ADLINK NuPRO-E340 User Manual

NuPRO-E340

Full-Size PICMG 1.3 Intel® Core™ i7/i5/i3

LGA1155 SHB

User’s Manual

Manual Rev.: 2.03
Revision Date: June 29, 2012
Part No: 50-13069-1020

Advance Technologies; Automate the World.

Revision History

Revision Release Date Description of Change(s)

2.00 2011/09/01 Initial release

2.01 2011/10/21

2.02 2012/04/23

2.03 2012/06/29 Add fix for COM5/6 IRQ reversed - Windows XP

Correct ATX 12V Power Connector label; add
PS/2 KB/MS pin header definition

Correct COM3, COM6 connector locations; add
PCIe Ports 0-3 Configuration to BIOS (version
A1.6 and higher); add DVI-D pin header and
optional Bracket Connector pin definitions

ii Revision History

NuPRO-E340

Preface

Copyright 2011-2012 ADLINK Technology, Inc.

This document contains proprietary infor mation protected by copy­right. All rights are reserved. No part of this manual may be repro­duced by any mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.

Disclaimer

The information in this document is subject to change without prior
notice in order to improve reliability, design, and function and does
not represent a commitment on the part of the manufa cturer.

In no event will the manufacturer be liable for direct, indirect, spe­cial, incidental, or consequential damages arising out of the use or
inability to use the product or documentation, even if advised of
the possibility of such damages.

Environmental Responsibility

ADLINK is committed to fulfill its social responsibility to global
environmental preservation through compliance with the Euro­pean Union's Restriction of Hazardous Substances (RoHS) direc­tive and Waste Electrical and Electronic Equipment (WEEE)
directive. Environmental protection is a top priority for ADLINK.
We have enforced measures to ensure that our products, manu­facturing processes, components, and raw materials have as little
impact on the environment as possible. When products are at their
end of life, our customers are encouraged to dispose of them in
accordance with the product disposal and/or recovery programs
prescribed by their nation or company.

Trademarks

Product names mentioned herein are used for identification pur­poses only and may be trademarks and/or registered trademarks
of their respective companies.

Preface iii

Using this Manual

Audience and Scope

The NuPRO-E340 User’s Manual is intended for hardware

technicians and systems operators with knowledge of installing,
configuring and operating industrial grade single boar d computers.

Manual Organization

This manual is organized as follows:
Preface: Presents important copyright notifications, disclaimers,

trademarks, and associated information on the proper under st and­ing and usage of this document and its associated product(s).

Chapter 1, Introduction: Introduces the NuPRO-E340, its fea­tures, applications, and specifications, including functional
descriptions and board layout.

Chapter 2, Hardware Information: Provides technical informa­tion on connectors and jumpers for configuring the NuPRO-E340.

Chapter 3, Getting Started: Illustrates how to install components
on the NuPRO-E340 such as CPU, heatsink, and memory mod­ules.

Chapter 4, Driver Installation: Provides information on how to
install the NuPRO-E340 device drivers.

Chapter 5, BIOS Setup: Describes basic navigation for the
AMIBIOS®8 BIOS setup utility.

Appendix A, Watchdog Timer: Presents information on imple­menting the watchdog timer.

Appendix B, System Resources: Presents information on I/O
mapping, IRQ routing, and resource allocation.

Important Safety Instructions: Presents safety instructions all
users must follow for the proper setup, installation and usage of
equipment and/or software.

Getting Service: Contact information for ADLINK’s worldwide
offices.

iv Preface

NuPRO-E340

Conventions

Take note of the following conventions used throughout this
manual to make sure that users perform certain tasks and
instructions properly.

Additional information, aids, and tips that help users perform
tasks.

NOTE:

NOTE:

Information to prevent minor physical injury, component dam­age, data loss, and/or program corruption when trying to com-

CAUTION:

WARNING:

plete a task.

Information to prevent serious physical injury, component
damage, data loss, and/or program corruption when trying to
complete a specific task.

Preface v

This page intentionally left blank.

vi Preface

NuPRO-E340

Table of Contents

Revision History...................................................................... ii

Preface.................................................................................... iii

List of Figures........................................................................ xi

List of Tables........................................................................ xiii

1 Introduction ........................................................................ 1

1.1 Overview.............................................................................. 1

1.2 Features............................................................................... 2

1.3 Specifications....................................................................... 3

1.4 Block Diagram ..................................................................... 5

1.5 Functional Description ......................................................... 6

1.6 Mechanical Drawing ............................................................ 9

1.7 I/O Connectivity ................................................................. 10

1.8 Power Consumption ............................... ... ... ..................... 11

1.9 Package Contents ............................................................. 12

2 Hardware Information...................................................... 13

2.1 Rear Panel I/O Ports.......................................................... 13

2.2 Board Layout ..................................................................... 15

2.3 Onboard Connectors ......................................................... 16

2.4 Jumpers............................................................................. 21

3 Getting Started ................................................................. 23

3.1 Installing the CPU.............................................................. 23

3.2 Installing the CPU Fan and Heatsink................................. 27

3.3 Installing Memory Modules................................................ 28

4 Driver Installation............................................................. 31

4.1 Intel® Rapid Storage Technology Driver ........................... 31

vii

4.2 Intel® Q67 Express Chipset Driver.................................... 32

4.3 Display Driver..................................................................... 32

4.4 Ethernet Driver................................................................... 33

4.5 Intel® Rapid Storage Technology Utility............................ 33

4.6 Intel® Active Management Technology............................. 33

4.7 TPM Driver......................................................................... 33

4.8 USB 3.0 Driver................................................................... 34

4.9 Audio Driver....................................................................... 34

4.10 Fix for COM5/6 IRQ Reversed - Windows XP ................... 35

5 BIOS Setup........................................................................ 37

5.1 Starting the BIOS............................................................... 37

5.2 Main Setup......................................................................... 41

5.3 Advanced BIOS Setup....................................................... 43

5.3.1 ACPI Settings ................................................................44

5.3.2 Trusted Computing ........................................................45

5.3.3 CPU Configuration.........................................................46

5.3.4 SATA Configuration................................................ ... ... .48

5.3.5 Intel TXT Configuration........................... ... ... ... .... ... ... ... .49

5.3.6 Intel IGD SWSCI OpRegion...........................................50

5.3.7 USB Configuration.........................................................51

5.3.8 Super IO Configuration..................................................53

5.3.9 Hardware Monitor............... .... ... ... ... ..............................54

5.3.10AMT Configuration.........................................................56

5.3.11Serial Port Console Redirection.....................................57

5.4 Chipset Setup .................................................................... 61

5.4.1 Graphics and Memory Bridge Configuration..................62

5.4.2 PCH Bridge Configuration .............................................63

5.4.3 Management Engine Subsystem...................................65

5.5 Boot Configuration............................................................. 67

5.6 Security Setup.................................................................... 69

5.7 Exit Menu........................................................................... 71

viii

NuPRO-E340

A Appendix: Watchdog Timer..............................................73

A.1 Sample Code..................................................................... 73

B Appendix: System Resources..........................................77

B.1 System Memory Map......................................................... 77

B.2 Direct Memory Access Channels....................................... 77

B.3 IO Map................................ .... ... ... ... .... ... ... ... ... .... .............. 78

B.4 Interrupt Request (IRQ) Lines............................................ 79

Important Safety Instructions.............................................. 85

Getting Service...................................................................... 87

ix

This page intentionally left blank.

x

NuPRO-E340

List of Figures

Figure 1-1: NuPRO-E340 Block Diagram .......................................... 5

Figure 1-2: NuPRO-E340 Board Dimensions ....................................9

Figure 2-1: Rear Panel I/O Ports...................................................... 13

Figure 2-2: Connectors and Jumpers................... ... ... ... .... ... ... ... .... .. 15

List of Figures xi

This page intentionally left blank.

xii List of Figures

NuPRO-E340

List of Tables

Table 1-1: NuPRO-E340 General Specifications.............................. 3

Table 1-2: NuPRO-E340 I/O Connectivity ......................................10

Table 1-3: Core™ i7-2600 Processor Power Consumption............11

Table B-1: System Memory Map..................................................... 77

Table B-2: Direct Memory Access Channels................................... 77

Table B-3: IO Map...........................................................................78

Table B-4: IRQ Lines PIC Mode....................... ... ... ... ... .... ... ... ... .... .. 79

Table B-5: IRQ Lines APIC Mode....................... ... ... ... .... ... ...... .... .. 81

Table B-6: PCI Configuration Space Map.... .... ... ... ... ... .... ... ... ... .... .. 83

Table B-7: PCI Interrupt Routing Map.............................. ... ... ... .... .. 84

List of Tables xiii

This page intentionally left blank.

xiv List of Tables

NuPRO-E340

1 Introduction

1.1 Overview

The ADLINK NuPRO-E340 is a PICMG 1.3 System Host Board
(SHB) supporting the next-generation Intel® Core™ i7/i5/i3 and
Pentium® processors in LGA1155 package to deliver a scalable
high performance platform for a wide array of industrial
applications. The NuPRO-E340 supports 32nm process CPUs at
up to 3.4 GHz with integrated graphics and memory controllers,
Direct Media Interface (DMI) and Flexible Display Interface (FDI)
connectivity to the Intel® Q67 Express Chipset. Dual-channel
DDR3 1066/1333 MHz memory is supported up to a maximum of
8 GB in two DIMM slots.

These advanced features, coupled with PCI Express® x16 expan­sion capability, dual PCI Express®-based Gigabit Ethernet, SATA
6 Gb/s and USB 3.0 support make the NuPRO-E340 ideal for
vision and automation control applications.

Introduction 1

1.2 Features

X Supports Intel® Core™ i7/i5/i3 and Pentium® processors in

LGA1155 package

X Integrated Intel® HD Graphics
X PCI Express® x16 expansion capability via backplane
X Dual Gigabit Ethernet
X 2x USB 3.0 ports onboard
X 12x USB 2.0 ports (8x onboard, 4x on backplane)
X 2x SATA 6 Gb/s ports onboard
X 4x SATA 3 Gb/s ports (2x onboard, 2x on backplane)
X 6x COM ports (including 1x RS-232/422/485/485+)
X Watchdog Timer, Hardware Moni tor
X Optional HD audio kit (DB-Audio2 daughter board)
X TPM hardware security chip
X RoHS compliant

To purchase the optional DB-Audio2 daughter board, please
contact your ADLINK sales representative.

NOTE:

NOTE:

2Introduction

1.3 Specifications

System

• Intel® Core™ i7-2600, 3.4 GHz, 8M Cache, 95W TDP

CPU

Chipset • Intel® Q67 Platform Controller Hub
Memory
BIOS • AMIBIOS in 64-Mbit SPI Flash
Audio
Watch Dog

Timer
Hardware

Monitor
TPM • Infineon SLB 9635 TT 1.2

Operating
Systems

I/O Ports

PCIe/PCI

Integrated • Integra te d Intel® HD Graphics
External • PCI Express x16

• Intel® Core™ i5-2400, 3.1 GHz, 6M Cache, 95W TDP

• Intel® Core™ i3-2120, 3.3 GHz, 3M Cache, 65W TDP

• Intel® Pentium® G850, 2.9GHz, 3M Cache, 65W TDP

• Two 240-pin DIMM sockets support dual-channel
1066/1333 MHz DDR3 (up to 8 GB)

• Intel® High Definition Audio support via DB-Audio2
daughter board

• 1-255 second or 1-255 minute programmable and can
generate system reset.

• CPU/System temperature, fan speed and onboard DC
voltage

• Windows® XP, 7 32/64-bit,

• Fedora™ 14

• Red Hat® Enterprise Linux® 5

I/O Interfaces

• 2x USB 3.0 port on re ar panel

• 8x USB 2.0 via onboard header, 4x via backplane

• 2x SATA 6 Gb/s ports onboard

• 4x SATA 3 Gb/s ports (2x onboard, 2x on backplane)

• 6x serial ports via onboard pin-header
(5x RS-232, 1x RS-232/422/485/485+)

• 2x Gigabit Ethernet RJ45 ports

• 1x VGA port (Dsub-15)

• 1x DVI-D via onboard pin-header (opt. cable bracket

• 1 x parallel port

• PCIe-x16, PCIe-x4 and PCI 32bit/33MHz via golden
fingers

Graphics

Table 1-1: NuPRO-E340 General Specifications

NuPRO-E340

)

Introduction 3

Ethernet

• Dual Gigabit Ethernet (Intel® 82579LM Gigabit
Ethernet PHY, Intel® 82574L Gigabit Ethernet

Controller

Ports • Two RJ-45 Ethernet ports

Form Factor • Standard full-size PICMG 1.3 SHB
Dimensions • 338 x 12 6 mm (L x W)
Operating Temp. • 0ºC to 60ºC
Storage Temp. • -20ºC to 80ºC
Relative

Humidity
Safety • CE, FCC Class A

Table 1-1: NuPRO-E340 General Specifications

Controller)

• Supports Preboot Execution Environment (PXE),
Wake-On-LAN, and Intel® AMT 7.0 on LAN1
(82579LM)

Mechanical and Environment

• 10% to 90% non-condensing

4Introduction

1.4 Block Diagram

NuPRO-E340

Discrete Graphics

on backplane

DVI-D

onboard header

CRT

DB15

SATA ports

(2x 6 Gb/s, 4x 3 Gb/s)

USB 3.0

(2x rear panel)

USB 2.0

(8x onboard, 4x internal)

KB/Mouse

LPT

RS-232

(COM2-6)

RS-232/422/

485/485+

(COM1)

PCIe x16 Gen2.0

ASM 1442

Level Shift IC

ASM1042

TPM

Integrated

HD Graphics

FDI

SATA

USB 2.0

LPC

ITE8783

LPC Super I/O

CPU

Core™ i7/i5/i3

quad/dual cores

32nm process

LGA1155 package

Intel Q67 PCH

HD

Codec

SPI

PCIe

Controller

PCI

Controller

Hardware

DDR Channel A

DDR3 1066/1333 MHz

DDR Channel B

DMI x4

PCIe x1 or x4

PCIe x1

C

P

PCI Bus

Header for
DB-Audio2

Monitor

x

1

e

I

SPI BIOS

DIMM x2

backplane

Intel 82579

RJ-45(LAN1)

Intel 82574L

RJ-45 (LAN2)

PCI 32-bit/33MHz

on backplane

Figure 1-1: NuPRO-E340 Block Diagram

Introduction 5

1.5 Functional Description

Processor Support

The NuPRO-E340 is PICMG 1.3 System Host Board supporting
the 2nd generation Intel® Core™ processor family (Intel® Core™
i7/i5/i3) in LGA1155 socket. An integrated memory controller sup­ports dual channel 1066/1333 MHz DDR3 and Intel® HD Graphics
is integrated onboard the CPU. The CPU provides a PCI Express
x16 for external graphics or expansion. Direct Media Interface
(DMI) and Flexible Display Interface (FDI) provide connectivity to
the Intel® Q67 Express Chipset.

Intel® Q67 Express Chipset

The Intel® BD82Q67 Platform Controller Hub (PCH) combines
with the processor to provide a compact yet powerful 2-chip solu­tion. Direct Media Interface (DMI) is the chip-to-chip connection
between the processor and PCH. Intel® Flexible Display Interface
carries display traffic from the integrated graphics in the processor
to the legacy display connectors in the PCH. The PCH supports all
other required interfaces including PCI Express, SATA 6 Gb/s,
USB 2.0, PCI, LPC, and SPI.

Dual-Channel DDR3 Memory

To meet the requirements of memory-intensive applications, the
NuPRO-E340 has a dual-channel memory architecture supporting
DDR3 1066/1333 MHz DIMMs. The key advantages of DDR3 are
the higher bandwidth and the increase in performance at lower
power than DDR2. DDR3 memory technology meets the require­ments of the latest 3D graphics, multimedia, and network applica­tion, and boosts system performance by eliminating bottlenecks.

Gigabit Ethernet

The NuPRO-E340 utilizes an Intel® 82579LM Gigabit Ethernet
PHY and Intel® 82574L Gigabit Ethernet Controller connected to
the PCI-E bus of the Q67 PCH. Intel® AMT 7.0 (82579LM on
LAN1), Wake-on-LAN and PXE are supported.

6Introduction

NuPRO-E340

Serial ATA

The NuPRO-E340 provides six Serial ATA ports with data transfer
rates of up to 6.0 GB/s on 2 ports and up to 3.0 GB/s on 4 ports.
Intel® Rapid Storage Technology supports AHCI and RAID
0/1/5/10 functionality.

Universal Serial Bus (USB 2.0/3.0)

The NuPRO-E340 provides 12 USB 2.0 ports supporting transfer
rates up to 480 Mb/s and two USB 3.0 ports on the rear panel I/O
supporting transfer rates up to 5 Gb/s (ASM1042 controller via
PCIe). All ports are USB 2.0/1.1 compatible.

The USB 3.0 ports cannot be used to install Windows as the
necessary drivers are currently not included with the OS. Linux

NOTE:

NOTE:

kernels 2.6.31 and higher can be installed using th e USB 3.0
ports.

Hardware monitoring

A built-in, proactive hardware monitoring system in the Super I/O
monitors the CPU temperature, system fan speed, and voltage
levels to prevent overheating and/or component damage, effect
timely failure detection, and ensure stable supply of current for
critical components.

Watchdog Timer

The watchdog timer (WDT) monitors system operations based on
user-defined configurations. The WDT can be programmed for dif­ferent time-out periods, such as from 1 to 255 seconds or from 1 to
255 minutes. The WDT generates a reset signal, then a reset
request, after failure to strobe it within the programmed time
period. A register bit may be enabled to indicate if the watchdog
timer caused the reset event. The WDT register is cleared during
the power-on sequence to enable the operating system to take
appropriate action when the watchdog generates a reboot.

Trusted Platform Module

The NuPRO-E340 optionally supports TPM ver. 1.2 (Trusted Plat­form Module) for secure storage of keys, passwords and digital

Introduction 7

certificates. Systems supporting TPM offer improved hard­ware-based security in numerous applications, such as file and
folder encryption, local password management, S-MIME e-mail,
VPN and PKI authentication and wireless authentication for

802.1x and LEAP.

Intel® Active Management Technology

Intel® Active Management Technology (Intel® AMT) is hard­ware-based technology for remot ely managing and securing PCs
out-of-band. Intel® AMT includes hardware-based remote man­agement, security, power-management, and remote-configuration
features. Intel® AMT allows remote access to a system when tra­ditional techniques and methods are not availa b l e.

8Introduction

1.6 Mechanical Drawing

NuPRO-E340

Dimensions

in mm

Figure 1-2: NuPRO-E340 Board Dimensions

Introduction 9

1.7 I/O Connectivity

I/O Bracket Onboard

VGA Y — — DB-15

DVI-D — Y —

LAN1/2 (RJ-45)

PS/2 KB/MS — Y — —

USB Rear Panel 2 — — USB 3.0

USB headers — 8 — 2.54” pitch

USB backplane — — 4 —

COM1-2 — Y —
COM3-6 — Y —

Parallel port — Y — —

SATA — 4 2 —

PCIe x4 — — Y —

PCIe x16 — — Y —

PCI 32bit/33MHz — — Y —

Table 1-2: NuPRO-E340 I/O Connectivity

Y——

Golden

Finger

Remarks

cable w/ bracket

optional

Act/Link/

Speed LEDs

2.54” pitch

2.00" pitch

10 Introduction

NuPRO-E340

1.8 Power Consumption

Intel® Core™ i7-2600 Processor (8M Cache, 3.40 GHz)

T est Configuration

CPU Intel® Core™ i7-2600 Processor 3.40 GHz (4 cores)
Memory
Graphics Integrated Intel® HD Graphics

SATA Channel 1 Seagate ST9160412 AS Barracuda 7200.4 160GB
Power Supply FSP FSP350-60PFG
Backplane ADLINK EBP-13E2

Power Req. +12V +5V +3.3V Total

Current (A) 1.90 1.93 0.86 —

Power (W) 22.8 9.65 2.84 35.3

Power Req. +12V +5V +3.3V Total

Current (A) 1.34 1.58 0.86 —

Power (W) 16.1

Power Req. +12V +5V +3.3V Total

Current (A) 6.14 1.99 0.89 —

Power (W) 73.7 9.95 2.94 86.6

Windows XP, Total System Stress (BurnIn Test)

Power Req. +12V +5V +3.3V Total

Current (A) 6.80 3.55 1.31 —

Power (W) 81.6 17.8 4.32 103.7

Unigen 2GB DDR3 1333 UDIMM 240-pin
2x 2GB in 2 DIMM slots

DOS (idle)

Windows XP, logon screen (idle)

7.90 2.84

Windows XP, CPU Stress (BurnIn Test)

26.8

Table 1-3: Core™ i7-2600 Processor Power Co nsumption

Introduction 11

1.9 Package Contents

Before unpacking, check the shipping carton for any damage. If
the shipping carton and/or contents are damaged, inform your
dealer immediately. Retain the shipping carton and packing
materials for inspection. Obtain authorization from the dealer
before returning any product to ADLINK.

X NuPRO-E340
X SATA data cable with latch x2
X 2-port USB cable with bracket
X 2-port COM cable with bracket for COM1/COM2

(2.54 mm pitch)

X 2-port COM cable with bracket x2 for COM3-6

(2.0 mm pitch)

X Driver DVD
X User’s manual

The NuPRO-E340 must be protected from static discharge and
physical shock. Never remove any of the socketed parts except

WARNING:

at a static-free workstation. Use the anti-static bag shipped with
the product to handle the board. Wear a grounded wrist strap
when installing and/or servicing.

12 Introduction

NuPRO-E340

2 Hardware Information

This chapter provides information on the NuPRO-E340 board lay­out, connector pin assignments, and jumper settings.

2.1 Rear Panel I/O Ports

1 2 3

Figure 2-1: Rear Panel I/O Ports

Connector Description

1 LAN1 port (RJ-45) Gigabit Ethernet (supports Intel® AMT)
2 LAN2 port (RJ-45) Gigabit Ethernet
3 VGA port DB-15 connector for CRT or LCD monitor
4 USB 3.0 ports SuperSpeed USB 3.0 ports

4

USB 3.0 Connectors

Pin # Signal Name

1 USB3.0_P5VA
2 USB2_CMAN
3 USB2_CMAP
4GND
5 USB3A_CMRXN
6 USB3A_CMRXP
7GND
8USB3A_CMTXN
9 USB3A_CMTXP

The USB 3.0 ports do not function during system boot or under
DOS and are only available after the driver is loaded by the OS.

NOTE:

NOTE:

Hardware Information 13

For USB support during BIOS setup and system install, connect a
USB cable with bracket to one of the onboard USB pin headers.

LAN (RJ-45) Ports

10BASE-T/

100BASE-TX

1000BASE-T

LED1

LED2

18

Pin #

1 TX+ BI_DA+
2 TX- BI_DA­3 RX+ BI_DB+
4 -- BI_DC+
5 -- BI_DC­6 RX- BI_DB­7 -- BI_DD+
8 -- BI_DD-

Refer to the table below for the LAN port LED definitions.

LED1 LED2

Status Description Status Description

Off No Link Off 10 Mb connection
On Linked Green 100 Mb connection

Blinking Data Activity Amber 1 Gb connection

VGA Port

Pin # Signal Pin # Signal

1Red9+5 V
2 Green 10 Ground
3Blue11NC
4 NC 12 DDC DAT
5 Ground 13 HSYNC
6 Ground 14 VSYNC
7 Ground 15 DDC CLK
8 Ground

14 Hardware Information

2.2 Board Layout

NuPRO-E340

3

42

1

5
6

15

16

20

Figure 2-2: Connectors and Jumpers

Connector Description

1 CN24 ATX 12V Power connector
2 DIMM1/2 DDR3 DIMM slots
3 CN23 System Panel pin header
4 FAN2 System fan connector
5 CN2/4 SATA 6 Gb/s connectors (blue)
6 CN5/7 SATA 3 Gb/s connectors (black)
7 CN15 Parallel Port connector
8 CN12 COM3 connector
9 CN14 COM5 connector

10 CN13 COM4 connector

11 CN16 COM6 connector
12 CN17 DVI-D pin header
13 CN11 COM2 connector
14 JP1-4 COM1 mode jumpers
15 CN3/6/8/X1 USB 2.0 pin headers
16 CN9 HD Audio Daughter Board pin header
17 CN10 COM1 connector (RS-232/422/485/485+)
18 CN27

PS/2 Keyboard/Mouse pin header
19 JBAT1 Clear CMOS
20 FAN1 CPU fan connector

8 9 10 11 12 13

7

17

19

14

18

Hardware Information 15

2.3 Onboard Connectors

Serial ATA Connectors (CN2/4/5/7)

Pin # Signal

1

7

USB 2.0 Connectors (CN3/6/8/X1)

1GND
2TXP
3TXN
4GND
5RXN
6RXP
7GND

Pin # Signal Pin # Signal

1 +5V 2 +5V
3 USB0- 4 USB1­5 USB0+ 6 USB1+
7 GND 8 GND
9Key 10NC

PS/2 Keyboard/Mouse Pin Header (CN27)

1

Pin # Signal Pin # Signal

2

1 KBDATA 2 KBCLK
3 MSDATA 4 MSCLK
5 KM_VCC 6 GND

ATX 12V Power Connector (CN24)

Pin # Signal

2
4

16 Hardware Information

1
3

1GND
2GND
3 +12V DC
4

+12V DC

NuPRO-E340

HD Audio Daughter Board Connector (CN9)

This connector is designed for use with the ADLINK DB-Audio2
daughter board.

Pin # Signal Function

1 GND Ground
2 AUD_BCLK Audio Clock
3 GND Ground

12

910

4 ICH_AUD_SDIN1 Audio Data Input
5 P5V + 5V
6 ICH_AUD_SDOUT Audio Data Output
7 P5V_ A UD + 5V
8 P3V3_DVDD 3.3V
9 AUD_SYNC Audio Synchronous

10 AUD_RST J Audio Reset

COM1~6 Connector (RS-232) (CN10/11/12/13/14/16)

Pin # RS-232 Signal

1 DCD
2DSR
3RXD

12

4RTS
5TXD

910

6CTS
7DTR
8RI
9GND

10 NC

COM1 COM2 COM3 COM4 COM5 COM6

Connector CN10 CN11 CN12 CN13 CN14 CN16

Pitch 2.54 mm 2.54 mm 2.00 mm 2.00 mm 2.00 mm 2.00 mm

Hardware Information 17

COM1 Connector (RS-422/485/485+) (CN10)

Pin # RS-422/485+ RS-485

1TXD- Data­2NC NC
3 TXD+ Data+

12

910

4NC NC
5RXD+ NC
6NC NC
7RXD- NC
8NC NC
9GND GND

10 NC NC

Note: See “COM1 Mode Jumper Settings (JP1-4)” on page 21.

Parallel Port Connector (CN15)

Pin # Signal Pin # Signal

1 Line Printer Strobe 2 Auto-Feed
3 Parallel Data 0 4 Error

12

5 Parallel Data 1 6 Initialize
7 Parallel Data 2 8 Select

9 Parallel Data 3 10 Ground
11 Parallel Data 4 12 Ground
13 Parallel Data 5 14 Ground
15 Parallel Data 6 16 Ground
17 Parallel Data 7 18 Ground
19 Acknowledge 20 Ground
21 Busy 22 Ground
23 Paper Empty 24 Ground
25 Select 26 NC

18 Hardware Information

System Panel Connector (CN23)

Connects to chassis-mounted buttons, speakers, and LEDs.

Pin # Signal Function Pin Group

1 WDSPK Speaker signal

1

10 20

2NC
3NC
4+5V Power
5NC
6 GND Ground

11

7 KEYLOCK Keyboard lock
8 PLED Power LED signal
9NC

10 +5V Power LED pull-up

11 GND Ground
12 RESETBT RESET signal
13 NC
14 GND Ground
15 POWERBT Power-on signal
16 NC
17 NC
18 HDDLED Hard Disk LED signal
19 +3.3V Hard Disk LED pull-up
20 NC

Chassis Speaker

Power LED

Reset Button

Power Button

NuPRO-E340

Key Lock

HDD LED

Fan Connectors (FAN1/2)

Pin # Signal

1GND

14

Hardware Information 19

2 Fan power (+12V)
3 Fan Tachometer

Fan Speed Control

4

DVI-D Onboard Connector(CN17)

Pin # Signal Pin # Signal

1 GND 2 GND

1

2

3 DVI-Clock+ 4 DVI-Data0­5 DVI-Clock- 6 DVI-Data0+
7 GND 8 GND
9 DVI-I2C-Clock 10 DVI-Data1-

11 DVI-I2C-Data 12 DVI-Data1+
13 GND 14 GND
15 DVI-HPD 16 DVI-Data2­17 +5V 18 DVI-Data2+
19 GND 20 GND

DVI-D Bracket Connector

(optional cable w/ bracket, P/N 30-01052-2000)

Pin # Signal Pin # Signal

1 TMDS Data2- 13 TMDS Data3+
2 TMDS Data2+ 14 +5 V Power
3 TMDS Data2/4 Shield 15 GND
4 TMDS Data4- 16 Hot Plug Detect
5 TMDS Data4+ 17 TMDS Data0­6 DDC Clock [SCL] 18 TMDSData0+
7 DDC Data [SDA] 19 TMDS Data0/5 Shield
8 Analog vertical sync 20 TMDS Data5-

9 TMDS Data1- 21 TMDS Data5+
10 TMDS Data1+ 22 TMDS Clock Shield
11 TMDS Data1/3 Shield 23 TMDS Clock +
12 TMDS Data3- 24 TMDS Clock -

20 Hardware Information

NuPRO-E340

2.4 Jumpers

Clear CMOS (JBAT1)

The CMOS RAM data contains the date / time and BIOS setting
information. CMOS is powered by the onboard button cell battery.
To erase the CMOS RAM data:

1. Power down and disconnect power from the system.

2. Short pins 2-3 on JP1.

3. Reconnect power and power up the system.

4. After power up, remove the jumper cap from pins 2-3
and reinstall it to pins 1-2.

RTC status Connection JBAT1

Normal 1 – 2

Clear CMOS 2 – 3

COM1 Mode Jumper Settings (JP1-4)

Short the jumper pins according to the following settings to set
COM1 to RS-232/422/485/485+ mode:

RS-232 RS-422 RS-485 RS-485+

JP1 1-2 3-4 5-6 5-6
JP2 1-3, 2-4 3-5, 4-6 3-5, 4-6 3-5, 4-6
JP3 1-3, 2-4 3-5, 4-6 3-5, 4-6 3-5, 4-6
JP4 – 1-3, 2-4 1-3, 2-4 3-5, 4-6

Hardware Information 21

This page intentionally left blank.

22 Hardware Information

NuPRO-E340

3 Getting Started

This chapter provides information on how to in stall components on
the NuPRO-E340 SHB.

3.1 Installing the CPU

The NuPRO-E 340 supports an Intel® Core™ i7/i5/ i3 or Pentiu m®
processor in an LGA1155 socket.

Disconnect all power to the board before
installing a CPU to prevent damaging the

WARNING:

To install the CPU:

1. Press down on the locking arm (A), then push it away from

board and CPU.
Do not touch socket contacts. Damaging the

contacts voids the product warranty. Follow
the installation instructions carefully to avoid
damaging the board components.

the socket to disengage it from the retention tab (B).

A

B

Getting Started 23

2. Raise the locking arm to unlock the load plate.

3. Lift the load plate to uncover the socket.

4. Remove the plastic protective cover from the socket.
Note the locations of the alignment keys (A) and Pin 1
indicator (B).

B

A

Do NOT touch socket contacts.

WARNING:

24 Getting Started

5. Hold the CPU using thumb and forefinger as shown.

Position the CPU over the socket, matching the notches
on the sides of the CPU with the alignment keys on the
socket (A). The golden triangle on the CPU must be
positioned at the corner of the socket with the Pin 1 indi­cator as shown (B).

AB

The CPU fits into the socket in only one orientation. DO NOT
force it into the socket to avoid causing damage.

WARNING:

NuPRO-E340

6. Carefully place the CPU into the socket vertically. The

socket has cutouts for your fingers to fit into.

Cutouts

Getting Started 25

7. Gently lower the load plate. Make sure the front edge of the
plate is under the screw as indicated.

8. Lower the locking arm and fasten it to the retention tab (A).
The load plate should be locked underneath the screw as
shown (B).

B

A

26 Getting Started

NuPRO-E340

3.2 Installing the CPU Fan and Heatsink

The CPU requires a chassis with an airflow inlet and maximum
internal ambient temperature of 50° C. A especially-designed

CAUTION:

When the CPU fan installation procedures presented here are
inconsistent with the installation procedures you obtained from the
CPU fan and heatsink package, follow the latter.

To install the CPU fan:

CPU fan and heatsink must be installed before using the SHB.
Failure to install a CPU fan and heatsink may damage the sys­tem host board and/or the CPU.

1. Apply thermal grease evenly on top of the installed CPU.

2. Lower the CPU fan to the CPU, then secure it using the

provided attachments or screws.

3. Connect the CPU fan cable to the CPU fan connector on

the SHB labeled FAN1 (see “Board Layout” on page 15).

Getting Started 27

3.3 Installing Memory Modules

The NuPRO-E340 supports up to 8 GB of DDR3 1066/1333 MHz
memory modules in two DIMM sockets. A DDR3 module has a
240-pin footprint compared to the legacy 184-pin DDR DIMM.
DDR3 modules are notched to facilitate correct installation in the
DIMM sockets.

Disconnect all power to the board before installing a memory
module to prevent damaging the board and memory module .

WARNING:

Memory Configuration Options

The NuPRO-E340 supports 1GB, 2GB and 4GB unbuffered non­ECC DDR3 DIMMs in the following configurations:

X Channel A: DIMM1

Channel B: DIMM2

X For dual-channel configuration, the total size of memory

module installed per channel must be the same
(DIMM1 = DIMM2).

X It is recommended that you install DIMMs with the same

CAS latency. For maximum compatibility, install memory
modules with the same brand, model, and/or rating.

To install a memory module:

1. Locate the DIMM sockets on the motherboard.

2. Press the socket’s retaining clips outward to unlock.

28 Getting Started

NuPRO-E340

3. Align the memory module on the socket making sure

that the notch matches the break on the socket.

Notch

Break

4. Insert the module firmly into the slot until the retaining

clips snap back inwards and the module is securely
seated.

Getting Started 29

This page intentionally left blank.

30 Getting Started

NuPRO-E340

4 Driver Installation

This chapter provides information on how to install the
NuPRO-E340 device drivers under Windows XP. The device
drivers are located in the following ADLINK All-in-One DVD
directories:

Chipset \NuPRO\NuPRO-E340\Chipset\
Display \NuPRO\NuPRO-E340\VGA\
Ethernet \NuPRO\NuPRO-E340\Ethernet\
TPM \NuPRO\NuPRO-E340\TPM\
.Net Framework \NuPRO\NuPRO-E340\VGA\
Rapid Storage \NuPRO\NuPRO-E340\Others\
USB 3.0 \NuPRO\NuPRO-E340\Others\
Audio \Audio Daughter Board\DB-Audio2\

Install the Windows operating system before installing any driver.
Most standard I/O device drivers are installed during Windows
installation.

NOTE:

NOTE:

r

The USB 3.0 ports cannot be used to install Windows as the nec­essary drivers are currently not included with the OS. Linux kernels

2.6.31 and higher can be installed using the USB 3.0 ports.

In order to enable RAID or AHCI mode, you must pre-install the
Intel® Rapid Storage Technology driver during the Windows*

NOTE:

NOTE:

installation process. using the F6 installation method.
*Not required for Windows Vista and Windows 7.

4.1 Intel® Rapid Storage Technology Driver

1. Create a floppy image as described in the F6Readme.txt file

contained in X:\NuPRO\NuPRO-E340\Others\

F6_SATA_Floppy_Install_Image_WinXP32_WinVISTA32_
IRST 9.5.0.1037.zip.

2. During Windows inst allation , press F6 when you see the

message “Press F6 if you need to install a third party

SCSI or RAID driver.” Then press S to Specify Additional
Device.

Driver Installation 31

3. Insert the floppy disk and follow the remaining instruc­tions. Leave the disk in until the system has rebooted
and copied the necessary files, then remove the disk.

4.2 Intel® Q67 Express Chipset Driver

This section describes the installation of the Intel® Q67 Express
chipset driver.

1. Locate the directory X:\NuPRO\NuPRO-E340\Chipset\
on the ADLINK All-in-One DVD, and extract the file

setup.exe from the following archive: Chipset driver_
Intel_INF_Update_Utility_All_WinOS.zip.

2. Run the program setup.exe and follow the onscreen
instructions. Restart the system if prompted.

4.3 Display Driver

Integrated Intel® HD Graphics

This section describes the driver installation for the Integrated
Intel® HD Graphics.

Follow these instructions to install the display driver:

1. Locate the directory X:\NuPRO\NuPRO-E340\VGA\ on
the ADLINK All-in-One DVD, and extract the contents of
the following archive:

Microsoft_Net_Framework_v3.5_SP1.zip

2. Run the program
Microsoft_Net_Framework_v3.5_SP1.exe and follow the
onscreen instructions.Restart the system if prompted.

3. Locate the directory X:\NuPRO\NuPRO-E340\VGA\ on
the ADLINK All-in-One DVD, and extract the file
setup.exe from the following archive: VGA_winxp.zip.

4. Run the program setup.exe and follow the onscreen
instructions. Restart the system if prompted.

32 Driver Installation

4.4 Ethernet Driver

Follow these instructions to install the Ethernet driver.

1. Locate the directory

X:\NuPRO\NuPRO-E340\Ethernet\ on the ADLINK
All-in-One DVD, and extract the file Autorun.exe from the
following archive:
Network_driver_Intel_Network_Adapter_For_Win32.zip.

2. Run the program Autorun.exe and follow the onscreen

instructions. Restart the system if prompted.

4.5 Intel® Rapid Storage Technology Utility

Follow these instructions to install the Intel® Rapid Storage
Technology utility.

1. Locate the directory

X:\NuPRO\NuPRO-E340\Others\ on the ADLINK All-in-One
DVD, and extract the file setup.exe from the following archive:

Intel_Rapid_Storage_Technology_All_WinOS_v9.5.0.1037.
zip.

2. Run the program setup.exe and follow the onscreen

instructions. Restart the system if prompted.

NuPRO-E340

4.6 Intel® Active Management Technology

Follow these instructions to install the Intel® Active Management
Technology driver.

1. Locate the directory

X:\NuPRO\NuPRO-E340\Others\ on the ADLINK All-in-One
DVD, and extract the file setup.exe from the following
archive: ME_SW.zip.

2. Run the program setup.exe and follow the onscreen

instructions. Restart the system if prompted.

4.7 TPM Driver

Follow these instructions to install the TPM driver.

1. Locate the directory

X:\NuPRO\NuPRO-E340\TPM\ on the ADLINK

Driver Installation 33

All-in-One DVD, and extract the file setup.exe from the
following archive: TPM_HostSW_3.7_IFX_RTM.zip.

2. Run the program setup.exe and follow the onscreen
instructions. Restart the system if prompted.

4.8 USB 3.0 Driver

Follow these instructions to install the TPM driver.

1. Locate the directory
X:\NuPRO\NuPRO-E340\Others\ on the ADLINK
All-in-One DVD, and extract the file setup.exe from the
following archive: USB3.0.zip.

2. Run the program setup.exe and follow the onscreen
instructions. Restart the system if prompted.

4.9 Audio Driver

Follow these instructions to install the audio driver for the optional
DB-Audio2 daughter board.

Before installing the audio driver, check the BIOS settings to
make sure that audio is enabled: Chipset > PCH Configura-

NOTE:

NOTE:

tion > HDA Controller (see “PCH Bridge Configuration” on
page 63).

1. Place the ADLINK All-in-One DVD to the optical drive.

2. Locate the audio drive r from the directory
X:\Audio Daughter Board\DB-Audio2\, then dou­ble-click on the setup.exe file to start installation.

3. Follow the screen instructions to complete installation,
then restart the system if prompted.

34 Driver Installation

NuPRO-E340

4.10 Fix for COM5/6 IRQ Reversed - Windows XP

There is an issue in Windows XP that results in the IRQs of COM5
and COM6 being reversed. To fix this problem, follow these steps:

1. Install all the Windows XP drivers as described above.

2. Open the Device Manager (R-click on My Computer >

Manage > Device Manager).

3. Click the + sign next to Ports (COM & LPT) to expand

the list of devices.

4. R-click Communications Port (COM6) and select Uninstall.

5. Click OK when asked to confirm device removal.

6. R-click Communications Port (COM5) and select Uninstall.

7. Click OK when asked to confirm device removal.

Driver Installation 35

8. R-click the computer icon at the top of the device tree
and select Scan for hardware changes.

9. Windows will reinstall COM5 and COM6 with the correct
IRQs.

36 Driver Installation

NuPRO-E340

5 BIOS Setup

The following chapter describes basic navigation for the
AMIBIOS® EFI BIOS setup utility .

5.1 Starting the BIOS

To enter the setup screen, follow these steps:

1. Power on the motherboard

2. Press the < Delete > key on your keyboard when you

see the following text prompt:
< Press DEL to run Setup >

3. After you press the < Delete > key, the main BIOS setup

menu displays. You can access the other setup screens
from the main BIOS setup menu , such as Chipset and
Power menus.

Note: In most cases, the < Delete > key is used to invoke the setup

screen. There are several cases that use other keys, such as
< F1 >, < F2 >, and so on.

BIOS Setup 37

Setup Menu

The main BIOS setup menu is the first screen that you can navi­gate. Each main BIOS setup menu option is described in this
user’s guide.

The Main BIOS setup menu screen has two main frames. The left
frame displays all the options that can be configured. “Grayed”
options cannot be configured, “Blue” options can be.

The right frame displays the key legend. Above the key legend is
an area reserved for a text message. When an option is selected
in the left frame, it is highlighted in white. Often a text message will
accompany it.

Navigation

The BIOS setup/utility uses a key-based navigation system called
hot keys. Most of the BIOS setup utility hot keys can be used at
any time during the setup navigation process.

These keys include < F1 >, < F10 >, < Enter >, < ESC >, < Arrow >
keys, and so on. .

38 BIOS Setup

NuPRO-E340

Note: There is a hot key legend located in the r ight frame on most

setup screens.

The < F8 > key on your keyboard is the Fail-Safe key. It is not dis­played on the key legend by default. To set the Fail-Safe settings
of the BIOS, press the < F8 > key on your keyboard. It is located
on the upper row of a standard 101 keyboard. The Fail-Safe set­tings allow the motherboard to boot up with the least amount of
options set. This can lessen the probability of conflicting settings.

Hotkey Descriptions

F1 The < F1 > key allows you to display the General Help

screen.
Press the < F1 > key to open the General Help screen.

BIOS Setup 39

F10 Th e < F10 > key allo ws yo u to save any changes you have

made and exit Setup. Press the < F10 > key to save your
changes. The following screen will appear:

Press the < Enter > key to save the configuration and exit.
You can also use the < Arrow > key to select Cancel and
then press the < Enter > key to abort this functio n and return
to the previous screen.

ESC The < Esc > key allows you to discard any changes you have

made and exit the Setup. Press the < Esc > key to exit the
setup without saving your changes. The following screen will
appear:

Press the < Enter > key to discard changes and exit. You can
also use the < Arrow > key to select Cancel and then press
the < Enter > key to abort this function and return to the pre­vious screen.

Enter The < Enter > key allows you to display or change the setup

option listed for a particular setup item. The < Enter > key
can also allow you to display the setup sub-screens.

40 BIOS Setup

NuPRO-E340

5.2 Main Setup

When you first enter the Setup Utility , you will enter the Main setup
screen. You can always return to the Main setup screen by select­ing the Main tab. There are two Main Setup options. They are
described in this section. The Main BIOS Setup screen is shown
below.

System & Board Info

BIOS Vendor

Displays the BIOS vendor.

Core Version

Displays the BIOS core version.

Compliancy

Displays the current BIOS compliancy.

Project Version

Displays the current BIOS revision.

Build Date and Time

Displays the BIOS build data.

BIOS Setup 41

System Time/System Date

Use this option to change the system time and date. Highlight Sys­tem Time or System Date using the < Arrow > keys. En ter new val­ues using the keyboard. Press the < Tab > key or the < Arrow >
keys to move between fields. The date must be entered in MM/
DD/YY format. The time is entered in HH:MM:SS format.

Note: The time is in 24-hour format. For example, 5:30 A.M. ap-

pears as 05:30:00, and 5:30 P.M. as 17:30:00.

Access Level

Displays the current system access level.

42 BIOS Setup

NuPRO-E340

5.3 Advanced BIOS Setup

Select the Advanced tab from the setup screen to enter the
Advanced BIOS Setup screen. You can select any of the items in
the left frame of the screen, such a s SuperIO Conf iguration, to go
to the sub menu for that item. You can display an Advanced BIOS
Setup option by highlighting it using the < Arrow > keys. The
Advanced BIOS Setup screen is shown below.

The sub menus are described on the following pages.

Launch PXE OpROM

Boot Option for Legacy Network Devices. Options: Enabled/
Disabled.

BIOS Setup 43

5.3.1 ACPI Settings

Enable APIC Auto Configuration

BIOS ACPI Auto Configuration. Options: Enabled/Disabled.

Enable Hibernation

Enable or disable the system's ability to hibernate (S4 sleep
state). This option may be not effective with some OS's.

ACPI Sleep State

Select the highest ACPI sleep state the system will enter, when
the SUSPEND button is pressed. Options: S1, S3, Suspend
Disable.

AC Power Shutdown

ATX mode: OS will turn off system power when shutdown.
AT mode: OS show It is now safe to turn off your computer.

AT mode will not support S3 & S4.

NOTE:

NOTE:

Lock Legacy Resources

Enable or disable Lock of Legacy Resources.

44 BIOS Setup

NuPRO-E340

5.3.2 Trusted Computing

Trusted computing is an industry standard to make personal com­puters more secure through a dedicated hardware chip, called a
Trusted Platform Module (TPM).

TPM Support

This option enables or disables the TPM support. System reset
is required. Options: Enabled/Disabled.

TPM State

Determine whether TPM state change requires Password
Authentication. Options: Enabled/Disabled.

Pending TPM Operation

Scheduled TPM operation. The settings for this value are
Enable, Disable and Clear.

BIOS Setup 45

5.3.3 CPU Configuration

Active Processor Cores

Number of cores to enable in processor. Options: All, 1, 2.

Limit CPUID Value Maximum

When Enabled, the processor will limit the maximum CPUID
input value to 03h when queried, even if the processor sup­ports a higher CPUID input value. When Disabled, the proces­sor will return the actual maximum CPUID input value of the
processor when queried. Enable this option to allow compatibil­ity with older operating systems.

Execute Disable Bit

Allows you to enable or disable the No-Execution Page Protec­tion Technology. Setting this item to [Disabled] forces the XD
feature flag to always return a z ero (0). Option s: Enabled, Dis­abled.

46 BIOS Setup

NuPRO-E340

Intel® Virtualization Tech

When enabled, Intel® Virtualization Technology (Intel® VT)
makes a single system appear as multiple independent sys­tems to software. This allows for multiple, independent operat­ing systems to be running simultaneously on a single system.

Power Technology

Sets the power management features. Options: Disable,
Energy Efficient, Custom.

Socket 0 CPU Information

BIOS Setup 47

5.3.4 SATA Configuration

SATA Mode

Options: IDE, RAID, AHCI.

Serial ATA Controller 0/1

Appears when SATA mode is set to IDE. This item specifies
whether Serial ATA Controller 0/1 is initialized in Compatible or
Enhanced mode of operation. The settings are Disabled, Com­patible and Enhanced.

Aggressive Link Power Management

Appears when SA TA mode is set to AHCI. The setting s are Dis­abled and Enabled.

SATA Port 0~5
The Staggered Spin-up, External SATA Port (eSATA) and

Hot Plug options appear when SATA Mode is set to AHCI.

Options: Enabled/Disabled.

48 BIOS Setup

NuPRO-E340

5.3.5 Intel TXT Configuration

Intel Trusted Execution Technology (Intel TXT) support can only
be enabled when TPM is enabled, if the CPU support s Safer Mode
Extensions (SMX), and Intel® Virtualization Technology (Intel®
VT) and Intel® Virtualization Technology for Directed I/O (VT-d)
are enabled.

BIOS Setup 49

5.3.6 Intel IGD SWSCI OpRegion

DVMT Mode

This item allows the user to enable or disable the DVMT func­tion.

DVMT/Fixed Memory

Select DVMT/Fixed memory size used by the Integrated
Graphics Device. Options: 128MB, 256MB, Maximum.

IGD - Boot Type

Select the video device which will be activated during POST.
This has no effect if an external graphics device is present.
Options: CRT+DVI, CRT, DVI.

Spread Spectrum Clock

IGD device spread spectrum clock function. Options: Enabled/
Disabled.

50 BIOS Setup

NuPRO-E340

5.3.7 USB Configuration

Legacy USB Support

Legacy USB Support refers to USB mouse and keyboard sup­port. Normally if this option is not enabled, any attached USB
mouse or USB keyboard will not become available until a USB
compatible operating system is fully booted with all USB driv­ers loaded. When this option is enabled, any attached USB
mouse or USB keyboard can control the system even when
there are no USB drivers loaded on the system. Set this value
to enable or disable the Legacy USB Support.

X Disabled: Set this value to prevent the use of any USB

device in DOS or during system boot.

X Enabled: Set this value to allow the use of USB devices

during boot and while using DOS.

X Auto: This option auto detects USB Keyboards or M ice and

if found, allows them to be utilized during boot and while
using DOS.

USB 3.0 Support

USB 3.0 Controller support. Options: Enable, Disable.

BIOS Setup 51

XHCI Hand-Off

This is a workaround for OSes without XHCI hand-off support.
The XHCI ownership change should be claimed by XHCI
driver. Options: En able, Disable.

EHCI Hand-Off

This is a workaround for OSes without EHCI hand-off support.
The EHCI ownership change should be claimed by EHCI
driver. Options: En able, Disable.

All USB Devices

Enabled/Disabled All USB devices. Options: Enable, Disable.

EHCI Controller 1/2

Enabled/Disabled USB 2.0 (EHCI) Support. Options: Enable,
Disable.

USB Port 0~13

Enabled/Disabled USB Port 0~13. Options: Enable, Disable.

Mass Storage Devices:

Mass storage device emulation type. 'AUTO' enumerates
devices according to their media format. Optical drives are
emulated as 'CDROM', drives with no media will be emulated
according to a drive type. Options: Auto, Floppy, Forced FDD,
Hard Disk, CD-ROM.

52 BIOS Setup

NuPRO-E340

5.3.8 Super IO Configuration

Serial Port1-6 Configuration

Enter the submenu for each serial port to enable/disable and
view the I/O port and IRQ settings.

Parallel Port Configuration

Enter the submenu to enable/disable the parallel port and
specify the base I/O port address.

BIOS Setup 53

5.3.9 Hardware Monitor

You can use this screen to view System Status information and to
select options for FAN1 settings (F AN2

Smart Fan 1 Mode Setting
Three operating modes are provided for FAN1: Full Mode, Auto-

matic Mode, and Manual Mode. Full Mode runs the fan at full

speed. Automatic Mode is Smart Fan mode. Manual Mode runs
the fan at the set speed (minimum is 0, maximum is 127).

Automatic Mode

In Automatic Mode, the following settings are visible.

is set to Full On by default

).

Fan Off Temperature Limit

Sets the temperature below which the fan will turn off in
degrees Celsius (°C). When the temperature is higher than the
set value, FAN1 will run at Fan Start PWM speed. When the
temperature is lower than the set value, FAN1 will stop.

Fan Start Temperature Limit

When the temperature in degrees (°C) is higher than the set
value, FAN1 will increase its speed according to the PWM
Slope Setting value.

54 BIOS Setup

NuPRO-E340

Fan Start PWM
Sets the PWM value of the fan between Fan Off Temperature

Limit and Fan Start Temperature Limit. Minimum value is 0

and maximum is 127.

PWMSlope Setting

The Slope PWM Value sets the rate of increase the fan speed
when the temperature is above Fan Start Temperature Limit.

System Status

System temperature, CPU temperature and fan speed (FAN1),
system voltages.

BIOS Setup 55

5.3.10 AMT Configuration

AMT

This item allows the user to Enable/Disable the Intel AMT func­tion.

Unconfigure AMT/ME

This item allows the user to unprovision the AM T/ME function
without a password.

Wat chDo g Time r

Options: Enabled/Disabled.

OS WatchDog Timer

Sets the OS WatchDog Timer (seconds).

BIOS WatchDog Timer

Sets the BIOS WatchDog Timer (seconds).

56 BIOS Setup

5.3.11 Serial Port Console Redirection

COM0/1 Console Redirection

Options: Enabled/Disabled.

NuPRO-E340

Console Redirection Settings

The settings specify how the host computer and the remote
computer exchange data. Both computers should have the
same or compatible settings.

BIOS Setup 57

Terminal Type

This option is used to select either VT100/VT-UTF8 or ANSI
terminal type. Options: VT100, VT100+, VT-UTF8, ANSI.

Bits per second

Select the bits per second you want the serial port to use for
console redirection. The options are 115200, 57600, 38400,
19200, 9600.

Data Bits

Select the data bits you want the serial port to use for console
redirection. Set this value to 7 and 8.

Parity

Set this option to select Parity for console redirection. The set­tings for this value are None, Even, Odd, Mark and Space.

Stop B its

Stop bits indicate the end of a serial data packet. (A start bit
indicates the beginning). The standard setting is 1 stop bit.
Communication with slow devices may require more than 1
stop bit. Set this value to 1 and 2.

Flow Control

Set this option to select Flow Control for console redirection.
The settings for this value are None, Hardware RTS/CTS.

Record Mode

With this mode enabled only text will be sent., allowing capture
of Terminal data. Set this value to Enabled or Disabled.

Resolution 100x31

Enable or disable extended terminal resolution. Set this value
to Enabled or Disabled.

Legacy OS Redirection Resolution

On a legacy OS, the number of Rows and Columns supported
by redirection. Set this value to 80x24 and 80x25.

58 BIOS Setup

NuPRO-E340

Serial Port for Out-of-Band Management

These settings control the ACPI serial port redirection table
(SPCR) which is used by Windows servers to provide Windows
Emergency Management Services (EMS) and is independent
from console redirection output. OoB Management or EMS
allows the remote management of selected components of
Windows servers, even when a server is not connected to the
network or the network is not available

Terminal Type

VT-UTF8 is the preferred terminal type for out-of-band man­agement. The next best choice is VT100+ and then VT100.
See above, in Console Redirection Settings page, for more
Help with Terminal Type/Emulation. Options: VT100, VT100+,

VT-UTF8, ASNI.
Bits per second

Select the bits per second you want the serial port to use fo r
console redirection. The options are 115200, 57600, 38400,
19200, 9600.

BIOS Setup 59

Flow Control

Set this option to select Flow Control for console redirection.
The settings for this value are None, Hardware RTS/CTS.

Data Bits

Displays the frame width for Out-of-Band Management.

Parity

Displays the parity for Out-of-Band Management.

Stop B its

Displays the number of stop bits for Out-of-Band Management.

60 BIOS Setup

NuPRO-E340

5.4 Chipset Setup

Select the Chipset tab from the setup screen to enter the Chipset
BIOS Setup screen. You can select any of the items in the left
frame of the screen to go to the sub m enu for t hat it em. T he C hip­set BIOS Setup screen is shown below.

BIOS Setup 61

5.4.1 Graphics and Memory Bridge Configuration

VT-d

Intel Virtualization Technology for Directed I/O. Options: Enabled/
Disabled.

Initial Graphics Adapter

Allows you to select which graphics controller to use as the pri­mary boot device. Options: IGD, PCI/IGD, PCI/PEG, PEG/IGD,
PEG/PCI.

IGD Memory

IGD shared memory size, Options: Disable/32M/64M/128M.

IGD Multi-Monitor

Multi-monitor support by the Internal Graphics Device. Options:
Enabled/Disabled

PCI Express Port

This option enables auto negotiation with a PEG device, disables
the use of the PEG port, or select enables use of the PEG port

62 BIOS Setup

NuPRO-E340

5.4.2 PCH Bridge Configuration

82574L LAN Controller

Controls the onboard Intel 82574L LAN controller. Options:
Enabled/Disabled.

Restore on AC Power Loss

Determines which state the computer enters when AC power is
restored after a power loss. The options for this value are Last
State, Power On and Power Off.

X Power Off: Set this value to always power off the system

while AC power is restored.

X Power On: Set this value to always power on the system

while AC power is restored.

X Last State: Set this value to power off/on the system depend-

ing on the last system power state while AC power is restored.

ALC626 HD Audio

Set this value to Enable/Disable the HD Audio Controller.

BIOS Setup 63

PCI Express Port Configuration

PCI Express Port 1~8

Configures the PCI Express ports in of the chipset. Options: Auto,
Enable, Disable.

PCIe Sub Decode

Enable or disable the PCIe Sub Decode port. This option is avail­able when the Subtractive Decode Agent is enable (PCH T r ap9[14])
= '1b'.

PCIE Ports 0-3 Configuration

Use this option to configure PCIe ports 0-3 of the PCH to "One x4
Port" or "Four x1 Ports".

The PCIE Ports 0-3 Configuration option is available in
BIOS version A1.6 and later.

NOTE:

NOTE:

64 BIOS Setup

5.4.3 Management Engine Subsystem

ME Subsystem

Options: Enabled/Disabled.

NuPRO-E340

ME Temporary Disable

Options: Enabled/Disabled (reset required).

End of POST Message

Options: Enabled/Disabled.

Execute MEBx

Options: Enabled/Disabled.

MEBx Mode

Options: Normal, Hidden Ctrl+P, Enter MEBx setup.

BIOS Setup 65

Integrated Clock Chip Configuration

ICC Enable

Integrated Clock Chip. Options: Enabled/Disabled.

66 BIOS Setup

NuPRO-E340

5.5 Boot Configuration

Select the Boot tab from the setup screen to enter the Boot BIOS
Setup screen. You can select any of the items in the left frame of
the screen, such as Boot Dev i ce Priority, to go to the sub menu for
that item. You can display a Boot BIOS setup option by highlight­ing it using the < Arrow > keys. The Boot Configuration screen is
shown below:

Setup Prompt Timeout

Number of seconds to wait for setup activation. 65535
(0xFFFF) means wait indefinitely.

Bootup NumLock State

This setting determines the state of t he NumLock function on
bootup. Options: On, Off.

Quiet Boot

When this feature is enabled, the BIOS will display the full­screen logo during the boot-up sequence, hiding normal POST
messages.

BIOS Setup 67

When it is disabled, the BIOS will display the normal POST
messages, instead of the full-screen logo.

Gate A20 Active

Options: Upon Request, Always.

Boot Option Priorities

Set the boot device options to determine the sequence in which
the computer checks which device to boot from.

Hard Drive BBS Priorities

The Boot devices are listed in groups by device type. First
press <Enter> to enter the sub-menu. You may then use the
arrow keys to select the desired device, then press <+>, <-> or
<PageUp>, <PageDown> key to move it up/down in the priority
list. For example, USB storage disks will be listed as "USB
Drives" in the sub-menu. Only the first device in each device gr

68 BIOS Setup

5.6 Security Setup

Password Support

NuPRO-E340

Two Levels of Password Protection

Provides both a Supervisor and a User password. If you use
both passwords, the Supervisor password must be set first.

The system can be configured so that all users must enter a
password every time the system boots or when Setup is exe­cuted, using either or either the Supervisor password or User
password.

The Supervisor and User passwords activate two different lev­els of password security. If you select password support, you
are prompted for a one to six character password. Type the
password on the keyboard. The password does not appear on
the screen when typed. Make sure you write it down. If you for­get it, you must drain NVRAM and re-configure.

BIOS Setup 69

Remember the Password

Keep a record of the new password when the password is
changed. If you forget the password, you must erase the sys­tem configuration information in NVRAM.

To access the sub menu for the following items, select the item
and press < Enter >:

X Change Administrator Password
X Change User Password
X Clear User Password

Administrator Password

Indicates whether a Administrator password has been set.

User Password

Indicates whether a user password has been set.

70 BIOS Setup

NuPRO-E340

5.7 Exit Menu

Select the Exit tab from the setup screen to enter the Exit BIOS
Setup screen. You can display an Exit BIOS Setup option by high­lighting it using the < Arrow > keys. The Exit BIOS Setup screen is
shown below.

Save Changes and Exit

When you have completed the system configuration changes,
select this option to leave Setup and reboot the computer so the
new system configuration parameters can take effect.

Save Configuration Changes and Exit Now?

[Ok] [Cancel]

appears in the window. Select Ok to save changes and exit.

BIOS Setup 71

Discard Changes and Exit

Select this option to quit Setup without making any permanent
changes to the system configuration.

Discard Changes and Exit Setup Now?

[Ok] [Cancel]

appears in the window. Select Ok to discard changes and exit.

Save Changes and Reset

Reset the system after saving the changes.

Discard Changes and Reset

Reset system setup without saving any changes.

Save Changes

Save changes made so far to any of the setup options.

Discard Changes

Select Discard Changes from the Exit menu and press < Enter >.
Select OK to discard changes.

Restore Defaults

Restore/Load Default values for all the setup options.

Save as User Defaults

Save the changes made so far as User Defaults.

Restore User Defaults

Restore the User Defaults to all the setup options.

Boot Override

This group of functions includes a list of devices within the boot
order. Select a drive to immediately boot that device regardless of
the current boot order. If you are booting to the EFI Shell, an exit
from the shell returns to Setup.

72 BIOS Setup

NuPRO-E340

Appendix A - Watchdog Timer

A sample program for configuring the NuPRO-E340’s watchdog
timer is included on the ADLINK All-in-One DVD in the following
directory: \NuPRO\NuPRO-E340\WDT.

A.1 Sample Code

#include<stdio.h>
#include<dos.h>

static unsigned int IT8783_ioPort = 0x2e;

void Enter_IT8783_Config(unsigned int flag)
{

if(flag) IT8783_ioPort = 0x4e;

switch(IT8783_ioPort)
{

case 0x2E: //Address port = 0x2E, enter keys =
0x87, 0x01, 0x55, 0x55

outportb(0x2E, 0x87);
outportb(0x2E, 0x01);
outportb(0x2E, 0x55);
outportb(0x2E, 0x55);

break;
case 0x4E: //Address port = 0x4E, enter keys =
0x87, 0x01, 0x55, 0xAA

outportb(0x4E, 0x87);

outportb(0x4E, 0x01);

outportb(0x4E, 0x55);

outportb(0x4E, 0xAA);

break;
default:

break;

}

}

void Exit_IT8783_Config(unsigned int flag)
{

if(flag) IT8783_ioPort = 0x4e;

outportb(IT8783_ioPort, 0x02);
outportb(IT8783_ioPort+1, 0x02);

Watchdog Timer 73

}

void Get_IT8783_ID(unsigned int &ID1, unsigned int &ID2)
{

outportb(IT8783_ioPort, 0x20);
ID1 = inportb(IT8783_ioPort+1);
outportb(IT8783_ioPort, 0x21);
ID2 = inportb(IT8783_ioPort+1);

}

void IT8783_WDTRun(unsigned int count_value, unsigned int

PLEDflag) //for NuPRO-E340

{

unsigned long tempCount;
unsigned int registerValue;

outportb(IT8783_ioPort, 0x07);
outportb(IT8783_ioPort+1, 0x07);// Device 7

outportb(IT8783_ioPort, 0xf8);
outportb(IT8783_ioPort+1, 0x00);// PLED mapping to

nothing, disable PLED function

if(PLEDflag == 1)
{

outportb(IT8783_ioPort, 0x27);
registerValue = inportb(IT8783_ioPort + 1);
registerValue |= 0x80; // set Pin09 is GPIO
function GP37
outportb(IT8783_ioPort+1, registerValue);

outportb(IT8783_ioPort, 0xc2);
registerValue = inportb(IT8783_ioPort + 1);
registerValue &= 0x7fb; // set GP37 is alternate
function
outportb(IT8783_ioPort+1, registerValue);

outportb(IT8783_ioPort, 0xca);
registerValue = inportb(IT8783_ioPort + 1);
registerValue |= 0x80; // set GP42 is output
outportb(IT8783_ioPort+1, registerValue);

74 Watchdog Timer

outportb(IT8783_ioPort, 0xf8);
outportb(IT8783_ioPort+1, 0x1f);// PLED mapping to
GP37

outportb(IT8783_ioPort, 0xf9);
registerValue = inportb(IT8783_ioPort + 1);
registerValue |= 0x02;
registerValue &= 0xfb;
outportb(IT8783_ioPort+1, registerValue);

}

outportb(IT8783_ioPort, 0x71);
registerValue = inportb(IT8783_ioPort + 1);
registerValue &= 0xfe;
outportb(IT8783_ioPort+1, registerValue);

outportb(IT8783_ioPort, 0x72);
registerValue = inportb(IT8783_ioPort + 1);
registerValue &= 0xdf;
outportb(IT8783_ioPort+1, registerValue);

if(count_value >= 60)
{

outportb(IT8783_ioPort, 0x72);
registerValue = inportb(IT8783_ioPort+1);
registerValue &= 0x8f;
registerValue |= 0x40; //enable WDT output through
PRST
outportb(IT8783_ioPort+1, registerValue); // set
WDT count is minute

NuPRO-E340

tempCount = count_value / 60;
if((count_value%60) > 30)

tempCount++;
if(tempCount > 65535)

tempCount = 65535;
printf("WDT timeout in %d minutes.\n", tempCount);

}
else
{

outportb(IT8783_ioPort, 0x72);

Watchdog Timer 75

registerValue = inportb(IT8783_ioPort+1);
registerValue |= 0x80;

tempCount = count_value;
if(tempCount != 0)
{

printf("WDT timeout in %d seconds.\n",

tempCount);

registerValue |= 0x40; //Enable WDT output

through KBRST
}
else
{

printf("WDT is Disabled.\n");
registerValue &= 0xbf; //Disable WDT output

through KBRST
}

outportb(IT8783_ioPort+1, registerValue); // set
WDT count is second

}

outportb(IT8783_ioPort, 0x71);
registerValue = inportb(IT8783_ioPort + 1);
registerValue |= 0x60; // set Mouse & Keyboard

interrupt Enable

outportb(IT8783_ioPort+1, registerValue);

outportb(IT8783_ioPort, 0x73);
outportb(IT8783_ioPort+1, tempCount); // set WDT count

LSB

}

76 Watchdog Timer

Appendix B - System Resources

B.1 System Memory Map

NuPRO-E340

Address Range

(decimal)

(4GB-2MB)

(4GB-18MB) –
(4GB-17MB-1)

(4GB-20MB) –
(4GB-19MB-1)

960 K – 1024 K F0000 – FFFFF 64 KB System BIOS Area

896 K – 960 K E0000 – EFFFF 64 KB Extended System BIOS Area

768 K – 896 K C0000 – DFFFF 128 KB

640 K – 768 K A0000 – BFFFF 128 KB Video Buffer & SMM space

0 K – 640 K 00000 – 9FFFF 640 KB DOS Area

Address Range

(hex)

FFE00000 –

FFFFFFFF

FEE00000 –

FEEFFFFF

FEC00000 –

FECFFFFF

Table B-1: System Memory Map

Size Description

2 MB High BIOS Area

1 MB FSB Interrupt Memory Space

1 MB APIC Configuration Space

PCI expansion ROM area
C0000 – C7FFF: Onboard VGA BIOS
CB800 – CC7FFF: Intel 82577LM
PXE option ROM when onboard LAN
boot ROM is enabled.

B.2 Direct Memory Access Channels

Channel Number Data Width System Resource

08-bits
18-bits
28-bits
38-bits

4 Reserved - cascade channel
5 16-bits Open
6 16-bits Open
7 16-bits Open

Parallel port
Parallel port

Diskette drive

Parallel port

(1)
(1)

(1)

(1)

Table B-2: Direct Memory Access Channels

Note (1): DMA channel 0, 1, or 3 will be occupied when using the parallel port.

System Resources 77

B.3 IO Map

Hex Range Device

000-01F DMA controller 1, 8237A-5 equivalent

020-02D and 030-03F Interrupt controller 1, 8259 equivalent

02E-02F,04E-04F LPC SIO (ITE8783) configuration index/data registers

040-042, 050-052 Timer, 8254-2 equivalent

060, 062, 064, 066 8742 equivalent (keyboard)

061 NMI control and status
070-077 Real Time Clock Controller (bit 7 -NMI mask)
080-091 DMA page register

092 Reset (Bit 0)/ Fast Gate A20 (Bit 1)
093-09F DMA page registers continued

0A0-0B1 and 0B4-0BD Interrupt controller 2, 8259 equivalent

0C0-0DF DMA controller 2, 8237A-5 equivalent

0F0

2E0 - 2F7 Serial Port 6
2E8 – 2EF Serial Port 4
2F0 – 2F7 Serial Port 5
2F8 – 2FF Serial Port 2

170-177 and 1F0-1F7

376 and 3F6

378 - 37F Parallel port

3B0 – 3BB Mono/VGA mode video

3C0- 3DF VGA registers
3E8 – 3EF Serial Port 3
3F8 – 3FF Serial Port 1

4D0 and 4D1 Interrupt controller

400 – 47F SB PM Base Address
500 – 57F SB GPIO
A00 – A3F SIO PME Base Address

CF9 Reset Control register (8 bit I/O)

1180 – 119F SMBus

Read: PCI and Master abort. (Note 1)

Write: FERR#/ IGNNE# /Interrupt controller

SATA controller or PCI

Table B-3: IO Map

Note:

A read to this address will subtractively go to PCI, where it will master abort.

78 System Resources

B.4 Interrupt Request (IRQ) Lines

IRQ Lines PIC Mode

NuPRO-E340

IRQ#

0 Counter 0 N/A No
1 Keyboard controller N/A No

2

3 Serial Port 2 (COM2)

4

5 PCI / ISA
6N/A N/A No
7 PCI / ISA
8 Real-time clock N/A No
9 SCI / PCI

10 PCI / ISA N/A No

11 PCI / ISA N/A No

12 PS/2 Mouse / PCI / ISA

13 Math Processor N/A No
14
15 PCI / ISA N/A No

Typical Interrupt

Resource

Cascade interrupt from

slave PIC

Serial Port 1 (COM1) /

PCI / ISA

Primary IDE controller /

PCI / ISA

Connected to Pin Available

N/A No

IRQ3 via SERIRQ, IRQ3

at ISA bus

IRQ4 via SERIRQ, IRQ4

at ISA bus

IRQ5 via SERIRQ, IRQ5

at ISA bus

IRQ7 via SERIRQ, IRQ7

at ISA bus

IRQ9 via SERIRQ, IRQ9

at ISA bus

IRQ12 via SERIRQ,

IRQ12 at ISA bus

IRQ14 via SERIRQ,

IRQ14 at ISA bus

Note (1)

Note (1)

Note (1)

Note (1)

Note (1), (2)

Note (1)

Note (1)

Table B-4: IRQ Lines PIC Mode

Notes:

(1) These IRQs can be used for PCI devices when the onboard device
is disabled. If the IRQ is from ISA, the user must reserve the IRQ for
ISA in the BIOS setup menu.

(2) The BIOS does not open the IRQ 9 setting for the ISA bus.

System Resources 79

IRQ Lines APIC Mode

IRQ#

0 System Timer N/A No
1 Keyboard controller N/A No
2 PCI / ISA N/A No

3

4

5

6

7
8 Real-time clock N/A No
9 ACPI-Compliant system

10 PCI / ISA

11 Serial Port 6 /PCI / ISA

12 PS/2 Mouse / PCI / ISA
13 Math Processor N/A No
14

15

16 N/A

17 N/A

T ypical Interrupt

Resource

Serial Port 2 (COM2) /

PCI / ISA

Serial Port 1 (COM1) /

PCI / ISA

Serial Port 3 (COM3) /

PCI / ISA

Serial Port 4 (COM4) /

PCI / ISA

Parallel Port / Serial

5 (COM5) / PCI / ISA

Primary IDE controller /

PCI / ISA

Secondary IDE

controller / PCI / ISA

Port

Connected to Pin Available

IRQ3 via SERIRQ,

IRQ3 at ISA bus

IRQ4 via SERIRQ,

IRQ4 at ISA bus

IRQ5 via SERIRQ,

IRQ5 at ISA bus

IRQ6 via SERIRQ No

IRQ7 via SERIRQ,

IRQ7 at ISA bus

IRQ9 via SERIRQ,

IRQ9 at ISA bus

IRQ10 via SERIRQ,

IRQ10 at ISA bus

IRQ11 via SERIRQ,

IRQ11 at ISA bus

IRQ12 via SERIRQ,

IRQ12 at ISA bus

IRQ14 via SERIRQ,

IRQ14 at ISA bus

IRQ15 via SERIRQ,

IRQ15 at ISA bus

PCIE Port 0/1/2/3/4/5/6/7,

P.E.G. Root Port, I.G.D,

EHCI Controller #2,

MEI Controller.

PCIE Port 0/1/2/3/4/5/6/7,

P.E.G. Root Port, KT Controller

Note (1)

Note (1)

Note (1)

Note (1)

Note (1), (2)

Note (1)

Note (1)

Note (1)

Note (1)

Note (1)

Yes

Yes

80 System Resources

NuPRO-E340

IRQ#

18 N/A

19 N/A

20 N/A
21 N/A PCI Slot 0, PCI Slot 4 No

22 N/A PCH HDA, PCI Slot 1 No
23 N/A EHCI Controller #1, PCI Slot 2 No

Typical Interrupt

Resource

Ta b le B-5: IRQ Lines AP IC Mode

Notes:

(1) These IRQs can be used for PCI devices when the onboard device
is disabled. If the IRQ is from ISA, the user must reserve the IRQ for
ISA in the BIOS setup menu.

(2) The BIOS does not open the IRQ 9 setting for the ISA bus.

Connected to Pin Available

PCIE Port 0/1/2/3/4/5/6/7,
P.E.G. Root Port, SATA Host
controller, SMBus Controller,

Thermal Controller,

SOL (COM7)

PCIE Port 0/1/2/3/4/5/6/7,
P.E.G. Root Port, SATA Host

controller, SATA Host

controller#1,

PCH internal GBE controller,

PCI Slot 3

Yes

Yes

No

System Resources 81

PCI Configuration Space Map

Bus # Device # Function # Routing Description

00h 00h 00h N/A Intel Host Bridge

00 02H 00H Internal Intel IGD
02 00H 0FFH N/A P.E.G. Port

00h 02h 00h Internal

00h 16h 00h Internal

00h 16h 01h Internal
00h 16h 02h Internal IDE-R controller

00h 16h 03h Internal P CI Serial controller
00h 19h 00h Internal GbE Controller
00h 1Ah 00h Internal Intel USB EHCI Controller #2
00h 1Bh 00h Internal High Definition Audio controller
00h 1Ch 00h Internal PCI Express Root port 1
00h 1Ch 01h Internal PCI Express Root port 2
00h 1Ch 02h Internal PCI Express Root port 3
00h 1Ch 03h Internal PCI Express Root port 4
00h 1Ch 04h Internal PCI Express Root port 5
00h 1Ch 05h Internal PCI Express Root port 6
00h 1Ch 06h Internal PCI Express Root port 7
00h 1Ch 07h Internal PCI Express Root port 8
00h 1Dh 00h Internal Intel USB EHCI Controller #1
00h 1Eh 00h N/A Intel PCI to PCI Bridge
00h 1Fh 00h N/A Intel LPC Interface Bridge
00h 1Fh 02h Internal Intel SATA controller #1
00h 1Fh 03h Internal Intel SMBus Controller
00h 1Fh 05h Internal Intel SATA controller #2
00h 1Fh 06h Internal Thermal Controller
11h 00h 0FFh Internal PCIE Port #0
12h 00h 0FFh Internal PCIE Port #1
13h 00h 0FFh Internal PCIE Port #2

Intel Integrated Graphics

Device

Intel Management Engine

Interface #1

Intel Management Engine

Interface #2

82 System Resources

NuPRO-E340

Bus # Device # Function # Routing Description

14h 00h 0FFh Internal PCIE Port #3
15h 00h 0FFh Internal Intel 82574L LAN Controller
16h 00h 0FFh Internal PCIE Port #5
17h 00h 0FFh Internal USB 3.0 Controller
18h 00h 0FFh Internal PCIE Port #7
20h 0Fh 00h Internal PCI Slot 0
20h 0Eh 00h Internal PCI Slot 1
20h 0Dh 00h Internal PCI Slot 2
20h 0Ch 00h Internal PCI Slot 3
20h 0Bh 00h Internal PCI Slot 4

Table B-6: PCI Configuration Space Map

System Resources 83

PCI Interrupt Routing Map

PIRQ A B C D E F G H

INT Line INTA INTB INTC INTD

P.E.G. Root Port INTA INTB INTC INTD

VGA X

SATA Controller X X

SATA Controller 1 X

SMBus controller X

Thermal Controller X

EHCI 1 X
EHCI 2 X

HDA X

Intel GBE X
HECI host 1 X
HECI host 2 X

IDER Controller X

KT Controller X

PCIE port 0 INTA INTB INTC INTD
PCIE port 1 INTB INTC INTD INTA
PCIE port 2 INTC INTD INTA INTB
PCIE port 3 INTD INTA INTB INTC
PCIE port 4 INTA INTB INTC INTD
PCIE port 5 INTB INTC INTD INTA
PCIE port 6 INTC INTD INTA INTB
PCIE port 7 INTD INTA INTB INTC

PCI Slot 0 X
PCI Slot 1 X
PCI Slot 2 X
PCI Slot 3 X
PCI Slot 4 X

Table B-7: PCI Interrupt Routing Map

84 System Resources

NuPRO-E340

Important Safety Instructions

For user safety, please read and follow all instructions,
WARNINGS, CAUTIONS, and NOTES marked in this manual

and on the associated equipment before handling/operating the
equipment.

X Read these safety instructions carefully.
X Keep this user’s manual for future reference.
X Read the specifications section of this manual for detailed

information on the operating environment of this equipment.

X When installing/mounting or uninstalling/removing

equipment:

Z Turn off power and u nplug any power cords/cables.

X To avoid electrical shock and/or damage to equipment:

Z Keep equipment away from water or liquid sources;
Z Keep equipment away from high heat or high humidity;
Z Keep equipment properly ventilated (do not block or

cover ventilation openings);

Z Make sure to use recommended voltage and powe r

source settings;

Z Always install and operate equipment near an easily

accessible electrical socket-outlet;

Z Secure the power cord (do not place any obje ct on /ove r

the power cord);

Z Only install/attach and operate equipment on stable

surfaces and/or recommended mountings; and,

Z If the equipment will not be used for long periods of time,

turn off and unplug the equipment from its power source.

Important Safety Instructions 85

X Never attempt to fix the equipment. Equipmen t sho u ld on ly

be serviced by qualified personnel.

A Lithium-type battery may be provided for uninterrupted, backup
or emergency power.

Risk of explosion if battery is replaced with one of an incorrect

WARNING:

type. Dispose of used batteries appropriately.

X Equipment must be serviced by authorized technicians

when:

Z The power cord or plug is damaged;
Z Liquid has penetrated the equipment;
Z It has been exposed to high humidity/moisture;
Z It is not functioning or does not function according to the

user’s manual;

Z It has been dropped and/or damaged; and/or,
Z It has an obvious sign of breakage.

86 Important Safety Instructions