MANUAL DE INSTRUCCIONES
MANUAL DE INSTRUÇÕES
INSTRUCTION MANUAL
2 3 4
1
5 6
7
HT420-HT500
* Advertencia: Léase este instructivo antes de usar el producto!
4 |
8 |
9 |
A |
C1 |
7
B |
C2 |
2
Intended use
Your Black & Decker hedgetrimmer has been designed for trimming hedges, shrubs and brambles. This tool is intended for consumer use only.
Safety instructions
Warning! When using mains-powered tools, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock, personal injury and material damage.
Read all of this manual carefully before operating the tool.
Retain this manual for future reference.
Remove the plug from the socket before carrying out any adjustment, servicing or maintenance.
Keep work area clean
Cluttered areas and benches can cause accidents.
Consider work area environment
Do not expose the tool to rain. Do not use the tool in damp or wet conditions. Keep the work area well lit. Do not use the tool where there is a risk of causing fire or explosion, e.g. in the presence of flammable liquids and gases.
Keep children away
Do not allow children, visitors or animals to come near the work area or to touch the tool or mains cable.
Dress properly
Do not wear loose clothing or jewellery, as these can be caught in moving parts. Preferably wear rubber gloves and non-slip footwear when working outdoors. Wear protective hair covering to keep long hair out of the way.
Personal protection
Always use safety glasses. Use a face or dust mask whenever the operations may produce dust or flying particles.
Hearing protection should be worn.
Guard against electric shock
Prevent body contact with earthed or grounded surfaces
(e.g. pipes, radiators, cookers and refrigerators). Electric safety can be further improved by using a high-sensitivity
(30 mA / 30 mS) residual current device (RCD).
Do not overreach
Keep proper footing and balance at all times.
Stay alert
Watch what you are doing. Use common sense. Do not operate the tool when you are tired.
Secure workpiece
Use clamps or a vice to hold the workpiece. It is safer and it frees both hands to operate the tool.
Connect dust extraction equipment
If devices are provided for the connection of dust extraction and collection facilities, ensure that these are connected and properly used.
ENGLISH
Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches are removed from the tool before operating the tool.
Extension cables
Before use, inspect the extension cable and replace if damaged. When using the tool outdoors, only use extension cables intended for outdoor use. Up to 30 m of Black & Decker extension cable can be used without loss of power.
Use appropriate tool
The intended use is described in this instruction manual. Do not force small tools or attachments to do the job of a
heavy-duty tool. The tool will do the job better and safer at the rate for which it was intended. Do not force the tool. Do not use the tool for purposes not intended, for example, do not use a circular saw to cut tree limbs or logs.
Warning! The use of any accessory or attachment or performance of any operation with this tool other than those recommended in this instruction manual may present a risk of personal injury.
Check for damaged parts
Before use, carefully check the tool and mains cable for damage. Check for misalignment and seizure of moving parts, breakage of parts, damage to guards and switches and any other conditions that may affect its operation. Ensure that the tool will operate properly and perform its intended function. Do not use the tool if any part is damaged or defective. Do not use the tool if the switch does not turn it on and off. Have any damaged or defective parts repaired or replaced by an authorised repair agent. Never attempt any repairs yourself.
Unplug the tool
Unplug the tool when it is not in use, before changing any parts of the tool, accessories or attachments and before servicing.
Avoid unintentional starting
Do not carry the tool with a finger on the on/off switch. Be sure that the tool is switched off when plugging in.
Do not abuse cord
Never carry the tool by its cord or pull it to disconnect from the socket. Keep the cord away from heat, oil and sharp edges.
Store idle tools
When not in use, tools should be stored in a dry, locked up or high place, out of reach of children.
Maintain tools with care
Keep cutting tools sharp and clean for better and safer performance. Follow the instructions for maintenance and changing accessories. Keep handles and switches dry, clean and free from oil and grease.
Repairs
This tool complies with relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts; otherwise this may result in considerable danger to the user.
3
ENGLISH
Electrical safety
This tool is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate.
Additional safety instructions for hedgetrimmers
Wear safety glasses or goggles when operating this tool.
Wear gloves when operating this tool.
Wear ear protection when operating this tool.
Immediately disconnect the cable from the mains if it is damaged or cut.
If the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1.Trigger switch
2.Front handle switch
3.Front handle
4.Guard
5.Blade
6.Blade sheath
7.Cable restraint
This hedgetrimmer has the following features for your benefit:
Ergonomically formed handles for comfortable cutting.
Machined blades for improved cutting.
Dual action blades for reduced vibration.
Do not expose the tool to rain or high humidity.
Keep the cable away from the blades while using this tool.
If you have not used a hedgetrimmer before, preferably seek practical instruction by an experienced user in addition to studying this manual.
Never touch the blades while the tool is running.
Never attempt to force the blades to come to a standstill.
Do not put the tool down until the blades have come to a complete standstill.
Regularly check the blades for damage and wear. Do not use the tool when the blades are worn or damaged.
Take care to avoid hard objects (e.g. metal wire, railings) when trimming. Should you accidentally hit any such object, immediately switch the tool off, unplug it and check for any damage.
Should the tool start to vibrate abnormally, immediately switch it off and check for any damage.
If the tool stalls, immediately switch it off. Unplug the tool before attempting to remove any obstructions.
After use, place the blade sheath supplied over the blades. Store the tool, making sure that the blade is not exposed.
Always ensure that all handles and guards are fitted when using the tool. Never attempt to use an incomplete tool or a tool with unauthorised modifications.
Never allow children to use the tool.
Be aware of falling debris when cutting the higher sides of a hedge.
This appliance is not intended for use by young or infirm persons without supervision. Children must be supervised to ensure they do not play with the appliance.
Assembly
Warning! Before assembly, make sure that the tool is switched off and unplugged and that the blade sheath is fitted over the blades.
Fitting the guard (fig. A)
Locate the guard (4) into the mounting bracket (8).
Push the guard into the bracket until it clicks into place.
Warning! Never use the tool without the guard.
Connecting the tool to the mains (fig. B)
Unless the tool is fitted with a mains cable, you will need to connect an extension cable to the power inlet.
Connect the female socket of a suitable extension cable to the power inlet of the tool.
Loop the cable through the cable restraint (7) as shown to prevent the extension cable from becoming detached during use.
Insert the mains plug into a mains outlet.
Warning! The extension cable must be suitable for outdoor use. When using a cable reel, always unwind the cable completely.
Use
Warning! Let the tool work at its own pace. Do not overload.
Carefully guide the cable in order to avoid accidentally cutting it. A good way to control the cable is by putting it over your shoulder.
4
Loading...