ABB System pro M Technical data

Technical data
Mounting and operating instructions
System
Pro M
14
Mounting
Universal mounting position using snap-on mounting to standard 35x7.5mm DIN rail.
Miniature circuit breakers (MCBs) can also be mount ed to front of door using a panel cut-out with breaker handle pro trud ing through panel opening for external operation. Special front mount ing kit type ME is avail able (see page 2.12).
Mounting MCB
Removing MCB
Possible mounting arrangements of MCB accessories
H11
NT
S/H
S
MCB
Connection
Terminals are suitable for solid or fl exible conductors from 18 to 4 AWG (0.75 to 25mm2) with no busbar connected. When max i mum busbar size of 36 mm2 is used, maximum cable is 6 AWG (16 mm2).
Maximum tightening torque of 17.5 in-lb (2 Nm) for line/load terminals and 4.5 in-lb (0.5Nm) for ac ces so ry device terminals.
H11
A
MCB
S/H
S
BM
BM
Operation
MCBs are switched on by moving the handle to the upper po si tion. Stamped onto the handle switch, a “I” is visible confi rming that the breaker is closed.
The MCBs are “trip-free,” if the handle is being forced to the “ON” position, the breaker will still trip under fault conditions.
The “O” marking indicates that the breaker is in the “OFF” position. The MCB is now open and the load is disconnected from line power.
When a breaker has tripped, the MCB handle should rst be set to the full “OFF” position to make certain the trip mechanism has been reset. Once the fault has been determined and cleared the MCB can again be switched “ON”.
Maintenance
ABB miniature circuit breakers require no special maintenance; only normal electrical system maintenance pro ce dures are required.
A
MCB
BM
Auxiliary switch/bell alarm
neutral disconnect
Shunt trip or undervoltage release
mounted with auxiliary switch
Shunt trip and/or undervoltage release
Auxiliary switch
Set MCB to “OFF” position and mount Set breaker to “ON” position Break out opening on side of MCB auxiliary switch to side of breaker Attach with spring clamps
Bell alarm with auxiliary contact
Set MCB to “OFF” position, insert metal pin as Break out opening on side of MCB noted above with arrow and mount device to Set breaker to “ON” position and remove seal side of MCB Attach with spring clamps
Shunt trip and undervoltage release
14
Remove seal Add shunt trip to MCB Attach with spring clamps
Low Voltage Products & Systems 14.21
ABB Inc. • 888-385-1221 • www.abb-control.com AC 1000 - 11/03
System
Pro M
14
Technical data
Busbars & connectors Connection methods
Dual function terminals provided in open position for connection to busbars. Pressing on screw head opens box terminal for cable insertion. Only the lower terminal is dual func tion.
Lower terminals can be bussed together with single phase or multi-phase busbars as shown. Upper ter mi nals can also be busbar con nect ed.
14
Terminals allow for con nec tion of cable 18-4 AWG. Conductors of different sizes may also be used in same terminal.
Lower terminal can also be bussed with solid round con duc tor.
Up to fi ve conductors, 16 AWG each, can be safely connected per terminal.
Cables can be connected to box terminals in addition to busbar con nec tions on lower, dual function terminals.
14.22 Low Voltage Products & Systems
AC 1000 - 11/03 ABB Inc. • 888-385-1221 • www.abb-control.com
Technical data
S260, S270, & S280
System
Pro M
14
Item S260-B S260-C, -D S270-K S280-K
Approvals: UL 1077 1077 1077 1077 CSA C22.2 — No.235 C22.2 — No. 235 C22.2 — No. 235 — VDE 0641, 0660 0660 0660 0660 IEC 898, 947 898, 947 898, 947 898, 947
No. of poles: 1,2,3,4 1+N,3+N 1,2,3 1,2,3,4, 1+N,3+N 1,2,3,4,1+N,3+N Tripping characteristic: B C,D K K Rated currents: 6 to 63A 0.5 to 63A 0.5 to 63A 0.2 to 63A Minimum operating voltage: 12V 12V 12V 12V UL/CSA rated voltage & Single pole
interrupting capacity
120VAC 10kA 10kA 10kA
6kA for 50-63A 240VAC 6kA 10kA 6kA 10kA 6kA 10kA
6kA for 50-63A 6kA for 40-63A 277VAC 6kA 6kA 6kA
277/480 VAC 6kA 6kA 6kA 10kA
60VDC 10kA 10kA 10kA 10kA 10kA 10kA — 125VDC 10kA 10kA 10kA
Frequency: 50/60Hz (See below) 50/60Hz (see below) 50/60Hz (see below) 50/60Hz (see below) Rated voltage
IEC single pole 240/415VAC 240/415VAC 240/415VAC 240/415VAC 60VDC 60VDC 60VDC 60VDC IEC multi-pole 415VAC 415VAC 415VAC 415VAC 110VDC 110VDC 110VDC 110VDC
Protection category: IP20 IP20 IP20 IP20 Depth of unit per DIN 43880: 68 Mounting position: optional optional optional optional Standard mounting: 35 Main and shunt trip terminals:
Wire size 6-40A 18-4 AWG 0.5-40A 18-4 A WG 0.5-40A 18-4 AWG 0.2-40A 18-4 AWG 50A & above 18-2 AWG 50A & above 18-2 AWG 50A & above 18-2 AWG 50A & above 18-2 AWG Torque 17.5 in-lbs. 17.5 in-lbs. 17.5 in-lbs. 17.5 in-lbs. Tool #2 Posidrive #2 Posidrive #2 Posidrive #2 Posidrive
Accessory terminals Wire size 18-16 AWG 18-16 AWG 18-16 AWG 18-16 AWG Torque 4.5 in-lbs. 4.5 in-lbs. 4.5 in-lbs. 4.5 in-lbs. Tool #1 Posidrive #1 Posidrive #1 Posidrive #1 Posidrive
Service life at rated load: In < 32 A, 20,000 operations In < 32 A, 20,000 operations In < 32 A, 20,000 operations In < 32 A, 20,000 operations In > 32 A, 10,000 operations In > 32 A, 10,000 operations In > 32 A, 10,000 operations In > 32 A, 10,000 operations
Ambient temperatures: -25°C to +55°C -25°C to +55°C -25°C to +55°C -25°C to +55°C Storage temperatures -40°C to + 70°C -40°C to + 70°C -40°C to + 70°C -40°C to + 70°C
Shock resistance: 30g minimum of 2 impacts, 30g minimum of 2 impacts, 30g minimum of 2 impacts, 30g minimum of 2 impacts, shock duration of 13ms shock duration of 13ms shock duration of 13ms shock duration of 13ms
Vibration resistance: 5g, 20 cycles, 5 Hz, 150 Hz 5g, 20 cycles, 5 Hz, 150 Hz 5g, 20 cycles, 5 Hz, 150 Hz 5g, 20 cycles, 5 Hz, 150 Hz @ 0.8 ~ In @ 0.8 ~ I
Disconnecting neutral rating: 6kA switching 6kA switching 6kA switching
Multi pole Single pole Multi pole Single pole Multi pole Single pole Multi pole
10kA for 0.2-40A
10kA for 0.2-40A 10kA for 0.2-32A
10kA for 0.2-40A
mm 68mm 68mm 68mm
mm DIN rail 35mm DIN rail 35mm DIN rail 35mm DIN rail
n
@ 0.8 ~ I
n
@ 0.8 ~ I
n
14
Infl uence of frequency on electro-magnetic trips
Magnetic trip values shown on trip curves are valid for 50/60Hz ap pli ca tions. For frequencies other than 50/60Hz, the mag net ic (in stan ta neous) trip values are increased by the factor given below:
16 Approx. factor 1 1.1 1.2 1.5 1.5
Thermal tripping is independent of frequency.
1 Available for purchase. See page 14.19.
Low Voltage Products & Systems 14.23
ABB Inc. • 888-385-1221 • www.abb-control.com AC 1000 - 11/03
2/3 - 60Hz 100Hz 200Hz 400Hz DC
Loading...
+ 4 hidden pages