AdvanceCAM
IntraOral Camera
Operation And
Installation Manual
Advance Video Remote Control:
Full / Quad Button: Choose to capture image in full screen or
capture 4 images (quad).
F/M: Press button to capture image on monitor
Delete Button: Press shaded quad (1,2,3 or 4) to “delete”
image from that specific quad. Press “Freeze Button” to recapture image for specific quad.
Zoom Button: Press shaded quad (1,2,3 or 4) to “zoom”
image from that specific quad. Press again to return to normal
size.
Delete Single Image: This function will delete the single
image that is displayed on the screen.
Delete All Memory: This will delete all images stored in
memory. When pressed you will be asked “ARE YOU
SURE?” To proceed, press the “delete all memory” button
again and this will delete all images stored in memory.
Previous Image and Next Image: Allows you to scroll
through the images stored in the camera memory.
Clear: When looking at an image in memory press the clear button to delete it out of the memory bank.
Docking Station AIC815
Full / Quad Button: Push button to capture image(s) in full
screen or 4 images (quad).
Choice Button: Press the choice button to highlight image 1 2
3 or 4 when in quad mode. The number will turn green. This
function only works in quad mode.
Zoom Button: Use choice to select then press zoom while the
number is highlighted green, this will zoom in on selected
image. Press again to return to normal size.
Freeze Button: Press to capture image. Press to return to live
image.
Advance Cam
Press “Freeze button” to freeze image. Press “Freeze
button” again to copy image into memory. There is also an
additional button on the wand that will allow you to change
from “full” to “quad”. Press this button once and it will put
you in “quad” mode. Press a second time and the camera
will go back to a “full” screen mode. While in “quad” mode
you must depress the capture button only four times to freeze
all images if you press the button a fifth time the image will
be copied into memory.
Freeze Button: Press
button to freeze image on
monitor.
Transmitter:AIC900
Full / Quad Button: Choose
to capture image in full
screen or
capture 4 images
(quad).
The transmitter has a power indicator that will
show low medium and high power. The
transmitter also has a channel selector that will
select from channels 1 to 4. The power switch is
located on the right side of the unit if looking from
the front as shown
Power Indicator
Shows green for
high power and red
for low power.
DC Power input
used to charge the
battery
Channel Selector
Wireless Channel
display
Plug this end into
the camera.
Power Switch On
and Off.
p
p
I
ntraoral Camera
Installation Instructions
AdvanceCAM
Turn power to
transmitter on and off.
Light will emit from
end of camera when
ower is on.
Turn power to
transmitter on and off.
Light will emit from
end of camera when
ower is on.
AIC 850
AIC 900
AIC810
AIC815
Connect Camera wand
cable to wireless
transmitter if you
desire wireless
operation.
Connect camera
transmitter to the
back of the
camera.
Connect camera
wand cable to
docking station if
you desire corded
use.
1. Prior to using the TPC-WIC 850, AIC900 charge the
Wireless Video Module TX until the power supplies LED
turns back to green. It will be red while the unit is charging.
After the charging period is over, it is recommended that the
power charger be removed from the transmit ter.
2. Disconnect power supply from Wireless Video Module
TX “DC In” port.
3. Connect EZ Cam cord to Wireless Video Module TX
“Cam” port.
AIC850
AIC888
AIC810
4. Plug adv20 “switching power adapter” into Docking
Station ADV-20 /AIC815 “DC 5VIN” port. Plug power
supply into wall outlet.
AIC810
5. Plug RCA jack or S-Video into Docking Station ADV20 “AV Out” or “YC Out” port. Connect other end of video
cable into Video Input port on monitoring device (pc or TV).
Note you only need to use one video output S-video Or RCA.
AIC815
6. Plug RCA jack or S-Video into Docking Station AIC 815
“AV Out” or “S0video out” port. Connect other end of video
cable into Video Input port on monitoring device. If you wish
to use a USB 2.0 Connection to a computer use the supplied
cable. Make sure you have the driver disc. Refer to the manual
on the driver disc for help installing the drivers and software
onto a PC .
Notes: Cameras that start with PA or NT, you will need to
press the freeze button to activate the camera’s LED’s.
This will turn the camera on. Then you will be able to see
an image from the camera.
Docking Station Settings:
AIC800,805,810,815
• Switches 1-4 are to select the docking station’s
channels. Only one can be set to the on position.
They must correspond to the transmitter’s setting.
• The P and N are to select which system is being
used. P is for PAL and N is for NTSC. This must
match the camera SN. Look on the back of the
camera to see if you SN# starts with a P or an N.
Then determine which setting will work for your
configuration.
• The W-L and W are to set the docking station to
wireless or corded mode. W-L is for wireless and
W is for corded.
Troubleshooting Guide
The remote to my camera does not work.
1. Point the remote towards the lens of the camera,
press any button and hold on the remote. You should
see light flickering on the monitor. You must use the
camera to see this because the human eye cannot
detect this light.
2.
If there is no light try changing the battery in the
remote.
3.
If problem persists call your local dealer.
There is no light coming from the end of my camera.
1. Check to see if the transmitter is fully charged.
2.
Check the connection in the end of the camera
wand cord.
3.
Hook the camera up directly to the receiver.
4.
If none of the three steps work, the camera may
have internal damage. Contact your local dealer.
Loading...