Acer X112, X1161PN User Manual

Page 1

Acer Projector

X1161P/X1161PA/X1161PN/X112/
X1261P/X1261PN Series
User's Guide
Page 2
Copyright © 2012. Acer Incorporated. All Rights Reserved.
Acer Projector X1161P/X1161PA/X1161PN/X112/X1261P/X1261PN Series User's Guide Original Issue: 11/2012
Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications. This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims the implied warranties of merchantability or fitness for a particular purpose.
Record the model number, serial number, purchase date and place of purchase information in the space provided below. The serial number and model number are recorded on the label affixed to your projector. All correspondence concerning your unit should include the serial number, model number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronically, mechanically, by photocopy, recording or otherwise, without the prior written permission of Acer Incorporated.
Acer Projector X1161P/X1161PA/X1161PN/X112/X1261P/X1261PN Series
Model number: __________________________________
Serial number: ___________________________________
Date of purchase: ________________________________
Place of purchase: ________________________________
Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies' product names or trademarks are used herein for identification purposes only and belong to their respective companies.
Page 3

Information for your safety and comfort

Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Caution for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to the external power supply unit:
Install the power supply unit before connecting the power cord to the AC
power outlet.
Unplug the power cord before removing the power supply unit from the
projector.
If the system has multiple sources of power, disconnect power from the
system by unplugging all power cords from the power supplies.
Caution for Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power to the equipment, be sure to unplug the power cord from the electrical outlet.
iii
Warnings!
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. If the product
falls, it could be seriously damaged.
Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation is provided.
Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind onto or into the product.
Page 4
iv
To avoid damage of internal components and to prevent battery leakage,
do not place the product on a vibrating surface.
Never use it under sporting, exercising, or any vibrating environment
which will probably cause unexpected short current or damage rotor devices, lamp.
Using electrical power
This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult your dealer or local power company.
Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord.
If an extension cord is used with this product, make sure that the total
ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating.
Do not overload a power outlet, strip or receptacle by plugging in too
many devices. The overall system load must not exceed 80% of the branch circuit rating. If power strips are used, the load should not exceed 80% of the power strip's input rating.
This product's AC adapter is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet is properly grounded before inserting the AC adapter plug. Do not insert the plug into a non-grounded power outlet. Contact your electrician for details.
Warning! The grounding pin is a safety feature. Using a power outlet that is not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected noise produced by other nearby electrical devices that may interfere with the performance of this product.
Use the product only with the supplied power supply cord set. If you need
to replace the power cord set, make sure that the new power cord meets the following requirements: detachable type, UL listed/CSA certified, VDE approved or its equivalent, 4.5 meters (15 feet) maximum length.
Page 5
Product servicing
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service personnel when:
the power cord or plug is damaged, cut or frayed
liquid was spilled into the product
the product was exposed to rain or water
the product has been dropped or the case has been damaged
the product exhibits a distinct change in performance, indicating a need
for service
the product does not operate normally after following the operating
instructions
Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition.
Warning! For safety reasons, do not use non-compliant parts when adding or changing components. Consult your reseller for purchase options.
v
Your device and its enhancements may contain small parts. Keep them out of the reach of small children.
Additional safety information
Do not look into the projector's lens when the lamp is on. The bright may
hurt your eyes.
Turn on the projector first and then signal sources
Do not place the product in following environments:
Space that is poorly ventilated or confined. At least 50cm clearance from walls and free flow of air around the projector is necessary.
Locations where temperatures may become excessively high, such as inside of a car with all windows rolled up.
Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shortening the life span and darkening the image.
Locations near fire alarms.
Locations with an ambient temperature above 40 ºC/104 ºF.
Locations where the altitudes are higher than 10000 feet.
Unplug immediately if there is something wrong with your projector. Do
not operate if smoke, strange noise or odor comes out of your projector. It
Page 6
vi
might cause fire or electric shock. In this case, unplug immediately and contact your dealer.
Do not keep using this product to break or drop it. In this case contact your
dealer for inspection.
Do not face the projector lens to the sun. It can lead to fire.
When switching the projector off, suggest to ensure the projector
completes its cooling cycle before disconnecting power.
Do not frequently turn off the main power abruptly or unplug the
projector during operation. The best way is to wait for the fan to turn off before turning main power off.
Do not touch air outlet grille and bottom plate which becomes hot.
Clean the air filter frequently if have. The temperature inside may rise and
cause damage when the filter/ventilation slots clogged with dirt or dust.
Do not look into the air outlet grille when projector is operating. It may
hurt your eyes.
Always open the lens shutter or remove the lens cap when the projector is
on.
Do not block the projector lens with any object when the projector is
under operation as this could cause the object to become heated and deformed or even cause a fire. To temporarily turn off the lamp, press HIDE on the remote control.
The lamp becomes extremely hot during operation. Allow the projector to
cool for approximately 45 minutes prior to removing the lamp assembly for replacement.
Do not operate lamps beyond the rated lamp life. It could cause it to break
on rare occasions.
Never replace the lamp assembly or any electronic components unless the
projector is unplugged.
The product will detect the life of the lamp itself. Please be sure to change
the lamp when is showing warning message.
When changing the lamp, please allow unit to cool down, and follow all
changing instructions.
Reset the "Lamp Hour Reset" function from the Onscreen display
"Management" menu after replacing the lamp module.
Do not attempt to disassemble this projector. There are dangerous high
voltages inside which may hurt you. The only user serviceable part is the lamp which has its own removable cover. Refer servicing only to suitable qualified professional service personnel.
Do not stand the projector on end vertically. It may cause the projector to
fall over, causing injury or damage.
This product is capable of displaying inverted images for ceiling mount
installation. Only use acer ceiling mount kit for mounting the projector and ensure it is securely installed.
Page 7
vii
Caution for Listening
To protect your hearing, follow these instructions.
Increase the volume gradually until you can hear clearly and comfortably.
Do not increase the volume level after your ears have adjusted.
Do not listen to music at high volumes for extended periods.
Do not increase the volume to block out noisy surroundings.
Decrease the volume if you can't hear people speaking near you.
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle. For more information on the Waste from Electrical and Electronics Equipment (WEEE) regulations, visit http://www.acer-group.com/public/ Sustainability/sustainability01.htm
Mercury advisory
For projectors or electronic products containing an LCD/CRT monitor or display:
“Lamp(s) contain Mercury, Dispose Properly.”
Lamp(s) inside this product contain mercury and must be recycled or disposed of according to local, state or federal laws. For more information, contact the Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal information, check www.lamprecycle.org
Page 8
viii

First things first

Usage Notes

Do:
Turn off the product before cleaning.
Use a soft cloth moistened with mild detergent to clean the display
housing.
Disconnect the power plug from AC outlet if the product is not being used
for a long period of time.
Don't:
Block the slots and openings on the unit provided for ventilation.
Use abrasive cleaners, waxes or solvents to clean the unit.
Use under the following conditions:
In extremely hot, cold or humid environments.
In areas susceptible to excessive dust and dirt.
Near any appliance that generates a strong magnetic field.
Place In direct sunlight.

Precautions

Follow all warnings, precautions and maintenance as recommended in this user's guide to maximize the life of your unit.
Warning:
Do not look into the projector's lens when the lamp is on. The bright light may hurt
your eyes.
To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
Please do not open or disassemble the product as this may cause electric shock.
When changing the lamp, please allow unit to cool down, and follow all changing
instructions.
This product will detect the life of the lamp itself. Please be sure to change the lamp
when it shows warning messages.
Reset the "Lamp Hour Reset" function from the Onscreen display "Management"
menu after replacing the lamp module.
When switching the projector off, please ensure the projector completes its cooling
cycle before disconnecting power.
Turn on the projector first and then the signal sources.
Do not use lens cap when projector is in operation.
When the lamp reaches the end of its life, it will burn out and may make a loud
popping sound. If this happens, the projector will not turn back on until the lamp module has been replaced. To replace the lamp, follow the procedures listed under "Replacing the Lamp".
Page 9
Information for your safety and comfort iii
First things first viii
Usage Notes viii
Precautions viii
Introduction 1
Product Features 1
Package Overview 2
Projector Overview 3
Projector Outlook 3
Remote Control and Control Panel Layout 5
Getting Started 7
Connecting the Projector 7
Turning the Projector On/Off 8
Turning on the Projector 8
Turning the projector off 9
Adjusting the Projected Image 10
Adjusting the Height of Projected Image 10
How to optimize image size and distance 11
How to get a preferred image size by adjusting distance and zoom 13

Contents

User Controls 15
Installation menu 15
Acer Empowering Technology 16
Onscreen Display (OSD) Menus 17
Color 18
Image 20
Setting 22
Management 24
Audio 24
3D 25
Language 26
Appendices 27
Page 10
Troubleshooting 27
LED & Alarm Definition Listing 32
Replacing and cleaning the dust filters 33
Replacing the Lamp 34
Ceiling Mount Installation 35
Specifications 38
Compatibility modes 40
Regulations and safety notices 42
Page 11
1

Introduction

Product Features
This product is a single-chip DLP® projector. Outstanding features include:
DLP
X1161P/X1161PA/X1161PN/X112 series: Native 800 x 600 SVGA resolution
Acer ColorBoost technology delivers nature’s true colors for vivid, life-like
High brightness and contrast ratio
Versatile display modes (Bright, Presentation, Standard, Video, Game,
NTSC / PAL / SECAM compatible and HDTV (720p, 1080i, 1080p) supported
Lower power consumption and economy (ECO) mode extends lamp life
Acer EcoProjeciton Technology delivers Intelligent power management
Empowering Key reveals Acer Empowering Technology utilities (Acer
Advanced digital keystone correction optimizes presentations
Smart detection delivers quick, intelligent source detection
Multi-language onscreen display (OSD) menus
Manual focus projection lens zooms up to 1.1x
2x digital zoom and pan function
Microsoft
®
technology
X1261P/X1261PN series: Native 1024 x 768 XGA resolution 4:3 / 16:9 aspect ratio supported
images
Education, User) enable optimum performance in any situation
approach and physical efficiency improvement
eView, eTimer, ePower, e3D Management) for easy adjustment of settings
®
Windows® 2000, XP, Vista®, Windows 7, Macintosh® OS
compliant
English
Page 12
English
2
Package Overview
This projector comes with all the items shown below. Check to make sure your unit is complete. Contact your dealer immediately if any thing is missing.
Projector Power cord VGA cable
XXXXXX
3V
Battery Security card User’s guide
Remote control Quick start guide Carrying case
Dust filters
(Optional)
(Optional)
Page 13
3
Projector Overview
Projector Outlook
Front / upper side
8
3
9
2
1
# Description # Description
1 Zoom lens 6 Power button 2 Tilt adjusting wheel 7 Remote control 3 Remote control receivers 8 Ventilation (inlet) 4 Focus ring 9 Ventilation (outlet) 5 Zoom lever
Rear side
X261P
VGA IN S-VIDEO VIDEO RS232 VGA OUT AUDIO IN
6
7
5
4
3
8
35421
6
English
X1161PN/X1261PN
X1161P/X1161PA/X112
7
9
VGA IN
VGA IN S-VIDEO
8
VIDEO
Page 14
4
English
# Description # Description
1 PC analog signal/HDTV/component
video input connector 2 S-Video input connector 7 Power socket 3 Composite video input connector 4 RS232 connector 9 USB ctrl connector
Monitor loop-through output 5
connector (VGA-Out)
6 Audio input connector
8
Kensington
TM
lock port
Note: Connector interface is subject to model's specifications.
Page 15
5
Remote Control and Control Panel Layout
1
3
15
4
16
7
9
11
2
# Icon Function Description
1 Remote control
2 POWER Refer to the "Turning the Projector On/Off" section.
receiver
Receives signals from remote control.
2
14
5
6 8
10
12 13
English
3 MENU
Press "MENU" to launch the Onscreen display (OSD)
menu, back to the previous step for the OSD menu operation or exit the OSD menu.
Confirm your selection of items.
4 VGA Press "VGA" to change source to the VGA connector. This
5 VIDEO Press "VIDEO" to change source to composite video. (for
6 S-VIDEO Press "S-VIDEO" to change source to S-Video. (for X1161P/
7 ZOOM Zooms the projector display in or out.
8 SOURCE Changes the active source.
9 RESYNC Automatically synchronizes the projector to the input source.
10 ASPECT RATIO To choose the desired aspect ratio (Auto/4:3/16:9).
11
FREEZE To pause the screen image.
connector supports analog RGB, YPbPr (480p/576p/720p/ 1080i), YCbCr (480i/576i) and RGBsync.
X1161P/X1161PA/X112/X1261P series only)
X1161PA/X112/X1261P series only)
Page 16
English
6
# Icon Function Description
12 HIDE Momentarily turns off the video. Press "HIDE" to hide the
13 Empowering
14 KEYSTONE Adjusts the image to compensate for distortion caused by
15 Four directional
16 KeyPad 0~9 Press "0~9" to input a password in the "Security".
key
select keys
image, press again to display the image.
Unique Acer functions: eView, eTimer, ePower Management.
tilting the projector (± 40 degrees).
Use up, down, left, right buttons to select items or make adjustments to your selection.
Note:
Remote Control Placement
Please refer to the illustration to attach the remote control to the projector.
Page 17
7

Getting Started

Connecting the Projector
VGA
RS232
USB
D-Sub
3
D-Sub
VGA IN S-VIDEO VIDEO RS232 VGA OUT AUDIO IN
6
Video output
1
S-Video output
2
USB
English
D-Sub
3
4
Y
7
Y
D-Sub
5
8
W
R
# Description # Description
1 Power cord 5 Audio cable jack/jack
2 USB cable 6 S-Video cable
3 VGA cable 7 Composite video cable
4 RS232 cable 8 Audio cable jack/RCA
Note: To ensure the projector works well with your computer, please make sure the timing of the display mode is compatible with the projector. Note: Connector interface is subject to model's specifications. Note: USB cable needs powered extender if the length is over 5 m.
Page 18
8
Turning the Projector On/Off
English
Turning on the Projector
1 Ensure that the power cord and signal cable are securely connected. The
Power indicator LED will flash red.
2 Turn on the projector by pressing "Power" button on the control panel,
and the Power indicator LED will turn blue.
3 Turn on your source (computer, notebook, video player ,etc.). The
projector will detect your source automatically.
If the screen displays "Lock" and "Source" icons, it means the projector is locked onto a specific source type and there is no such type of input signal detected.
If the screen displays "No Signal", please make sure the signal cables are securely connected.
If you connect to multiple sources at the same time, use the "Source" button on the remote control to switch between inputs.
Power button
Page 19
9
Turning the projector off
1 To turn the projector off, press the power button. This message appears:
"Please press the power button again to complete the shutdown process." Press the power button again.
2 The LED power indicator will turn RED and blink rapidly after the projector
is turned off, and the fan(s) will continue to operate for about 2 minutes to ensure that the system cools properly. (only supported under "Instant Resume" mode)
3 As long as the power cord remains plugged in, you can press the power
button to turn the projector immediately back on anytime during the 2­minute shutdown process. (only supported under "Instant Resume" mode)
4 Once the system has finished cooling, the LED power indicator will stop
blinking and turn solid red to indicate standby mode.
5 It is now safe to unplug the power cord.
Warning indicators:
"Projector Overheated. Lamp will automatically turn off soon." This onscreen message indicates that the projector has overheated. The lamp with automatically turn off, the projector will automatically shut down, and the LED temp indicator will turn solid red. Contact your local dealer or service center.
"Fan failed. Lamp will automatically turn off soon." This onscreen message indicates that the fan has failed. The lamp will automatically turn off, the projector will automatically shut down, and the LED temp indicator will blink. Contact your local dealer or service center.
English
Note: Whenever the projector automatically shuts down and the LED lamp indicator turns solid red, contact your local reseller or service center.
Page 20
10
Adjusting the Projected Image
English
Adjusting the Height of Projected Image
The projector is equipped with elevator feet for adjusting the height of image.
To raise/lower the image:
Use Tilt adjusting wheel to fine-tune the display angle.
Tilt adjusting wheel
Page 21
11
46"
How to optimize image size and distance
Consult the table below to find the optimal image sizes achievable when the projector is positioned at a desired distance from the screen. Example: If the projector is 2.0 m from the screen, good image quality is possible for image sizes between 46" and 50".
Note: Remind as below figure, the space of 88 cm height is required when located at 2.0 m distance.
M
a
x
s
c
r
e
e
n
s
i
z
e
M
i
n
s
c
r
e
e
n
s
i
z
e
A
2.0 m Desired Distance
B
46"
50"
Height: 80 cm
C
Height: 88 cm from base to top of image
English
Figure: Fixed distance with different zoom and screen size.
Page 22
12
English
Screen size
Desired
Distance
(m)
Diagonal
<A>
Zoom Ratio: 1.1x
(inch)
<B>
1 23 47 x 35 40 25 51 x 38 44
2 46 93 x 70 80 50 103 x 77 88
2.5 57 116 x 87 100 63 128 x 96 111
3 69 140 x 105 120 76 154 x 115 133
3.5 80 163 x 122 140 88 179 x 135 155
4 92 186 x 140 160 101 205 x 154 177
4.5 103 209 x 157 181 114 231 x 173 199
5 114 233 x 174 201 126 256 x 192 221
6 137 279 x 209 241 151 308 x 231 265
7 160 326 x 244 281 177 359 x 269 310
8 183 372 x 279 321 202 410 x 308 354
9 206 419 x 314 361 227 462 x 346 398
10 229 465 x 349 401 252 513 x 385 442
(Min zoom) (Max zoom)
W (cm) x H (cm)
Top
From base
to top of
image (cm)
<C>
Diagonal
(inch)
<B>
Screen size
W (cm) x H (cm)
Top
From base to top of image
(cm)
<C>
Page 23
13
How to get a preferred image size by adjusting distance and zoom
A
50"
Desired image size
D
Height
from base to top of image
2.0 m
2.2 m
C
The table below shows how to achieve a desired image size by adjusting either the position or the zoom ring. For example: to obtain an image size of 50" set the projector at a distance 2.0 m and 2.2 m from the screen and adjust the zoom level accordingly.
B
Desired Distance
English
Page 24
14
English
Desired Image Size Distance (m) Top (cm)
Diagonal (inch)
<A>
30 61 x 46 1.2 1.3 53
40 81 x 61 1.6 1.7 70
50 102 x 76 2.0 2.2 88
60 122 x 91 2.4 2.6 105
70 142 x 107 2.8 3.1 123
80 163 x 122 3.2 3.5 140
90 183 x 137 3.6 3.9 158
100 203 x 152 4.0 4.4 175
120 244 x 183 4.8 5.2 210
150 305 x 229 5.9 6.6 263
180 366 x 274 7.1 7.9 315
200 406 x 305 7.9 8.7 351
250 508 x 381 9.9 10.9 438
300 610 x 457 11.9 526
Zoom Ratio: 1.1x
W (cm) x H (cm)
Max zoom
<B>
Min zoom
<C>
From base to top of
image
<D>
Page 25
15

User Controls

Installation menu
The installation menu provides an onscreen display (OSD) for projector installation and maintenance. Use the OSD only when the message "No signal input" is displayed on the screen.
The menu options include settings and adjustments for screen size and distance, focus, keystone correction and more .
1 Turn on the projector by pressing "Power" button on the control pad.
2 Press the menu button on the control pad to launch the OSD for projector
installation and maintenance.
English
3 The background pattern acts as a guide to adjusting the calibration and
alignment settings, such as screen size and distance, focus and more .
Use the up and down arrow keys to select an option, the left and right arrow keys to adjust selected option settings, and the right arrow key to enter a submenu for feature setting. The new settings will be saved automatically upon exiting the menu.
4 Push the menu button anytime to exit the menu and return to the Acer
welcome screen.
Page 26
English
16
Acer Empowering Technology
Acer Empowering Key provide four Acer unique functions, they are "Acer eView Management", "Acer eTimer Management", "Acer ePower Management" and "Acer e3D Management respectively.
Press " " key to launch the Onscreen display main menu to modify its function.
When the Empowering Menu is displayed, use the " " key to select the main menu.
Acer eView Management
Acer eTimer Management
Acer ePower Management
Acer e3D Management
"Acer eView Management" is for display mode selection. Please refer to Onscreen Display Menus section for more detail.
"Acer eTimer Management" provides the reminding function for presentation time control. Please refer to Onscreen Display Menus section for more detail.
"Acer ePower Management" provides user one shortcut to save the projector life. Please refer to Onscreen Display section for more detail.
"Acer e3D Management" provides the 3D functions. Please refer to Onscreen Display Menus section for more detail.
Page 27
17
Onscreen Display (OSD) Menus
The projector has multilingual OSD that allow you to make image adjustments and change a variety of settings.
Using the OSD menus
To open the OSD menu, press "MENU" on the remote control or control
panel.
When the OSD is displayed, use the keys to select any item in the
main menu. After selecting the desired main menu item, press to enter submenu for feature setting.
Use the keys to select the desired item and adjust the settings by
using the keys.
Select the next item to be adjusted in the submenu and adjust as described
above.
Press "MENU" on the remote control or control panel, the screen will
return to the main menu.
To exit OSD, press "MENU" on the remote control or control panel again.
The OSD menu will close and the projector will automatically save the new settings.
English
Main menu
Setting
Sub menu
Page 28
English
18
Color
Display Mode
Wall color
Brightness
Contrast
Saturation
Tint
There are many factory presets optimized for various types of images.
Bright: For brightness optimization.
Presentation: For meeting presentation.
Standard: For common environment.
Video: For playing video in a bright environment.
Game: For game content.
Education: For education environment.
User: Memorize user's settings.
Use this function to choose a proper color according to the wall. There are several choices, including white, light yellow, light blue, pink, dark green. It will compensate the color deviation due to the wall color to show the correct image tone.
Adjust the brightness of the image.
Press to darken the image.
Press to lighten the image.
"Contrast" controls the difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image.
Press to decrease the contrast.
Press to increase the contrast.
Adjusts a video image from black and white to fully saturated color.
Press to decrease the amount of color in the image.
Press to increase the amount of color in the image.
Adjusts the color balance of red and green.
Press to increase the amount of green in the image.
Press to increase the amount of red in the image.
Page 29
19
Color Temperature
Gamma
Mode Use this function to choose CT1, CT2 (Native), CT3, User mode.
R Gain Adjusts the red gain for color temperature optimization.
G Gain Adjusts the green gain for color temperature optimization.
B Gain Adjusts the blue gain for color temperature optimization.
Effects the representation of dark scenery. With greater gamma value, dark scenery looks brighter.
Note: "Saturation" and "Tint" functions are not supported under computer or HDMI mode.
English
Page 30
English
20
Image
Projection (for X1161PA/X112/X1161PN/X1261PN series only)
Front-Desktop: The factory default setting.
Rear-Desktop: When you select this function, the projector
reverses the image so you can project from behind a translucent screen.
Rear-Ceiling: When you select this function, the projector reverses
and inverts the image at same time. You can project from behind a translucent screen with ceiling mounted projection.
Front-Ceiling: When you select this function, the projector inverts
the image for ceiling-mounted projection.
Keystone Adjust image distortion caused by tilting projection. (±40 degrees)(for
Projection mode (for X1161P/X1261P series only)
X1161PA/X112/X1161PN/X1261PN series only)
Front: The factory default setting.
Rear: Reverses the image so you can project from behind a
translucent screen.
Projection Location
(for X1161P/X1261P series only)
Auto: Automatically adjusts projection location of image.
Desktop
Ceiling: Turns the image upside down for ceiling-mounted
projection.
Auto Keystone Automatically adjusts vertical image. (for X1161P/X1261P series only)
Page 31
21
Maunal Keystone Adjust image distortion caused by tilting projection. (±40 degrees) (for
Aspect Ratio
X1161P/X1261P series only)
<Note> The Manual Keystone function is unavailable under Auto Keystone setting to "On".
(for X1161P/X1261P series only) Use this function to choose your desired aspect ratio.
Auto: Keep the image with original width-higth ratio and maxi
mize the image to fit native horizontal or vertical pixels.
4:3: The image will be scaled to fit the screen and displayed using
a 4:3 ratio.
16:9: The image will be scaled to fit the width of the screen and
the height adjusted to display the image using a 16:9 ratio.
Sharpeness Adjusts the sharpness of the image.
Press to decrease the sharpness.
Press to increase the sharpness.
H. Position (Horizontal position)
V. Position (Vertical position)
Press to move the image left.
Press to move the image right.
Press to move the image down.
Press to move the image up.
Frequency "Frequency" changes the projector's refresh rate to match the
Tracking Synchronizes the signal timing of the projector with the graphics card.
frequency of your computer’s graphics card. If you can see a vertical flickering bar in the projected image, use this function to make the necessary adjustments.
If you experience an unstable or flickering image, use this function to correct it.
English
Note: "H. Position", "V. Position", "Frequency" and "Tracking" functions are not supported under HDMI or Video mode.
Page 32
English
22
Setting
Closed Caption
Security Security
Selects a preferred closed captioning mode from CC1, CC2, CC3, CC4, (CC1 displays captions in the primary language in your area). Select "Off" to turn off the captioning feature. This function is only available when a composite video or S-Video input signal is selected and its system format is NTSC. <Note> Set your screen aspect ratio to 4:3. This function is not available when the aspect ratio is "16:9" or "Auto" .
This projector provides a useful security function for the administrator to manage usage of the projector .
Press to change the "Security" setting. If the security function is enabled, your must enter the "Administrator Password" first
before changing the security settings.
Select "On" to enable the security function. The user has to
If "Off" is selected, then the user can turn on the projector
Timeout(Min.) Once "Security" is activated to "On", the administrator can set
timeout function.
Press or to select the timeout interval.
The range is from 10 minute to 990 minutes.
When the time is up, the projector will prompt the user to
The factory default setting of "Timeout(Min.)" is "Off".
Once the security function is enabled, the projector will
enter a password to operate the projector. Please refer to the "User Password" section for details.
without password.
enter the password again.
request user to enter password when switch on the projector . Both "User Password" and "Administrator Password" can be accepted for this dialogue.
Page 33
23
User password
Press to setup or change the "User Password".
Press number keys to set your password on the remote control
and press "MENU" to confirm.
Press to delete character.
Enter the password when you see "Confirm Password"
displayed.
The password should be between 4 and 8 characters long.
If you select "Request password only when plugging the
power cord in.", the projector will prompt the user to enter the password every time the power cord is plugged.
If you select "Always request the password when turning the
projector on.", the user has to enter the password every time when the projector is turned on.
Administrator Password The "Administrator Password" can be used in both the "Enter
Administrator Password" and "Enter Password" dialog boxes.
Press to change the "Administrator Password".
The factory default of "Administrator Password" is "1234".
If you forgot your administrator password, do the following to retrieve the administrator password:
An unique 6-digit "Universal Password" which is printed on
the Security Card (please check accessory in the box). This unique password is the number which will be accepted by projector anytime no matter what the Administrator Password is.
If losing this security card and number, please contact with an
Acer service center.
VGA OUT (Standby) Default is "Off". Choose "On" to enable VGA OUT connection. (for
Reset
X1261P only)
Press the button and choose "Yes" to return the
parameters on all menus to the factory default settings.
English
Page 34
English
24
Management
ECO Mode Choose "On" to dim the projector lamp which will lower power
High Altitude Choose "On" to turn on High Altitude mode. Operate the fans at
Turn Off Mode
consumption, extend the lamp life and reduce noise. Choose "Off" to return normal mode.
full speed continuously to allow for proper high altitude cooling of the projector.
Instant Off: Shuts down the projector without fan cooling.
Instant Resume: Resumes the system when the Power button
is pressed again within 2 minutes.
Auto Shutdown The projector will automatically shutdown when there is no signal
Lamp Hour Elapse Displays the lamp’s elapsed operating time (in hours).
Lamp Reminding Activate this function to display a reminder to change the lamp 30
Lamp Hour Reset
input after the allocated time. (default is 120 minutes)
hours before its expected end-of-life.
Press the button and choose "Yes" to turn the lamp hour counter to 0 hours.
Audio
Volume (for X1261P series only)
Press to decrease the volume.
Press to increase the volume.
Mute (for X1261P series only)
Choose "On" to mute the volume.
Choose "Off" to restore the volume.
Page 35
25
3D
3D Choose "On" to enable DLP 3D function.
On: Choose this item while using DLP 3D glasses, 120Hz 3D
capable graphics cards and HQFS format file or DVD with corresponding SW player.
Off: Turn off 3D mode.
3D Format
3D L/R Invert If you see a discrete or overlapping image while wearing DLP 3D
3D Warning Message Choose "On" to display the 3D warning message.
Adjust the 3D format to display 3D content correctly.
glasses, you may need to execute "Invert" to get best match of left/right image sequence to get the correct image (for DLP 3D).
English
Note: It needs correct settings on graphic card 3D application program for correct 3D display. Note: The SW players, such as Stereoscopic Player and DDD TriDef Media Player can support 3D format files. You can download these three players on web page below,
- Stereoscopic Player (Trial): http://www.3dtv.at/Downloads/Index_en.aspx
- DDD TriDef Media Player (Trial): http://www.tridef.com/download/TriDef-3-D-Experience-4.0.2.html
Note: "3D L/R Invert" is only available when 3D is enabled. Note: There has reminder screen if 3D still enable when power on projector. Please adjust setting depended on your purpose.
Page 36
English
26
Language
Language
Choose the multilingual OSD menu. Use the or key
to select your preferred menu language.
Press to confirm the selection.
Page 37
27

Appendices

Troubleshooting
If you experience a problem with your Acer projector, refer to the following troubleshooting guide. If the problem persists, please contact your local reseller or service center.
Image Problems and Solutions
# Problem Solution
1 No image appears
onscreen
2 Partial, scrolling
or incorrectly displayed image (for PC (Windows 2000/XP/Vista/ Windows 7))
Connected as described in the "Getting Started"
section.
Ensure none of the connector pins are bent or
broken.
Check if the projector lamp has been securely
installed. Please refer to the "Replacing the Lamp" section.
Make sure you have removed the lens cap and the
projector is switched on.
Press "RESYNC" on the remote control or control panel.
For an incorrectly displayed image:
Open "My Computer," open the "Control
Panel," and then double-click the "Display" icon.
Select the "Settings" tab.
Verify that your display resolution setting is
lower than or equal to WUXGA-RB (1920 x
1200).
Click the "Advanced Properties" button.
If the problem still appears, change the monitor display you are using and follow the steps below:
Verify that the resolution setting is lower than
or equal to WUXGA-RB (1920 x 1200).
Click the "Change" button under the
"Monitor" tab.
Click "Show all devices". Next, select "Standard
monitor types" under the SP box, and choose the resolution mode you need under the "Models" box.
Verify that the resolution setting of the
monitor display is lower than or equal to WUXGA-RB (1920 x 1200).
English
Page 38
28
English
3 Partial, scrolling
or incorrectly displayed image (For notebooks)
4 The screen of the
notebook computer is not displaying your presentation
5 Image is unstable
or flickering
6 Image has vertical
flickering bar
Press "RESYNC" on the remote control or control
panel.
For an incorrectly displayed image:
Follow the steps for item 2 (above) to adjust
the resolution of your computer.
Press the toggle output settings. Example:
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8], Gateway [Fn]+[F4], IBM [Fn]+[F7], HP [Fn]+[F4], NEC [Fn]+[F3], Toshiba [Fn]+[F5]
If you experience difficulty changing resolutions or
your monitor freezes, restart all equipment including the projector.
If you are using a Microsoft
notebook: Some notebook PCs may deactivate their own screens when a second display device is in use. Each has a different way to be reactivated. Refer to your computer's manual for detailed information.
If you are using an Apple
notebook: In System Preferences, open Display and select Video Mirroring "On".
®
Windows® based
®
Mac® OS based
Adjust the "Tracking" to correct it. Refer to the
"Image" section for more information.
Change the display color depth settings on your
computer.
Use "Frequency" to make an adjustment. Refer to
the "Image" section for more information.
Check and reconfigure the display mode of your
graphics card to make it compatible with the projector.
7 Image is out of
focus
8 Image is stretched
when displaying a "widescreen" DVD title
Make sure the lens cap is removed.
Adjusts the focus ring on the projector lens.
Make sure the projection screen is within the
required distance of 3.9 to 39.0 feet (1.2 to 11.9 meters) from the projector. Refer to the "How to Get a Preferred Image Size by Adjusting Distance and Zoom" section for more information.
When you play a DVD encoded in anamorphic or 16:9 aspect ratio you may need to adjust the following settings:
If you play a 4:3 format DVD title, please change the
format to 4:3 in the projector OSD.
If the image is still stretched, you will also need to
adjust the aspect ratio. Set up the display format to 16:9 (wide) aspect ratio on your DVD player.
Page 39
29
9 Image is too small
or too large
10 Image has slanted
sides
11 Image is reversed
Adjust the zoom lever on the top of the projector.
Move the projector closer to or further from the
screen.
Press "MENU" on the remote control. Go to "Image -
-> Aspect Ratio" and try different settings or press"Aspect Ratio" on the remote control to adjust directly.
If possible, reposition the projector so that it is
centered on the screen.
Press the "Keystone / " button on the remote
control until the sides are vertical.
Press "MENU" on the remote control. Go to "Image -
-> Auto Keystone" and choose "Off" on the OSD, if "Keystone" button is not available on the remote control.
Select "Image --> Projection" on the OSD and adjust
the projection direction.
English
Page 40
30
OSD Messages
English
# Condition Message Reminder
1 Message Fan Fail - the system fan is not working.
Projector Overheated - the projector has exceeded its recommended operating temperature and must be allowed to cool down before it may be used.
Replace the lamp - the lamp is about to reach its maximum lifetime. Prepare to replace it soon.
Page 41
31
Problems with the Projector
# Condition Solution
1 The projector stops responding
to all controls
2 Lamp burns out or makes a
popping sound
If possible, turn off the projector, then unplug the power cord and wait at least 30 seconds before reconnecting power.
When the lamp reaches the end of its useful life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section.
English
Page 42
32
LED & Alarm Definition Listing
English
LED Messages
Message
Input Power Plug Flash ON to OFF 100ms --
Standby V --
Power button ON -- V
Lamp retry -- Quick Flashing
Power off (Cooling state) Quick Flashing --
Power button OFF: Cooling completed; Standby Mode
Error (Thermal Failure) Quick Flashing RED and Steady BLUE by returns
Error (Fan lock) Quick Flashing RED and Steady BLUE by returns
Error (Lamp breakdown) Quick Flashing BLUE and Steady RED by returns
Error (Color Wheel fail) Quick Flashing BLUE and Steady RED by returns
Red Blue
V--
Power LED
Page 43
33
Replacing and cleaning the dust filters
Replacing the dust filters 1 Turn the projector off then unplug the power cord.
2 Pull the both sides dust filters out. (Illustration #1) 3 Clean or replace the dust filter. 4 To put the dust filters back, reverse the previous step.
(Illustration #1)
Cleaning the dust filters
Clean the dust filters after every 1000 hours of use. If they are not cleaned periodically, they can become clogged with dust, preventing proper ventilation. This can cause overheating and damage the projector. (Normally 1000 hours is recommended, clean period will be depending on actual environment)
Please find following steps for cleaning procdure: 1 To clean the dust filters, use a small vacuum cleaner designed for
computers and other office equipments. It also can be cleaned by water. (Illustration #2)
2 If the dirt is difficult to remove or the filter is broken, please contact your
local dealer or service center to obtain a new filter.
English
Dust Filter
(Illustration #2)
Page 44
English
34
Replacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the lamp.
The projector will detect the lamp life. You will be shown a warning message "Lamp is approaching the end of its useful life in full power operation. Replacement Suggested!" When you see this message, change the lamp as soon as possible. Make sure the projector has been cooling down for at least 30 minutes before changing the lamp.
Warning: The lamp compartment is hot! Allow it to cool down before changing the lamp.
1
3
2
4
To Change the Lamp 1 Turn off the projector by pressing the Power button. 2 Allow the projector at least 30 mins to cool down. 3 Disconnect the power cord. 4 Use a screwdriver to remove the screws from the cover. (Illustration #1) 5 Push up and remove the cover. 6 Remove the two screws that secure the lamp module (Illustration #2) and
pull up the lamp bar.(Illustration #3)
7 Pull out the lamp module by force. (Illustration #4)
To replace the lamp module, reverse the previous step.
Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped.
Page 45
35
Ceiling Mount Installation
If you wish to install the projector using a ceiling mount, please refer to the steps below:
1 Drill four holes into a solid, structurally sound part of the ceiling, and
secure the mount base.
13
mm
20
mm
49.9
mm
mm
8.4
Note: Screws are not included. Please obtain the appropriate screws for your type of ceiling.
2 Secure the ceiling rod using the appropriate type of four-cylinder screws.
Ceiling Mount Base
Short Rod
- Attach to ceiling
English
130 mm
Screw Type A
50 mm length / 8 mm diameter -
Long Rod
Extension Rod
Long Cylinder Cap Allen Key
- For tightening/loosening
Tightening Screw
Medium Rod
Page 46
English
36
3 Use the appropriate number of screws for the projector size to attach the
projector to the ceiling mount bracket.
Screw Type B
Smaller Washer
Large Washer
upports projector and allows
Projector Bracket
for adjustments
-
Note: It is recommended that you keep a reasonable space between the bracket and the projector to allow for proper heat distribution. Use two washers for extra support, if deemed necessary.
4 Attach the ceiling bracket to the ceiling rod.
Screw Type A
50 mm length/ 8 mm diameter
-
Spacer
- For heat dissipation
Large cylinder cap
Allen Key
- For tightening/loosening
Tightening Screw
Page 47
37
5 Adjust the angle and positioning as necessary.
Tightening Screw
Allen Key
Allen Key
Tightening Screw
Note: The appropriate type of screw and washer for each model is listed in the table below. 3 mm diameter screws are enclosed in
the screw pack.
Models Screw Type B Washer Type
X1161P/X1161PA/ X1161PN/X112/ X1261P/X1261PN
Diameter (mm) Length (mm) Large Small
325VV
English
SCREW SPEC. M3 x 25 mm
95.00 mm
82.30 mm
15.00 mm
Page 48
English
38
Specifications
The specifications listed below are subject to change without notice. For final specs, please refer to Acer's published marketing specifications.
Projection system
Resolution X1161P/X1161PA/X1161PN/X112: Native: SVGA (800 x
Computer compatibility IBM PC and compatibles, Apple Macintosh, iMac and
Video compatibility NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/
Aspect ratio 4:3 (native), 16:9
Displayable colors 16.7 million colors
Projection lens F/ 2.41 - 2.55, f = 21.79 mm - 23.99 mm, 1.1X manual
Projection screen size (diagonal) 27" (70 cm) - 300" (762 cm)
Projection distance 3.9' (1.2 m) - 39.0' (11.9 m)
Throw ratio 50"@2m (1.95 - 2.15:1)
Horizontal scan rate 30k - 100 kHz
Vertical refresh scan rate 50-120 Hz
Lamp type 190W user-replaceable lamp
Keystone correction
Audio Internal speaker with 2 W output (X1261P)
Weight 2.2Kg (4.85 Ibs)
Dimensions (W x D x H) 268 mm x 192 mm x 80 mm (10.6" x 7.6" x 3.1")
Digital Zoom 2X
Power supply AC input 100 - 240 V auto-switching power supply
Power consumption Normal mode: 235W ± 10% @ 110VAC
Operating temperature 0ºC to 40ºC / 32ºF to 104ºF
®
DLP
600) , Maximum: UXGA (1600 x 1200), WSXGA+ (1680x1050), 1080p(1920x1080), WUXGA-RB (1920 x
1200) X1261P/X1261PN: Native: XGA (1024 x 768),
Maximum: UXGA (1600 x 1200), WSXGA+ (1680x1050), 1080p(1920x1080), WUXGA-RB (1920 x
1200)
VESA standards: SXGA, XGA, VGA, SVGA, SXGA+, WXGA, WXGA+, WSXGA +
K/K1/L), HDTV (720p, 1080i, 1080p), EDTV (480p, 576p), SDTV (480i, 576i)
zoom lens
±40 degrees
ECO mode: 197W ± 10% @ 110VAC Standby mode < 0.5W
Page 49
39
Standard package contents
AC power cord x1
VGA cable x1
Remote control x1
Battery x1 (for remote control)
User's guide (CD-ROM) x1
Quick start guide x1
Security card x1
Carrying case x1 (Optional)
I/O connectors X1261P X1161PN/X1261PN X1161P/X1161PA/X112
Power socket V V V
USB (for remote computer control)
VGA IN V V V
S-Video V X V
Composite video V X V
RS232 V X X
VGA output V X X
3.5 mm audio jack input
XV V
VX X
* Design and specifications are subject to change without notice.
English
Page 50
40
Compatibility modes
English
VGA Analog
1 VGA Analog - PC Signal
Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
VGA 640x480 60 31.47
640x480 72 37.86 640x480 75 37.50 640x480 85 43.27 640x480 119.51 61.60
SVGA 800x600 56 35.20
800x600 60 37.88 800x600 72 48.08 800x600 75 46.88 800x600 85 53.67 800x600 119.85 77.20
XGA 1024x768 60 48.36
1024x768 70 56.48 1024x768 75 60.02 1024x768 85 68.67 1024x768 119.804 98.80
SXGA 1152x864 70 63.80
1152x864 75 67.50
1152x864 85 77.10 1280X1024 60 63.98 1280X1024 72 77.90 1280X1024 75 79.98 1280X1024 85 91.15
QuadVGA 1280x960 60 60.00
1280x960 75 75.00
SXGA+ 1400x1050 60 65.32
UXGA 1600x1200 60 75.00
PowerBook G4 640x480 60 31.50
640x480 66.6(67) 35.00
800x600 60 37.88 1024x768 60 48.36 1152x870 75 68.68 1280x960 75 75.20
i Mac DV (G3) 1024x768 75 60.30
Page 51
41
2 VGA Analog - Extended Wide timing
Modes Resolution V.Frequency [Hz] H.Frequency [KHz] WXGA 1280x768 60 47.78
1280x768 75 60.29 1280x768 85 68.63 1280x720 60 44.80 1280x800 60 49.60 1440x900 60 55.90
1680x1050 60 65.30
1366x768 60 47.71
1920x1080-RB 60 66.60
UWXGA 1920x1200-RB 60 (59.95) 74.04
3 VGA Analog -Component Signal
Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
480i 720x480 59.94 (29.97) 15.70
480p 720x480 59.94 31.47
576i 720x576 50(25) 15.60 576p 720x576 50 31.25 720p 1280x720 60 45.00 720p 1280x720 50 37.50
1080i 1920x1080 60(30) 33.75
1080i 1920x1080 50(25) 28.10 1080p 1920x1080 60 67.50 1080p 1920x1080 50 56.25 1080p 1920x1080 24 27.00 1080p 1920x1080 23.97 26.97
Horizontal scan rate:
Vertical scan rate:
Max. pixel rate:
30-100 kHz
50-120 Hz
165 MHz
English
Page 52
42

Regulations and safety notices

English
FCC notice
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver.
Connect the device into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this equipment. Operation with non-certified peripherals is likely to result in interference to radio and TV reception.
Caution
Changes or modifications not expressly approved by the manufacturer could void the user's authority, which is granted by the Federal Communications Commission, to operate this device.
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Page 53
43
Remarque à l'intention des utilisateurs canadiens
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du Canada.
Declaration of Conformity for EU countries
Acer hereby declares that this projector series is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Compliant with Russian regulatory certification
Radio device regulatory notice
Note: The regulatory information below is for models with wireless LAN and/or Bluetooth only.
General
This product complies with the radio frequency and safety standards of any country or region in which it has been approved for wireless use. Depending on configurations, this product may or may not contain wireless radio devices (such as wireless LAN and/or Bluetooth modules).
English
English
Canada — Low-power license-exempt radio communication devices (RSS-210)
a Common information
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.
b Operation in 2.4 GHz band
To prevent radio interference to the licensed service, this device is intended to be operated indoors and installation outdoors is subject to licensing.
List of applicable countries
This device must be used in strict accordance with the regulations and constraints in the country of use. For further information, please contact the local office in the country of use. Please see http://ec.europa.eu/enterprise/rtte/implem.htm
for the latest country list.
Page 54
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi,
New Taipei City 221, Taiwan
 
'HFODUDWLRQRI&RQIRUPLW\
:H
$FHU,QFRUSRUDWHG
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan Contact Person: Mr. RU Jan, e-mail:ru_jan@acer.com.tw
And,
$FHU,WDO\VUO
Via Lepetit, 40, 20020 Lainate (MI) Italy Tel: +39-02-939-921, Fax: +39-02 9399-2913, www.acer.it
Hereby declare that:
3URGXFW 3URMHFWRU 7UDGH1DPH $FHU 0RGHO1XPEHU '69'69'1;'1; 0DFKLQH7\SH ;3;3$;31;
Is compliant with the essential requirements and other relevant provisions of the following EC
directives, and that all the necessary steps have been taken and are in force to assure that
production units of the same product will continue comply with the requirements.
(0&'LUHFWLYH(&DVDWWHVWHGE\FRQIRUPLW\ZLWKWKHIROORZLQJ
KDUPRQL]HGVWDQGDUGV
-. EN55022, AS/NZS CISPR22, Class B
-. EN55024
-. EN61000-3-2 Class A
-. EN61000-3-3
/RZ9ROWDJH'LUHFWLYH(&DVDWWHVWHGE\FRQIRUPLW\ZLWKWKHIROORZLQJ
KDUPRQL]HGVWDQGDUG
-. EN60950-1
5R+6'LUHFWLYH(&RQWKH5HVWULFWLRQRIWKH8VHRIFHUWDLQ+D]DUGRXV
6XEVWDQFHVLQ(OHFWULFDODQG(OHFWURQLF(TXLSPHQW
-. The maximum concentration values of the restricted substances by weight in homogenous material are:
Lead 0.1% Polybrominated Biphenyls (PBB’s) 0.1%
Mercury 0.1% Polybrominated Diphenyl Ethers (PBDE’s) 0.1%
Hexavalent Chromium 0.1% Cadmium 0.01%
!
;31VHULHV
'LUHFWLYH(&ZLWKUHJDUGWRHVWDEOLVKLQJDIUDPHZRUNIRUWKHVHWWLQJ
RIHFRGHVLJQUHTXLUHPHQWVIRUHQHUJ\UHODWHGSURGXFW
;3
Page 55
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi,
New Taipei City 221, Taiwan
7KHVWDQGDUGVOLVWHGEHORZDUHDSSOLHGWRWKHSURGXFWLIEXLOWZLWK:/$1 PRGXOHRUZLUHOHVVNH\ERDUGDQGPRXVH
577('LUHFWLYH(&DV DWWHVWHGE\FRQIRUPLW\ZLWKWKHIROORZLQJ KDUPRQL]HGVWDQGDUG
z$UWLFOHD+HDOWKDQG6DIHW\
-. EN60950-1
-. EN62311
z$UWLFOHE(0&
-. EN301 489-1
-. EN301 489-17
z$UWLFOH6SHFWUXP8VDJHV
-. EN300 328
-. EN301 893 (Applicable to 5GHz high performance RLAN).
<HDUWREHJLQDIIL[LQJ&(PDUNLQJ
_______________________________
1RY
-
RU Jan/Sr. Manager Date Regulation Center, Acer Inc.
Page 56
Acer America Corporation
333 West San Carlos St.,
Suite 1500
San Jose, CA 95110
U. S. A.
7HO   254-298- 4000
)D[   254-298-41 47
ZZZ DF HUFRP
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The following local Manufacturer / Importer is responsible for this declaration:
Product: DLP Projector
Model Number: DSV0008/DSV1144/DNX0009/DNX1143
Machine Type: X1161P/X1161PA/X1161PN/X112/X1261P/
Name of Responsible Party: Acer America Corporation
Address of Responsible Party: 333 West San Carlos St.
Contact Person: Acer Representative
Phone No.: 254-298-4000
Fax No.: 254-298-4147
X1261PN series
Suite 1500
San Jose, CA 95110
U. S. A.
Loading...