
• Belt pulleys can become hot during normal use. To prevent
burns, avoid touching the belt pulley when servicing the
drive belt.
• Use extra care when cleaning on stairs.
• Do not use to pick up fl ammable or combustible liquids
such as gasoline, or use in areas where they may be
present.
• Store your cleaner indoors in a cool, dry area.
• Keep your work area well lighted.
• Unplug electrical appliances before vacuuming them.
PLEASE SAVE THESE INSTRUCTIONS
WARNING
The brush in the cleaning head rotates at high speed and can cause damage to the mains supply cable if the cleaner passes
over it during cleaning operations.
Care should be taken to ensure that this does not happen. If the cleaning head has accidentally passed over the mains supply cable
the following action should be taken:
1. Switch off and remove the plug from the socket outlet.
2. Examine the mains supply cable for damage (only after removing the plug from the socket outlet).
3. If there is any sign of damage to the supply cable it MUST be renewed. The repair MUST be carried out by an Electrolux Service
Agent or a similar qualifi ed person.
4. NEVER use the machine with a damaged mains supply cable.
Proprietary carpet conditioning and air freshening ma te ri als
After using proprietary carpet conditioning powders, it is recommended that the fi lters be changed. Some of these preparations contain
sub stanc es which if left in the vacuum cleaner for extended periods could damage the plastic mouldings which form the structure of
the cleaner.
Many air fresheners, household deodorants, sprays and polishes contain a highly fl am ma ble gas propellant.
Because of this, it is particularly important that these products are used strictly in ac cord ance with the relevant manufacturer’s
instructions.
It is essential that none of the above products are sprayed directly into the vacuum cleaner or any of its fi lters, hose assembly, or dust cup.
Thermal Cut Off
This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the cleaner switches off, push the
switch pedal once and unplug the cleaner. Check the cleaner for a possible source of overheating such as a full dust cup, a blocked hose or
clogged fi lter. If these conditions are found, fi x them and wait at least 60 minutes before attempting to use the cleaner. After the 60 minute
period, plug the cleaner back in and push the on/off switch On (I). If the cleaner still does not run, please call Electrolux Customer Care on
08706 055 055.
2
Page 3
BEFORE YOU START
CHECK THE VOLTAGE
Before connecting the cleaner to an electrical supply, ensure that the voltage shown on the rating plate located beneath the
cleaner is of the correct voltage for your electricity supply. If it is not, do not use the cleaner but refer back to your dealer.
CONNECTING TO YOUR ELEC TRIC I TY SUPPLY
Permanently connected to the clean er is a mains supply (2-core) cable fi tted with a non-rewirable plug incorporating a 13A
fuse.
In the event of the fuse requiring replacement the fuse cover should be re moved using a small screw driv er. The old fuse MUST
be re placed by a 13A ASTA ap proved BS1362 fuse or a BSI approved fuse. The cover must be re placed before the plug is used
again. In the event of loss of the fuse cover, re place ments can be obtained from your Electrolux Retailers and must be of the
same colour as indicated by the col oured insert on the base of the plug.
If diffi culty is ex pe ri enced in ob tain ing a replacement, con tact Electrolux Customer Services on 08706 055055.
In no circumstances must the plug be used without a correct fuse cover fi tted.
If the plug that is fi tted to your appliance is not suitable for your socket outlet, it must be cut off and the appropriate plug fi tted.
Remove the fuse from the cut off plug.
The cut off plug should then be dis posed of to prevent the hazard of shocks in case it should be plugged into a 13 amp socket
in another part of your home.
The wires in the mains cable of this appliance are coloured in ac cord ance with the following code: Blue: Neu tral. Brown:
Live.
As the colours of the wires in the mains cable of this appliance may not correspond with the col oured markings iden ti fy ing the
terminals in your plug, proceed as follows:
The wire which is coloured blue must be con nect ed to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be con nect ed to the terminal which is marked with the letter L or coloured red.
If using a three-pin plug, do not make any con nec tion to the terminal marked with the letter E or by the earth symbol or col oured green
or green-and-yellow. This cleaner is dou ble in su lat ed and no earth con nec tion is nec es sary.
It is in your interest to ensure that the plug is correctly attached to the mains cable. In case of doubt, consult a qualifi ed elec tri cian, as
Electrolux cannot regard the repair of faults on the plug connection as a service that can be given free of charge under the terms of
the guarantee.
Fuse
13 Amp Fuse
Cover
13 Amp
Fuse
Blue
Brown
Cord
Clamp
The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city offi ce, your household waste disposal service or the shop
where you purchased the product.
3
Page 4
IMPORTANT INFORMATION
Should you require service on your Electrolux cleaner, please telephone Electrolux Customer Services on 08706 055055.
Before requesting service, please check whether your problem is covered under Service Checklist (see below).
New fi lter pads,brush rollers and drive belts can be obtained from Electrolux Retailers. If diffi culty is experienced in obtaining
spares, please contact Electrolux on 08706 055055.
SERVICE CHECKLIST
SERVICE
• If your cleaner will not operate, check the plug connection, plug fuse and mains fuse.
• Never allow the dust cup to become so full that it impedes the air-fl ow, thus reducing the cleaning effi ciency of the machine.
The character of household dust and its effect on the air-fl ow through the machine may vary considerably. Fluffy dust allows
air to pass through readily whereas fi ne powdery dust or proprietary cleaning powders, pack tightly in the dust cup, offering
greater resistance to air-fl ow and will reduce cleaning effi ciency if the cup becomes overloaded.
• Always store your cleaner and spare dust fi lters in a dry place.
• Renew the fi lter pads three or four times a year. This is essential to ensure continued high fi ltration of dust particles.
• Sucking up such items as stockings, clippings of cloth, sizeable pieces of paper, wrappings from cigarette packets or sweets
etc., may block the hose. Electrolux regrets that the clearing of blocked hoses cannot be regarded as service that can
be given free of charge, under the guarantee. Should a blockage occur, fi rst disconnect the cleaner from the electricity
supply, refer to section headed “Block ag es”. If these op er a tions are not suc cess ful, contact Electrolux on 08706 055055.
• Never pick up hot cinders or lighted cigarette ends.
• Make certain that your cleaner does not come into contact with water or any other liquid. It is not designed as a
wet pick up cleaner, and must never be used on damp carpets or wet fl oors.
Important - in the event of the mains supply cable of this vacuum cleaner requiring replacement, we recommend that this be
carried out by Electrolux Service Staff.
Spares
New fi lters, brush rollers and drive belts can be obtained from Authorised Electrolux Dealers and electrical retailers. If diffi culty is experienced
in obtaining spares please call us on 08706 055055 or visit our website at www.shop.electrolux.co.uk
GUARANTEE
This guarantee is in addition to your statutory and other legal rights.
This product is for household use only.
Electrolux products are carefully designed, manufactured, tested and inspected and, in consequence, we undertake to replace or repair
any part found to be defective in materials or workmanship, within one year of delivery to the original purchaser, free of charge. You may
be required to take the product to your nearest service provider if the product requires attention during the fi rst year.
There are certain conditions which may invalidate this guarantee:
a. It is dependent upon the appliance being correctly installed and used in accordance with the Company’s instructions under normal
domestic conditions within the United Kingdom or the Republic of Ireland.
b. Service at all times must be carried out by an Electrolux Service Representative or authorised agent.
c. The guarantee may be invalidated by unauthorised repair or modifi cation of the appliance.
d. You may be charged by Electrolux if you call for an engineer to resolve a problem that we believe is covered in the instruction booklet.
(example: blocked/dirty fi lters)
Electrolux does not accept liability for all defects arising from neglect, misuse or accident. This guarantee excludes such normal wearing
parts as drive belts, brushes and fi lters as the life of these depends upon the amount and nature of use.
Proof of purchase will be required before service under guarantee is provided. Please call 08706 055 055 for assistance.
IMPORTANT:
For future reference we suggest you record the following details here, and keep the receipt with the handbook as proof of purchase.
Purchased from ____________________________________________________
Date purchased __________________Model no __________________________
101 Oakley Road, LUTON, BEDFORDSHIRE, LU4 9QQ
Features of the Electrolux vacuum cleaner and ac ces so ries supplied with it are pro tect ed in Great Britain and abroad by Patents or Registered
Designs.
This appliance conforms with the requirements of the amend ed E.E.C. directive No. 89/336/EEC re lat ing to elec tro mag net ic compatibility
(EMC) CE.
Electrolux, may introduce modifi cations to their product from time to time, and con se quent ly the details given in this booklet are subject to
alteration without notice.
4
Page 5
1
2
3
ON/OFF Switch. International symbol I means On, International
1
symbol O means Off.
Cord Retainer. To use, push electrical cord down into cord
2
retainer.
Dust Cup Latch. Pull up on latch to remove dust cup giving
3
access to the dust cup fi lter and motor fi lter.
Filter Door Latch. Push down on latch and pivot out for access
4
to the fi lter compartment. Push up on latch to close door.
Dust Cup Filter. Clean the dust cup fi lter frequently to maintain
5
good performance.
Dust Cup. The debris from cleaning is collected in the
6
dust cup.
Handle Release. Step on handle release to pull handle
7
back to a comfortable operating position.
QUICK REFERENCE
8
4
5
6
Stair Handle. To use when cleaning stairs.
8
Cleaner Height Setting. An adjustment that raises
9
or lowers the cleaner base to match the type of fl oor
surface.
WARNING: Avoid injury. Keep loose clothing, hair, fi ngers,
and all other parts of body away from any
moving part (such as the revolving brush). Turn
off the switch and unplug the cleaner before
changing the cleaner height setting.
cleaner.
9
7
WARNING: Keep children away from rotating parts on
X
X
X
X
X
5
Page 6
10
11
QUICK REFERENCE
13
Hose Retainers (4). Place hose in retainers to store hose on
10
unit.
Electrical Cord Hooks (2). Wrap electrical cord around them
11
to store electrical cord on unit. The upper cord hook rotates for
quick cord release.
12
Extension Tube Storage. The crevice nozzle stores inside the
larger extension wand.
Carrying Handle. Use this handle to carry unit from one place
13
to another.
Dusting/Upholstery Brush Storage. Store the dusting brush
14
on back of cleaner.
NOTE: WHEN UNIT IS RUNNING, DO NOT
AT TEMPT TO RE MOVE ANY OBJECT
WHICH PRE VENTS THE BRUSH ROLL
FROM TURN ING.
10
10
11
10
12
14
12
First, turn off unit, unplug from the electrical
socket, then re move object from brush roll area.
Ex: sock, rug, etc.
Thermal Cut Off
This cleaner has a special thermostat that protects the cleaner
in case of motor overheating. If the cleaner suddenly turns off,
follow this procedure:
1. Push rocker switch to off (O) position.
2. Unplug the cleaner.
3. Check for source of overheating problem (i.e. full dust cup, blocked
hose, or clogged fi lter).
4. If a full dust cup, blocked hose or clogged fi lter is found, empty
the cup, clear the hose or replace or clean the fi lters.
5. Wait at least 30 minutes before attempting to reuse the cleaner.
6. After 30 minute cool down period, plug the cleaner in and push the
rocker switch to the on (I) position. The cleaner should turn on.
7. If the cleaner still does not operate, call Electrolux on 08706
055055 for assistance.
Helpful Information:
Listen to your cleaner. If you no tice a change in the sound of the motor or a change in
performance, it could simply indicate a com mon usage or maintenance issue. Such as, a need
to raise or lower the carpet height adjustment, possible blockage in hose or brush roll area,
dirty fi lters or a broken or loose brush roll belt. These are all easy to fi x and the instructions
are included in this owner’s guide. Becoming familiar with the in for ma tion in this guide will help
you to get the best possible performance from your new cleaner for many years to come.
CAUTION: Assemble the cleaner before using.
CAUTION: Moving parts, make sure on/off switch is in off (0) position before plugging in.
6
Page 7
Attach Handle
CAUTION: On models with looped handle, use
2
special care. Do not pinch electrical
cord between handle and cleaner.
Electrical
Cord
1
Grooves
Attach Hose
3
Upper
Hose
Retainer
1
From rear of cleaner, align handle with groove and slide
onto cleaner. If necessary, use thumb and fi nger pressure
to slide handle into position.
2
Attach handle with two 1 inch screws provided in the
assembly packet. Use a Phillips® head screwdriver.
NOTE: Hand tighten with screwdriver to be sure both
screws are fi rmly seated.
Models Equipped with Spin Duster
Install Spin Duster
• Fit the Duster to hose retainer so cup is forward and next to
the vacuum dust cup.
• Tighten screw to secure.
• Push end of hose into opening on top of Duster.
4
Hose
Lower
Hose
Retainer
3
Pick up hose and lay across upper hose
retainer.
4
Push the end of the hose in the lower hose
retainer to secure.
Hose
Screw
Hose Retainer
HOW TO ASSEMBLE
SIDE OF CLEANER
7
Page 8
Store Hose and Accessories
Nested
Extension
Tubes
Dusting
Brush
HOW TO ASSEMBLE
Store Electrical Cord
5
Cord Retainer
6
Cord Hook
6
Cord Hook
HOW TO USE
You will fi nd your cord retainer on the handle above the
5
upper cord hook. Firmly push the electrical cord down into
the cord retainer. This will place the cord out of the way
the next time you vacuum.
Next wind the cord around the two cord hooks on the back
6
side of cleaner.
Cleaner Height Setting. An
adjustment that raises or lowers
the cleaner base to match the
type of floor surface. With the
cleaner cord unplugged, set the
adjustment to lowest setting for
maximum carpet cleaning. If the
cleaner is diffi cult to push, move adjustment to next highest setting until cleaner is
comfortable to push. The brush roll must reach the carpet for effective cleaning. For ease
in moving the adjustment knob, place handle in operating position and tilt cleaner back to
remove weight from front wheels.
Handle Release. Step
on handle release to
pull handle back to a
comfortable operating
position. To lower
handle completely
to the fl oor, depress
handle release a
second time.
WARNING: Avoid injury. Keep loose clothing, hair,
fi ngers, and all other parts of body
away from any moving part (such
as the revolving brush). Turn off the
switch and unplug the cleaner before
changing the cleaner height setting.
Store
Helpful Information:
Operate
Before cleaning under low
furniture, check area first
for objects that might harm
the unit or block the vacuum
hose.
Clean
8
Under
Page 9
Models Equipped with Spin Duster
How To Use
• Turn on vacuum, leaving cleaner in the upright (parked) position.
• Depress and hold lever to divert air suction into Duster.
• Allow Duster to spin for 10-15 seconds prior to fi rst use. This action creates
a static charge on the duster and also cleans it after each use.
• Release lever and turn off vacuum.
Clean
• Pull up on Duster handle to unsnap; remove from cup.
• After use, return Duster to cup. Push down to secure.
• Repeat “How to Use” steps above to clean Duster and reactivate static
charge.
NOTE: To use accessory hose, remove from Duster by pulling up
with a slight twisting motion.
NOTE: If Duster will not spin, check and clean dust cup fi lter.
Also, check Duster to see if Duster is bent and straighten
if necessary.
CAUTION: While dusting, turn off vacuum cleaner. Never leave
vacuum running unattended.
NOTE: When using accessories, always ensure
cleaner is in the upright parked position,
do not place cleaner on furniture or steps
as the brush roll may cause damage. Place
cleaner on fl oor with the handle in storage
position.
1. To use accessories remove hose from rear of
cleaner by lifting up and twisting.
2. Place desired accessory onto end of hose or
wand.
Dusting/
Upholstery
Crevice
Nozzle
Hose or
Extension
Tube
Brush
Turbo Nozzle
(On some models)
Dusting/Upholstery Brush is for furniture, blinds,
books, lamp shades, shelves, curtains, draperies, cushions
and fabrics.
Crevice Nozzle cleans corners, stairs, skirting boards,
and between cushions.
Turbo Nozzle (On some models) cleans upholstery
and stairs.
Nested extension tubes to add reach.
HOW TO USE
• Grasp both tubes near ridges.
• Pull apart.
• Turn ridge end to center. • Push tubes together.
9
Page 10
The instructions in this booklet serve as a guide to routine maintenance. To avoid unnecessary service calls, check the dust
cup, fi lters, belt, and brush roll often. We suggest emptying the dust cup after every use.
NOTE: When vacuuming carpet fresheners or cleaners, powder, plaster dust, or similar fi ne substances, the
dust cup and fi lters will require more frequent maintenance.
ROUTINE MAINTENANCE
NOTE: Turn off the switch and unplug the electrical cord before changing the fi lter. Never operate the vacuum
cleaner without the dust cup or fi lter assembly in place.
Emptying the Dust Cup:
Remove dust cup by pulling latch upward and
pivoting dust cup out and away from cleaner.
Dust Cup
Lift fi lter up and out of dust cup with a twist ing
3
motion.
21
Grasp dust cup lid and twist anti-clockwise
to remove.
Empty debris into a waste container.
4
Reinstalling the Dust Cup:
1
Replace fi lter onto centre tube in dust cup applying gentle pressure.
2
Line up tabs on dust cup with openings on lid, rotate
lid clockwise while applying pressure to secure. The
lock symbol ( ) on lid will be centered over dust
cup handle when properly assembled.
3
To replace dust cup, position dust cup with handle
facing inside the dust cup compartment; place bottom of dust cup in bottom
of compartment and rotate upward, pushing dust cup against cleaner until
it locks into place.
Dust cup will not properly seat if the fi lter is not present.
4
10
Tab
3
Tab
Page 11
Instructions to Clean or Change Dust Cup Filter, Code EF83
Check and clean the dust cup fi lter frequently to maintain good performance; at least once
every month.
Remove dust cup by
pulling latch upward
and pivoting dust cup
out and away from
cleaner.
ROUTINE MAINTENANCE
Grasp dust cup lid and
twist anti-clockwise to
re move.
To clean the Filter, Dust Cup and
Dust Cup Lid:
To remove debris, tap fi lter against waste
1
container and/or brush with dusting brush
accessory tool. You may also vacuum the
fi lter using a different cleaner.
If filter needs further cleaning, wash in
2
warm water using a mild detergent. To clean
between fi lter pleats, fan open under running
water.
If dust cup needs cleaning, wash in warm
3
water us ing a mild de ter gent. Do not
sub merge dust cup lid, wipe only with a
damp cloth.
4
When all parts are completely dry, re place
fi lter in dust cup and replace lid.
Dust Cup Filter
Lift fi lter up and out of
dust cup with a twist ing
motion. Clean or replace
with a new fi lter.
Use GENUINE Electrolux replacement dust cup fi lter,
Code EF83.
NOTE: These parts are not dishwasher safe.
NOTE: Your dust cup filter may need to
be replaced if cleaning it does not
restore cleaning performance.
NOTE: Dust cup will not seat unless fi lter is
in place.
11
Page 12
Models equipped with Filter Pads
Check the fi lter pad each time the dust cup is emptied. Replace twice a
year or as needed.
ROUTINE MAINTENANCE
To remove Filter Pad from fi lter door
1. Push down on fi lter door latch and pull door away from cleaner.
2. Lift fi lter pad up and out of fi lter door. Dispose of old fi lter pad.
Filter Pad
Side Door Filters
To replace Filter Pad into fi lter door
1. Place new fi lter pad in fi lter door.
2. Replace fi lter door by placing tabs of door into slots on cleaner.
Rotate door up and against cleaner until it locks into place.
Pre-Motor Filter
Check the pre-motor fi lter each time the dust cup is emptied. Clean or replace
as needed.
To Clean Pre-Motor Filter
1. Remove fi lter centered in the bottom of the dust cup compartment.
2. Shake fi lter to remove excess dust. If necessary, the fi lter can be cleaned
by vacuuming with another cleaner or washing with mild detergent.
3. Reinstall fi lter after completely dry.
Pre-Motor
Filter
Models equipped with HEPA Cartridge Filter
(Only cartridge style fi lters can be used with these models.)
Check the HEPA fi lter each time dust cup is emptied. Replace twice a year or as needed.
Filter
Door
Latch
Carbon Filter (On some models)
Cartridge Latch
Filter Door
Latch
Pull the old fi lter away from the fi lter door and
throw away. Peel tape from adhesive strip on the
new fi lter, place fi lter adhesive side down inside
the fi lter door. Press fi rmly at the top of the fi lter
so adhesive attaches to the fi lter door.
To remove HEPA cartridge fi lter
1. Push down on fi lter door latch and pull door away from cleaner.
2. Push down on HEPA cartridge latch and remove fi lter.
To replace HEPA cartridge fi lter
1. Place bottom tabs of fi lter cartridge into slots. Rotate fi lter toward cleaner, press fi rmly against cleaner to latch. Make
sure HEPA cartridge latch is secured on both sides.
2. Replace fi lter door by placing tabs of door into slots on cleaner. Rotate door up and against cleaner until it locks into place.
12
Page 13
Brush Roll
The brush roll turns as it sweeps and combs the carpet pile.
Remove hair and threads from the brush roll so it continues
brushing the carpet. To maintain the most effi cient cleaning, the
bristles must touch the carpet. To test the bristle length, hold a
ruler against the underneath side of the cleaner. If the bristles
no longer touch the ruler, replace the brush roll.
Brush Roll Belt, Code ZE090
The brush roll belt turns the brush roll to agitate, sweep, and
comb the carpet pile. Check the belt regularly to be sure it is in
good condition. Re place the belt if it stretches, cracks or loses
ten sion. Cut away any hair or threads wound around the brush
roll or the belt pulley because the build up could cause the belt
to rotate unevenly.
How To Replace Brush Roll Belt
NOTE: Turn off the switch and unplug the electrical cord
before replacing belt. Belt pulleys can become hot
during normal use. To pre vent injury, avoid touching
the motor shaft when changing the belt.
5
5. Place new belt around motor shaft.
PERIODIC MAINTENANCE
6
2
2
2
2
1. Lower handle to fl oor to change belt.
2. Remove three screws indicated by screwdrivers in above
illustration. Lift hood to remove.
NOTE: The carpet height adjustment has to be in the
lowest or highest position to remove or reinstall
1
4
Motor
Shaft
Belt
7
8
6. Place belt around brush roll pulley.
7. Align left end cap with base. Push end cap
se cure ly into place.
8. Pull right side of brush roll to stretch belt.
Se cure right end cap into base.
9
IMPORTANT
9. Rotate brush roll by hand two full
rotations to properly po si tion belt.
Brush Roll
Brush Roll Belt
3
3. Lift left end of brush roll.
4. Remove and discard belt.
Brush
Roll
10. Place hood back on cleaner. Make sure hood
front is behind furniture guard. Replace three
screws.
11. Tighten screws.
Use GENUINE Electrolux replacement belt, Code
ZE097.
13
Page 14
To Clear Blockages in Hose
NOTE: Turn off the switch and unplug the electrical cord
be fore clearing hose.
PROBLEM SOLVING
Nested
Tube s
Lower
Hose
Adapter
Base
Hose
Clear Hose
Locate upper hose adapter on the back of the cleaner.
1
Remove nested tubes from back of cleaner for easy
2
access to hose adapter tabs.
Press hose adapter tabs together and pull hose adapter
3
away from cleaner. The hose adapter will unscrew off
hose for easy access to debris if necessary.
Check for blockages at cleaner opening and in hose. If
4
no blockage is found, continue to step 5. If blockage
is found, clear and continue to step 11.
Mini Turbo Nozzle
Models equipped with
Hose
Adapter
Tabs
Mini Turbo Nozzle
Maintenance Instructions
1. To open Turbo Nozzle, push down on lock button.
2. Lift up the bottom housing.
3. Clear Blockage from brush roll area.
Locate lower hose adapter on the back of the cleaner.
5
Remove lower hose adapter from rear of cleaner by lifting
6
up and twisting.
Check for blockages in the hose and base hose. Flexing
7
the hose may help loosen any blockage. If no blockage
is found, continue to step 8. If blockage is found, clear
and continue to step 11.
14
Lock Button
Remove hood from cleaner and check for a blockage in
8
the brush roll area. Make sure the hose inlet is clear.
After the blockage is found and cleared, replace the hood
9
on the cleaner.
10
Place lower hose adapter back into the base hose.
Install the upper hose adapter onto the back of the
11
cleaner, line it up with the cleaner opening and push it
against the cleaner until both tabs lock into place.
Page 15
NOTE: Turn off the switch and unplug the electrical cord before servicing.
Motor will not start. Electric Plug Push plug securely into outlet.
Try another outlet.
Check circuit breaker.
Motor suddenly stops. Thermal Cut Off Page 6.
Does not clean the carpet Filters Clean or replace the fi lters. Hint: If picking up fi ne
or fl oor. dust, the fi lters may not look dirty but a fi ne substance
tends to reduce suction when it blocks the airfl ow
through the fi lter(s).
Dust Cup Be sure the dust cup is properly seated into the cleaner
body. Page 10.
Empty dust cup. Page 10.
Hose Be sure hose adapter is secure on back of cleaner.
Page 14.
Remove any blockages from the hose that restrict the
airfl ow. Page 14.
Check base hose and long hose. Page 14.
Belt Re place a broken, cut, loose or out of shape belt.
Page 13.
Brush Roll Clean hair and thread from bristles and end cap area.
Replace brush roll if bristles are worn. Page 13.
No suction at the end of hose. Hose Adapter Be sure hose adapter is secure. Page 14.
Filters Clean or replace the fi lters. Hint: If picking up fi ne
dust, the fi lters may not look dirty, but a fi ne substance
tends to reduce suction when it blocks the airfl ow
through the fi lters.
PROBLEM CAUSE SOLUTION
✓
✓
✓
✓
✓
✓
✓
✓
✓
Hose Remove any clogs from the hose that restrict the
airfl ow. Check base hose and long hose. Page 14.
Dust Cup Empty dust cup.
Noise from the brush roll Brush Roll Remove hood and clean debris or items from the brush
area. roll area.
Belt Replace a broken, cut, loose or out of shape belt. Page
13.
Cleaner is hard to push. Cleaner Height Setting Put handle in operating position. Tilt the cleaner back
to raise the front wheels off fl oor. Then turn the knob to
a higher setting.
Belt Replace a broken, cut, loose or out of shape belt. Page
13.
Cleaner height knob will Cleaner Height Hint: Put handle in operating position. Tilt the cleaner
not turn. Setting back to raise the front wheels off fl oor. Then turn the
knob.
Dust cup will not go into cleaner. Dust Cup Lid Assembled Filter has to be installed in dust cup or dust cup will not
Properly go into cleaner.
Hood will not come off. Cleaner Height Setting Hood cannot be removed from cleaner unless the
cleaner height setting is in the lowest or highest position.
Screws All three screws must be removed from the top of the
hood. Page 13.
Missing parts Call Electrolux Customer Services on 08706 055055.
Questions? Call Electrolux on 08706 055055. Have the model and
serial numbers ready when you call. See rating plate
beneath the cleaner.
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
PROBLEM SOLVING
Guide
15
Page 16
If you experience any problems with your cleaner,
don’t struggle taking it back to the shop
Call our dedicated Customer Helpline
for help and advice on
08706 055055
Accessory Items in This Carton
1 Dusting/Upholstery Brush 1 extra belt
Turbo Nozzle
(On some models)
1 extension tube,
1 crevice nozzle
Thank you for purchasing
1 Extra Hose
(On some models)
1 accessory
package (2 screws)
1 Spin Duster
(On some models)
an Electrolux cleaner.
Don’t Forget to Use
Genuine Electrolux Belts
Caution: Damages caused by the use of non-genuine
parts are not covered by the Electrolux Guarantee.
1 vacuum cleaner
handle
Part No. 74786A_Rev1 (11/05) Printed in U.S.A.
Loading...