Page 1
3M
™
Shrunk Delta Ribbon (SDR) Cable Assembly
.80 mm High Speed Digital Data Transmission, 26 position 1MF26-L5XX-00C-XXX
• Supports new AIA Industrial Camera Link®
Standard for new Mini C/L camera to C/L
frame grabber applications
• 11 shielded, twisted twinax pairs with four
drain wires
• Double overall shield with inner foil and
outer braid
• Rugged ribbon contact type
• Rugged thumbscrew retention
• R/A overmolded MDR backshells eliminate
bend radius issues
• See Regulatory Information Appendix
(RIA) for chemical compliance information
TS-2122-C
Date Modified: December 17, 2007
Sheet 1 of 4
Physical
Connector Contact Plating:
Electrical
Voltage Rating:
Insulation Resistance:
Withstanding Voltage:
Environmental
Temperature Rating:
Wiping Area:
Underplating:
Shell Options:
Color:
Material:
Cable:
Color:
Jacket Material:
Flammability:
Marking:
Current Rating:
30 μ″ [ 0.76 μm ] Min Gold
100 μ″ [ 2.55 μm ] Nickel
Parchment / Beige & Black
Overmolded option: Polyvinyl Chloride (PVC)
& Acrylonitrile Butadiene Styrene (ABS)
Parchment / Beige
Polyvinyl Chloride (PVC)
AWM VW-1
3M logo
30 V
0.5 A
1 × 108 Ω min at 100 V
125 VAC
0°C to +70°C
for 1 minute
RMS
DC
UL File No.: E86982
3M
Interconnect Solutions
http://www.3M.com/interconnects/
Camera Link is a certification mark of Automated Imaging Association.
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
Page 2
3M
™
Shrunk Delta Ribbon (SDR) Cable Assembly
.80 mm High Speed Digital Data Transmission, 26 position 1MF26-L5XX-00C-XXX
Length
Figure 1
R/A SDR to Straight MDR Cable Assembly
.99
25.2
12345678910111213
14 15 16 17 18 19 2 021 22 23 24 25 26
Figure 2
R/A SDR Connector
( -76 Option)
.72
18.2
.37
9.4
Figure 4
SDR R/A Overmolded Connector
1415 16 17 1819 20 2122 23 24 25 26
12345678910111213
Figure 3
R/A SDR Connector
( -77 Option)
1.48
37.5
123456789
14 15 16 17 18 19 20 21 22 23 24 25 26
10 11 12 13
Figure 5
MDR Straight Connector
.51
13.0
Note: 1. For length dimension, refer to the product ordering number.
3M
Interconnect Solutions
http://www.3M.com/interconnects/
TS-2122-C
Sheet 2 of 4
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
Page 3
3M
™
Shrunk Delta Ribbon (SDR) Cable Assembly
.80 mm High Speed Digital Data Transmission, 26 position 1MF26-L5XX-00C-XXX
Length
Figure 6
R/A MDR To Straight SDR Cable Assembly
1.56
39.7
.77
19.4
3
6
1
2
2
5
1
2
1
4
1
2
0
3
1
2
2
9
2
1
8
2
0
7
2
9
6
1
8
5
1
7
4
1
6
3
1
5
2
1
4
1
1
Figure 7
R/A MDR Connector
( -86 Option )
.5 5
14.0
14 15 16 17 18 19 20 21 22 23 24 25 26
123456789
10 11 12 13
Figure 8
R/A MDR Connector
( -87 Option )
.96
24.4
.35
9.0
12345678 910111213
14 15 16 17 18 19 20 21 22 23 24 25 26
.47
12.0
Figure 9
MDR R/A Connector
Note: 1. For length dimension, refer to the product ordering number.
3M
Interconnect Solutions
http://www.3M.com/interconnects/
Figure 10
SDR Straight Connector
TS-2122-C
Sheet 3 of 4
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
Page 4
3M
™
Shrunk Delta Ribbon (SDR) Cable Assembly
.80 mm High Speed Digital Data Transmission, 26 position 1MF26-L5XX-00C-XXX
CN-1
Conn.
Pos.
2 XO- YO- YO- XO- 25
15 XO+ YO+ YO+ XO+ 12
3 X1- Y1- Y1- X1- 24
16 X1+ Y1+ Y1+ X1+ 11
4 X2- Y2- Y2- X2- 23
17 X2+ Y2+ Y2+ X2+ 10
5 XC- Yclk- Yclk- XC- 22
18 XC+ Yclk+ Yclk+ XC+ 9
6 X3- Y3- Y3- X3- 21
19 X3+ Y3+ Y3+ X3+ 8
7 Ser TC+ 100 ohm 100 ohm Ser TC+ 20
20 Ser TC- Terminat ed Term i nat ed Ser TC- 7
8 Ser TFG- ZO- ZO- Ser TFG- 19
21 Ser TFG+ ZO+ ZO+ Ser TFG+ 6
9 CC1- Z1- Z1- CC1- 18
22 CC1+ Z1+ Z1+ CC1+ 5
10 CC2+ Z2- Z2- CC2+ 17
23 CC2- Z2+ Z2+ CC2- 4
11 CC3- Zclk- Zclk- CC3- 16
24 CC3+ Zclk+ Zclk+ CC3+ 3
12 CC4+ Z3- Z3- CC4+ 15
25 CC4- Z3+ Z3+ CC4- 2
INNER
1
14
13
26
Shell Shell
SHIELD
INNER
SHIELD
INNER
SHIELD
INNER
SHIELD
INNER
SHIELD
INNER
SHIELD
INNER
SHIELD
INNER
SHIELD
Base Configurat i on
Full / Medium configuration
Cable
TWI N AX 1
TWI N AX 2
TWI N AX 3
TWI N AX 4
TWI N AX 5
TWI N AX 6
TWI N AX 7
TWI N AX 8
TWI N AX 9
TWI N AX 10
TWI N AX 11
INNER
SHIELD
INNER
DRAIN WIRE
BRAID SHIELD
SHIELD
INNER
SHIELD
INNER
SHIELD
CN-2
Conn.
Pos.
INNER
SHIELD 1
INNER
SHIELD 14
INNER
SHIELD 13
INNER
SHIELD 26
Cable Assembly Wiring Diagram
Ordering Information
1MF26-L5XX-00C-XXX
76 = Straight discrete MDR backshell to a R/A (cable dresses down) overmolded SDR.
77 = Straight discrete MDR backshell to a R/A (cable dresses up) overmolded SDR.
86 = R/A (cable dresses down) overmolded MDR to a straight overmolded SDR.
87 = R/A (cable dresses up) overmolded MDR to a straight overmolded SDR.
Notes:
1. For a cable length of less than 2m, the length tolerance is +50mm / -0mm
2. For a cable length of 2m or more, the length tolerance is +3% / -0% of cable length
3M
Interconnect Solutions
http://www.3M.com/interconnects/
Table 1
(RIA E1 & C1 apply)
Length =:
100 = 1m
200 = 2m
500 = 5m
A00 = 10m
Refer to length dimension in figures 1 & 3
Reference notes 1 & 2 for cable length tolerance
TS-2122-C
Sheet 4 of 4
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
Page 5
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/717/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
RIA-2217B-c
Page 6
Appendix E5: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under
Item 6 of the Annex to the Directive.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means
that the product or part does not contain any of the following substances in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
RIA-2217B-c
Page 7
Appendix C3: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
the legal theory asserted.
3
3M Electronics
Interconnect Products
6801 River Place Blvd.
Austin, T X 78726-9000
U.S.A.
1-800-225-5373
www.3m.com/interconnects 3M is a trademark of 3M Company.
Please recycle. Printed in USA.
© 3M 2007. All rights reserved.
RIA-2217B-c
Loading...