Page 1
aeg.com/register
FSS83828XP
aeg.com\register
EN User Manual | Dishwasher
Page 2
Welcome to AEG! Thank you for choosing our appliance.
My AEG Kitchen app
Get usage advice, brochures, trouble shooter, service and repair information:
www.aeg.com/support
Subject to change without notice.
CONTENTS
1. SAFETY INFORMATION................................................................................ 3
2. SAFETY INSTRUCTIONS.............................................................................. 4
3. INSTALLATION...............................................................................................6
4. PRODUCT DESCRIPTION............................................................................. 7
5. CONTROL PANEL.......................................................................................... 8
6. PROGRAMME SELECTION........................................................................... 9
7. BASIC SETTINGS ........................................................................................12
8. WIRELESS CONNECTION...........................................................................15
9. BEFORE FIRST USE....................................................................................17
10. DAILY USE..................................................................................................18
11. HINTS AND TIPS........................................................................................ 21
12. CARE AND CLEANING.............................................................................. 23
13. TROUBLESHOOTING................................................................................ 27
14. TECHNICAL INFORMATION......................................................................32
15. ENVIRONMENTAL CONCERNS................................................................33
2 ENGLISH
Page 3
1. SAFETY INFORMATION
Before the installation and use of the appliance, carefully read
the supplied instructions. The manufacturer is not responsible
for any injuries or damage that are the result of incorrect
installation or usage. Always keep the instructions in a safe
and accessible location for future reference.
1.1 Children and vulnerable people safety
• This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the
hazards involved.
• Children between 3 and 8 years of age and persons with
very extensive and complex disabilities shall be kept away
from the appliance unless continuously supervised.
• Children of less than 3 years of age should be kept away
from the appliance unless continuously supervised.
• Children should be supervised to ensure that they do not
play with the appliance.
• Keep detergents away from children.
• Keep children and pets away from the appliance when the
door is open.
• Children shall not carry out cleaning and user maintenance
of the appliance without supervision.
1.2 General Safety
• This appliance is for cleaning household-type dishes and
tableware only.
• This appliance is designed for single household domestic
use in an indoor environment.
• This appliance may be used in offices, hotel guest rooms,
bed & breakfast guest rooms, farm guest houses and other
ENGLISH 3
Page 4
similar accommodation where such use does not exceed
(average) domestic usage levels.
• Do not change the specification of this appliance.
• The operating water pressure (minimum and maximum)
must be between 0.05 (0.5) / 1 (10) MPa (bar).
• Follow the maximum number of 14 place settings.
• The appliance door should not be left in an open position to
avoid the tripping hazard.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
• WARNING: Knives and other utensils with sharp points
must be loaded in the basket with their points down or
placed in a horizontal position.
• Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the socket.
• Do not use high pressure water sprays and/or steam to
clean the appliance.
• If the appliance has ventilation openings in the base, they
must not be covered e.g. by a carpet.
• The appliance is to be connected to the water mains using
the new supplied hose-sets. Old hose sets must not be
reused.
2. SAFETY INSTRUCTIONS
2.1 Installation
WARNING!
Only a qualified person must install this
appliance.
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Follow the installation instructions supplied
with the appliance.
• Always take care when moving the
appliance as it is heavy. Always use safety
gloves and enclosed footwear.
4 ENGLISH
• Do not install or use the appliance where
the temperature is less than 0 °C.
• Install the appliance in a safe and suitable
place that meets installation requirements.
• Do not use the appliance before installing
it in the built-in structure due to safety
manner.
2.2 Electrical connection
WARNING!
Risk of fire and electric shock.
Page 5
• Warning: this appliance is designed to be
installed / connected to a grounding
connection in the building.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable. Should
the mains cable need to be replaced, this
must be carried out by our Authorised
Service Centre.
• Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug.
2.3 Water connection
• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not
used for a long time, where repair work
has been carried out or new devices fitted
(water meters, etc.), let the water flow until
it is clean and clear.
• Ensure that there are no visible water
leaks during and after the first use of the
appliance.
• If the water inlet hose is damaged,
immediately close the water tap and
disconnect the mains plug from the mains
socket. Contact the Authorised Service
Centre to replace the water inlet hose.
• Without electrical power, the water
protection system is not active. In this
case there is a risk of flooding.
• The water inlet hose has a safety valve
and a sheath with an inner mains cable.
WARNING!
Dangerous voltage.
2.4 Use
• Do not put flammable products or items
that are wet with flammable products in,
near or on the appliance.
• Dishwasher detergents are dangerous.
Follow the safety instructions on the
detergent packaging.
• Do not drink and play with the water in the
appliance.
• Do not remove the dishes from the
appliance until the programme is
complete. Some detergent may remain on
the dishes.
• Do not store items or apply pressure on
the open door of the appliance.
• The appliance can release hot steam if
you open the door while a programme
operates.
2.5 Service
• To repair the appliance contact the
Authorised Service Centre. Use original
spare parts only.
• Please note that self-repair or nonprofessional repair can have safety
consequences and might void the
guarantee.
• The following spare parts are available for
at least 7 years after the model has been
discontinued: motor, circulation and drain
pump, heaters and heating elements,
including heat pumps, piping and related
equipment including hoses, valves, filters
and aquastops, structural and interior
parts related to door assemblies, printed
circuit boards, electronic displays,
pressure switches, thermostats and
ENGLISH 5
Page 6
sensors, software and firmware including
www.youtube.com/electrolux
www.youtube.com/aeg
How to install your AEG/Electrolux
60 cm Sliding Door Dishwasher
min. 550
reset software. The following spare parts
are available for at least 10 years after the
model has been discontinued: door hinge
and seals, other seals, spray arms, drain
filters, interior racks and plastic
peripherals such as baskets and lids. The
duration may be longer in your country.
For further information, please visit our
website.
• Please note that some of these spare
parts are only available to professional
repairers, and that not all spare parts are
relevant for all models.
• Concerning the lamp(s) inside this product
and spare part lamps sold separately:
These lamps are intended to withstand
extreme physical conditions in household
appliances, such as temperature,
3. INSTALLATION
WARNING!
Refer to Safety chapters before
installation.
For detailed installation information, see the
installation instruction supplied with the
appliance.
Valid only for Germany: Before installation,
refer to the chapter "Rückschlagventil" in the
German user manual.
vibration, humidity, or are intended to
signal information about the operational
status of the appliance. They are not
intended to be used in other applications
and are not suitable for household room
illumination.
2.6 Disposal
WARNING!
Risk of injury or suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children
and pets to get closed in the appliance.
3.1 Building in
6 ENGLISH
3.2 Safety caps
If the furniture panel is not installed, open the
appliance door carefully to avoid the risk of
injury.
After installation, make sure the plastic
covers are locked in position. Damage or
removal of the plastic covers on the sides of
the door may impact the functionality of the
appliance and may cause an injury. If the
plastic cover is damaged, contact the
Authorized Service Centre to replace it with
the new one.
Page 7
max
5 mm
4. PRODUCT DESCRIPTION
5
4
9
67
13
12
11
10
14
2
3
1
8
Ceiling spray arm
1
Upper spray arm
2
Lower spray arm
3
Filters
4
Rating plate
5
Salt container
6
Air vent
7
Rinse aid dispenser
8
ENGLISH 7
Page 8
Detergent dispenser
1 2 3
4 5 6
9
ComfortLift basket
10
Trigger handle
11
Lower basket handle
12
Upper basket
13
Cutlery drawer
14
4.1 QR code on the rating plate
The rating plate has a QR code that can be
used in two ways.
Scan the QR code with the camera on your
mobile device to be redirected to My AEG
Kitchen app in the app store. Follow the
instructions on your mobile device to
download the app.
Scan the QR code with the scanner in My
AEG Kitchen app to pair the dishwasher with
your mobile device.
4.2 Beam-on-Floor
The Beam-on-Floor is a light that is displayed
on the floor below the appliance door.
5. CONTROL PANEL
On/Off button / Reset button
1
Delay start button / Remote start button
2
Display
3
MY TIME program selection bar
4
• A red light comes on when a programme
starts. It remains on for the duration of the
programme.
• A green light comes on when the
programme is complete.
• The red light flashes when the appliance
has a malfunction.
The Beam-on-Floor is off when the
appliance is deactivated.
Option buttons (EXTRAS)
5
AUTO Sense program button
6
8 ENGLISH
Page 9
5.1 Display
A
C BB B
CA B D E
A. ECOMETER
B. Indicators
C. Time indicator
5.3 Indicators
Indicator Description
Rinse aid indicator. It is on when the rinse aid dispenser needs refilling. Refer to "Before first
use".
Salt indicator. It is on when the salt container needs refilling. Refer to "Before first use".
Machine Care indicator. It is on when the appliance needs internal cleaning with the Machine
Care programme. Refer to "Care and cleaning".
Drying phase indicator. It is on when you select a programme with the drying phase. It flash‐
es when the drying phase operates. Refer to "Programme selection".
Wi-Fi indicator. It is on when you activate the wireless connection. Refer to "Wireless con‐
nection".
5.2 ECOMETER
The ECOMETER indicates how the
programme selection impacts energy and
water consumption. The more bars are on,
the lower the consumption is.
indicates the most environmentally
friendly programme selection for a normally
soiled dishwashing load.
6. PROGRAMME SELECTION
6.1 MY TIME
MY TIME selection bar allows to select a
suitable dishwashing cycle based on
programme duration.
A. Quick is the shortest programme (30min)
suitable for dishwashing a load with fresh
and light soil.
B. 1h is a programme suitable for
dishwashing a load with fresh and lightly
dried-on soil.
C. 1h 30min is a programme suitable for
dishwashing and drying normally soiled
items.
D. 2h 40min is a programme suitable for
dishwashing and drying heavily soiled
items.
E. ECO is the longest programme offering
the most efficient use of energy and water
consumption for crockery and cutlery with
ENGLISH 9
Page 10
normal soil. This is the standard
programme for test institutes.
1)
6.2 AUTO Sense
The AUTO Sense programme automatically
adjusts the dishwashing cycle to the type of
load.
The appliance senses the degree of soil and
the amount of dishes in the baskets. It adjusts
the temperature and quantity of water as well
as the wash duration.
6.3 EXTRAS
You can adjust the programme selection to
your needs by activating EXTRAS.
ExtraSilent
ExtraSilent allows to reduce the noise
generated by the appliance. When the option
is activated, the wash pump works quietly at
a lower speed. Due to the low speed, the
programme duration is longer.
6.5 Programmes overview
ExtraPower
ExtraPower improves the dishwashing
results of the selected programme. The
option increases the wash temperature and
duration.
GlassCare
GlassCare prevents delicate load,
glassware in particular, from damaging. The
option prevents rapid changes in the
dishwashing temperature of the selected
programme and reduces it to 45 °C.
6.4 Extras in the app
My AEG Kitchen app provides additional
dishwashing options. To access all options,
connect your dishwasher to the app. See
chapter "Wireless connection".
Programme Dishwasher
load
Quick Crockery, cutlery Fresh
All All
3)
Pre-rinse
1h Crockery, cutlery Fresh, lightly
1h 30min Crockery, cut‐
1)
This programme is used to assess compliance with the Ecodesign Comission Regulation (EU) 2019/2022.
lery, pots, pans
Degree of
soil
dried-on
Normal, lightly
dried-on
Programme phases EXTRAS
• Dishwashing 50 °C
• Intermediate rinse
• Final rinse 45 °C
• AirDry
• Prewash
• Dishwashing 60 °C
• Intermediate rinse
• Final rinse 50 °C
• AirDry
• Dishwashing 60 °C
• Intermediate rinse
• Final rinse 55 °C
• Drying
• AirDry
1)
1)
1)
• ExtraPower
• GlassCare
• ExtraHygiene
Not applicable
• ExtraPower
• GlassCare
• ExtraHygiene
• ExtraPower
• GlassCare
• ExtraHygiene
10 ENGLISH
2)
2)
2)
Page 11
Programme Dishwasher
load
2h 40min Crockery, cut‐
ECO Crockery, cut‐
AUTO Sense Crockery, cut‐
Machine Care For cleaning the appliance interior.
1)
Automatic door opening during the drying phase. Refer to "Basic settings".
2)
Available only through My AEG Kitchen app.
3)
Available only through My AEG Kitchen app.
lery, pots, pans
lery, pots, pans
lery, pots, pans
Refer to "Care and Cleaning".
Degree of
soil
Normal to
heavy, dried-on
Normal, lightly
dried-on
All
Programme phases EXTRAS
• Prewash
• Dishwashing 60 °C
• Intermediate rinse
• Final rinse 60 °C
• Drying
• AirDry
• Prewash
• Dishwashing 50 °C
• Intermediate rinse
• Final rinse 55 °C
• Drying
• AirDry
• Prewash
• Dishwashing 50 - 60 °C
• Intermediate rinse
• Final rinse 60 °C
• Drying
• AirDry
• Cleaning 70 °C
• Intermediate rinse
• Final rinse
• AirDry
1)
1)
1)
1)
• ExtraPower
• GlassCare
• ExtraHygiene
• ExtraPower
• GlassCare
• ExtraHygiene
• ExtraSilent
Not applicable
Not applicable
2)
2)
Consumption values
Programme
1)2)
Quick 11.0 0.620 30
Pre-rinse 5.0 0.010 15
1h 11.8 0.970 60
1h 30min 11.9 1.110 90
2h 40min 11.9 1.210 160
ECO 11.0 0.848 240
AUTO Sense 12.1 1.220 170
Water (l) Energy (kWh) Duration (min)
ENGLISH 11
Page 12
Programme
1 2 3 4 5
1)
The pressure and the temperature of the water, the variations of the mains supply, the options, the quantity of
dishes and the degree of soil can change the values.
2)
The values for programmes other than ECO are indicative only.
1)2)
Machine Care 10.6 0.710 60
Water (l) Energy (kWh) Duration (min)
Information for test institutes
To receive the necessary information for
conducting performance tests (e.g. according
to: EN60436 ), send an email to:
In your request, include the product number
code (PNC) from the rating plate.
For any other questions regarding your
dishwasher, refer to the service book
provided with your appliance.
info.test@dishwasher-production.com
7. BASIC SETTINGS
You can configure the appliance by changing basic settings according to your needs.
Number Setting Values
1 Water hardness 1L - 10L (default:
2 Rinse aid level 0A - 6A (default: 4A) Adjust the level of the rinse aid according to the nec‐
3 End sound On
4 Auto door open On (default)
5 Key tones On (default)
1)
For more details, refer to the information provided in this chapter.
5L)
Off (default)
Off
Off
Description
Adjust the level of the water softener according to the
water hardness in your area.
essary dosage.
Activate or deactivate the acoustic signal for the end
of a programme.
Activate or deactivate the AirDry.
Activate or deactivate the sound of the buttons when
pressed.
You can change the basic settings in setting
mode.
When the appliance is in setting mode, the
bars of the ECOMETER represent available
settings. For each setting, a dedicated bar of
the ECOMETER flashes.
The order of the basic settings presented in
the table is also the order of the settings on
the ECOMETER:
7.1 Setting mode
1)
12 ENGLISH
How to navigate in setting mode
You can navigate in setting mode using
MY TIME selection bar.
Page 13
BA C
A. Previous button
B. OK button
C. Next button
Use Previous and Next to switch between
the basic settings and to change their value.
Use OK to enter the selected setting and to
confirm changing its value.
How to enter setting mode
You can enter setting mode before starting a
programme. You cannot enter setting mode
while the programme is running.
To enter setting mode, press and hold
simultaneously
and for about 3
seconds.
The lights related to the Previous, OK and
Next are on.
How to change a setting
Make sure the appliance is in setting mode.
1. Use Previous or Next to select the bar of
the ECOMETER dedicated to the desired
setting.
• The bar of the ECOMETER dedicated
to the chosen setting flashes.
• The display shows the current setting
value.
2. Press OK to enter the setting.
• The bar of the ECOMETER dedicated
to the chosen setting is on. The other
bars are off.
• The current setting value flashes.
3. Press Previous or Next to change the
value.
4. Press OK to confirm the setting.
• The new setting is saved.
• The appliance returns to the basic
settings list.
5. Press and hold simultaneously
and for about 3 seconds to exit
setting mode.
The appliance returns to the programme
selection.
The saved settings remain valid until you
change them again.
7.2 The water softener
The water softener removes minerals from
the water supply, which would have a
negative effect on the washing results and on
the appliance.
The higher the content of these minerals, the
harder your water is. Water hardness is
measured in equivalent scales.
The water softener should be adjusted
according to the hardness of the water in your
area. Your local water authority can advise
you on the hardness of the water in your
area. Set the right level of the water softener
to assure good washing results.
Water hardness
German de‐
grees (°dH)
47 - 50 84 - 90 8.4 - 9.0 835 - 904 58 - 63 10
43 - 46 76 - 83 7.6 - 8.3 755 - 834 53 - 57 9
37 - 42 65 - 75 6.5 - 7.5 645 - 754 46 - 52 8
29 - 36 51 - 64 5.1 - 6.4 505 - 644 36 - 45 7
23 - 28 40 - 50 4.0 - 5.0 395 - 504 28 - 35 6
19 - 22 33 - 39 3.3 - 3.9 325 - 394 23 - 27
French de‐
grees (°fH)
mmol/l mg/l (ppm) Clarke de‐
grees
Water softener
level
1)
5
ENGLISH 13
Page 14
German de‐
grees (°dH)
15 - 18 26 - 32 2.6 - 3.2 255 - 324 18 - 22 4
11 - 14 19 - 25 1.9 - 2.5 185 - 254 13 - 17 3
4 - 10 7 - 18 0.7 - 1.8 70 - 184 5 - 12 2
<4 <7 <0.7 <70 < 5
1)
Factory setting.
2)
Do not use salt at this level.
French de‐
grees (°fH)
mmol/l mg/l (ppm) Clarke de‐
grees
Water softener
level
2)
1
Regardless of the type of detergent used,
set the proper water hardness level to
keep the salt refill indicator active.
Multi-tabs containing salt are not effective
enough to soften hard water.
Regeneration process
For the correct water softener operation, the
resin of the softener device needs to be
regenerated regularly. This process is
automatic and is the part of the normal
dishwasher operation.
When the prescribed quantity of water (see
values in the table) has been used since the
previous regeneration process, a new
regeneration process will be initiated between
the final rinse and the programme end.
Water softener level Amount of water (l)
1 250
2 100
3 62
4 47
5 25
6 17
7 10
8 5
9 3
10 3
In case of the high water softener setting, it
may occur also in the middle of the
programme, before the rinse (twice during a
programme). Regeneration initiation has no
impact on the cycle duration, unless it occurs
in the middle of a programme or at the end of
a programme with a short drying phase. In
such cases, the regeneration prolongs the
total duration of a programme by additional 5
minutes.
Subsequently, the rinsing of the water
softener that lasts 5 minutes may begin in the
same cycle or at the beginning of the next
programme. This activity increases the total
water consumption of a programme by
additional 4 litres and the total energy
consumption of a programme by additional 2
Wh. The rinsing of the softener ends with a
complete drain.
Each performed softener rinse (possible more
than one in the same cycle) may prolong the
programme duration by another 5 minutes
when it occurs at any point at the beginning
or in the middle of a programme.
All the consumption values mentioned in
this section are determined in line with
the currently applicable standard in
laboratory conditions with water hardness
2.5mmol/L (water softener: level 3)
according to the regulation: 2019/2022 .
The pressure and the temperature of
water as well as the variations of the
mains supply can change the values.
7.3 The rinse aid level
The rinse aid helps to dry the dishes without
streaks and stains. It is automatically
released during the hot rinse phase. It is
14 ENGLISH
Page 15
possible to set the released quantity of rinse
aid.
When rinse aid chamber is empty, the rinse
aid indicator is on notifying to refill rinse aid. If
the drying results are satisfactory while using
multi-tablets only, it is possible to deactivate
the dispenser and the indicator. However, for
best drying performance, always use rinse
aid and keep the rinse aid indicator active.
To deactivate the rinse aid dispenser and
indicator, set the level of rinse aid to 0A.
7.4 End sound
You can activate an acoustic signal that
sounds when the programme is completed.
Acoustic signals sound also when a
malfunction of the appliance occurs. It is
not possible to deactivate these signals.
AirDry is automatically activated with all
programmes.
The duration of the drying phase and the door
opening time vary depending on the selected
programme and options.
When AirDry opens the door, the display
shows the remaining time of the running
programme.
CAUTION!
Do not try to close the appliance door
within 2 minutes after automatic opening.
This can cause damage to the appliance.
CAUTION!
If children have access to the appliance,
we advise to deactivate AirDry. The
automatic opening of the door may pose
a danger.
7.5 AirDry
AirDry improves the drying results. The
appliance door opens automatically during
the drying phase and remains ajar.
8. WIRELESS CONNECTION
You can connect your dishwasher to the
home wireless network and then link it to your
mobile devices in My AEG Kitchen app. This
functionality allows you to remotely control
and monitor your dishwasher.
My AEG Kitchen app is available for
download from the app store on your mobile
When AirDry opens the door, Beam-onFloor might not be completely visible. To
see if the programme is complete, look at
the control panel.
7.6 Key tones
The buttons on the control panel make a click
sound when you press them. You can
deactivate this sound.
device. You can scan the QR code from the
rating plate to be redirected to the app (see
chapter "Product description").
The app is compatible with iOS and Android
operating systems. Check the compatible
versions of the operating systems in the app
store.
ENGLISH 15
Page 16
Wi-Fi module parameters
Wi-Fi module NIUS-SA
Frequency 2.412 - 2.472 GHz
Protocol IEEE 802.11 b-g-n
Max Power <20 dBm
Encryption WPA, WPA2
8.1 How to connect the dishwasher to the network and to the app
To connect your dishwasher, you need:
• Wireless network with the Internet
connection.
• Mobile device connected to the wireless
network.
1. Launch My AEG Kitchen app on your
mobile device and follow the instructions
in the app. When prompted in the app,
activate the wireless connection in the
dishwasher.
2. To activate the wireless connection, press
and hold simultaneously and
for 2 seconds.
• The indicator flashes.
• The display shows On for a few
seconds and then AP.
• All buttons are inactive except for the
on/off button.
3. When prompted, enter the home network
credentials in My AEG Kitchen app.
If the credentials are not entered, the
dishwasher cancels the procedure after
some time and returns to the programme
selection.
If the connection is successful, the indicator
is steady and the letters AP are off.
The appliance returns to the programme
selection. Refer to "Daily use" to activate the
remote start.
If you want to cancel the procedure, switch
the appliance off and on.
8.2 How to deactivate the wireless connection
Press and hold simultaneously and
for 2 seconds.
• The indicator is off.
• The display shows Off for a few
seconds.
• The appliance returns to the
programme selection.
8.3 How to activate the wireless connection
Press and hold simultaneously and
for 2 seconds.
• The indicator is on.
• The display shows On for a few
seconds.
• The appliance returns to the
programme selection.
Refer to "Daily use" to activate the remote
start.
8.4 How to reset the network credentials
If you want to connect to a different wireless
network or update the credentials of the
current network, reset the network
credentials.
Press and hold simultaneously and
for about 5 seconds.
• The display shows Off and then --- for
a few seconds.
• The indicator is off.
• The appliance returns to the
programme selection.
Connect the dishwasher to the network and
to the app to enter new network credentials.
Refer to the instructions provided earlier in
this chapter.
If the connection is unsuccessful or the
display shows upd, refer to
"Troubleshooting".
16 ENGLISH
Page 17
9. BEFORE FIRST USE
1. Make sure that the current level of the
water softener agrees with the
hardness of the water supply. If not,
adjust the level of the water softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start the programme Quick to remove
any residuals from the manufacturing
process. Do not use detergent and do not
put dishes in the baskets.
After starting the programme, the appliance
recharges the resin in the water softener for
up to 5 minutes. The washing phase starts
only after this procedure is complete. The
procedure is repeated periodically.
9.1 The salt container
CAUTION!
Use only regeneration salt for
dishwashers. Do not use kitchen salt.
The salt is used to recharge the resin in the
water softener and to assure good washing
results in daily use.
How to fill the salt container
Make sure that the ComfortLift basket is
empty and locked in the raised position.
1. Turn the cap of the salt container
counterclockwise and remove it.
2. Put 1 litre of water in the salt container
(only for the first time).
3. Fill the salt container with dishwasher salt
(until it is full).
4. Carefully shake the funnel by its handle to
get the last granules inside.
5. Remove the salt around the opening of
the salt container.
6. Turn the cap clockwise to close the salt
container.
CAUTION!
Water and salt can come out of the salt
container when you fill it. To prevent
corrosion, fill the salt container and then
immediately start a complete
dishwashing cycle with detergent.
ENGLISH 17
Page 18
9.2 How to fill the rinse aid
A
B
C
dispenser
CAUTION!
The compartment (B) is for rinse aid only.
Do not fill it with detergent.
10. DAILY USE
CAUTION!
Only use rinse aid designed specifically
for dishwashers.
1. Open the lid (C).
2. Fill the dispenser (B) until the rinse aid
reaches the marking ''MAX''.
3. Remove the spilled rinse aid with an
absorbent cloth to prevent excessive
foam formation.
4. Close the lid. Make sure that the lid locks
into position.
Fill the rinse aid dispenser when the
indicator (A) is clear.
1. Open the water tap.
2. Press and hold until the appliance is
activated.
3. Fill the salt container if it is empty.
4. Fill the rinse aid dispenser if it is empty.
5. Load the baskets.
6. Add the detergent.
7. Select and start a programme.
8. Close the water tap when the programme
is complete.
10.1 ComfortLift
CAUTION!
Do not sit on the rack or put excessive
pressure on the locked basket.
CAUTION!
Do not exceed the max load capacity of
18 kg.
18 ENGLISH
CAUTION!
Make sure that items do not stick out of
the basket frame as it can cause damage
to the items and the ComfortLift
mechanism.
The ComfortLift mechanism allows to lift the
lower rack up (to the second rack level) and
put it down to load and unload dishes easily.
To load or unload the lower basket:
1. Lift the basket by pulling the rack out of
the dishwasher by the basket handle. The
trigger handle should not be used.
Page 19
The basket is automatically locked on the
A
B
C
upper level.
2. Carefully place items in the basket or
remove them (refer to the basket loading
leaflet).
3. Lower the basket by connecting the
trigger handle with the basket frame as
shown below. Lift the trigger handle
completely and the basket handle slightly
until the basket is disengaged on both
sides.
Once the basket is unlocked, push the
rack down. The mechanism returns to its
default position on the lower level.
There are two ways of lowering the
basket depending on the loading:
• If there is a full load of plates, slightly
push the basket down.
• If the basket is empty or half-loaded,
press the basket down.
10.2 Using the detergent
1. Press the release button (A) to open the
lid (C).
2. Put the detergent (gel, powder or tablets)
in the compartment (B).
3. If the programme has a prewash phase,
put a small quantity of detergent on the
inner part of the appliance door.
4. Close the lid. Make sure that the lid locks
into position.
For information about the detergent
dosage, refer to the manufacturer's
instructions on the packaging of the
product. Usually, 20 - 25 ml of gel
detergent is adequate for washing a load
with normal soil.
The upper ends of the two vertical ribs
inside the compartment (B) indicate the
maximum level for filling the dispenser
with gel (max. 30ml).
10.3 Remote start
Activate this function to remotely control and
monitor your dishwasher in My AEG Kitchen
app.
How to activate the remote start
Make sure that the indicator is on
and your dishwasher is added in My AEG
Kitchen app. If not, refer to "Wireless
connection".
CAUTION!
Only use detergent specifically designed
for dishwashers.
1. Press .
• The light related to the button is on.
• The display shows APP.
2. Close the appliance door.
3. Use My AEG Kitchen app to remotely
operate the appliance.
Opening the door deactivates the remote
start. Refer to the information provided
further in this chapter.
ENGLISH 19
Page 20
How to deactivate the remote start
Press until the display shows 0h.
• The light related to the button is off.
• The appliance returns to the
programme selection.
10.4 How to select and start a programme using MY TIME selection bar
1. Slide your finger across MY TIME
selection bar to choose a suitable
programme.
• The light related to the selected
programme is on.
• The ECOMETER indicates the level of
energy and water consumption.
• The display shows the programme
duration.
2. Activate applicable EXTRAS if desired.
3. Close the appliance door to start the
programme.
10.5 How to activate EXTRAS
1. Select a programme using MY TIME
selection bar.
2. Press the button dedicated to the option
you want to activate.
• The light related to the button is on.
• The display shows the updated
programme duration.
• ECOMETER indicates the updated
level of energy and water
consumption.
By default, options must be activated
every time before you start a programme.
It is not possible to activate or deactivate
options while a programme is running.
Not all options are compatible with each
other.
Activating options often increases the
water and energy consumption as well as
the programme duration.
10.6 How to start the AUTO Sense program
1. Press .
• The light related to the button is on.
• The display shows the longest
possible program duration.
2. Close the appliance door to start the
program.
The appliance senses the type of load and
adjusts a suitable wash cycle. During the
cycle, the sensors operate several times and
the initial program duration can decrease.
10.7 How to delay the start of a
programme
1. Select a programme.
2. Double press .
The display shows 1h.
3. Press repeatedly until the display
shows the desired delay time (from 1 to
24 hours).
4. Close the appliance door to start the
countdown.
When you set the delay start, the remote start
is automatically activated.
During the countdown, you cannot change
the programme selection. You can change
the delay time in the app.
When the countdown is complete, the
programme starts.
10.8 How to cancel the delay start
while the countdown operates
Press and hold for about 3 seconds.
The appliance returns to the programme
selection.
If you cancel the delay start, you have to
select the programme again.
20 ENGLISH
Page 21
10.9 How to cancel a running programme
Press and hold for about 3 seconds.
The appliance returns to the programme
selection.
If the door is opened for more than 30
seconds during the drying phase, the
running programme ends. It does not
happen if the door is opened by the
AirDry function.
Make sure that there is detergent in the
detergent dispenser before you start a
new programme.
10.10 Opening the door while the appliance operates
Opening the door while a programme is
running pauses the wash cycle. The display
shows the remaining duration of the
programme. After closing the door, the wash
cycle resumes from the point of interruption.
Opening the door while the remote start is
activated deactivates this function. Activate
the remote start again before you close the
door; otherwise, the wash cycle starts
immediately after you close the door.
Opening the door does not deactivate the
remote start if the delay start is set.
If you open the door during the delay start
countdown, the countdown is paused. The
display shows the current countdown status.
After closing the door, the countdown
resumes.
Opening the door while the appliance
operates may affect the energy
consumption and the programme
duration.
10.11 The Auto Off function
This function saves energy by switching the
appliance off when it is not operating.
The function comes into operation
automatically:
• When the programme is completed.
• After 5 minutes if a programme was not
started.
10.12 End of the programme
When the programme is complete, the
display shows 0:00.
The Auto Off function switches the appliance
off automatically.
All buttons are inactive except for the on/off
button.
If the display shows upd, refer to
"Troubleshooting".
11. HINTS AND TIPS
11.1 General
Follow the hints below to ensure optimal
cleaning and drying results in daily use and to
protect the environment.
• Washing dishes in the dishwasher as
instructed in the user manual usually
consumes less water and energy than
washing dishes by hand.
• Load the dishwasher to its full capacity to
save water and energy. For best cleaning
results, arrange items in the baskets as
instructed in the user manual and do not
overload the baskets.
• Do not pre-rinse dishes by hand. It
increases the water and energy
consumption. When needed, select a
programme with a prewash phase.
ENGLISH 21
Page 22
• Remove larger residues of food from the
dishes and empty cups and glasses
before putting them inside the appliance.
• Soak or slightly scour cookware with firmly
cooked-on or baked-on food before
washing it in the appliance.
• Make sure that items in the baskets do not
touch or cover each other. Only then can
the water completely reach and wash the
dishes.
• You can use dishwasher detergent, rinse
aid and salt separately or you can use the
multi-tablets (e.g. ''All in 1''). Follow the
instructions on the packaging.
• Select a programme according to the type
of load and the degree of soil. ECO offers
the most efficient use of water and energy
consumption.
• To prevent limescale buildup inside the
appliance:
– Refill the salt container whenever
necessary.
– Use the recommended dosage of the
detergent and rinse aid.
– Make sure that the current level of the
water softener agrees with the
hardness of the water supply.
– Follow the instructions in the chapter
"Care and cleaning".
11.2 Using salt, rinse aid and
detergent
• Only use salt, rinse aid and detergent
designed for dishwasher. Other products
can cause damage to the appliance.
• In areas with hard and very hard water, we
recommend to use basic dishwasher
detergent (powder, gel, tablets containing
no additional agents), rinse aid and salt
separately for optimal cleaning and drying
results.
• Detergent tablets do not fully dissolve with
short programmes. To prevent detergent
residues on the tableware, we recommend
that you use tablets with long
programmes.
• Always use the correct quantity of
detergent. Insufficient dosage of detergent
can result in poor cleaning results and
hard-water filming or spotting on the items.
Using too much detergent with soft or
softened water results in detergent
residues on the dishes. Adjust the amount
of detergent based on the water hardness.
Refer to the instructions on the detergent
packaging.
• Always use the correct quantity of rinse
aid. Insufficient dosage of rinse aid
decreases the drying results. Using too
much rinse aid results in bluish layers on
the items.
• Make sure that the water softener level is
correct. If the level is too high, the
increased quantity of salt in the water
might result in rust on cutlery.
11.3 What to do if you want to stop
using multi-tablets
Before you start using separately detergent,
salt and rinse aid, complete the following
steps:
1. Set the highest level of the water
softener.
2. Make sure that the salt and rinse aid
containers are full.
3. Start the Quick programme. Do not add
detergent and do not put dishes in the
baskets.
4. When the programme is completed,
adjust the water softener according to the
water hardness in your area.
5. Adjust the released quantity of rinse aid.
11.4 Before starting a programme
Before you start the selected programme,
make sure that:
• The filters are clean and correctly
installed.
• The cap of the salt container is tight.
• The spray arms are not clogged.
• There is enough salt and rinse aid (unless
you use multi-tablets).
• The arrangement of the items in the
baskets is correct.
• The programme is suitable to the type of
load and the degree of soil.
• The correct quantity of detergent is used.
11.5 Loading the baskets
• Always use the whole space of the
baskets.
• Use the appliance to wash dishwashersafe items only.
22 ENGLISH
Page 23
• Do not wash in the appliance items made
of wood, horn, aluminium, pewter and
copper as they could crack, warp, get
discoloured or pitted.
• Do not wash in the appliance items that
can absorb water (sponges, household
cloths).
• Put hollow items (cups, glasses and pans)
with the opening facing downwards.
• Make sure that glass items do not touch
each other.
• Put light items in the upper basket. Make
sure that the items do not move freely.
• Put cutlery and small items in the cutlery
drawer.
• Move the upper basket upwards to
accommodate large items in the lower
basket.
12. CARE AND CLEANING
• Make sure that the spray arms can move
freely before you start a programme.
11.6 Unloading the baskets
1. Let the tableware cool down before you
remove it from the appliance. Hot items
can be easily damaged.
2. First remove items from the lower basket,
then from the upper basket.
After the programme is completed, water
can still remain on the inside surfaces of
the appliance.
WARNING!
Before any maintenance other than
running the programme Machine Care,
deactivate the appliance and disconnect
the mains plug from the main socket.
Make sure that the ComfortLift basket is
empty and locked in the raised position.
Dirty filters and clogged spray arms
negatively affect the washing results.
Check these elements regularly and, if
necessary, clean them.
12.1 Machine Care
Machine Care is a programme designed to
clean the appliance interior with optimal
results. It removes limescale and grease
buildup.
When the appliance senses the need for
cleaning, the indicator is on. Start the
Machine Care programme to clean the
appliance interior.
How to start the Machine Care programme
Before starting the Machine Care
programme, clean the filters and spray
arms.
1. Use a descaler or a cleaning product
designed specifically for dishwashers.
Follow the instructions on the packaging.
Do not put dishes in the baskets.
2. Press and hold simultaneously and
for about 3 seconds.
The indicators and flash. The display
shows the programme duration.
3. Close the appliance door to start the
programme.
When the programme is complete, the
indicator is off.
12.2 Internal cleaning
• Clean the appliance interior with a soft
damp cloth.
• Do not use abrasive products, abrasive
cleaning pads, sharp tools, strong
chemicals, scourer or solvents.
• Wipe clean the door, including the rubber
gasket, once a week.
ENGLISH 23
Page 24
• To maintain the performance of your
C
B
A
appliance, use a cleaning product
designed specifically for dishwashers at
least once every two months. Carefully
follow the instructions on the packaging of
the product.
• For optimal cleaning results, start the
programme Machine Care.
12.3 Removal of foreign objects
Check the filters and the sump after each use
of the dishwasher. Foreign objects (e.g.
pieces of glass, plastic, bones or toothpicks,
etc) decrease the cleaning performance and
can cause damage to the drain pump.
CAUTION!
If unable to remove the foreign objects,
contact an Authorised Service Centre.
1. Disassemble the filters system as
instructed in this chapter.
2. Remove any foreign objects manually.
3. Reassemble the filters as instructed in
this chapter.
12.4 External cleaning
• Clean the appliance with a moist soft
cloth.
• Only use neutral detergents.
• Do not use abrasive products, abrasive
cleaning pads or solvents.
1. Turn the filter (B) counterclockwise and
remove it.
2. Remove the filter (C) out of filter (B).
3. Remove the flat filter (A).
4. Wash the filters.
12.5 Cleaning the filters
The filter system is made of 3 parts.
24 ENGLISH
5. Make sure that there are no residues of
food or soil in or around the edge of the
sump.
6. Put back in place the flat filter (A). Make
sure that it is correctly positioned under
the 2 guides.
Page 25
7. Reassemble the filters (B) and (C).
8. Put back the filter (B) in the flat filter (A).
Turn it clockwise until it locks.
2. Wash the spray arm under running water.
Use a thin pointed tool, e.g. a toothpick,
to remove particles of soil from the holes.
CAUTION!
An incorrect position of the filters can
cause bad washing results and damage
to the appliance.
12.6 Cleaning the lower spray arm
We recommend to clean the lower spray arm
regularly to prevent soil from clogging the
holes.
Clogged holes can cause unsatisfactory
washing results.
1. To remove the lower spray arm, pull it
upwards.
3. To install the spray arm back, press it
downwards.
12.7 Cleaning the upper spray arm
We recommend to clean the upper spray arm
regularly to prevent soil from clogging the
holes.
Clogged holes can cause unsatisfactory
washing results.
1. Pull out the upper basket.
ENGLISH 25
Page 26
2. To detach the spray arm from the basket,
C
B
A
1
2
press the spray arm upwards and
simultaneously turn it clockwise.
3. Wash the spray arm under running water.
Use a thin pointed tool, e.g. a toothpick,
to remove particles of soil from the holes.
holes. Clogged holes can cause
unsatisfactory washing results.
The ceiling spray arm is placed on the ceiling
of the appliance. The spray arm (C) is
installed in the delivery tube (A) with the
mounting element (B).
1. Release the stoppers on the sides of the
sliding rails of the cutlery drawer and pull
the drawer out.
4. To install the spray arm back, press the
spray arm upwards and simultaneously
turn it counterclockwise until it locks into
place.
12.8 Cleaning the ceiling spray arm
We recommend to clean the ceiling spray
arm regularly to prevent soil from clogging the
26 ENGLISH
2. Move the upper basket to the lowest level
to reach the spray arm more easily.
3. To detach the spray arm (C) from the
delivery tube (A), turn the mounting
element (B) counterclockwise and pull the
spray arm downwards.
4. Wash the spray arm under running water.
Use a thin pointed tool, e.g. a toothpick,
to remove particles of soil from the holes.
Run the water through the holes to wash
soil particles away from the inside.
Page 27
13. TROUBLESHOOTING
5. To install the spray arm (C) back, insert
the mounting element (B) in the spray
arm and fix it in the delivery tube (A) by
turning it clockwise. Make sure that the
mounting element locks into place.
6. Install the cutlery drawer on the sliding
rails and block the stoppers.
WARNING!
Improper repair of the appliance may
pose a danger to the safety of the user.
Any repairs must be performed by
Refer to the below table for information on
possible problems.
With some problems, the display shows an
alarm code.
qualified personnel.
The majority of problems that may occur
can be solved without the need to contact
an Authorised Service Centre.
Problem and alarm code Possible cause and solution
You cannot activate the appliance.
The programme does not start.
The appliance does not fill with wa‐
ter.
The display shows i10 or i11.
The appliance does not drain the
water.
The display shows i20.
• Make sure that the mains plug is connected to the mains socket.
• Make sure that there is no damaged fuse in the fuse box.
• Make sure that the appliance door is closed.
• If the delay start is set, cancel the setting or wait for the end of the
countdown.
• The appliance recharges the resin inside the water softener. The dura‐
tion of the procedure is approximately 5 minutes.
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not too low. For this
information, contact your local water authority.
• Make sure that the water tap is not clogged.
• Make sure that the filter in the inlet hose is not clogged.
• Make sure that the inlet hose has no kinks or bends.
• Make sure that the sink spigot is not clogged.
• Make sure that the interior filter system is not clogged.
• Make sure that the drain hose has no kinks or bends.
ENGLISH 27
Page 28
Problem and alarm code Possible cause and solution
The anti-flood device is on.
The display shows i30.
Malfunction of the water level detec‐
tion sensor.
The display shows i41 - i44.
Malfunction of the wash pump or the
drain pump.
The display shows i51 - i59 or i5A i5F.
The temperature of the water inside
the appliance is too high or malfunc‐
tion of the temperature sensor oc‐
curred.
The display shows i61 or i69.
Technical malfunction of the appli‐
ance.
The display shows iC0 or iC3.
The level of water inside the appli‐
ance is too high.
The display shows iF1.
Network unit error.
The display shows iC4 or iC5.
The appliance stops and starts
more times during operation.
The programme lasts too long.
The displayed programme duration
is different than the duration in the
consumption values table.
The remaining time in the display in‐
creases and skips nearly to the end
of the programme duration.
Small leak from the appliance door.
The appliance door is difficult to
close.
The appliance door opens during
the wash cycle.
• Close the water tap.
• Make sure that the appliance is correctly installed.
• Make sure the baskets are loaded as instructed in the user manual.
• Make sure that the filters are clean.
• Switch the appliance off and on.
• Switch the appliance off and on.
• Make sure that the temperature of the inlet water does not exceed
60°C.
• Switch the appliance off and on.
• Switch the appliance off and on.
• Switch the appliance off and on.
• Make sure that the filters are clean.
• Make sure that the outlet hose is installed at the right height above the
floor. Refer to the installation instructions.
• Contact an Authorised Service Centre.
• It is normal. It provides optimal cleaning results and energy savings.
• If the delay start option is set, cancel the delay setting or wait for the
end of the countdown.
• Activating options increases the programme duration.
• Refer to the consumption values table in the chapter "Programme se‐
lection".
• This is not a defect. The appliance is working correctly.
• The appliance is not levelled. Loosen or tighten the adjustable feet (if
applicable).
• The appliance door is not centred on the tub. Adjust the rear foot (if ap‐
plicable).
• The appliance is not levelled. Loosen or tighten the adjustable feet (if
applicable).
• Parts of the tableware are protruding from the baskets.
• The AirDry function is activated. You can deactivate the function. Refer
to "Basic settings".
28 ENGLISH
Page 29
Problem and alarm code Possible cause and solution
Rattling or knocking sounds from
the inside of the appliance.
The appliance trips the circuit-beak‐
er.
The appliance is switched on but
does not operate.
The display shows PF.
The appliance switches off during
operation.
The display shows upd. All buttons
are inactive except for the on/off
button.
• The tableware is not properly arranged in the baskets. Refer to basket
loading leaflet.
• Make sure that the spray arms can rotate freely.
• The amperage is insufficient to supply simultaneously all the applian‐
ces in use. Check the socket amperage and the capacity of the meter
or turn off one of the appliances in use.
• Internal electrical fault of the appliance. Contact an Authorised Service
Centre.
• Power supply is out of the operating range. The wash cycle is tempora‐
rily interrupted and resumes automatically once the power is restored.
• Complete power outage. The wash cycle is temporarily interrupted and
resumes automatically once the power is restored.
• The appliance downloads and installs the firmware update automatical‐
ly when it is available. The display shows upd for the duration of the
updating process. Wait for the process to be complete. If you interrupt
the update process by deactivating the appliance, it resumes when you
activate the appliance.
The firmware update does not change the appliance performance dec‐
laration values.
Once you have checked the appliance,
deactivate and activate the appliance. If the
problem occurs again, contact an Authorised
Service Centre.
For alarm codes not described in the table,
contact an Authorised Service Centre.
WARNING!
We do not recommend using the
appliance until the problem has been
completely fixed. Unplug the appliance
and do not plug it in again until you are
certain that it operates correctly.
13.1 The product number code (PNC)
If you contact an Authorised Service Centre,
you need to provide the product number code
of your appliance.
The PNC can be found on the rating plate on
the appliance door. You can also check the
PNC on the control panel.
Before checking the PNC, make sure the
appliance is in the programme selection.
1. Press and hold simultaneously and
for about 3 seconds.
The display shows the PNC of your
appliance.
2. To exit the PNC presentation, press and
hold simultaneously and for
about 3 seconds.
The appliance returns to the programme
selection.
ENGLISH 29
Page 30
13.2 The dishwashing and drying results are not satisfactory
Problem Possible cause and solution
Poor washing results.
Poor drying results.
There are whitish streaks or bluish lay‐
ers on glasses and dishes.
There are stains and dry water drops
on glasses and dishes.
The interior of the appliance is wet.
Unusual foam during washing.
Traces of rust on cutlery.
There are residues of detergent in the
dispenser at the end of the pro‐
gramme.
Odours inside the appliance.
• Refer to "Daily use", "Hints and tips" and the basket loading leaf‐
let.
• Use more intensive washing programme.
• Activate the ExtraPower option to improve the washing results of a
selected programme.
• Clean spray arm jets and filter. Refer to "Care and Cleaning".
• Tableware was left for too long inside the closed appliance. Activate
the function AirDry to set the automatic opening of the door and to
improve the drying performance.
• There is no rinse aid or the dosage of rinse aid is not sufficient. Fill
the rinse aid dispenser or set the dosage of rinse aid to a higher lev‐
el.
• The quality of the rinse aid can be the cause.
• Always use rinse aid, even with multi-tablets.
• Plastic items may need to be towel dried.
• The programme does not have the drying phase. Refer to "Pro‐
grammes overview".
• The released quantity of rinse aid is too high. Adjust the rinse aid
dosage to a lower level.
• The quantity of detergent is too high.
• The released quantity of rinse aid is not sufficient. Adjust the rinse
aid dosage to a higher level.
• The quality of the rinse aid can be the cause.
• This is not a defect of the appliance. Humidity condensates on the
appliance walls.
• Use the detergent designed specifically for dishwashers.
• Use a detergent from a different manufacturer.
• Do not pre-rinse dishes under running water.
• There is too much salt in the water used for washing. Refer to "The
water softener".
• Silver and stainless steel cutlery were placed together. Do not place
silver and stainless steel items close together.
• The detergent tablet was stuck in the dispenser and was not washed
away by water.
• Water cannot wash away the detergent from the dispenser. Make
sure that the spray arms are not blocked or clogged.
• Make sure that items in the baskets do not impede the lid of the de‐
tergent dispenser from opening.
• Refer to "Internal cleaning".
• Start the Machine Care programme with a descaler or a cleaning
product designed for dishwashers.
30 ENGLISH
Page 31
Problem Possible cause and solution
Limescale deposits on the tableware,
on the tub and on the inside of the
door.
Dull, discoloured or chipped table‐
ware.
• The level of salt is low, check the refill indicator.
• The cap of the salt container is loose.
• Your tap water is hard. Refer to "The water softener".
• Use salt and set regeneration of the water softener even when multifunctional tablets are used. Refer to "The water softener".
• Start the Machine Care programme with a descaler designed for
dishwashers.
• If limescale deposits persist, clean the appliance with the suitable de‐
tergents.
• Try a different detergent.
• Contact the detergent manufacturer.
• Make sure that only dishwasher-safe items are washed in the appli‐
ance.
• Load and unload the basket carefully. Refer to the basket loading
leaflet.
• Place delicate items in the upper basket.
• Activate the GlassCare option to ensure special care for glassware
and delicate items.
Refer to "Before first use", "Daily use",
or "Hints and tips" for other possible
causes.
13.3 Problems with wireless connection
Problem Possible cause and solution
Activating wireless connection is not
successful.
• Wrong wireless network ID or password. Cancel the setup and start
it again to enter the correct credentials. Refer to "Wireless connec‐
tion".
• There is a trouble with the wireless network signal. Check your wire‐
less network and router. Restart the router.
• The wireless network signal is weak. Move router closer to the dish‐
washer.
• The wireless signal is disrupted by a microwave appliance placed
near the dishwasher. Turn off the microwave appliance.
• Contact your wireless service provider if there are further problems
with the wireless network.
ENGLISH 31
Page 32
Problem Possible cause and solution
The app cannot connect to the dish‐
washer.
The app cannot connect to the dish‐
washer through any network other
than your home wireless network. The
indicator flashes.
The app frequently cannot connect to
the dishwasher.
• There is a trouble with the wireless network signal. Check your wire‐
less network and router. Restart the router.
• Check if your mobile device is connected to the network.
• New router was installed or router configuration was changed. Con‐
figure the dishwasher and mobile device again. Refer to "Wireless
connection".
• Contact your wireless service provider if there are further problems
with the wireless network.
• The connection to the cloud is lost. Wait for the connection to be re‐
stored.
• The wireless signal is disrupted by a microwave appliance placed
near the dishwasher. Turn off the microwave appliance. Avoid using
the microwave appliance and the remote start at the same time.
• The wireless network signal is weak. Move router as close to the
dishwasher as possible or consider purchasing a wireless range ex‐
tender.
14. TECHNICAL INFORMATION
Dimensions Width / height / depth (mm) 596 / 818 - 898 / 550
Electrical connection
Water supply pressure Min. / max. MPa (bar) 0.05 (0.5) / 1 (10)
Water supply
Capacity Place settings 14
1)
Refer to the rating plate for other values.
2)
If the hot water comes from alternative source of energy (e.g. solar panels), use the hot water supply to de‐
crease energy consumption.
1)
Voltage (V) 200 - 240
Frequency (Hz) 50 - 60
Cold water or hot water
2)
min. 5 - max. 60 °C
14.1 Link to the EU EPREL database
The QR code on the energy label supplied
with the appliance provides a web link to the
registration of this appliance in the EU
EPREL database. Keep the energy label for
reference together with the user manual and
all other documents provided with this
appliance.
It is possible to find information related to the
performance of the product in the EU EPREL
32 ENGLISH
database using the link https://
eprel.ec.europa.eu and the model name and
product number that you can find on the
rating plate of the appliance. Refer to the
chapter "Product description".
For more detailed information about the
energy label, visit www.theenergylabel.eu.
Page 33
15. ENVIRONMENTAL CONCERNS
Recycle materials with the symbol . Put the
packaging in relevant containers to recycle it.
Help protect the environment and human
health by recycling waste of electrical and
electronic appliances. Do not dispose of
appliances marked with the symbol with
the household waste. Return the product to
your local recycling facility or contact your
municipal office.
ENGLISH 33
*
Page 34
Page 35
Page 36
The software in this product contains components that are based on free and open source software. AEG gratefully
acknowledges the contributions of the open software and robotics communities to the development project.
To access the source code of these free and open source software components whose license conditions require
publishing, and to see their full copyright information and applicable license terms, please visit:
http://aeg.opensoftwarerepository.com (folder NIUS)
My AEG Kitchen app
117847842-A-472023
Loading...