|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Lighting Systems LSB-10 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
1BHF PG |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
-ZUFTQSFBEÜ -4# 1BSBCPMJD -PVWFS -JHIU 5 1FS 'PPU /PNJOBM 4FDUJPO |
|||||||
8 1/2" (216 mm)
1 3/4" (37.5 mm) |
|
|
2 5/8" (66.7 mm) |
3 |
|
1 |
2 |
|
|
|
4 |
|
3 1/4" (82.6 mm) |
|
Half Scale |
Ordering Information |
|
|
Family |
|
Lamps |
|
Length |
|
Shielding |
|
Ballast |
Voltage |
|
Finish |
||||
|
LSB |
|
2 |
|
|
|
|
C |
|
|
|
|
|
|
|
|
|
|
|
2 = 2-Lamp T5 |
4 |
= 4-Foot |
|
C = Parabolic Louver |
28 |
= 28W T5 |
1 = 120 volt |
|
AL = Aluminum |
||||
|
|
|
|
|
8 |
= 8-Foot |
|
|
|
54 |
= 54W T5 |
2 = 277 volt |
|
WH = White |
||
|
|
|
|
|
|
|
|
|
|
5E |
= 54W T5 Emergency Pack |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2E |
= 28W T5 Emergency Pack |
|
|
|
|
|
Complete ordering instructions below. |
|
|
|
|
|
5D |
= 54W T5 Dimming |
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Features
1.Housing: Extruded aluminum. Die-cast end cap mechanically attached with no exposed fasteners or hardware.
2.Lamping: Two T5, 28 or 54 watt (as specified) fluorescent lamps per 4-foot nominal section. Provided by others.
3.Reflector: Precision die-formed semi-specular aluminum.
4.Louver: Parabolic louver, low-iridescent semi-specular anodized aluminum, 41° shielding lengthwise, blades are 1-1/3” (3.39cm) high and 2” (5.08cm) O.C. Louver frame is extruded aluminum and finished to match housing.
Electrical
Ballast is <10% THD, .98 ballast factor, pre-heat start. 18 gauge wire. Colorcoded quick connectors allow ease of connection for joiner modules. Power feed is 18 gauge white SJT. For special circuiting consult factory. Factory installed ballast disconnect allows the ballast to be disconnected from and reconnected to incoming power under load without turning the entire circuit off.
Dimming: 120/277 VAC 1% dimming level, 4 wire feed required.
Emergency Battery Pack: 28 watt: 520 lumens @ 90 minutes, 54 watt: 700 lumens @ 90 minutes, 4 wire feed required.
Mountings
Cable suspension (not shown) - 4-1/2" (11.43cm) diameter canopy finished white enamel, 1/16" (0.16cm) diameter stainless steel aircraft cable adjustable up to 36" (91.44cm). Dual-screw draw-tight connector to create hairline seam between joiner modules.
Finish
Powder coated baked white or aluminum finish. Custom colors available, consult factory.
Options and Accessories
Emergency Circuiting; special circuiting; X, T & L joiner blocks - consult factory.
Labels
UL, cUL and I.B.E.W.
Ordering Instructions
Individual Fixtures:
1.Order number of MODULES required.
2.Order one POWER FEED END SET per MODULE.
Continuous Rows:
1.Determine run length.
2.Order the appropriate number of MODULES for the complete run.
3.Order one POWER FEED END SET per run.
4.Order one CABLE ASSEMBLY per MODULE minus one per run.
5.For runs that exceed amperage limits, order the appropriate number of CABLE/CORD ASSEMBLIES.
Job Information |
Type: |
Job Name:
Cat. No.:
Lamp(s):
Notes:
"JSQPSU 3PBE 'BMM 3JWFS ." t t 'BY
We reserve the right to change details of design, materials and finish.
XXX MJHIUPMJFS DPN ½ 1IJMJQT (SPVQ t #
Loading...