ZyXEL Communications NWD670SH User Manual
FCC Statement
ZyXEL
NWD670SH
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user authority to operate the equipment.
The device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not
cause
including
The user’s manual or instruction manual for an intentional or unintentional radiator
shall
party
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide
This
installed
to
radio communications.
However, there is no guarantee that interference will not occur in a particular
installation.
reception,
encouraged
Reorient
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver
Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.
t
This
or transmitter.
This module is intended for OEM integrator.The OEM integrator is still responsible for the FCC compliance
requirement of the end prouduct, which integrates this module.
20cm minimum distance has to be able to be maintained between the antenna and the users for the host
this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for
an population/uncontrolled environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer could void the user's authority
to operate this equipment.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation
with the antenna while this end product is installed and operated. The end user has to be informed that
the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied.
The end user has to also be informed that any changes or modifications not
manufacturer could void the user's authority to operate this equipment. If the size of the end product is
smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users
manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following
" Contains TX FCC ID:I88NWD670SH".
If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to
also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Exposure Manual Information That Must be Included
harmful interference, and (2) this device must accept any interference received,
interference that may cause undesired operation.
caution the user that changes or modifications not expressly approved by the
responsible for compliance could void the user’s authority to operate the
reasonable protection against harmful interference in a residential installation.
equipment generates, uses and can radiate radio frequency energy and, if not
and used in accordance with the instructions, may cause harmful interference
If
this equipment does cause harmful interference to radio or television
which can be determined by turning the equipment off and on, the user is
to
try to correct the interference by one or more of the following measures:
or
relocate the receiving antenna.
is connect
CAUTION:
ransmitter must not be co-located or operating in conjunction with any other antenna
ed.
expressly approved by the
The users manual for end users must include the following information in a prominent
location
requirements, the antenna used for this transmitter must be installed to provide a
separation
operating
"IMPORTANT NOTE: To comply with FCC RF exposure compliance
distance of at least 20 cm from all persons and must not be co-located or
in
conjunction with any other antenna or transmitter."
Additional Information That Must be Provided to OEM Integrators
The end user should NOT be provided any instructions on how to remove or install the
device.
Service Center in U.S.A
Company Name : ZyXEL Technologies, Inc..
Company Address: No. 6, Innovation Road II, Science Park, Hsin-Chu, Taiwan
1. Introduction
IEEE802.11b/g
wireless
54Mbps in a wireless LAN environment.
NWD670SH
Camera series and Internet Video Server gives you wireless access the web and
network resource without the wire.
NWD670SH
128 bit and 256 bit of WEP (Wired Equivalent Privacy) data encryption. With Direct
Spread Spectrum Signaling (DSSS) and Orthogonal Frequency Division Multiplexing
(OFDM), domain access control, WEP encryption and group security, the modules will
safeguard
NWD670SH
real-time
High Power
network applications based on the IEEE 802.11g standard offering a data rate of
is designed for Access Point, Router, ATU-R, Printer Server series, IP
provides high-speed access to network resources and has built-in 40/64-bit,
all your wireless data transmissions from your nosy neighbors.
allows you to take full advantage of your devices mobility with access to
information and online services anytime and anywhere.
MiniPCI
Wireless LAN Card(SuperG) is
the perfect solution for your
2. Feature
•
Compatible with IEEE 802.11b/g
•
MiniPCI Compliant Interface
•
High Transmitting Power
•
High Receiving Sensitivity
•
Multi-Antenna-Connector Supported
.
Loading...