ADTRAN Total Access 4303 System Control Unit Quick Start Guide

Quick Start Technical Support (800) 726-8663 61200334L1-13B

October 2001

TOTAL ACCESS® 4303 SYSTEM CONTROLLER UNIT (SCU)

CLEI: SLC1LSZE_ _

SCU

1200334L1

ONLINE

ACTIVE

LINK

ALARM

ACO

C R A F T

FACEPLATE LEDS

ONLINE LED Descr ipti on

Off Blown fuse Green Online Blinking Green Offline Red Card failure Blinking Red Self-test failure Amber Self-test in progress Blinking Amber Module update in progress

ACTIVE LED Description

Green Active SCU Blinking Green Standby SCU - redundancy enabled Blinking Red Standby SCU - cannot automatically become

the active SCU while the current active SCU is installed

LINK LED Description

Off E the rnet link not detected Green Ethernet link detected

ALARM LED Description

Off N o s ystem alarms active Red Syste m al arm(s) activ e

ACO LED Description

Off ACO switch/ACO external input has not been

asserted

Green ACO switch and/or ACO external input has

been asserted

INSTALLATION INFORMATION

• Insert the module into either the slot labeled SCU-A or SCU-B.

• Connect a VT100 terminal configured for 9600 band (8N1) to the female DB-9 craft port on the front of the SCU.

• After the SCU has booted, the LOGIN prompt will appear on the VT100 terminal (if connected to the active SCU). Otherwise, a message indicating connection to the Standby SCU will b e displayed if the VT100 terminal is so connected.

• Menu access to the Active SCU is also available through the Admin port located on the backplane (J10).

• To configure the Ethernet port, us e the arrow keys and Enter key to navigate the following path:

SystemConfig/EthernetPort

SPECIFICATIONS

Menu Access VT100/Telnet Ethernet 10/100 Base T GR-303 Sw itch

Lucent and Nortel

Types Compliance FCC Part 15, UL 60950, NEBS Level 3 Temperature Operation: 0°C to 50°C

Storage: –40°C to 70°C

Relative Humidity To 95% noncondensing Power 18 watts Warranty 10 years

Quick Start Technical Support 888 (4ADTRAN) 61200334L1-13B

October 2001

TOTAL ACCESS® 4303 SYSTEM CONTROLLER UNIT (SCU)

MENU NAVIGATION AND SESSION MANAGEMENT

Description Key(s)

Return to home screen H Jump to alternate page J Select Arrow keys Edit/Descend Enter Cancel edit ESC Left/Right pane Tab Page up A Page down Z Ascend Backspace/ESC Return to home screen H Logout Ctrl+L Secure Ctrl+S Refresh display Ctrl+R Show extended data on/off Ctr l+V Factory default selection F Copy selected item C Paste from clipboard P Paste incremented value > Paste decremented value < Insert new list item I Delete list item D Navigation help Ctrl+Z Context specific help Ctrl+A

TOP LEVEL MENU INFORMATION

System Info

The System Info menu provides basic information about the unit as well as data fields for editing information.

System Status

The System Status menu provides information on the general status of the unit.

System Configuration

The System Configuration menu allow s the user to set the Total Access 4303 operational configuration parameters.

System Utility

The System Utility menu allows the user to view and set the system level parameters that pertain to upgrading, restoring, and testing the unit.

Modules

The Modules menu provides options that allow the user to configure, test, and view status of the installed option modules as well as the SCU.

Router

The router menu provides options that allow the user to define, configure, and monitor all Tota l Access 430 3 rou ter functions.

Dedicated Maps

The Dedicated Maps menu assigns dedicated cross c onnects between any two ports in the unit.

GR-303 RT

The GR-303 RT menu allows the user to configure the GR 303 capabilities of the un it. This includes creatin g both switc h and dropside DSXs and their appropriate settings.