Wall mount Installation Steps
To install the SDX810-AP, refer to Figure 4 and
complete the following steps.
NOTE
Do not mount the SDX810-AP above three meters
from the floor.
Wall Mount Installation
To wall mount the SDX810-AP, complete the
following steps:
Refer to Figure 4 when installing the SDX810-AP
on a wall.
1. Determine a location for the SDX810-AP.
Figure 4. Wall Mount Keyholes
2. Use the key holes on the back of the
SDX810-AP as a template and install two #6
drywall anchors.
3. Install two Ø3.5*30L Pan Head screws.Leave
approximately 1/4-inch (0.6 cm) protruding
from the mounting surface. Refer to Figure 5.
or
Figure 5. Place Ø3.5*30L Screws
4. Slide the SDX810-AP over the Pan Head
screws and exert a small amount of
downward pressure to ensure that the top of
the slots are resting on the shafts of the Pan
Head screws.
f
SDX810-AP
Shared Review 1
Safety and Regulatory Notice
Safety and Regulatory Notice
Sécurité et Avis de réglementation
Sécurité et Avis de réglementation
English Français
Mesh Access Point
April 2018
61287860F1-17A
P/N: 1287860F1
f WARNING!
■ Read all warnings and cautions before installing or servicing
this equipment.
■ Refer to the national, state and local electrical codes for the
requirements for power and grounding wiring methods.
CAUTION!
This equipment contains no parts that can be serviced by the
user.
g NOTE
■ This product meets EU RoHS Directive. Refer to
www.adtran.com for further information on RoHS/WEEE.
■ This device has been certified for use in Canada under
Industry Canada (IC) Radio Standards Specification (RSS)
RSS-247 and RSS-Gen. This Class B digital apparatus
complies with Canadian ICES-003.
This device complies with Industry Canada license-exempt
RSS standard(s). Operation is subject to the following two
conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including
interference that may cause undesired operation of the
device
■ Digital apparatus CAN ICES-3 (B)/NMB-3(B)
■ Radiation Exposure
This equipment complies with IC RSS-102 radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum
distance 20 cm between the radiator & your body.
■ This device is restricted to indoor use.
■ This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including
interference that may cause undesired operation of the
device.
f AVERTISSMENT!
■ Lisez tous les avertissements et mises en garde avant
l’installation de cet équipement ou la réalisation de toute
opération de maintenance.
■ Consultez les normes nationales, régionales et locales sur les
installations électriques pour connaître les exigences en
matière de câblage pour l’alimentation et la mise à la terre.
f ATTENTION!
Il n’existe aucune pièce pouvant être réparée par l’utilisateur à
l’intérieur de cet équipement.
g REMARQUE
■ Ce produit est conforme à la directive européenne RoHS.
Reportez-vous à
renseignements sur RoHS.
■ Cet appareil a été certifié pour utilisation au Canada en vertu
des spécifications de normes radio (RSS) d'Industrie Canada
(IC) RSS-247 et RSS-Gen. Cet appareil numérique de classe
B est conforme à la norme canadienne ICES-003.
Cet appareil est conforme aux normes RSS exemptes de
licence d'Industrie Canada. L'opération est soumise aux deux
conditions suivantes
1. Cet appareil ne peut pas causer d'interférences, et
2. Cet appareil doit accepter toute interférence, y compris les
interférences susceptibles de provoquer un fonctionnement
indésirable de l'appareil.
■ Appareil numérique CAN ICES-3 (B)/NMB-3(B)
■ Exposition aux radiations
Cet équipement est conforme aux limites d'exposition aux
rayonnements IC RSS-102 établies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé avec
un minimum de 20cm de distance entre la source de
rayonnement et votre corps.
■ Cet appareil est limité à une utilisation en intérieur.
www.adtran.com pour de plus amples
English Français
Shared Review 1
■ This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
♦ Reorient or relocate the receiving antenna.
♦ Increase the separation between the equipment and
receiver.
♦ Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
♦ Consult the dealer or experienced radio/TV technician for
help.
■ To satisfy FCC RF Exposure requirements for mobile and
base station transmission devices, a separation distance of
20 cm or more should be maintained between the antenna of
this device and persons during operation. To ensure
compliance, operation at closer than this distance is not
recommended. The antenna(s) used for this transmitter must
not be co-located or operating in conjunction with any other
antenna or transmitter.
■ Changes or modifications not expressly approved by
ADTRAN could void the user’s authority to operate this
equipment.
■ This product is designed to operate with a nominal operating
voltage of 12 VDC.
■ The product is supplied with a power adapter, which operates
from a main power source input of 100 - 240 V, 50/60 Hz, with
a nominal output of 12 VDC.
©2018 ADTRAN, Inc. All Rights Reserved.
CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
ADTRAN CUSTOMER CARE:
From within the U.S. 1.800.726.8663
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61287860F1-17A*
Loading...