3M Accessories Selection Guide

Image Product No. Description

723

Accessory Belt Clip to be used with the 3M

™

Wrist Strap Monitor 725

724P

Power Supply for 3M

™

Wrist Strap Workstation Monitor 724 and 3M

™

Static Monitor 790

724VK

Monitor Verification Kit. Verifies the resistance range of the Workstation Monitor 724

725VK

Monitor Verification Kit. Verifies the resistance range of the Wrist Strap Monitor 725

732

Replacement Remote Input Jack. 6 ft. (1.8 m) long cord.

To be used with Workstation Monitor 724.

733

Remote Splitter Kit. 6 ft. (1.8 m) long cord. To be used with Workstation Monitor 724.

740P

Power Supply for 3M

™

Wrist Strap and Footwear Tester 740

746P

Power Supply for 3M

™

Wrist Strap Tester 746

790VK

Verification Kit. One 5 ft. (1.5 m) Dual Conductor Cord 2360, one test wrist band socket

assembly, and one two-wire male connector with 24 in. (0.61 m) lead wire.

2380

Monitor/Table Mat Replacement Cord, 6 ft. (1.8 m), with 10 mm snap. Extends from

the 3M

™

Wrist Strap Workstation Monitor 724 to the static control worksurface to be

monitored. This cord does not have a resistor molded into the snap fastener cap.

2389

Monitor/Table Mat Interconnect Cord, 10 ft. (3 m), with 10 mm snap. A straight cord

with male snap fasteners at each end and no resistors. Used to interconnect two

monitored worksurfaces.

Image Product No. Description

3033

Snap Fastener, male, 0.125 in. (3.2 mm) hole, 10 mm diameter. For mats and runners. 1800/8800 Series.

3034

Snap Fastener, female, 0.125 in. (3.2 mm) hole, 10 mm diameter. For 3M

™

Mats and Runners

1800/8800 series.

3037

Insulated Bulldog Clip. Fits standard banana plug.

3038

Uninsulated Alligator Clip. Fits standard banana plug.

3040

Ground Cord, 15 ft. (4.6 m), with 10 mm snap. Molded-in male snap fastener with integral

1 megohm resistor on one end, solderless terminal on other. Connects all 3M

™

Static Control Mats

and Runners to building ground.

3041

Grounding Kit for 3M

™

Static Protective Hard Laminate includes #10 screw, lock washer, #10 nut,

lock washer wing nut, #10 self-tapping screw and one 10 ft. (3.0 m) ground cord. Ground cord has

a 1 megohm resistor.

3042

Wrist Strap Grounding System. Grounds two single conductor wrist straps and conveniently

mounts beneath the edge of most work benches. Comes complete with 10 ft. (3.0 m) ground cord.

3043

Interconnect Cord 5 ft. (3.5 m), with 10 mm snap. Molded-in male snap fastener at each end.

Connects all static control mats and runners to each other. Ground cord has a 1 megohm resistor.

CTA242

This remote terminal connects to WS Aware workstation monitors and provides connection for

dual wire wrist straps for an operator and a visitor. Patented plug-in replaceable board with the

jacks reduces cost of ownership of the monitor since only one inexpensive board needs to be

replaced when the jacks are worn out, instead of the entire terminal.

CTA243

Before sensitive devices are handled, Big Brother alarms alert the operator to plug-in. Once Big Brother

senses that the operator is properly grounded the alarm is silenced. The Big Brother wrist strap terminal

makes the WS Aware one of the most intelligent and cost-effective systems on the market today.

CTA245

Replacement board with jacks for WS Aware remote monitors CTA242 and CTA243.

FGC150M

FGC151M

The low profile beveled cap prevents the cord from being accidentally removed from the mat.

A 3/8 in. (10 mm) stud securely snaps to the mat, and at the other end of the 15 ft. (4.5 m) cord

is a ring terminal.

WSGR2

This metal grounding block accommodates two wrist straps and comes complete with mounting

hardware. Designed to be mounted under the bench and keep the wrist strap connections safe.

The integral 15 ft. (4.5 m) cord ends with a ring terminal. Two 4 mm parking studs hold coiled

cords to reduce damage to cords left at the bench. No resistor.

3M

™

Accessories Selection Guide 3M

™

Accessories Selection Guide

No Photo

Available