7800S Series Fullface Respirator Facepieces 05/22/14
__________________________________________________________________________________________
Page 1 of 5
Article Information Sheet
Copyright,2014,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
This Article Information Sheet is provided as a courtesy in response to a customer request. A Safety Data Sheet (SDS) has not
been prepared for these product(s) because they are articles. Articles are not subject to the Occupational Safety and Health
Administration’s Hazard Communication Standard (29 CFR 1910.1200(b)(6)(v)). As defined in this standard: “Article”
means a manufactured item other than a fluid or particle: (i) which is formed to a specific shape or design during
manufacture; (ii) which has end use function(s) dependent in whole or in part upon its shape or design during end use; and
(iii) which under normal conditions of use does not release more than very small quantities, e.g., minute or trace amounts of a
hazardous chemical, and does not pose a physical or health risk to employees.
Document Group:
19-5452-8
Version Number:
1.00
Issue Date:
05/22/14
Supercedes Date:
Initial Issue
SECTION 1: Identification
1.1. Product identifier
7800S Series Fullface Respirator Facepieces
Product Identification Numbers
70-0707-1025-9, 70-0707-1026-7, 70-0707-1027-5
1.2. Recommended use and restrictions on use
Recommended use
Respiratory Protection
1.3. Supplier’s details
MANUFACTURER:
3M
DIVISION:
Personal Safety Division
ADDRESS:
3M Center, St. Paul, MN 55144-1000, USA
Telephone:
1-888-3M HELPS (1-888-364-3577)
1.4. Emergency telephone number
1-800-364-3577 or (651) 737-6501 (24 hours)
SECTION 2: Hazard identification
This product is exempt from hazard classification according to OSHA Hazard Comunication Standard, 29 CFR 1910.1200.
SECTION 3: Composition/information on ingredients
Ingredient C.A.S. No. % by Wt
SILICONE RUBBER None 45 - 65 Trade Secret *
7800S Series Fullface Respirator Facepieces 05/22/14
__________________________________________________________________________________________
Page 2 of 5
POLYCARBONATE LENS None 10 - 30 Trade Secret *
ABS None 10 - 20 Trade Secret *
POLYPROPYLENE None 5 - 15 Trade Secret *
ZINC COATED STEEL None 0.5 - 1.5 Trade Secret *
NATURAL RUBBER None 0 - 1 Trade Secret *
*The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade
secret.
SECTION 4: First aid measures
4.1. Description of first aid measures
Inhalation:
No need for first aid is anticipated.
Skin Contact:
No need for first aid is anticipated.
Eye Contact:
No need for first aid is anticipated.
If Swallowed:
No need for first aid is anticipated.
SECTION 5: Fire-fighting measures
In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
Not applicable.
6.2. Environmental precautions
Not applicable.
6.3. Methods and material for containment and cleaning up
Not applicable.
SECTION 7: Handling and storage
7.1. Precautions for safe handling
This product is considered to be an article which does not release or otherwise result in exposure to a hazardous chemical
under normal use conditions.
7.2. Conditions for safe storage including any incompatibilities
No special storage requirements.
SECTION 8: Exposure controls/personal protection
This product is considered to be an article which does not release or otherwise result in exposure to a hazardous chemical
under normal use conditions. No engineering controls or personal protective equipment (PPE) are necessary.
7800S Series Fullface Respirator Facepieces 05/22/14
__________________________________________________________________________________________
Page 3 of 5
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
General Physical Form:
Solid
Odor, Color, Grade:
Solid, odorless, black injection molded respirator facepiece with
attached clear injection molded lens/shield.
Odor threshold
Not Applicable
pH
Not Applicable
Melting point
No Data Available
Boiling Point
Not Applicable
Flash Point
Not Applicable
Evaporation rate
Not Applicable
Flammability (solid, gas)
Not Classified
Flammable Limits(LEL)
Not Applicable
Flammable Limits(UEL)
Not Applicable
Vapor Pressure
Not Applicable
Vapor Density
Not Applicable
Specific Gravity
Not Applicable
Solubility In Water
Not Applicable
Solubility- non-water
Not Applicable
Partition coefficient: n-octanol/ water
No Data Available
Autoignition temperature
Not Applicable
Decomposition temperature
Not Applicable
Viscosity
Not Applicable
Volatile Organic Compounds
Not Applicable
Percent volatile
Not Applicable
VOC Less H2O & Exempt Solvents
Not Applicable
SECTION 10: Stability and reactivity
This material is considered to be non reactive under normal use conditions.
SECTION 11: Toxicological information
Inhalation:
No health effects are expected
Skin Contact:
No health effects are expected
Eye Contact:
No health effects are expected
Ingestion:
No health effects are expected
7800S Series Fullface Respirator Facepieces 05/22/14
__________________________________________________________________________________________
Page 4 of 5
Additional Information:
This product, when used under reasonable conditions and in accordance with the directions for use, should not present a
health hazard. However, use or processing of the product in a manner not in accordance with the product's directions for use
may affect the performance of the product and may present potential health and safety hazards.
SECTION 12: Ecological information
This article is expected to present a low environmental risk either because use and disposal are unlikely to result in a
significant release of components to the environment or because those components that may be released are expected to have
insignificant environmental impact.
SECTION 13: Disposal considerations
Dispose of contents/container in accordance with the local/regional/national/international regulations.
SECTION 14: Transport Information
For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501.
SECTION 15: Regulatory information
Chemical Inventories
This product is an article as defined by TSCA regulations, and is exempt from TSCA Inventory requirements.
SECTION 16: Other information
NFPA Hazard Classification
Health: 1 Flammability: 1 Instability: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address
the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar
emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include
the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.
Document Group:
19-5452-8
Version Number:
1.00
Issue Date:
05/22/14
Supercedes Date:
Initial Issue
DISCLAIMER: The information in this Article Information Sheet (AIS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF
PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a
particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and
application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user
evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or
application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer
may have resulted in errors, omissions or alterations in this information,3M makes no representations as to its completeness
or accuracy. In addition, information obtained from a database may not be as current as the information in the AIS available
directly from 3M.
7800S Series Fullface Respirator Facepieces 05/22/14
__________________________________________________________________________________________
Page 5 of 5
3M USA AISs are available at www.3M.com
Loading...