ADTRAN Power Supply-Battery Charger User Manual

JOBAID

61175044L2-22A

0002

AC/DC POWER SUPPLY AND BATTERY CHARGER

STATUS LEDS

AC Power Operation (AC power only) Battery Operation (AC power supply or battery backup)

● GREEN OK ● GREEN OK (charging)

● YELLOW Power Fail ● YELLOW Discharging

● RED Power Fail ● RED Low (<40 V)

●● OFF Power Fail ●● OFF Disconnected

RELAYS

Alarm Relay

■ Provided for customer use

Condition Alarm Relay

Normal Open

AC Power Failure/ Cycles open/closed once per second if AC voltage <88 Vrms at Battery Backup engaged full load and battery backup is connected

Battery voltage <45V Stays closed if voltage <45 VDC to indicate that battery is

becoming depleted

Battery Disconnect Relay

■ Disconnects battery pack from the system if the battery voltage falls below 40 VDC

■ Prevents damage to batteries

CIRCUIT BREAKER

■ 3-amp circuit breaker

■ Protects unit from over-current

■ Rocker button extends out from front panel when tripped

■ Reset by pushing in on the rocker button

GROUNDING

■ 18 AWG or larger ground wire recommended to connect additional

ground connector to 'ground bus' in customer equipment room

AC/DC POWER

SUPPLY AND

BATTERY CHARGER

CLEI:SIMPAAAARA

■ For a complete I&M Practice: 877.457.5007, Document # 422. Please have fax number available. ■

MOUNTING INSTRUCTIONS

Remove the TA 750/850 AC Power Supply (ADTRAN part # 1175043LX) from the box and inspect for damage. If damage is apparent, contact your carrier or supplier.

Place the power supply with the power cord oriented downward.

Use four #6 x 3/8" machine screws (supplied) to mount the power supply to either side of the TA 750/850 shelf.

Note: Threaded mounting holes are provided on both sides of

the shelf.

Note: For battery backup installations, it is recommended to

mount the power supply on the left side of the TA 750/850 shelf, next to the battery cover hinge.

Note: Alternatively, the power supply can be mounted to the

backboard with four #6 x 1" wood screws (not supplied).

The device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by ADTRAN could void the user’s authority to operate this equipment.

WARRANTY

Warranty for Carrier Network products manufactured by ADTRAN and supplied under Buyer’s order for use in the U.S. is ten (10) years. For a complete copy of ADTRAN’s U.S. Carrier Network Equipment Warranty: (877) 457-5007, Document 414.

ELECTRICAL SPECIFICATIONS

■ AC input: 115 V nominal

■ Range: 90 to 132 VAC

■ DC output: -54 V, 60 W average, 100 W

peak

■ Battery charging: 16 hr nominal, 24 hr

maximum

■ Battery discharge: Up to 8 hours

Code Input Output

IC F C TC — — PC R —

TELECOMMUNICATIONS CODES

C A U T I O N !

SUBJECT TO ELECTROSTATIC DAMAGE

OR DECREASE IN RELIABILITY.

HANDLING PRECAUTIONS REQUIRED.

JOBAID

BACKUP BATTERY PACK

BACKUP

BATTERY

PAC K

CLEI:SIMPBBBARA

MAINTENANCE

■ Life expectancy: 3-5 years on standby use

■ Battery performance is adversely affected by extreme temperatures.

■ Old batteries should be recycled.

BATTERY SPECIFICATIONS

■ Batteries: 7 Amp/hr (4 batteries per pack)

■ Case size: 6”W x 3 3/4”H x 2 1/2”D

■ Battery type: Lead acid

■ Voltage: -54 VDC

■ Backup Time: Up to 8 hours

■ Wire Gauge: 18 AWG

■ Preferred Temperature: 68º F (20º C)

PRICING AND AVAILABILITY 800.827.0807

TECHNICAL SUPPORT 888.4ADTRAN

RETURN FOR REPAIR 256.963.8722

■ For a complete I&M Practice: 877.457.5007, Document # 423. Please have fax number available. ■

MOUNTING INSTRUCTIONS

Unpack the TA 750/850 Battery Backup system and inspect for damage. If damage is apparent, refer to your carrier or supplier for remedy.

Note: It is not necessary to remove the batteries during

installation process.

The battery box must be mounted with the following minimum clearances:

Top – 9" Bottom – 5" Left Side – 5" Right Side – 2"

Using the template provided,mark and drill three pilot holes for #10 mounting screws.

Insert #10 x 3/4" flat-head wood screws (supplied)

into the three pilot holes, leaving 1/16" space

between the screw-head and the backboard.

CAUTION: Fully loaded Battery box weighs 30 lbs.

Mount the battery box on the three support screws on the backboard.

Remove the two closure screws on the battery box and open the cover.

Use a long shaft screwdriver to tighten the three support screws.

WARRANTY

Warranty for Carrier Network products manufactured by ADTRAN and supplied under Buyer’s order for use in the U.S. is ten (10) years, except for batteries which carry manufacturer’s warranty. For a complete copy of ADTRAN’s U.S. Carrier Network Equipment Warranty: (877) 457-5007, Document 414.

C A U T I O N !

SUBJECT TO ELECTROSTATIC DAMAGE

OR DECREASE IN RELIABILITY.

HANDLING PRECAUTIONS REQUIRED.

Code Input Output

IC — C TC — — PC E —

Changes or modifications not expressly approved by ADTRAN could void the user’s authority to operate this equipment.

TELECOMMUNICATIONS CODES

-48 VDC Backup Battery Pack

1175044L2

BATTERY BACKUP

TA 750

V.35

WARNING: 20 Hz FUSE

MUST BE REMOVED

BEFORE REMOVING COVER.

MANAGEMENT

CAUTION

During TA 750 wall

installation, position

the chassis so front

panels face up.

FT1

Terminal

LX IN

access

LY IN

R1-I

cover

EU2

T1-I

LX OUT

R-O

LY OUT

T-O

EU1 MLT-A MLT-B

-48ALM MJ MJR

-48 R

MJV

MJVR

-48 V

POWER

-54 VDC Output to TA 750

AC/DC Power Supply Battery Charging Unit

P/N: 1175043LX

AC Power Input

120VAC/

2A 60HZ INPUT

-54VDC OUTPUT

AC ALARM

BATTERY

OUTPUT

INPUT

GROUND

Charging/Discharging Line

To Alarms

-54 VDC Battery