Aiwa CSD-TD26 User Manual
OPERATING INSTRUCTIONS INSTRUCCIONES DE MANEJO MODE D’EMPLOI
COMPACT DISC STEREO RADIO CASSETTE RECORDER
English : See page 2.
Español : Ver la página 10.
Français : Voir page 18.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
“CAUTION:TO REDUCE THE RISK OF
DO NOT REMOVE COVER (OR BACK).
REFER SERVICING TO QUALIFIED
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
For your convenience, record the model number (you will find it at the bottom of the unit) and serial number (you will find it in the battery compartment) in the space provided below. Please refer to them when you contact your AIWA dealer in case of difficulty.
Read the Operating Instructions carefully and completely before operating the unit. Be sure to keep the Operating Instructions for future reference. All warnings and cautions in the Operating Instructions and on the unit should be strictly followed, as well as the safety suggestions below.
1Water and moisture - Do not use this unit near water, such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, swimming pool, or the like.
2Heat - Do not use this unit near sources of heat, including heating vents, stoves, or other appliances that generate heat.
It also should not be placed in temperatures less than 5°C (41°F) or greater than 35°C (95°F).
3Mounting surface - Place the unit on a flat, even surface.
4Ventilation - The unit should be situated with adequate space around it so that proper heat ventilation is assured.
Allow 10 cm (4 in.) clearance from the rear and the top of the unit and 5 cm (2 in.) from each side.
-Do not place the unit on a bed, rug, or similar surface that may block the ventilation openings.
-Do not install the unit in a bookcase, cabinet, or airtight rack where ventilation may be impeded.
5Objects and liquid entry - Take care that objects or liquids do not get inside the unit through the ventilation openings.
6Carts and stands - When placed or mounted on a stand or cart, the unit
should be moved with care. Quick stops, excessive force, and
uneven surfaces may cause the unit or cart to overturn or fall.
7Condensation - Moisture may form on the CD pickup lens when:
-The unit is moved from a cold spot to a warm spot
-The heating system has just been turned on
-The unit is used in a very humid room
-The unit is cooled by an air conditioner
When this unit has condensation inside, it may not function normally. Should this occur, leave the unit for a few hours, then try to operate again.
8Wall or ceiling mounting - The unit should not be mounted on a wall or ceiling, unless specified in the Operating Instructions.
1Power sources - Use on batteries or AC house current, as specified in the Operating Instructions and marked on the unit.
2Polarization - As a safety feature, some units are equipped with polarized AC power plugs which can only be inserted one way into a power outlet. If it is difficult or impossible to insert the AC power plug into an outlet, turn the plug over and try again. If it still does not easily insert into the outlet, please call a qualified service technician to service or replace
the outlet. To avoid defeating the safety feature of the polarized plug, do not force it into a power outlet.
3AC power cord
-When disconnecting the AC power cord, pull it out by the AC power plug. Do not pull the cord itself.
-Never handle the AC power plug with wet hands, as this could result in fire or shock.
-Power cords should be firmly secured to avoid being bent, pinched, or walked upon. Pay particular attention to the cord from the unit to the power socket.
-Avoid overloading AC outlets and extension cords beyond their capacity, as this could result in fire or shock.
4Extension cord - To help prevent electric shock, do not use a polarized AC power plug with an extension cord, receptacle, or other outlet unless the polarized plug can be completely inserted to prevent exposure of the blades of the plug.
5When not in use - Unplug the AC power cord from the AC outlet or remove all the batteries if the unit will not be used for several months or more. When the cord is plugged in, a small amount of current continues to flow to the unit, even when the power is turned off.
Clean the unit only as recommended in the Operating Instructions.
Damage Requiring Service
Have the units serviced by a qualified service technician if:
-The AC power cord or plug has been damaged
-Foreign objects or liquid have got inside the unit
-The unit has been exposed to rain or water
-The unit does not seem to operate normally
-The unit exhibits a marked change in performance
-The unit has been dropped, or the cabinet has been damaged
DO NOT ATTEMPT TO SERVICE THE UNIT YOURSELF.
The OPE/BATT indicator lights up while the power is on.
Using on AC house current
Connect the AC cord as illustrated below.
to the AC inlet of the unit
supplied AC cord
to an AC outlet
(AC 120 V, 60 Hz)
Use only the supplied AC cord. Use with other cords
may result in the risk of fire.
Using on batteries
Open the lid of the battery compartment on the rear and insert eight R14 (size C) batteries, not supplied, with the 0and 9marks correctly aligned. Then close the lid.
To switch from AC power supply to battery power supply, disconnect the AC cord from the AC inlet.
When to replace the batteries
The OPE/BATT indicator becomes dim, the tape speed slows down, volume decreases, or sound is distorted during operation.
Notes on batteries
•Do not mix different types of batteries or old batteries with new ones.
•When the unit is not to be used for a long period, remove the batteries to prevent needless battery wear.
•Never recharge the batteries, apply heat to them or take them apart.
•Remove dead batteries.
If liquid leaks from the batteries, wipe thoroughly to remove.
DOWN – TUNING – UPPLAY/PAUSE/
A TUNER OPERATION
1 Press *RADIO/BAND repeatedly to select the desired band.
The power is turned on and the previously tuned station is received.
*or BAND on the remote control when the AC cord is connected
2 Pressr,t(TUNING DOWN, UP) to select a station.
During FM stereo reception, is displayed.
After listening, press TAPE/POWER/6STANDBY to turn the power off.
For better reception
Extend the rod antenna
The antenna is inside the
and orient it for the best
unit. Position the unit for
the best reception.
For quick tuning (Auto Search)
Keep r, tpressed until the tuner starts searching for a station. When a station is tuned to, the search stops.
If the broadcast signal is weak, it does not stop. To stop the search manually, press ror t.
To listen with the headphones
Connect headphones with a stereo mini plug to the \ jack on the rear of the unit.
-If an FM stereo broadcast contains noise, press the
button so that is displayed.
Noise is reduced, although reception is monaural. To restore stereo reception, press the button again.
* or MODE on the remote control
To change the AM tuning interval
The default setting of the AM tuning interval is 10 kHz/ step. If you use this unit in an area where the frequency allocation system is 9 kHz/step, change the interval as follows.
1Press RADIO/BAND to display FM.
2Press swhile pressing RADIO/BAND to display the AM frequency.
When the AM tuning interval is changed, the preset stations are cleared.
If the unit picks up noise from other electrical appliances nearby, like a TV or fluorescent lights, move the unit away.
You can preset up to 15 stations in each band.
1 Select a station.
2 Press *sSTOP/MEMORY once so that
“M” is displayed to store the station.
A station is assigned a preset number, beginning from 1 in consecutive order for each band.
* or son the remote control
3 Repeat steps 1 and 2.
The next station will not be stored if a total of 15 preset stations have already been stored for a band.
To listen to preset stations
Select a band then press ePLAY/PAUSE/PRESET repeatedly.
cPLAY on the remote control is also available (CSDTD66 only).
To select a preset number directly with the remote control
Press the numbered buttons
To select number 15, press +10 and 5. To select number 10, press +10 and 0.
To clear a preset station
Select the preset number first. Within 4 seconds, keep spressed until “M” and the preset number disappear in the display.
The higher numbers in the band are decreased by one.
Insert two R6 (size AA) batteries.
When the reach of the remote control signal is less than 5 meters (16 feet), replace the batteries.
The remote control may not operate correctly when:
-The unit is exposed to intense light, such as direct sunlight
-Objects block the remote control signal to the unit
To use the buttons on the remote control
Buttons on the remote control and the main unit with identical indications have the same functions.
To turn the power on
Press POWER to turn on the display.
When using the unit on the batteries, this button will not
turn the power on.
To turn the power off
Press POWER to turn off the display.
When one of the deck operation buttons is pressed, this button will not turn the power off.
To use the FUNCTION button
Each time FUNCTION is pressed while the power is on, the function is selected cyclically.
* applicable when one of the deck operation buttons is pressed
DOWN – TUNING – UPPLAY/PAUSE/
B CD OPERATION
1 Press CD.
The power is turned on.
2 Press CD OPEN to open the disc compartment. Place a disc with the printed side up and close the disc compartment.
Total number of tracks and total playing time are displayed. It will take about 15 seconds when loading a
3 Press *ePLAY/PAUSE/PRESET to start play.
The number of the track being played and elapsed playing time are displayed.
*or cPLAY on the remote control
sSTOP/MEMORY – Stops play.
* ePLAY/PAUSE/PRESET– Pauses play. To resume play, press again.
* or aPAUSE on the remote control
r,tSKIP/SEARCH – Searches for a particular point during playback. Keep ror tpressed and then release it.
– Skips to the beginning of a track. Press ror trepeatedly.
*REPEAT/SLEEP – Repeats a single track or all tracks. Select as follows.
[1 : A single track is played repeatedly. Select a track with ror t.
[: All tracks are played repeatedly.
*or REPEAT on the remote control
To start play when the power is off, press CD. The power is turned on and play of the loaded disc begins (Direct Play Function).
To select a track directly with the remote control
To select number 25, press +10, +10 and 5. To select number 10, press +10 and 0.
After listening, press TAPE/POWER/6STANDBY to turn the power off.
•Do not use irregular shape CDs (example: heartshaped, octagonal ones).
It may result in malfunctions.
•Do not place more than one disc in the disc compartment.
•Do not try to open the disc compartment during play.
•Do not touch the lens. Doing so may cause malfunctions.
•The unit may not play a
•Do not attach any seal or label to either side (the recordable side or the labeled side) of a
•Do not load an unrecorded
Up to 30 tracks can be programmed from the disc.
1 In stop mode, keep *sSTOP/MEMORY pressed until “M” flashes in the display.
* or son the remote control
2 Pressr,tto select a track, then presssSTOP/MEMORY to store it.
To select a track with the remote control (CSDTD66 only)
Press the numbered buttons
3 Repeat step 2 to program other tracks.
4 KeepsSTOP/MEMORY pressed until
“M” stops flashing to finish the program.
“M” remains displayed and indicates the unit stores the programmed tracks.
5 Presseto start play.
To check the program, press ror tin stop mode.
To clear the program, press sonce in stop mode so that “M” disappears in the display.
To change the programmed tracks, clear the program and repeat all the steps again.
Frequency range, antenna — FM: 87.5 - 108.0 MHz Rod antenna, AM: 530/531 - 1,710/1,602 kHz (10/9 kHz step) Ferrite bar antenna
Track format — 4 tracks, 2 channels / Frequency range
— Normal tape: 50 - 12,500 Hz (EIAJ) / Recording system — AC bias / Erasing system — Magnet erase / Heads — Recording/playback head (1), Erasure head
CD player section
Disc — Compact disc / Scanning method — Noncontact optical scanner (semiconductor laser)
Speaker — 100 mm cone type (2) / Output — Headphones jack (stereo
15 W / Dimensions (W × H× D) — 414× 183× 235 mm (163/8 × 71/4 × 93/8 in.) / Weight (excluding batteries) — 3.2 kg (7 lbs. 1 oz.) / Accessory — Remote control (1,
Specifications and external appearance are subject to change without notice.
Please check the copyright laws relating to recordings from disc, radio or external tape for the country in which the machine is being used.
If an erroneous display or malfunction occurs
Make sure that none of the deck operation buttons is pressed.
Press swhile pressing TAPE/POWER/6STANDBY. If the unit cannot be reset in the way above, disconnect the AC cord and remove all the batteries to turn off the display.
Leave the unit for a while and turn the power back on.
PAUSE STOP/EJECT FF
REW PLAY REC
VOL i, k
VOLUME N, M
C TAPE OPERATION
Use Type I (normal) tapes only.
INSERTING A TAPE
Press ZSTOP/EJECT to open the cassette holder and insert a tape with the exposed side up and the side to be played facing out.
Push the cassette holder to close.
PLAYING A TAPE
Press xPLAY while the power is off.
The power is turned on and play of the inserted tape begins.
The volume level is displayed during tape operation.
ZSTOP/EJECT – Stops play. The power will be automatically turned off.
aPAUSE – Pauses play. To resume play, press again.
fFF/ gREW – Fast forwards/ rewinds. To stop the winding, press Z.
To prevent accidental erasure
Break off the plastic tabs on the cassette tape with a screwdriver or other pointed tool after recording.
To record on the tape again
Cover the tab openings with adhesive tape, etc.
Tab for side A
Note that recording is done on only one side of the tape.
1 Insert a tape with the side to be recorded facing out.
2 Get ready to record from the source.
To record from a CD, press CD and load the disc.
To record from a radio broadcast, press RADIO/ BAND and tune to a station.
3 Press wREC to start recording. xPLAY is pressed simultaneously.
When the selected function is CD, CD play and recording starts simultaneously.
To record only the selected tracks of a CD
1Follow steps 1 to 4 of PROGRAMMED PLAY on page 7 to program tracks.
To stop recording, press ZSTOP/EJECT. To stop CD play, press sSTOP/MEMORY.
To pause recording, press aPAUSE. To resume recording, press again.
To erase recording, press wREC while the power is off.
After recording, press TAPE/POWER/6STANDBY to turn the power off.
Volume or tone adjustment does not affect recording.
Press VOLUME Nor M. The volume level is displayed as a number from 0 to MAX (25).
•The volume level is automatically set to 14 if the power is turned off when the volume level is set to 15 or more. (except when turning the power back on within 4 seconds)
•Pressing DISPLAY on the remote control displays the adjusted volume level
The equalizer mode changes to R (Rock), P (Pop), J (Jazz) or no equalization, cyclically.
Rock - Emphasizes the high and low range of music.Pop - Emphasizes voice and midrange of music.Jazz - Emphasizes the low range of music.
* or EQ on the remote control
This system provides a rich, three dimensional sound area for stereo sources.
You can enjoy more enhanced sound.
Press QSOUND and the QSOUND indicator lights up.
•At higher volumes, turning QSOUND on may cause sound distortion. In this case, make the volume down.
To clean the cabinet
Use a soft cloth lightly moistened with mild detergent solution. Do not use strong solvents such as alcohol, benzine or thinner.
To clean the heads
When the tape heads are dirty;
-high frequency sound is not emitted
-the sound is not adequately high
-the sound is
-the tape cannot be erased
-the tape cannot be recorded on
SETTING THE SLEEP TIMER
The unit can be turned off automatically at a specified time.
1 Keep REPEAT/SLEEP pressed until “30” flashes in the display.
2 Within 4 seconds, pressrortto specify the time until the power is turned off.
Each time it is pressed, the time changes between 10 and 90 minutes in
While the sleep timer works,
the dot keeps flashing.
To check the time remaining until the power is
Repeat step 1 shown above. The remaining time is
displayed for 4 seconds.
To cancel the sleep timer
Display the remaining time and press ror t repeatedly until OFF is displayed.
If the unit is turned off during tape playback, xon the deck will not be released. Press Zto release x.
After every 10 hours of use, clean the tape heads with a head cleaning cassette.
Use separately sold
Refer to the instructions of the cleaning cassette for details.
To clean the lens
Use a cotton swab slightly moistened with cleaning fluid. Wipe gently from the center to the edge.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
... Reorient or relocate the receiving antenna.
... Increase the separation between the equipment and receiver.
... Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
... Consult the dealer or an experienced radio/TV technician for help.
Modifications or adjustments to this product, which are not expressly approved by the manufacturer, may void the user’s right or authority to operate this product.
Printed in China