KCM-5611
18x Zoom H.264 2-Megapixel IP IR D/N
PoE Outdoor Box Camera with Advanced
WDR
Hardware User’s Manual
(DC 12V / PoE)
Ver. 2012/8/9
www.acti.com
KCM-5611 Hardware User’s Manual
Table of Contents
0. Precautions 3
1. Introduction 4
Package Contents ........................................................................... 4
Features and Benefits ..................................................................... 5
Safety Instructions .......................................................................... 6
Physical description ........................................................................ 8
Preparing for Installation ............................................................. 11
How to Do the Waterproof Installation ....................................... 11
Basic Connections ......................................................................... 15
Product Specification .................................................................... 16
2. Accessing Camera 18
If you have DHCP server / router in your network: ...................... 18
If you do
NOT
have DHCP server / router in your network: ......... 18
2
www.acti.com
KCM-5611 Hardware User’s Manual
0. Precautions
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to
follow the safety instruction given may directly endanger people, cause damage to the system
or to other equipment.
Servicing
Do not attempt to service this video device yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your
local office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.
FCC/CE Regulation
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the users will be required to correct the
interference at their own expense.
3
www.acti.com
KCM-5611 Hardware User’s Manual
1. Introduction
Package Contents
KCM-5611 QIG
Terminal Blocks for Power, DI/O and
Serial Port Warranty Card
4
www.acti.com
KCM-5611 Hardware User’s Manual
Features and Benefits
This is a cutting edge network video surveillance camera. It can capture, compress and
transmit real time video in excellent quality (15 FPS 2 Megapixel, 1920 x 1080). This camera is
your best choice to build an intelligent IP surveillance system.
18x Zoom Lens with Auto Focus
The powerful 18x Zoom Lens with ISP enabled Auto Focus brings precision video quality not
available with manual adjustments. Focus is no longer an issue during installation, saving time
while enhancing quality.
Adaptive Profile
With the innovative embedded Image Signal Processor (ISP), this camera responds to
changing lighting condition with customized algorithm. This allows for clear image with very
little noise at night.
H.264/MPEG-4/MJPEG Triple Codec Dual Streaming
This device supports 3 compression formats, H.264, MPEG-4 and MJPEG. It brings superior
image quality at 15 frames per second in Full HD 1080p (1920 x 1080). In 720p (1280 x 720)
and VGA resolution (640 x 480) the device reaches 30 frames per second.
Advanced WDR
Advanced WDR technology is the most advanced approach of improving the dynamic range of
the camera. While many other WDR technologies enhance the dynamic range while producing
noise, blur edges of objects and untrue colors, Advanced WDR is designed to improve the
dynamic range while keeping the true colors, sharp edges of objects and free from noise
DC Iris Control
With DC Iris Lens, this camera automatically adjusts incoming light levels to achieve the best
video performance. Wildly fluctuating outdoor lighting condition is no longer an issue with your
video quality.
5
www.acti.com
KCM-5611 Hardware User’s Manual
Powerful Bundled Surveillance Software
To extend the capabilities of the IP Box Camera series, a powerful surveillance program is
included in the package for free. Users can easily use an existing PC as a digital video recorder.
Scheduled recording and manual recording keep every important video recorded in the local
hard disk. Reliable and accurate motion detection with instant warning enables immediate
response in every condition. Quick and simple search and playback function lets you easily find
the images and video you want.
Software Development Kit Support
This IP Box Camera can be integrated or controlled by applications from third party software
developers. Software developers can save considerable efforts by using our Streaming Library
or ActiveX control.
Safety Instructions
Don’t use the power supply with other voltages
This device is likely to be damaged or damage other equipments / personnel, if you use a
power supply with different voltage than the one included with this device. All warranty of this
product will be voided in the situations above.
Don’t open the housing of the product
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may
cause hazards.
Water and Moisture
Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool and the like.
Don’t use accessories not recommended by the manufacturer
Only install this device and the power supply in a dry place protected from weather
6
www.acti.com
KCM-5611 Hardware User’s Manual
Servicing
Do not attempt to service this video product yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Damage Requiring service
Disconnect this video product from the power supply immediately and refer servicing to
qualified service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the video product has been directly exposed to rain or water.
4) If the video product does not operate normally by following the operating Instructions in
this manual. Adjust only those controls that are covered by the instruction manual, as an
improper adjustment of other controls may result in damage, and will often require
extensive work by a qualified technician to restore the video product to its normal
operation.
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine if the video product is in proper operating condition.
7
www.acti.com
KCM-5611 Hardware User’s Manual
Physical description
1) Micro SD / Micro SDHC Card Slot*
Insert your Micro SD card here for local recording on camera
2) Power LED
This LED light will indicate current camera status.
3) Audio Input / Output
The IP device supports audio input and output with earphone jack
4) Power Input
If you use Power Adaptor to run the device, please connect the power adaptor to the terminal
block in the way shown below.
5) Serial Port
This port connects to serial devices via RS-485 or RS-232 protocols.
8
www.acti.com
Pin Number
RS422
RS485
1
TX+
D+ 2 TX-
D- 3 RX+
N.C.
4
RX-
N.C,
On (3s)
On
1s
Power On
About 20 Seconds
Stay On
Off (about 15s)
Off (10~15s)
Restore to Default
Complete
KCM-5611 Hardware User’s Manual
6) Reset Button
Step 1: Switch off IP device by disconnecting the power cable
Step 2: Press and continue to hold the Reset Button (with a sharp tipped object, like a pen.)
Step 3: Reconnect the power cable while continuing to hold the reset button. The red
Power LED light will flash on for 3 second first, turn off for about 15 seconds, flash on for
another second and turn off again. By this time the reset to default operation is already
completed. This will take around 20 seconds from power up. You may then release the
reset button. This length of time fluctuates slightly with the environment. The Power LED light
will come back on and stay on after a few more seconds. The unit will start up with factory
default settings automatically.
7) Ethernet Port
The IP device connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this
IP device can auto detect the speed of local network segment (10Base-T/100Base-TX
Ethernet).
8) Digital Input / Output
Used in applications like motion detection, event triggering, time lapse recording, alarm
notifications, etc., the I/O terminal connector provides the interface to:
9
www.acti.com
1
2
3
FUSE 1A
NPN
DC TO DC
DI
DO
3.3V
DC POWER
GND
1
2
3
4
CONVERTER
EARTH GND
DO
DI
RELAY
SW
DIODE
DEVICE
-
+
POWER INPUT
CAMERA
KCM-5611 Hardware User’s Manual
• 1 Transistor Outputs - For connecting external devices such as relays and LEDs.
Connected devices can be activated by Output buttons on the Live View page or through video
management software. Connect DO1 and DO2 to their closest 12V pin to activate.
• 2 Digital Inputs - An alarm input for connecting devices that can toggle between an open
and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. The
device will detect the change in digital input and transmit the signal to video surveillance
servers. The I/O terminal pins are numbered right to left,
Connect input/output devices to the camera as follows:
1. Attach the cables for the device securely to the supplied green connector block. Connect DI
pins to GND pins, and DO pins to 12V pins. Link pins 1/3, 2/4, 5/7,6/8.
2. Once cables are connected, push connector block into the terminal connector on camera.
10
www.acti.com
KCM-5611 Hardware User’s Manual
Preparing for Installation
Remove the back cover by unscrewing the four attachments.
How to Do the Waterproof Installation
The following installation procedure makes the camera be water-resistant even for the
situations where the camera can easily be flooded by pouring rain.
The important part to focus on during the installation:
The protection of the cabling has to be done by a proper flex
conduit. The size of the flex conduit that matches with the
conduit gland is 3/8”. (Not included in the package)
The following images show the step-by-step procedure of completing the water-proof
installation.
1. Disassemble the conduit gland as shown on
the photo.
2. Pull the network cable through the flex
conduit. Please note that the size of the conduit
and the gland is big enough to let the RJ-45
connector pass through all the way.
11
www.acti.com
KCM-5611 Hardware User’s Manual
3. Two pieces from the conduit gland set will be
attached to flex conduit first.
4. The third piece goes through the back side
cover of the camera.
5. The fourth piece (locking nut) is used to lock
the gland firmly from the inside of the back side
cover.
6. Pull the network cable through the back side
cover of the camera.
12
www.acti.com
KCM-5611 Hardware User’s Manual
7. Connect the flex conduit to the back side
cover of the camera.
8. Tighten the domed sealing nut.
9. Plug the network cable into the camera’s
RJ-45 connector before closing the back side
of the camera. If you are not using PoE and
need an additional power cord then please
connect it at this stage, too.
10. Tighten the screws of the back side of the
camera properly.
13
www.acti.com
KCM-5611 Hardware User’s Manual
11. Finally, the box camera with properly
mounted flex conduit as well as with proper
outdoor bracket would look like this.
14
www.acti.com
KCM-5611 Hardware User’s Manual
Basic Connections
Follow the procedures below to connect the IP device to the respective apparatuses.
If you have a PoE(Power over Ethernet) supported switch or injector:
1) Connect your IP Box Camera to the Switch / Injector by CAT5 or CAT6 cables with RJ45
connector.
2) Connect your Switch / Injector to PC with another CAT5 / CAT6 network cable.
If your switch does not support PoE, and you are powering the camera with power
adaptor:
1) Connect the power adaptor to IP Box Camera
2) Connect IP device’s Ethernet port to Network switch (via RJ45 connectors).
Connect a PC to the Ethernet switch (via RJ45 connectors)
Please refer to our PoE Guide for more details on Power over Ethernet related concepts.
15
www.acti.com
KCM-5611 Hardware User’s Manual
KCM-5611
• Device
Device Type Box Camera
Image Sensor Progressive Scan CMOS
Sensor Size 1/2.8" (5.42 x 3.41 mm)
Horizontal Resolution 974 TVL
Day / Night Yes
Minimum Illumination
Color: 0.1 lux at F1.6 (30 IRE, 2400 °K)
B/W: 0 lux (IR LED on)
Color to B/W switch ISP based switch, configurable
Mechanical IR Cut Filter Yes
IR Sensitivity Range 700 - 1100 nm
IR LED IR LED x 24 (850 nm)
Electronic Shutter
1/13 - 1/2000 sec (50Hz); 1/15 - 1/2000 sec (60Hz) (manual mode)
1 - 1/2000 sec (auto mode
• Lens
Focal Length Zoom, f4.7 - 84.6 mm / F1.6 - 2.8
Zoom Ratio 18x optical
Iris DC Iris
Focus Auto Focus
Horizontal Viewing Angle 48.94°- 3.61°
• Video
Compression H.264, MPEG-4 SP, MJPEG
Maximum Frame Rate
vs. Resolution (H.264, MJPEG)
15 fps at 1920 X 1080 (HD 1080p); 30 fps at 1280 x 720 (HD 720p); 30 fps at
640 x 480 (VGA)
Maximum Frame Rate
vs. Resolution (MPEG-4 SP)
11 fps at 1920 X 1080 (HD 1080p); 25 fps at 1280 x 720 (HD 720p); 30 fps at
640 x 480 (VGA)
Multi-Streaming Simultaneous dual steams based on two configurations
Bit Rate 28 Kbps - 6 Mbps (per stream)
Bit Rate Mode Constant, Variable
Image Enhancement
ExDR (Extreme Dynamic Range); White balance: automatic, hold and manual;
Brightness; Saturation; Contrast; Sharpness; Automatic gain control; 2D+3D Digital
noise reduction; Flickerless; Defogging
Privacy Mask 4 configurable regions
Text Overlay User defined text on video
Image Orientation Image flip and mirror
• Audio
Compression 8 kHz, Mono, PCM, 16 bit encoding
Audio-In 3.5mm Phone Jack
Audio-Out 3.5mm Phone Jack
Product Specification
16
www.acti.com
• Network
Protocol & Service
TCP, UDP, HTTP, HTTPS, DHCP, PPPoE, RTP, RTSP, IPv6, DNS, DDNS, NTP,
ICMP, ARP, IGMP, SMTP, FTP, UPnP, SNMP, Bonjour, Pelco-D
Ethernet Port 1, Ethernet (10/100 Base-T), RJ-45 connector
Security
IP address filtering; HTTPS encryption; Password protected user levels; IEEE
802.1X network access control
• Alarm
Alarm Trigger Video motion detection (3 regions); External device through digital input
Alarm Response
Notify control center; Go to Zoom preset point or preset tour; Change camera
settings; Command other devices; E-mail notification with snapshots; Save video
or snapshot to local storage; Upload video, snapshot to FTP server; Activate
external device through digital output
• Interface
Digital Input 2, terminal block
Digital Output 2, terminal block
Serial Port RS-485, RS-422, terminal block
Local Storage MicroSD/SDHC memory card slot (card not included)
• General
Power Source / Consumption PoE Class 3 (IEEE802.3af) / 7.68W (IR on)
DC 12V / 9.6W (adapter not included)
Weight 1324g ( 2.92 lb)
Dimensions (W x H x D) 115.20 mm x 130.59 mm x 195.00 mm (4.50” x 5.10” x 7.70”)
Operating Temperature -30°C ~ 50°C (-22°F ~ 122°F)
Operating Humidity 10% ~ 85% RH
Approvals Camera: CE, FCC, IP66
• Integration
Unified Solution Fully compatible with ACTi software
ISV Integration Software Development Kit (SDK) available
Firmware Access Browser Microsoft Internet Explorer 6.0 or newer
KCM-5611 Hardware User’s Manual
17
www.acti.com
KCM-5611 Hardware User’s Manual
2. Accessing Camera
If you have DHCP server / router in your network:
Many network server / routers are able to automatically provide IP addresses through DHCP. If
you are using such a network, just plug in your computer and IP Box Cam into the network and
your IP device will acquire network address by itself. Find and access the device with our IP
Utility program. You may download it at:
http://www.acti.com/product/detail/Software/ACTi_Utility_Suite
If you do
NOT
have DHCP server / router in your
network:
1. Configure your PC to use the same subnet by changing your PC’s IP address to the
subnet with prefix 192.168.0.XXX. The last number should be anything from 1 to 254
except 100 and other occupied IP addresses. Subnet mask should be 255.555.255.0.
2. The default IP used by this device is 192.168.0.100. Please make sure your PC is
NOT using this address and that no two equipments use the same IP address in
the network.
3. Change your IP address by going to Control Panel ->Manage Network Connections ->
Right click on the connection to change -> Option -> TCP/IP IPv4 Properties.
18
www.acti.com
Please set the settings as below.
IP address: 192.168. 0.xxx
Subnet mask: 255.255.255.
0
(NOTE: xxx should be a number
from 1 to 254 except 100, which is
used by the IP device. Please also
make sure that no two equipments
use the same IP address in the
KCM-5611 Hardware User’s Manual
4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP:
192.168.0.100
5. When you see the login window, please input default user and password:
Default User: Admin Password: 123456
6. After logging in, you will see the video from camera. To go to the main menu, click the
“Setup” button on the top left.
19
www.acti.com
KCM-5611 Hardware User’s Manual
If you are using a single camera, this is enough to access the device.
If you are using multiple devices, you need to change the current device to another
unused IP address, so that when the next device is connected to the network, no two
devices use the same IP. Please perform the following steps.
7. Go to IP Settings-> Connection Type
8. Change the IP mode to Static.
9. Change the IP to 192.168.0.101 or any other unused IPs. Do NOT use the PC’s IP
address or 192.168.0.100.). If this is not the first device you add to the network, please
also avoid other devices’ IPs.
20
www.acti.com
10. Click “Apply”
KCM-5611 Hardware User’s Manual
11. Please go to System -> Save & Reboot, and click “Apply”. Internet Explorer will close
after a few seconds. This is normal.
12. Wait for 30 seconds, and open IE again to connect to the new IP. (In this example,
192.168.0.101). For the second device or more you add into the network, please type
the correct IP.
13. Adjust the default Video setting by going to Video & Audio -> Video Compression
21
www.acti.com
KCM-5611 Hardware User’s Manual
22
Loading...