Page 1
Get connected
Vodafone Mobile Wi-Fi
R218z
Vodafone
Power to you
1 Open 2 Insert microSIM 3 Charge
Note: usage of SIM card adapters
could damage the SIM card card
reader.
Your Vodafone Mobile Wi-Fi
network name & password
SSID sticker here
SSID sticker here
4 Start 5 Connect
Choose Wi-Fi on your computer,
smartphone or tablet settings, then
select your Mobile Wi-Fi network
name.
Enter the password to connect and
open the web app.
When you first connect to the
network you may be asked to
activate your SIM.
Push and hold
the power key
If you’re asked to unlock your
SIM card, go to
http://vodafonemobile.wifi
and enter the PIN for your SIM.
Turn over for more information about
using your Vodafone Mobile Wi-Fi.
Page 2
Using the web interface at vodafonemobile.wifi
LED overview
You can find the web app on
vodafonemobile.wifi
if it doesn’t appear
automatically when you
connect. Then login using
the password admin.
Then you can see your
network and Wi-Fi status,
how much data you have
used, get help and support,
and even send and receive
SMS messages from your
computer.
Note for UK u sers only : if you are a Con tract
customer y ou can send a nd receive S MS. Pay
As You Go cu stomers wil l only recei ve netwo rk
notif ications
Battery
Low
Charging
Good
Wi-Fi signal
Wi-Fi off
WPS active
Wi-Fi (WLAN) active
SMS text messages
No SMS
(slow blinking:)
SMS Inbox full
(fast blinking:)
Device update available at
vodafonemobile.wifi
Unread SMS
Mobile Broadband
Connected to 4G
Download the monitor app
The Vodafone Mobile Wi-Fi
Monitor app is a quick and easy
way to monitor your network on a
smartphone or tablet.
Download the app from your device’s
app store, or scan the appropriate
QR code here to take you to the app
store.
iOS
(iPhone or
iPad)
Android
(smartphone or
tablet)
Connected to 2G/3G
Low signal
No SIM detected, or PIN
code required
To find out more about your
device, please visit
vodafone.com/r218z
™
The term “Mobile Broadband” together
with the ‘birds’ design is a trademark of
GSMC Limited.
© Vodafone Group 2018. Vodafone and the Vodafone logos
are trade marks of Vodafone Group. Any product or company
names mentioned herein may be the trade marks of their
respective owners.
Page 3
is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal
During SAR testing, this device was set to transmit at its highest certified powe
. Although the SAR is determined at the highest certified power level, the
is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the cl
The exposure standard for wireless devices employing a unit of measurement is known as the Specific Absorption Rate, or SAR.
for general population /uncontrolled exposure limits in ANSI/IEEE C95.1
device
is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC I
For this device, the highest reported SAR value for usage near the body
While there may be differences between the SAR levels of various
worn operation is based on a separation distance of
exposure level compliant or lower to the reported level. To support body
worn accessory, which contains metal, was not tested and certified, and using such body
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the manufact
located or operating in conjunction with any other antenna or transmitter.
h the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This e
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, ther
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Communications Commission of the United States.
eless base station antenna, the lower the power
1992 and had been tested in accordance with the measurement methods and procedures
eported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model
10 mm
worn operation, choose the belt clips or holsters, which do not contain metallic components, to maintain a separation of
worn accessory should be avoided.
FCC RF Exposure Information (SAR)
This device
separation of 10 mm
device
output.
This device is complied with SAR
specified in IEEE1528.
The FCC has granted an Equipment Authorization for this model
device
SAR compliance for body-
between this device and your body.
RF exposure compliance with any body-
with all r
is 1.340 W/kg.
devices and at various positions, they all meet the government requirements.
10 mm between the unit and the human body. Carry this device at least
-
FCC Regulations
CAUTION:
The antenna(s) used for this transmitter must not be co-
NOTE:
This equipment has been tested and found to comply wit
installation. If this equipment does
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
urer could void the user’s authority to operate the equipment.
near the body with the
oser you are to a wir
W/kg.
-
D: SRQ-R218Z.
away from your body to ensure RF
-
equency energy and, if not
user is encouraged to try to correct the
10 mm
Loading...