ZyXEL Communications NWD670 User Manual
ZyXEL
NWD670
802.11b/g Wireless MiniPCI Card
User’s Manual
Release 0.1
ZyXEL Communications Corp. Proprietary & Confidential Information
i
Specifications are subject to change without notice
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
(15.21)
Warning: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user authority to operate the
equipment.
15.19 (a)(3)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
The users manual or instruction manual for an intentional or unintentional radiator shall
caution the user that changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
CAUTION:
1. To comply with FCC RF exposure compliance requirements, a separation distance of at
least 20 cm must be maintained between the antenna of this device and all persons.
2. This Transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
CAUTION:
This device is intended only for OEM integrators under the following conditions:
ZyXEL Communications Corp. Proprietary & Confidential Information
ii
Specifications are subject to change without notice
1. This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the FCC
radio frequency exposure limits, human proximity to the antenna (installed to end
product) shall not be less than 20 cm (8 inches) during normal operation.
1. This Transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter
As long as the 2 conditions above are met, further transmitter testing will
not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed (for example, digital device emission, PC peripheral
requirements, etc.).
Additional Information that Must be Provided to OEM Integrators:
The end user should NOT be provided any instructions on how to remove or install the device.
IMPORTANT NOTE.
1) In the event that these conditions cannot be met (for example certain laptop configurations or
co-location with another transmitter), then the FCC authorization is no lon ger con sidere d valid and
the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and obtaining a separate
FCC authorization.
2) To comply with FCC RF exposure compliance requirements, the antenna used for this
transmitter must be installed to provide a separation distance of at least 20 cm from all persons and
must not be co-located or operating in conjunction with any other antenna or transmitter."
End Product Labeling
This transmitter module is authorized only for use in devices where the antenna may be installed
such that 20 cm may be maintained between the antenna and users (for exampl e access points,
routers, wireless ASDL modems, and similar equipment). The final end product must be labeled in
a visible area with the following: "Contains TX FCC ID: I88NWD670
ZyXEL Communications Corp. Proprietary & Confidential Information
iii
Specifications are subject to change without notice
注意 !
依據 低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用
者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現
有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信規定作業之無線電信。低功率射頻電機須忍受
合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
ZyXEL Communications Corp. Proprietary & Confidential Information
iv
Specifications are subject to change without notice
Loading...