AEG 79231KF-N User Manual

79231KF-N
User manual Ceramic glass hob Benutzerinformation Glaskeramik-Kochfeld Notice d'utilisation Table vitrocéramique Gebruiksaanwijzing Glaskeramische
kookplaat
Contents
2
Thank you for choosing one of our high-quality products.
To ensure optimal and regular performance of your appliance please read this instruction manual carefully. It will enable you to navigate all processes perfectly and most efficiently. To refer to this manual any time you need to, we recommend you to keep it in a safe plac e. An d p le as e pass it to any future owner of the appliance.
We wish you much joy with your new appliance.
Contents
Operating instructions 2
Safety instructions 2 Description of the appliance 4 Operating the appliance 6 Tips on cooking and frying 11 Care and cleaning 13
What to do if... 14 Disposal 15
Installation instructions 16
Installation instructions 16 Service 18
Subject to change without notice
Operating instructions
Safety instructions
WARNING!
Please comply with these instructions. If you do not, any damage resulting is not covered by the warranty.
Correct use
• This appliance is not intended for use by children or other persons whose physical, sensory or mental capabilities or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction by a responsible person to ensure that they can use the appliance safely.
• Do not leave the appliance unattended during operation.
• This appliance should be used only for normal domestic cooking and frying of food.
• The appliance must not be used as a work surface or as a storage surface
• Additions or modifications to the appliance are not permitted.
• Do not place or store flammable liquids, highly inflammable materials or fusible objects (e.g. plastic film, plastic, aluminium) on or near the appliance.
Children’s safety
• Small children must be kept away from the appliance.
• Only let bigger children work on the appliance under supervision.
Safety instructions
3
• To avoid small children and pets unintentionally switching the appliance on, we recom­mend activation of the child safety device.
General safety
• The appliance may only be installed and connected by trained, registered service engi­neers.
• Built-in appliances may only be used after they have built in to suitable built-in units and work surfaces that meet standards.
• In the event of faults with the appliance or damage to the glass ceramic (cracks, scratches or splits), the appliance must be switched off and disconnected from the electrical supply, to prevent the possibility of an electric shock.
• Repairs to the appliance must only be carried out by trained registered service engineers.
Safety during use
• Overheated fats and oils can ignite very quickly. Warning! Fire hazard!
• There is the risk of burns from the appliance if used carelessly.
• Remove stickers and film from the glass ceramic.
• Cables from electrical appliances must not touch the hot surface of the appliance or hot cookware.
• Switch the cooking zones off after each use.
• Risk of burns! Do not place objects made of metal, such as knives, forks, spoons and saucepan lids on the cooking surface, as they can get hot.
Safety when cleaning
• For cleaning, the appliance must be switched off and cooled down.
• For safety reasons, the cleaning of the appliance with steam jet or highpressure cleaning equipment is not permitted.
How to avoid damage to the appliance
• The glass ceramic can be damaged by objects falling onto it.
• The edge of the glass ceramic can be damaged by being knocked by the cookware.
• Cookware made of cast iron, cast aluminium or with damaged bottoms can scratch the glass ceramic if pushed across the surface.
• Objects that melt and things that boil over can burn onto the glass ceramic and should be removed straightaway.
• To avoid damaging cookware and glass ceramics, do not allow saucepans or frying pans to boil dry.
• Do not use the cooking zones with empty cookware or without cookware.
Description of the appliance
4
Description of the appliance
Cooking surface layout
1 2
1 Single zone 1200W 2 Double ring zone 700/1700W 3 Control panel 4 Single zone 1800W 5 Double ring zone 750/2200W 6 Control panel
Control panel layout
145 mm
120/210
mm
6 3
9
8
7
5 4
1 2 3
120/180
mm
180 mm
4
6
1 Timer display 2 Child lock with a pilot light 3 Stop+Go with a pilot light 4 On/Off with indicator 5 Double ring zone with pilot lights 6 Double ring zone with pilot lights
5
Description of the appliance
7 Heat setting indicator 8 Timer 9 Cooking zones indicator of Timer
Touch Control sensor fields
The appliance is operated using Touch Control sensor fields. Functions are controlled by touching sensor fields and confirmed by displays and acoustic signals. Only touch the sensor fields which activate a desired function. Do not cover other sensor fields.
If the control bar is touched for longer than 6 seconds, a signal sounds and the appliance switches itself off.
Sensor field Function
On / Off Switches appliance on and off Child lock Locking control panel for children Double ring To switch outer rings on and off STOP+GO To switch the Keep Warm setting on/ off Automatic warm-upTo switch the automatic warm-up function on and off
Timer Timer selection Increase settings To increase Timer time Reduce settings To reduce Timer time
5
Control bar
The heat setting and the power function are set via the control bar. The heat setting indi­cator consists of a chain of light elements.
6
5
6
4
1 Automatic warm-up function 2 Heat setting selection 3 Cooking zone Off 4 Operational readiness indicator for cooking zone 5 Heat setting indicators
1
2
3
Operating the appliance
6
6 Automatic warm-up indicator
If the control bar is touched for longer than 6 seconds, a signal sounds and the appliance switches itself off.
Displays
Display Description
The cooking zone is switched off
/
-
Keep Warm settings Keep Warm / STOP+GO function is switched on Heat settings To set heat settings Automatic Warm-up The Automatic Warm-up function is switched on Fault Malfunction has occurred Residual heat Cooking zone is still hot Child safety device Lock/Child safety device is set Automatic Switch off Switch off is active
Residual heat indicator
The residual heat indicator lights up, as soon as one cooking zone is hot.
WARNING!
Risk of burns from residual heat! After you switch the appliance off, the cooking zones need some time to cool down. Look at the residual heat indicator.
Use residual heat for melting and keeping food warm.
Operating the appliance
Switching the appliance on and off
Control panel Display Pilot light
Switch on Switch off
After switching on, within approx. 10 seconds a heat setting or a function must be set, otherwise the appliance automatically switches itself off.
Setting the heat setting
Control panel Display
To set the heat setting
Switch off
Touch for 1 second / Touch for 1 second / none
Touch the desired heat setting, if necessary, correct up or down
Touch
lights up. goes out.
/ to
Operating the appliance
Switching the outside ring on and off
By switching the outside rings on or off, the effective heating surface can be matched to the size of the cookware.
Before an outside ring can be switched on, the inside ring must be switched on
Double ring zone Sensor field Pilot light
To switch on outside ring To switch off outside ring
Touch for 1-2 seconds Touch for 1-2 seconds
Second pilot light lights up Second pilot light goes out
Locking/unlocking the control panel
The control panel, with the exception of the “On/Off” sensor field, can be locked at any time in order to prevent the settings being changed e.g. by wiping over the panel with a cloth.
Control panel Display
To switch on To switch off
Touch (for 4 seconds) Touch
previously set heat setting
When you switch the appliance off, the locking function is automatically switched off.
Turning the STOP+GO function on and off
The STOP+GO function simultaneously toggles all active cooking zones to keep-warm mode then back to the heat setting they were at before
Control panel Display
To switch on To switch off
Touch Touch
Previous heat setting (not automatic warm-up or power function)
7
STOP+GO does not stop timer functions.
STOP+GO controls the entire control panel apart from the sensor field .
Using the automatic warm-up function
All cooking zones are equipped with an automatic warm-up function. When setting a heat setting using the automatic warm-up function, the cooking zone switches to full power for a certain amount of time and then automatically switches back to the heat setting set.
Step Control Panel Display
1.
Touch
Operating the appliance
8
Step Control Panel Display
2. Move your finger down from
to select the de-
sired heat setting between
and
/ after 5 seconds . As long as is displayed, the appliance works at full power. After the automatic warm up is completed, the heat setting
/ is displayed again.
The length of time that the automatic warm up function operates depends on the heat setting selected.
Heat setting Length of the automatic warm up [min:sec]
1:00 1:40 2:40 4:50 5:30 6:30
8:10 10:10 12:20
2:30
2:30
3:30
4:30
---
Using the child safety device
The child safety device prevents unintentional use of the appliance.
Switching on the child safety device
Step Control panel Display/Signal
1.
2. The child safety device is switched on.
Switching off the child safety device
Step Control panel Display/Signal
1.
2.
3.
Switch on appliance. Do not set a heat setting.
Touch for 4 seconds
Switch on appliance. Do not set a heat setting.
Touch for 4 seconds lights up
Switch appliance off.
00
00
Operating the appliance
Step Control panel Display/Signal
The child safety device is switched off.
The child safety device can only be switched on and off if no heat setting is set.
Overriding the child safety device
The child safety device can be switched off in this way for a single cooking session; it remains activated afterwards.
Step Control panel Display/Signal
1.
2. Until the appliance is next switched off, it can used as normal. After switching off the appliance,
the child safety device is active again.
Switch appliance on
Touch for 4 seconds lights up
After overriding the child safety device, a heat setting or a function must be set within approx. 10 seconds, otherwise the appliance automatically switches itself off.
Using the timer
Function Condition Outcome after the time has
Automatic cut-out a heat setting is set acoustic signal
Cooking zone switches off
Countdown timer cooking zones not in use acoustic signal
elapsed
flashes
flashes
9
If just one countdown value is set you can change it only when the appliance is switched on.
If a heat setting is set on this cooking zone in addition to a countdown timer, the cooking zone is switched off after the time set has elapsed.
If a cooking zone is switched off, the timer function set is also switched off.
Selecting a cooking zone
Step Control panel Display
1.
2.
3.
Touch once
Touch once
Touch once
Pilot light of the first cooking zone flashes
Pilot light of the second cooking zone flashes
Pilot light of the third cooking zone flashes
0
Operating the appliance
10
Step Control panel Display
4.
Touch once
Pilot light of the fourth cooking zone flashes
If other timer functions are set, after a few seconds the shortest remaining time of all the timer functions is displayed and the corresponding pilot light flashes.
Setting the time
Step Control panel Display
1.
2. After a few seconds the pilot light flashes more slowly.
The time is set. The time counts down.
Select a cooking zone
Touch or
Pilot light for the cooking zone selected flashes
to 99 minutes
00
Switching off the timer function
Step Control panel Display
1.
2. The pilot light goes out.
The Timer function for the selected cooking zone is switched off.
Select a cooking zone
Touch The time remaining counts backwards to 00 .
Pilot light of cooking zone selected flashes faster Time remaining is displayed
Changing the time
Step Control panel Display
1.
2. After a few seconds the pilot light flashes more slowly.
The time is set. The time counts down.
Select a cooking zone
Touch or
Pilot light of the selected cooking zone flashes more quickly Remaining time is displayed
to 99 minutes
1
Displaying the time remaining for a cooking zone
Step Control panel field Display
1.
After a few seconds the pilot light flashes more slowly.
Select a cooking zone
Pilot light of the cooking zone selected flashes faster The time remaining is displayed
Switching off the acoustic signal
Step Control panel field Acoustic signal
1.
Touch
Acoustic signal to acknowledge.
Tips on cooking and frying
Step Control panel field Acoustic signal
Acoustic signal stops.
Automatic switch off
Cooking surface
• If after switching on the cooking surface, a heat setting is not set for a cooking zone within approx. 10 seconds, the cooking surface automatically switches itself off.
• If one or more sensor fields are covered by objects (a pan, etc.) for longer than approx. 10 seconds, a signal sounds and the cooking surface switches off automatically.
• If all cooking zones are switched off, the cooking surface automatically switches itself off after approx. 10 seconds.
Control panel
• When the appliance is switched off, if one or more of the sensor fields on the control panel are covered for more than 10 seconds, an acoustic signal sounds. The acoustic signal switches itself off automatically when the sensor fields are no longer covered.
Cooking zones
• If one of the cooking zones is not switched off after a certain time, or if the heat setting is not modified, the relevant cooking zone switches off automatically. Before being used again, the cooking zone must be set to
Heat setting Switches off after
-
-
-
-
.
6 hours 5 hours 4 hours
1.5 hours
11
is displayed.
Tips on cooking and frying
Information about acrylamides
According to the latest scientific research, intensive browning of food, especially in products containing starch, may present a health risk due to acrylamide. Therefore we recommend cooking at low temperatures and not browning foods too much.
Cookware
• You can recognise good cookware from the bottoms of the pans. The bottom should be as thick and flat as possible.
• Cookware made of enamelled steel or with aluminium or copper bottoms can leave discolorations on the glass ceramic surface which are difficult or impossible to remove.
Tips on cooking and frying
12
Energy saving
Always place cookware on the cooking zone before it is switched on.
If possible, always place lids on the pans.
Switch cooking zones off before the end of the cooking time, to take advantage of residual heat.
Bottom of pans and cooking zones should be the same size.
Examples of cooking applications
The information given in the following table is for guidance only.
Heat set-
ting
0 Off position
1
1-3 Melting Hollandaise sauce,
1-3 Solidifying Fluffy omelettes,
3-5 Simmering Simmering rice and
Cooking process suitable for Cook time Tips/Hints
Keeping food warm Keeping cooked
foods warm
melting butter, chocolate, gelatine
baked eggs
milkbased dishes Heating up ready­cooked meals
as required Cover
5-25 mins. Stir occasionally
10-40 mins. Cook with lid on
25-50 mins. Add at least twice
as much liquid as rice, stir milk dishes part way through cooking
Care and cleaning
13
Heat set-
ting
5-7 Steaming
7-9 Boiling Steaming potatoes 20-60 mins. Use only a little liq-
7-9 Boiling Cooking larger
9-12 Gentle frying Frying escalope,
12-13 Heavy frying Hash browns, loin
14 Boiling Searing
Cooking process suitable for Cook time Tips/Hints
Braising
Deep frying
Steaming vegeta­bles, fish Braising meat
quantities of food, stews and soups
veal cordon bleu, cutlets, rissoles, sausages, liver, roux, eggs, pan­cakes, doughnuts
steaks, steaks, Flä­dle (pancakes for garnishing soup)
Boiling large quantities of water, cooking pasta, searing meat (goulash, pot roast), deep frying chips
20-45 mins. With vegetables
add only a little liq­uid (a few table­spoons)
uid, e. g.: max. ¼ l water for 750 g of potatoes
60-150 mins. Up to 3 l liquid plus
ingredients
as required Turn halfway
through cooking
5-15 mins. per pan Turn halfway
through cooking
Care and cleaning
WARNING!
Risk of burns from residual heat.
WARNING!
Sharp objects and abrasive cleaning materials will damage the appliance. Clean with water and washing up liquid.
WARNING!
Residues from cleaning agents will damage the appliance. Remove residues with water and washing up liquid.
Cleaning the appliance after each use
1. Wipe the appliance with a damp cloth and a little washing up liquid.
2. Rub the appliance dry using a clean cloth.
Removing deposits
1. Place a scraper on the glass ceramic surface at an angle.
2. Remove residues by sliding the blade over the surface.
3. Wipe the appliance with a damp cloth and a little washing up liquid.
What to do if...
14
4. Rub the appliance dry using a clean cloth.
Remove
Type of dirt immediately when the appliance has
sugar, food containing sugar
plastics, tin foil yes --- a scraper * limescale and water
rings fat splashes --- yes cleaner for glass ceramic
shiny metallic discol­oration
yes --- a scraper *
--- yes cleaner for glass ceramic
--- yes cleaner for glass ceramic
cooled down
using
or stainless steel *
or stainless steel *
or stainless steel *
* Scrapers and cleaners for glass ceramic and stainless steel can be purchased in specialist shops
Remove stubborn residues with a cleaner for glass ceramic or stainless steel.
Scratches or dark stains on the glass ceramic that cannot be removed do not however affect the functioning of the appliance.
What to do if...
Problem Possible cause Remedy
The cooking zones will not switch on or are not function­ing
The child safety device is
Several sensor fields were
Automatic switch off has been
There is water on the control
Acoustic signal sounds when appliance is switched off
More than 10 seconds have passed since the appliance was switched on
switched on
touched at the same time
triggered
panel, or the control panel is covered with splashes
is active - Switch off
The control panel is wholly or partly covered by objects.
Switch the appliance on again.
Deactivate child safety device (See the section “Child safety device”)
Only touch one sensor field
Remove any objects (pan, cloths, etc.) that are lying on the control panel. Switch the appliance on again
Wipe the control panel
Remove objects.
Disposal
Problem Possible cause Remedy
The residual heat indicator is not displaying anything
The automatic warm up func­tion is not switching itself on
The highest heat setting is set The highest heat setting has
Acoustic signal sounds and ap­pliance switches itself on and then off again; after 5 seconds another acoustic signal sounds
is lit
and number are displayed
The cooking zone was only on for a short time and is therefore not hot
There is still residual heat on the cooking zone
The On/Off sensor field has been covered up, e.g. by a cloth
Overheating protection for the cooking zone has been trig­gered
Electronics fault Disconnect the appliance from
If the cooking zone is supposed to be hot, call the Customer Service Department.
Let the cooking zone cool down
the same power as the auto­matic warm up function
Do not place any objects on the control panel
Switch off the cooking zone. Switch the cooking zone on again
the electrical supply for a few minutes (Take the fuse out of the house’s wiring system) If
after switching on again, displayed again, call the cus­tomer service department
15
is
If you are unable to remedy the problem by following the above suggestions, please contact your dealer or the Customer Care Department.
WARNING!
Repairs to the appliance are only to be carried out by qualified service engineers. Consid­erable danger to the user may result from improper repairs.
If the appliance has been wrongly operated, the visit from the customer service technician or dealer may not take place free of charge, even during the warranty period.
Disposal
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product.
Installation instructions
16
Installation instructions
Installation instructions
WARNING!
This must be read! The laws, ordinances, directives and standards in force in the country of use are to be followed (safety regulations, proper recycling in accordance with the regulations, etc.) Installation may only be carried out by a qualified electrician. The minimum distances to other appliances and units are to be observed. Anti-shock protection must be provided by the installation, for example drawers may only be installed with a protective floor directly underneath the appliance. The cut surfaces of the worktop are to be protected against moisture using a suitable sealant. The sealant seals the appliance to the work top with no gap. When building in, protect the underside of the appliance from steam and moisture, e.g. from a dishwasher or oven. Avoid installing the appliance next to doors and under windows. Otherwise hot cookware may be knocked off the rings when doors and windows are opened.
WARNING!
Risk of injury from electrical current.
• The electrical mains terminal is live.
• Make electrical mains terminal free of voltage.
• Follow connection schematic.
• Observe electrical safety rules.
• Ensure anti-shock protection by installing correctly.
• The appliance must be connected to the electrical supply by a qualified electrician.
• Loose and inappropriate plug and socket connections can make the terminal overheat.
• Have the clamping connections correctly installed by a qualified electrician.
• Use strain relief clamp on cable.
• In the event of single-phase or two-phase connection, the appropriate mains cable of type H05BB-F Tmax 90°C (or higher) must be used.
• If this appliance’s mains cable is damaged, it must be replaced by a special cable (type H05BB-F Tmax 90°C; or higher). Please contact your local Service Force Center for further advice.
A device must be provided in the electrical installation which allows the appliance to be disconnected from the mains at all poles with a contact opening width of at least 3 mm Suitable isolation devices include line protecting cut-outs, fuses (screw type fuses are to be removed from the holder), earth leakage trips and contactors.
Sticking on the seal
• Clean the worktop in the area of the cut-out section.
• Stick the one-sided self-adhesive sealing tape supplied all the way round the lower edge of the cooking surface along the outer edge of the glass ceramic panel. Do not stretch it. The cut ends should lie in the middle of one side. When you have cut it to length (add a few mm), press the two ends flush up against one another.
Assembly
min. 500mm
min. 50mm
Installation instructions
17
1
2
600
=
490 +1
R5
=
680 +1
Service
18
Rating plate
79231KF-N
55HDD62AO
AEG-ELECTROLUX
949593181
7,0 kW
Service
In the event of technical faults, please first check whether you can remedy the problem yourself with the help of the operating instructions (section “What to do if…”). If you were not able to remedy the problem yourself, please contact the Customer Care Department or one of our service partners. In order to be able to assist you quickly, we require the following information: – Three-digit-letter combination
for glass ceramic
– Model description – Product number (PNC) – Serial number
(S No. - see the rating plate)
– Type of fault – Any error messages displayed by
the appliance
Danke, dass Sie sich für eines unserer hochqualitativen Produkte entschieden haben.
Lesen Sie für eine optimale und gleichmäßige Leistung Ihres Gerätes diese Benutzerinformation bitte sorgfältig durch. Sie wird Ihnen helfen, alle Vorgänge perfekt und äußerst effizient zu steuern. Damit Sie diese Benutzerinformation bei Bedarf stets zur Hand haben, empfehlen wir Ihnen, sie an einem sicheren Ort aufzubewahren. Und geben Sie diese Benutzerinformation bitte an einen eventuellen neuen Besitzer dieses Gerätes weiter.
Wir wünschen Ihnen viel Freude mit Ihrem neuen Gerät.
Inhalt
Inhalt
19
Gebrauchsanweisung 19
Sicherheitshinweise 19 Gerätebeschreibung 21 Bedienung des Geräts 23 Tipps zum Kochen und Braten 28 Reinigung und Pflege 30
Gebrauchsanweisung
Sicherheitshinweise
WARNUNG!
Bitte halten Sie sich an die vorliegenden Anweisungen. Andernfalls entfällt bei auftretenden Schäden der Garantieanspruch.
Bestimmungsgemäße Verwendung
• Personen (einschließlich Kinder), die aufgrund ihrer physischen, sensorischen oder geis­tigen Fähigkeiten oder ihrer Unerfahrenheit oder Unkenntnis nicht in der Lage sind, das Gerät sicher zu benutzen, sollten dieses Gerät nicht ohne Aufsicht oder Anweisung durch eine verantwortliche Person benutzen.
• Lassen Sie das Gerät bei Betrieb nicht unbeaufsichtigt.
• Dieses Gerät darf nur für das haushaltsübliche Kochen und Braten von Speisen verwendet werden.
• Das Gerät darf nicht als Arbeits- oder Abstellfläche verwendet werden
• Umbauten oder Veränderungen am Gerät sind nicht zulässig.
• Brennbare Flüssigkeiten, leicht entzündliche Materialien oder schmelzbare Gegenstände (z.B. Folien, Kunststoff, Aluminium) nicht auf dem Gerät oder in dessen Nähe abstellen oder lagern
892930240-00-112008
Was tun, wenn... 31 Entsorgung 32
Montageanweisung 33
Aufstellanweisung 33 Kundendienst 35
Änderungen vorbehalten
Sicherheitshinweise
20
Sicherheit für Kinder
• Kleinkinder grundsätzlich vom Gerät fernhalten.
• Größere Kinder nur unter Anleitung und Aufsicht am Gerät arbeiten lassen.
• Um ein unbeabsichtigtes Einschalten durch Kleinkinder und Haustiere zu verhindern, empfehlen wir, die Kindersicherung zu aktivieren.
Allgemeine Sicherheit
• Montage und Anschluss des Gerätes dürfen nur durch ausgebildete und autorisierte Fachkräfte vorgenommen werden.
• Einbaugeräte dürfen nur nach dem Einbau in normgerechte, passende Einbauschränke und Arbeitsplatten betrieben werden.
• Bei Störungen am Gerät oder bei Schäden an der Glaskeramik (Sprünge, Brüche bzw. Risse) muss das Gerät ausgeschaltet und von der Netzversorgung getrennt werden, um einen möglichen elektrischen Schlag zu vermeiden.
• Reparaturen am Gerät dürfen nur von ausgebildeten und autorisierten Fachkräften durchgeführt werden.
Sicherheit während der Benutzung
• Überhitzte Fette und Öle entzünden sich sehr schnell. Warnung! Brandgefahr!
• Am Gerät besteht beim unachtsamen Arbeiten Verbrennungsgefahr.
• Aufkleber und Folien von der Glaskeramik entfernen.
• Kabel von Elektrogeräten dürfen nicht an die heiße Geräteoberfläche bzw. heißes Koch­geschirr gelangen.
• Schalten Sie nach jedem Gebrauch die Kochzonen aus.
• Verbrennungsgefahr! Legen Sie keine Metallgegenstände wie Messer, Gabeln, Löffel oder Deckel auf die Oberfläche des Kochfelds, da diese heiß werden können.
Sicherheit beim Reinigen
• Zum Reinigen muss das Gerät ausgeschaltet und abgekühlt sein.
• Die Reinigung des Gerätes mit einem Dampfstrahl- oder Hochdruckreiniger ist aus Si­cherheitsgründen nicht zugelassen.
Vermeidung von Schäden am Gerät
• Die Glaskeramik kann durch herabfallende Gegenstände beschädigt werden.
• Stöße mit dem Kochgeschirr können den Rand der Glaskeramik beschädigen.
• Kochgeschirr aus Gusseisen, Aluguss oder mit beschädigten Böden können beim Ver­schieben die Glaskeramik verkratzen.
• Schmelzbare Gegenstände und Überkochendes können auf der Glaskeramik einbrennen und sollten sofort entfernt werden.
• Das Leerkochen von Töpfen und Pfannen vermeiden. Es kann Beschädigungen am Koch­geschirr oder der Glaskeramik verursachen.
• Die Kochzonen nicht mit leerem oder ohne Kochgeschirr benutzen.
Gerätebeschreibung
Ausstattung Kochfeld
1 2
Gerätebeschreibung
21
1 Einkreis-Kochzone 1.200 W 2 Zweikreis-Kochzone 700/1.700 W 3 Bedienfeld 4 Einkreis-Kochzone 1.800 W 5 Zweikreis-Kochzone 750/2.200 W 6 Bedienfeld
Ausstattung Bedienfeld
145 mm
120/210
mm
6 3
9
8
7
5 4
1 2 3
120/180
mm
180 mm
4
6
1 Timer-Anzeige 2 Kindersicherung mit Kontrolllampe 3 Stop+Go mit Kontrolllampe 4 Ein/Aus mit Anzeige 5 Zweikreis-Kochzone mit Kontrolllampen 6 Zweikreis-Kochzone mit Kontrolllampen
5
Gerätebeschreibung
22
7 Kochstufenanzeige 8 Timer 9 Kochzonen-Anzeige Timer-Funktion
Touch Control-Sensorfelder
Das Gerät wird mit Touch Control-Sensorfeldern bedient. Funktionen werden durch Be­rühren der Sensorfelder gesteuert und von Anzeigen und akustische Signalen bestätigt. Berühren Sie nur die Sensorfelder, welche die gewünschte Funktion aktivieren. Decken Sie andere Sensorfelder nicht ab.
Wird die Bedienleiste länger als 6 Sekunden berührt, ertönt ein akustisches Signal und das Gerät schaltet sich ab.
Sensorfeld Funktion
Ein/Aus Gerät ein- und ausschalten Kindersicherung Bedienfeld für Kinder sperren Zweikreis Äußere Heizkreise ein- und ausschalten STOP+GO Warmhaltestufe ein-/ausschalten Ankoch-Automatik Ankoch-Automatik einschalten/ausschalten Timer Timer Auswahl Einstellungen er-
höhen Einstellungen ver-
ringern
Timer-Zeit erhöhen
Timer-Zeit verringern
Bedienleiste
Die Kochstufe und die Power-Funktion werden über die Bedienleiste eingestellt. Die Koch­stufenanzeige besteht aus einer Reihe von Leuchtelementen.
6
5
6
4
1 Ankoch-Automatik 2 Kochstufenauswahl 3 Kochzone Aus 4 Bereitschaftsanzeige Kochzone
1
2
3
Bedienung des Geräts
5 Kochstufenanzeige 6 Anzeige Ankoch-Automatik
Wird die Bedienleiste länger als 6 Sekunden berührt, ertönt ein akustisches Signal und das Gerät schaltet sich ab.
Anzeigen
Anzeige Beschreibung
Kochzone ist ausgeschaltet
/
-
Warmhaltestufe WarmhaltestufeSTOP+GO-Funktion ist einge-
Kochstufen Kochstufen einstellen Ankoch-Automatik Ankoch-Automatik ist aktiv Fehler Fehlfunktion ist aufgetreten Restwärme Kochzone ist noch warm Kindersicherung Verriegelung/Kindersicherung ist eingeschaltet automatische Abschal-
tung
schaltet
Abschaltung ist aktiv
Restwärmeanzeige
Die Restwärmeanzeige leuchtet auf, sobald eine Kochzone heiß ist.
WARNUNG!
Verbrennungsgefahr durch Restwärme! Nach dem Ausschalten des Gerätes benötigen die Kochzonen eine gewisse Zeit zum Abkühlen. Restwärmeanzeige beachten.
23
Restwärme kann zum Schmelzen und Warmhalten von Speisen genutzt werden.
Bedienung des Geräts
Gerät ein- und ausschalten
Bedienfeld Anzeige Kontrolllampe
Einschalten Ausschalten
1 Sekunde berühren / 1 Sekunde berühren / keine
Nach dem Einschalten muss innerhalb von ca. 10 Sekunden eine Kochstufe oder eine Funk­tion eingestellt werden, sonst schaltet sich das Gerät automatisch aus
leuchtet. erlischt.
Loading...
+ 53 hidden pages