ACTi KCM-7311 User Manual
Encoder Firmware V4.06.09 User’s Manual
Outdoor Dome KCM Series
Hardware Manual
KCM-7311
KCM-7111
2014/01/27
www.acti.com
Hardware Manual
Table of Contents
Precautions ............................................................. 4
Safety Instructions .................................................................................... 5
Introduction ............................................................. 6
The List of Models ..................................................................................... 6
Package Contents ...................................................................................... 7
Physical Description ................................................................................. 8
Mounting Solutions ................................................................................. 10
Installing the Camera on a Surface ..................... 11
Step 1: Drill the Holes ............................................................................... 11
Step 2: Open the Dome Cover ................................................................ 12
Step 3: Prepare for Waterproof Installation ........................................... 13
Waterproof Solution with Naked Cable ................................................. 14
Waterproof Solution with Conduit .......................................................... 16
Step 4: Install the Camera to the Surface .............................................. 20
Step 5: Connect the Cable(s) .................................................................. 21
Step 6: Access the Camera Live View .................................................... 21
Step 7: Adjust the Viewing Angle and Focus ........................................ 22
Step 8: Close the Dome Cover ................................................................ 22
Other Connections................................................ 23
Connecting a Power Adapter (Optional) ................................................ 23
Connecting DI/DO Devices (Optional) .................................................... 25
Connecting Audio In / Out Devices (Optional) ...................................... 28
2
www.acti.com
Hardware Manual
Other Adjustments ................................................ 29
How to Adjust Focus and Viewing Angle ............................................... 29
KCM-7311 ............................................................................................. 29
KCM-7111 ............................................................................................. 31
Accessing the Camera ......................................... 32
Connect the Equipment .......................................................................... 32
Configure the IP Addresses .................................................................... 32
Access the Camera .................................................................................. 37
3
www.acti.com
Hardware Manual
Precautions
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to follow
the safety instruction given may directly endanger people, cause damage to the system or to
other equipment.
Servicing
Do not attempt to service this video device yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your local
office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.
FCC/CE Regulation
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the users will be required to correct the interference at their own
expense.
4
www.acti.com
Hardware Manual
Safety Instructions
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may cause
hazards.
Do not use accessories not recommended by the manufacturer
Only install this device in a dry place protected from weather
Servicing
Do not attempt to service this video product yourself. Refer all servicing to qualified service
personnel.
Damage Requiring service
Disconnect this video product from the power supply immediately and refer servicing to qualified
service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the inner parts of video product have been directly exposed to rain or water.
4) If the video product does not operate normally by following the operating Instructions in this
manual. Adjust only those controls that are covered by the instruction manual, as an improper
adjustment of other controls may result in damage, and will often require extensive work by a
qualified technician to restore the video product to its normal operation.
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine if the video product is in proper operating condition.
5
www.acti.com
Hardware Manual
KCM-7111
5MP Indoor Zoom Dome with D/N, Adaptive IR, Basic WDR,
3x Zoom lens
KCM-7311
2MP Indoor Zoom Dome with D/N, Adaptive IR, Basic WDR, SLLS,
3x Zoom lens
Introduction
The List of Models
This hardware manual contains the following models:
From the installation perspective these models are very similar; therefore you can use one manual
for them.
6
www.acti.com
Hardware Manual
Camera
Conduit Gland
Cable Gland
Hexagon Wrench
Pan Bracket Wrench
Mounting Screw Kit
Terminal Block
(for Power)
Terminal Block
(for DIO/DO)
Terminal Block
(for Audio-In/Out)
Quick Installation Guide
Warranty Card
Drill Template
Drill Template
Package Contents
Check if the camera package comes with the following items.
7
www.acti.com
Physical Description
KCM-7111
Hardware Manual
KCM-7311
8
www.acti.com
Hardware Manual
1) Power Button
Press the Power Button to reboot the camera.
2) Ethernet Port
The Ethernet Port connects to a network using a standard Ethernet cable.
3) Memory Card Slot
Insert a Micro SDHC card here for local recording on the camera.
4) Reset Button
The Reset Button is used to restore the default factory settings of the camera.
Step 1: Disconnect the power supply.
Step 2: Press and continue to hold the Reset Button (with a sharp object, like a pen.)
Step 3: Connect the power supply while keeping the Reset Button pressed.
Step 4: Wait for 45 seconds and then release the Reset Button.
5) Digital Input / Output
This connector connects to digital input or output devices, such as an alarm trigger, panic
button,etc. Digital Input (DI) and Digital Output (DO) devices are used in applications like motion
detection, event triggering, alarm notifications, etc. See Connecting DI/DO Devices (Optional)
on page 25 for information.
6) DC 12V Power Input
In case the camera is connected to a non-PoE (Power over Ethernet) switch, use this connector
to connect the camera to an external power adapter. See Connecting a Power Adapter
(Optional) on page 23 for more information.
7) Audio Input / Output
This connector connects to audio input or output devices, such as a microphone or speaker. See
Connecting Audio In / Out Devices (Optional) on page 28 for more information.
9
www.acti.com
Hardware Manual
Mount Types
Accessories
Surface
Mount
Use the mounting screw kit included in the
camera package; no additional accessories
are required. See
Installing the Camera on a Surface on
page 11 for installation instructions.
Flush Mount
PMAX-1003
L Type Wall
Mount
PMAX-0308
Pendant
Mount
PMAX-0101+ PMAX-0103
Mounting Solutions
There are several mounting options that you can use to install the camera. Below are the most
common options:
For more information about mounting solutions and accessories, please visit to our website
http://www.acti.com/mountingselector.
10
www.acti.com
Hardware Manual
Installing the Camera on a Surface
NOTE: This manual is used by several camera models having the same camera installation
procedures although the camera module itself may vary. Therefore the camera images on this
documentation may differ from the actual camera that you received.
Step 1: Drill the Holes
1. Using the supplied drill template, mark the screw holes location on the surface, then drill the
holes and insert the plastic plugs.
2. Determine how the cables will be routed: pass through the surface or along the surface.
If the cables will pass through the surface:
a. Mark and drill the conduit hole location on the surface as shown on the drill
template.
b. Remove the metal cap covering the bottom conduit hole of the camera, and
attach the cap to the side conduit hole to close it. Route the network cable to
pass this hole from the surface.
If the cables will be routed along the surface, skip to the next step.
11
www.acti.com
Hardware Manual
Step 2: Open the Dome Cover
1. Remove the plastic covering the camera.
2. Loosen the three (3) screws securing the dome cover.
3. Carefully lift to open the dome cover and place it on the side of the camera.
NOTE: Do not abruptly lift the dome cover; it is attached to the camera with a spring wire.
12
Loading...