ACCO Brands Paper Shredder User Manual

Operating Instructions

1. Connect shredder to mains supply

2. Press the central power button. This will switch the power
on and all the LED warning symbols on the indicator
panel will flash in sequence. The shredder will now be in
standby mode and the “power on” symbol on the
indicator panel will be illuminated amber.

3. To commence shredding, press the right hand auto feed
button, this will illuminate the feed area green and
illuminate the face symbol green. This sets the shredder
into auto mode and initiates the Mercury anti jam
mechanism. You are now able to shred.

4. Insert paper to be shredded into the feed area. The
Mercury anti jam mechanism will sense the thickness of
the paper being shredded. If the paper thickness is within
the shredders capacity the motor will start and your
documents will be shredded. Cutters will stop once the
shredding process is complete. If the paper thickness is
greater than the shredders sheet capacity the area round
the feed slot will turn from green to red and the motor
will not run. In this situation the Mercury icon on the
indicator panel will flash red, the green face symbol will
go off, instead the red face symbol will be illuminated.

5. If this happens, remove some of the sheets from the
paper stack and re-try until the feed area reverts back to
green, the shredder will then automatically start and
allow the paper to be shredded. If the shredder is left in
auto mode for more than 10 minutes without being
used, the shredder will automatically turn back to
standby mode in order to save power

Shredder Waste Sacks

The Mercury Departmental shredders (50 and 70 litre
models) take the Rexel AS1000 shredder bag (product
code 40070).

Oiling your shredder

Occasionally you will need to oil the cutters on models
RDS2050, RDS2270, RDX1750 and RDX1970 only. Rexel
Mercury Deskside shredders should not need oiling.
Please purchase Rexel lubricant spray (40106) for this.
Please note this is special shredder oil. Do not use any
other type of oil.

CD and Credit Card Shredding

Pull up the orange CD guide located in the centre of the
feed area and flip it into position over the shredder
mouth.

For credit card shredding, switch the shredder to auto
mode and insert the card into the centre slot.

For CD shredding, extend the sides of the orange CD
guide, switch the shredder to auto mode and place the
CD into the centre of the CD slot.

Only 1 CD can be shred at a time.

Over Heating

If the shredder is used continuously for long periods of
time the shredder may overheat. If this occurs the egg
timer symbol on the indicator panel will flash amber, the
green face will go off and you will see the red face
symbol. When the shredder is ready to be used again the
egg timer symbol will stop flashing and the green face
will show once again. To resume shredding press the auto
button.

Safety First

Shredders are safe to use as long as you take a few safety
precautions.

• Ensure the machine is plugged into an easily accessible

power outlet, and ensure the cable is not likely to trip up
a passer by.

• Any attempt to repair this unit by unqualified personnel

will invalidate the warranty. Please return to supplier

• Unplug your shredder before moving it or when it is not

in use for an extended period of time

• Do not operate with a damaged power sully cord or

plug, after it malfunctions, or after it has been damaged
in any manner

• Do not overload electrical outlets beyond capacity as this

can result in fire or electrical shock

• The socket-outlet should be installed near the equipment

and shall be easily accessible

• Do not alter the attachment plug. The plug is configured

for the appropriate electrical supply

• Do not use near water

• Do not use aerosol dusters or cleaners

• Do not spray anything into the shredder

Although this shredder has been designed to be child safe, it is
not advised to operate the machine near children.