3M 1HF10V User Manual
3M™ High
Flow Series
Polypropylene Filter Cartridges
3M™ High Flow Series
Filtration Systems
Features such as an ergonomically designed handle and a unique “twist-to-lock” seating
mechanism facilitate easy operation and maintenance of the filter system. The system is
particularly suit able for many OEM applications.
Materials Of Construction
Each grade of the 3M™ High Flow Series Filter is manufactured from meltblown FDA
compliant polypropylene microber media, providing high particle reduction efciency
with broad chemical compatibility.
No adhesives, binders, surfactants, or lubricants are used in the manufacturing process.
Operating Conditions
The 10” 3M High Flow series filter system is
ideally suited for applications where convenience
and ease of use are priorities. The system uses 3M
Innovation and 3M Purification Inc.'s extensive
filtration experience to enable flow rates up to 85
gpm in a single cartridge. The Compound Radial
Pleat design packs significantly higher usable
surface areas per unit volume than can be achieved
with conventional pleated cartridge filters.
Features & Benefits
High flow capability of up to 85
gpm per cartridge
Patent Pending Compound
Radial Pleat design
Compact design
• Reduced filter usage - minimizes product loss,
labor, disposal costs, operator exposure, and
downtime for filter change-out
• High loading capacity for long life and
lower cost filtration
• Smaller housing minimizes capital expense requirements
• Reduces system footprint
Maximum Operating Temperature
Maximum Forward Differential Pressure
Recommended Change-out Pressure
4.0
3.5
3.0
2.5
2.0
1.5
Dierential Pressure (psid)
1.0
0.5
0
0
160°F ( 71°C)
50 psid @ 68°F (3.4 bar @ 20°C)
35 psid @ 68°F (2.4 bar @ 20°C)
Typical Housing and Cartridge Flow Rates
10 and above Micron
20
40
60
1 Micron
Housing Only
2 Micron
5 Micron
80
100
Absolute rating
Easy to Use
FDA compliant
• Reproducible effluent quality throughout the filter’s life
• No special tools or hardware required for filter change-out
minimizes downtime
• “Twist-to-lock” seating mechanism provides positive seal.
• Ergonomically designed handle - facilitates easy cartridge
installation and removal
• Suitable for wide range of food and beverage applications
10” 3M™ High Flow Series Housing
The 10” 3M™ High Flow Series Filter Housing is specifically designed
to deliver all of the system’s benefits in a compact footprint. The
housing is designed, manufactured, tested, and code stamped in
accordance with ASME Section VIII, Division 1. Vessel construction
is 304 stainless steel with a glass-bead finish.
Housing Specification
3M™ High Flow Series Filter Housing Dimensions
Dimensions are for over all space requirements only. For all other uses, request a
certified drawing.
Head space required
for cartridge removal
Model
Outside Diameter
Number of Filter Elements
Material
Connection size (inches)
Drain Size Inches (NPT)
Vent or Gauge Size Inches (NPT)
Approximate Housing Weight (lbs. / kgs)
1HF10V
8 5/8
1 - 10" Element
304 Stainless Steel
2
1/2
1/4
150 lbs
(63.5 cm)
42in
(107 cm)
17 ½ in. max
12 ½ in. min
(44.5 cm max.
31.8 cm min.)
3M™ High Flow Series ASME Code Filter Housing Ordering Guide
Filter
Elements
Model
HF1 10 - 10 in V - Vertical B - 304 SS
Size
Configuration
Housing Material
Gasket Material
GA - Silicone
GB - Fluorocarbon
27in
13 in.
(33 cm)
GC - EPR
GD - Nitrile
3M™ High Flow Series - 10" Filter Cartridge Ordering Guide
Filter Designation
HF - High Flow
Element Length
(inches)
10 - 10 in PP - Polypropylene
Material
Absolute Removal
Rating (Microns)
001 - 1µm
002 - 2µm
005 - 5µm
010 - 10µm
015 - 15µm
025 - 25µm
040 - 40µm
070 - 70µm
O-Ring
A - Silicone
B - Fluorocarbon
C - EPR
D - Nitrile
Packaging Options
(per box)
01 - 1 pack
Loading...